Parkside PSBSA 20-LI B2 Instrucțiuni de utilizare

3-IN-1 CORDLESS IMPACT DRILL PSBSA 20-Li B2

3-IN-1-AKKU-SCHLAGBOHR-

SCHRAUBER

Originalbetriebsanleitung

IAN 326374_1904

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ ΚΡΟΥΣΤΙΚΟ

ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ 3 ΣΕ 1

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

УДАРНА БОРМАШИНА 3 В 1

Превод на оригиналното ръководство за експлоатация

MAȘINĂ DE ÎNȘURUBAT ȘI GĂURIT

CU PERCUŢIE ȘI ACUMULATOR, 3 ÎN 1

Traducerea instrucţiunilor de utilizare original

3-U-1 AKU UDARNA

BUŠILICA-ODVIJAČ

Prijevod originalnih uputa za uporabu

AKU UDARNA BUŠILICA-

ODVIJAČ 3 U 1

Prevod originalnog uputstva za upotrebu

3-IN-1 CORDLESS IMPACT DRILL

Translation of the original instructions

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 13

RS Prevod originalnog uputstva za upotrebu Strana 27

RO Traducerea instrucţiunilor de utilizare original Pagina 41

BG Превод на оригиналното ръководство за експлоатация Cтраница 55

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 71

DE / AT / CH Originalbetriebsanleitung Seite 85

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

Charging

times

Charging

currents

2 Ah

Battery pack

PAP 20 A1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3

max. 2.4 A

Charger

PLG 20 A1

60 min

2.4 A

90 min

2.4 A

120 min

2.4 A

max. 3.5 A

Charger

PLG 20 A2

60 min

2.4 A

60 min

3.5 A

80 min

3.5 A

max. 4.5 A

Charger

PLG 20 A3

45 min

3.5 A

45 min

4.5 A

60 min

4.5 A

20V max.

18V

All Parkside tools and the chargers PLG 20 A1 / PLG 20 A2 / PLG 20 A3 of the X20V Team series

are compatible with the PAP 20 A1 / PAP 20 A2 / PAP 20 A3 battery pack.

PSBSA 20-Li B2

GB

│

CY

│

1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 2

General power tool safety warnings .................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 3

3. Personal safety ............................................................ 4

4. Power tool use and care .................................................... 4

5. Battery tool use and care .................................................... 5

6. Service .................................................................. 5

Safety instructions for drills .........................................5

Original accessories / auxiliary equipment ........................................ 6

Safety guidelines for battery chargers ............................................ 6

Before use .......................................................6

Charging the battery pack (see ﬁg. A) ............................................ 6

Attaching/disconnecting the battery pack to/from the appliance ....................... 7

Checking the battery charge level ............................................... 7

Fitting the additional handle .................................................... 7

Changing tools .............................................................. 7

Torque preselection/selecting the operating mode .................................. 7

2-speed gearbox ............................................................ 7

Use .............................................................8

Switching on and oﬀ ......................................................... 8

Adjusting the rotational speed .................................................. 8

Changing the direction of rotation ............................................... 8

Tips and tricks ............................................................... 8

Maintenance and cleaning ..........................................8

Kompernass Handels GmbH warranty ...............................9

Service .........................................................10

Importer .......................................................10

Disposal ........................................................10

Translation of the original Conformity Declaration .....................11

Ordering a replacement battery ....................................12

Telephone ordering ......................................................... 12

PSBSA 20-Li B2

■ 2

│

GB

│

CY

3-IN-1 CORDLESS IMPACT DRILL

PSBSA 20-Li B2

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

This appliance is intended for screwing in and

removing screws as well as drilling in wood, metal,

ceramic and plastic and impact drilling in bricks

and masonry. It is not suitable for impact drilling

in natural stone such as granite. The light on this

appliance is intended to illuminate the immediate

work area of the appliance.

Use this product only as described and for the

areas of applications speciﬁed. The appliance is

not intended for commercial use. Any other usage

or modiﬁcation of the appliance is deemed to be

improper and carries a signiﬁcant risk of accidents.

The manufacturer accepts no responsibility for

damage(s) attributable to misuse.

Features

Speed selector

Rotation direction switch/lock

ON/OFF switch / Speed control

Bit

Battery charge level button

Battery display LED

Battery pack*

Release button for the battery pack

LED work light

Additional handle

Chuck

Torque preselection ring

High-speed charger*

Red charge control LED

Green charge control LED

Package contents

1 3-in-1 Cordless Impact Drill PSBSA 20-Li B2

1 additional handle

2 bits PZ1 & PZ2 (50mm)

1 carrying case

1 set of operating instructions

Technical data

3-in-1 Cordless Impact Drill: PSBSA 20-Li B2

Rated voltage: 20 V (DC)

Gearbox: 2 speed gearbox

Rated idle speed: 1st gear: n

0

0–440 rpm

2nd gear: n

0

0–1650 rpm

Hammer frequency: 0–26400 bpm

Max. torque: 45 Nm

Torque levels: 1–20 + 1 drill level /

+ 1 hammer level

Chuck capacity:

: Ø max. 13 mm

Max. drill diameter: 30 mm for wood

15 mm for tiles

13 mm for steel

Battery: PAP 20 A1*

Type: LITHIUM ION

Rated voltage: 20 V

(DC)

Capacity: 2 Ah

Cells: 5

High-speed battery charger: PLG 20 A1*

INPUT:

Rated voltage: 230–240 V

~

, 50 Hz

(AC)

Rated power

consumption: 65 W

Fuse (internal): 3.15 A

T3.15A

OUTPUT:

Rated voltage: 21.5 V (DC)

Rated current: 2.4 A

Charging time: approx. 60 min

Protection class: II / (double insulation)

*BATTERY AND CHARGER ARE NOT INCLUDED

Noise emission value:

Noise measurement value determined in accordance

with EN 62841. The A-rated noise level of the

power tool is typically as follows:

PSBSA 20-Li B2

GB

│

CY

│

3 ■

Sound pressure level: L

PA

= 86.7dB (A)

Uncertainty K: K

PA

= 3 dB

Sound power level: L

WA

= 97.7 dB (A)

Uncertainty K: K

WA

= 3 dB

Vibration emission value:

Total vibration values (vector total of three direc-

tions) determined in accordance with EN 62841:

Hammer drilling in concrete:

a

H,ID

= 9.875 m/s

2

Drilling in metal:

a

h,D

= 3.475 m/s

2

Uncertainty K = 1.5 m/s

2

Screws:

<2.5 m/s

2

Uncertainty K = 1.5 m/s

2

Wear hearing protection!

NOTE

► The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with

a standardised test procedure and can be

used for comparison of the power tool with

another tool.

► The speciﬁed total vibration values and the

noise emission values can also be used to

make a provisional load estimate.

WARNING!

► Depending on the manner in which the power

tool is being used, and in particular the kind of

workpiece that is being worked, the vibration

and noise emission values can deviate from

the values given in these instructions during

actual use of the power tool.

► Try to keep the load as low as possible.

Measures to reduce the vibration load are,

e.g. wearing gloves and limiting the working

time. Wherein all states of operation must be

included (e.g. times when the power tool is

switched oﬀ and times where the power tool is

switched on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings, instructions, il-

lustrations and speciﬁcations provided with

this power tool. Failure to follow all instruc-

tions listed below may result in electric shock,

ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term „power tool“ in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools cre-

ate sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or ground-

ed surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

PSBSA 20-Li B2

■ 4

│

GB

│

CY

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such

as a dust mask, non-slip safety shoes, hard hat or

hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites ac-

cidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles. A careless

action can cause severe injury within a fraction

of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detach-

able, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool ac-

cidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation. If

damaged, have the power tool repaired be-

fore use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power

tool for operations diﬀerent from those intended

could result in a hazardous situation.

PSBSA 20-Li B2

GB

│

CY

│

5 ■

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in unex-

pected situations.

5. Battery tool use and care

a) Recharge only with the charger speciﬁed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

ﬁre when used with another battery pack.

b) Use power tools only with speciﬁcally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁre.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from

one terminal to another. Shorting the battery

terminals together may cause burns or a ﬁre.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂush with water.

If liquid contacts eyes, additionally seek medi-

cal help. Liquid ejected from the battery may

cause irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable behaviour

resulting in ﬁre, explosion or risk of injury.

f) Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre

or temperature above 130 °C (265°F) may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instruc-

tions. Charging improperly or at temperatures

outside the speciﬁed range may damage the

battery and increase the risk of ﬁre.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries!

Protect the rechargeable battery from

heat, for example from continuous

exposure to sunlight, ﬁre, water and

moisture. There is a risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

b) Never service damaged battery packs. Service

of battery packs should only be performed by

the manufacturer or authorized service providers.

Safety instructions for drills

Safety instructions for all work

■ Wear ear muﬀs when hammer-drilling. Expo-

sure to loud noise can lead to hearing loss.

■ Use the additional handle. Loss of control can

lead to injuries.

■ Hold the power tool only by the insulated

handles when you are carrying out work

in which the accessory tool may come into

contact with concealed power cables or the

tool’s own power cord. Contact with a live wire

may electrify exposed metal parts of the tool and

could give the operator an electric shock.

■ You can collect any dust produced using a

vacuum cleaner, for example.

Safety information for using long drill bits

■ Do not use a higher rotational speed than

the maximum permissible speed. At higher

speeds, the drill bit can bend slightly if allowed

to turn freely without being in contact with the

workpiece and this can lead to injuries.

PSBSA 20-Li B2

■ 6

│

GB

│

CY

■ Always start drilling at a low speed and with

the drill bit in contact with the workpiece. At

higher speeds, the drill bit can bend slightly if

allowed to turn freely without being in contact

with the workpiece and this can lead to injuries.

■ Do not exert excessive pressure and only

along the length of the drill bit (no lateral

pressure). Drill bits can bend and break, which

can lead to a loss of control and injuries.

Original accessories / auxiliary

equipment

■ Use only the accessories and additional

equipment which are speciﬁed in the operat-

ing instructions and are compatible with the

appliance.

WARNING!

■ Do not use any accessories which are not

recommended by PARKSIDE. This can lead to

an electric shock and ﬁre.

Safety guidelines for battery chargers

■ This appliance may be used

by children aged 8 years and

above and by persons with lim-

ited physical, sensory or mental

capabilities or lack of experi-

ence and knowledge, provided

that they are under supervision

or have been told how to use

the appliance safely and are

aware of the potential risks. Do

not allow children to use the ap-

pliance as a toy. Cleaning and

user maintenance tasks may not

be carried out by children unless

they are supervised.

■ To avoid potential risks, dam-

aged mains cables should be re-

placed by the manufacturer, their

customer service department or

a similarly qualiﬁed person.

The charger is suitable for indoor use

only.

WARNING!

■ To avoid potential risks, damaged mains ca-

bles should be replaced by the manufacturer,

their customer service department or

a similarly qualiﬁed person.

ATTENTION!

♦ This charger can only charge the following bat-

teries: PAP 20 A1 / PAP 20 A2 / PAP 20 A3

.

♦ A current list of battery compatibility can be

found at www.lidl.de/Akku.

Before use

Charging the battery pack (see ﬁg. A)

CAUTION!

► Always unplug the appliance before you

remove the battery pack from or connect the

battery pack to the charger.

♦ Connect the battery pack

to the high-speed

battery charger (see ﬁg. A).

♦ Insert the power plug into the socket. The control

LED

lights up red.

♦ The green LED

indicates that the charging

process is complete and the battery pack is

ready.

CAUTION!

♦ If the red control LED

ﬂashes, this means

that the battery pack has overheated and

cannot be charged.

♦ If the red and green control LEDs

both

ﬂash, this means that the battery pack is

broken.

PSBSA 20-Li B2

GB

│

CY

│

7 ■

♦ Push the battery pack back into the appliance.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack:

♦ Push the rotation direction switch

into the

middle position (lock). Allow the battery pack

to click into the handle.

Removing the battery pack:

♦ Press the release button

and remove the

battery pack.

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram).

The status/remaining charge will be shown on

the battery display LED

as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Fitting the additional handle

♦ Screw the additional handle onto the left or

right of the appliance depending on how you

work.

Changing tools

Your cordless screwdriver has a fully automatic

spindle lock .

When the motor is stopped, the power train locks

so that the chuck

can be opened by turning

it . Once you have attached the desired tool

and tightened it by turning the chuck , you can

continue working. The spindle lock is automatically

released when the motor starts (ON/OFF switch

pressed).

Torque preselection/selecting the

operating mode

You can adjust the torque on the torque preselector

and select between the drill setting and the

hammer drill setting

.

♦ Select a low level for small screws or soft

materials.

♦ Select a high level for large screws, hard

materials or removing screws.

♦ Select the drill setting for drilling work by adjusting

the torque selection ring to the position

.

♦ Select the hammer drill setting for hammer

drilling work by adjusting the torque selection

ring to the position

.

2-speed gearbox

CAUTION!

► Operate the speed selection switch

only

when the appliance is at a standstill. Other-

wise the appliance can be damaged.

In ﬁrst gear (speed selector switch

in

position: 1)

you can reach a speed of approx. 440 rpm and a

high torque. This setting is suitable for all screwing

work but also for the use of accessories.

In second gear (speed selector switch

in

position: 2)

you can reach a speed of approx. 1650 rpm for

carrying out drilling work.

PSBSA 20-Li B2

■ 8

│

GB

│

CY

Use

Switching on and oﬀ

Switching on:

♦ To start the appliance, press the ON/OFF

switch

and keep it pressed in.

The LED work light lights up when the ON/OFF

switch is depressed lightly or fully. This allows

for illumination of the work area in low lighting.

Switching oﬀ:

♦ Release the ON/OFF switch

to switch oﬀ the

appliance.

Adjusting the rotational speed

Press the ON/OFF switch lightly for a low

speed. Increasing the pressure increases the speed.

NOTE

► The integrated motor brake ensures rapid

stoppage.

Changing the direction of rotation

♦ Change the direction of rotation by pressing the

rotational direction switch towards the left

or right.

Tips and tricks

Tip! This symbol indicates proper

baviour.

♦ Before operating the appliance, check whether

the screw or drill bit is correctly positioned, i.e.

centred in the drill chuck.

♦ Screw bits are labelled according to their di-

mensions and their shape. If you are uncertain,

always check whether the bit ﬁts tightly in the

screw head without any free play.

Torque:

♦ Smaller screws/bits can be damaged if you set

the torque or rotational speed too high.

Hard screw joints (in metal):

♦ Particularly high torques occur, for example, in

metal screw joints made using drive sockets.

Select a low rotational speed.

Soft screw joints (e.g. in soft wood):

♦ Again, use a low rotational speed, for example

to avoid damaging the surface of the wood on

contact with the screw head. Use a countersink.

When drilling in wood, metal and other

materials, observe the following:

♦ Use a high speed for drill bits with small dia-

meter and a low speed for drill bits with large

diameter.

♦ Select a low speed for hard materials and a

high speed for soft materials.

♦ Mark the spot where you want to drill using a

centre punch or nail. Select a low rotational

speed when starting.

♦ Pull the rotating drill bit from the hole repeatedly

to remove dust and chips and clear the hole.

Drilling in metal:

♦ Use a metal drill (HSS). For optimum results,

you should cool the drill bit with oil.

Metal drill bits can also be used to drill into

plastics. Start with a 3 mm diameter drill bit

and then increase the size until the desired hole

diameter is achieved.

Drilling in brick:

♦ Use a carbide-tipped masonry drill.

(max. recommended hole diameter: Ø 15 mm)

Drilling in wood:

♦ Use a wood drill with a lathe centre; for deep

holes, use an auger bit; for large-diameter

holes, use a Forstner bit. Small screws can be

screwed directly into soft wood.

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

The cordless combi drill is maintenance-free.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Never allow liquids to get into the appliance.

PSBSA 20-Li B2

GB

│

CY

│

9 ■

■ Use a soft, dry cloth to clean the housing.

Never use petrol, solvents or cleansers which

can damage plastic.

■ If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level is

between 50% and 80%. The optimum storage

environment is cool and dry.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase (re-

ceipt) within the three-year warranty period, along

with a brief written description of the fault and of

when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product parts

subject to normal wear and tear or to fragile parts

which could be considered as consumable parts

such as switches, batteries or parts made of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly main-

tained. The directions in the operating instructions

for the product regarding proper use of the product

are to be strictly followed. Uses and actions that are

discouraged in the operating instructions or which

are warned against must be avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or bot-

tom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be pro-

vided to you. Ensure that you enclose the proof

of purchase (till receipt) and information about

what the defect is and when it occurred.

PSBSA 20-Li B2

■ 10

│

GB

│

CY

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to

the Lidl service page (www.lidl-service.com) where

you can open your operating instructions by enter-

ing the item number (IAN) 123456.

Service

WARNING!

► Have the power tool repaired by the service

centre or a qualiﬁed electrician and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

► Always ensure that the power plug or

the mains cable is replaced only by the

manufacturer of the appliance or by an

approved customer service provider. This

will ensure that the safety of the appliance is

maintained.

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

IAN 326374_1904

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Disposal

The packaging is made from environmen-

tally friendly material and can be dis-

posed of at your local recycling plant.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Do not dispose of batteries in your

normal household waste!

Remove the batteries from the appliance before

disposal.

Defective or worn-out rechargeable batteries must

be recycled according to Directive 2006/66/EC.

Take the battery pack and/or appliance to a nearby

collection facility.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Dispose of the packaging in an

environmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary.

The packaging material is labelled

with abbreviations (a) and numbers

(b) with the following meanings:

1–7: Plastics,

20–22: Paper and cardboard,

80–98: Composites.

Your local community or municipal

authorities can provide information on

how to dispose of the worn-out

product.

PSBSA 20-Li B2

GB

│

CY

│

11 ■

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EC Low Voltage Directive

(2014 / 35 / EU) (charger only)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object

of the declaration described above complies with the requirements of the Directive 2011/65/EU

of the European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous

substances in electrical and electronic appliances.

Applied harmonised standards:

EN 62841-1:2015

EN 62841-2-1:2018

EN 55014-1:2017

EN 55014-2:2015

EN 60335-2-29:2004/A2:2010

EN 60335-1:2012/A11:2014

EN 62233:2008

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type/appliance designation: 3-in-1 Cordless Impact Drill PSBSA 20-Li B2

Year of manufacture: 08 - 2019

Serial number: IAN 326374_1904

Bochum, 16/08/2019

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

PSBSA 20-Li B2

■ 12

│

GB

│

CY

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the Internet on

www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

► Online ordering of replacement parts is not possible in all countries. In this case, please contact the

Service hotline.

Telephone ordering

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: [email protected]

To ensure a fast processing of your order, have the article number of you appliance to hand

(e.g. IAN 326374) in case of questions. The article number can be found on the type plate or the title

page of these instructions.

PSBSA 20-Li B2

HR │ 13 ■

Sadržaj

Uvod ..........................................................14

Namjenska uporaba ........................................................14

Oprema .................................................................. 14

Opseg isporuke ............................................................14

Tehnički podaci ............................................................ 14

Opće sigurnosne napomene za uporabu električnog alata ..............15

1. Sigurnost na radnom mjestu ................................................. 15

2. Električna sigurnost. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3. Sigurnost osoba .......................................................... 16

4. Korištenje i rukovanje električnim alatom .......................................16

5. Korištenje i rukovanje baterijskim alatom ....................................... 17

6. Servis ..................................................................17

Sigurnosne napomene za bušilice ...................................18

Originalni pribor / dodatni uređaji .............................................18

Sigurnosne napomene za punjače .............................................. 18

Prije uključivanja uređaja .........................................19

Punjenje paketa baterije (vidi sliku A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Umetanje paketa baterija u uređaj/vađenje ...................................... 19

Provjera stanja baterije .......................................................19

Montiranje dodatne ručke .................................................... 19

Zamjena alata .............................................................19

Predodabir okretnog momenta / odabir načina rada ...............................20

2-stupanjski prijenosnik .......................................................20

Puštanje u rad ...................................................20

Uključivanje/isključivanje .....................................................20

Podešavanje broja okretaja ...................................................20

Promjena smjera okretanja .................................................... 20

Savjeti i trikovi .............................................................. 20

Održavanje i čišćenje .............................................21

Jamstvo tvrtke Kompernass Handels GmbH ..........................21

Servis ..........................................................23

Uvoznik ........................................................23

Zbrinjavanje ....................................................23

Prijevod originalne izjave o sukladnosti .............................24

Narudžba zamjenske baterije .....................................25

Telefonska narudžba ........................................................25

PSBSA 20-Li B2

■ 14 │ HR

3-U-1 AKU UDARNA BUŠILICA-

ODVIJAČ PSBSA 20-Li B2

Uvod

Čestitamo na kupnji Vašeg novog uređaja. Time

ste se odlučili za vrlo kvalitetan proizvod. Upute

za uporabu sastavni su dio ovog proizvoda. One

sadrže važne napomene za sigurnost, rukovanje i

zbrinjavanje. Prije uporabe proizvoda upoznajte se

sa svim napomenama za rukovanje i sa svim sigur-

nosnim napomenama. Proizvod koristite isključivo

na opisani način i u navedenim područjima upora-

be. U slučaju predaje proizvoda trećim osobama,

priložite i također predajte i svu dokumentaciju.

Namjenska uporaba

Ovaj uređaj je namijenjen za uvrtanje i odvijanje

vijaka, kao i za bušenje u drvetu, metalu, keramici

i plastici i za udarno bušenje u cigli i zidovima.

Ovaj uređaj nije prikladan za udarno bušenje u

prirodnom kamenu, na primjer granitu. Svjetlo ovog

uređaja namijenjeno je za osvjetljavanje neposred-

nog radnog područja uređaja.

Uređaj koristite samo na opisani način i u opisanim

područjima uporabe. Uređaj nije namijenjen za

komercijalnu uporabu. Svaki drugi način uporabe

i svaka izmjena uređaja smatra se nenamjenskom i

krije znatnu opasnost od nezgode. Proizvođač ne

preuzima odgovornost za štete nastale nenamjen-

skim korištenjem uređaja.

Oprema

Prekidač za odabir stupnja prijenosa

Prekidač za odabir smjera okretanja / blokada

Prekidač UKLJ/ISKLJ / Regulacija broja okretaja

bitova

Tipka za stanje baterije

LED indikator baterije

Paket baterija*

Tipka za deblokadu paketa baterija

LED radna svjetiljka

Dodatna ručka

Prihvatnik alata

Predodabir okretnog momenta

Brzi punjač*

Crvena LED svjetiljka za kontrolu punjenja

Zelena LED svjetiljka za kontrolu punjenja

Opseg isporuke

1 3-u-1 aku udarna bušilica-odvijač

PSBSA 20-Li B2

1 Dodatna ručka

2 bita PZ1 & PZ2 (50mm)

1 torbica

1 Upute za uporabu

Tehnički podaci

3-u-1 aku udarna bušilica-odvijač:

PSBSA 20-Li B2

Nazivni napon: 20 V

(istosmjerna struja)

Prijenosnik: 2-stupanjski prijenosnik

Nazivni broj okretaja

u praznom hodu: 1. stupanj: n

0

0 - 440 min

-1

2. stupanj: n

0

0 - 1650 min

-1

Frekvencija udaraca: 0 - 26400 min

-1

Maks. okretni moment: 45 Nm

Stupnjevi okretnog

momenta: 1 - 20 + 1 stupanj bušenja/

+ 1 stupanj udaranja

Kapacitet stezne glave:

: Ø maks. 13 mm

Maks. promjer bušenja: 30 mm za drvo

15 mm za ciglu

13 mm za čelik

Bateriju: PAP 20 A1*

Tip: LITIJ-IONSKA

Nazivni napon: 20 V (istosmjerna struja)

Kapacitet: 2 Ah

Broj ćelija: 5

Brzi punjač baterija: PLG 20 A1*

ULAZ / Input:

Nazivni napon: 230 - 240 V

~

, 50 Hz

(izmjenična struja)

Nazivna snaga: 65 W

Osigurač (unutarnji): 3,15 A

T3.15A

IZLAZ / Output:

Nazivni napon: 21,5 V

(istosmjerna struja)

Nazivna struja: 2,4 A

Trajanje punjenja: cca 60 min

Razred zaštite: II / (dvostruka izolacija)

* BATERIJA I UREĐAJ ZA PUNJENJE

NISU UKLJUČENI U OPSEG ISPORUKE

PSBSA 20-Li B2

HR │ 15 ■

Vrijednost emisije buke:

Mjerna vrijednost buke izmjerena je sukladno

EN 62841. Procijenjena A razina emisije buke

električnog alata tipično iznosi:

Razina zvučnog tlaka: L

PA

= 86,7 dB (A)

Odstupanje K: K

PA

= 3 dB

Razina zvučnog učinka: L

WA

= 97,7 dB (A)

Odstupanje K: K

WA

= 3 dB

Vrijednost emisije vibracija:

Ukupne vrijednosti vibracija (zbroj vektora triju

smjerova) izračunate su u skladu s normom

EN 62841:

Udarno bušenje u betonu:

a

H,ID

= 9,875 m/s

2

Bušenje u metalu:

a

h,D

= 3,475 m/s

2

Odstupanje K = 1,5 m/s

2

Vijci:

<2,5 m/s

2

Odstupanje K = 1,5 m/s

2

Nosite zaštitu sluha!

NAPOMENA

► Navedene ukupne vrijednosti vibracija i na-

vedene vrijednosti emisije buke izmjerene su

standardiziranom metodom ispitivanja i mogu

se koristiti za usporedbu električnih alata.

► Navedene ukupne vrijednosti vibracija i nave-

dene vrijednosti emisije buke mogu se koristiti

i za uvodnu procjenu opterećenja.

UPOZORENJE!

► Emisije vibracija i buke mogu tijekom stvarnog

korištenja električnog alata odstupati od navede-

nih vrijednosti ovisno o načinu uporabe električ-

nog alata, a posebno ovisno o vrsti izratka.

► Pokušajte opterećenje zadržati na što nižoj

razini. Primjeri mjera za smanjenje opterećenja

vibracijama su nošenje rukavica prilikom upo

-

rabe uređaja i ograničenje radnog vremena.

Pritom morate uzeti u obzir sve dijelove ciklusa

pogona (primjerice razdoblja u kojima je elek-

trični uređaji isključen, kao i razdoblja u kojima

je uređaj uključen ali radi bez opterećenja).

Opće sigurnosne

napomene za uporabu

električnog alata

UPOZORENJE!

► Pročitajte sve sigurnosne napomene, upute,

slike i tehničke podatke koji se nalaze uz

ovaj električni alat. Nepridržavanje sljedećih

uputa može uzrokovati strujni udar, požar i/ili

teške ozljede.

Sačuvajte sve sigurnosne napomene i upute

za buduću uporabu.

Pojam „električni alat“ koji se koristi u sigurnosnim

napomenama odnosi se na električni alat s mrežnim

napajanjem (s mrežnim kabelom) i na električni

alat s pogonom na baterije (bez mrežnog kabela).

1. Sigurnost na radnom mjestu

a) Radno mjesto držite čistim i dobro osvijetlje-

nim. Neuredno i neosvijetljeno radno mjesto

može uzrokovati nezgode.

b) Električni alat ne koristite u eksplozivnom

okruženju u kojem se nalaze zapaljive tekući-

ne, plinovi ili prašina. Električni uređaji stvaraju

iskre koje mogu zapaliti prašinu ili pare.

c) Djecu i druge osobe držite podalje tijekom

korištenja električnog alata. U slučaju nepažnje

možete izgubiti kontrolu nad električnim alatom.

2. Električna sigurnost

a) Priključni utikač električnog alata mora prista-

jati u utičnicu. Utikač se ni na koji način ne

smije mijenjati.

Ne koristite adapterske utikače s uzemljenim

električnim alatom. Neizmijenjeni utikači i

odgovarajuće utičnice umanjuju rizik od strujnog

udara.

b) Izbjegavajte tjelesni kontakt s uzemljenim

površinama kao što su cijevi, sustavi grijanja,

štednjaci ili hladnjaci. Rizik od strujnog udara

veći je kada je tijelo uzemljeno.

c) Električni alat zaštitite od kiše i vlage. Prodi-

ranje vode u električni uređaj povećava rizik

od strujnog udara.

Pagina se încarcă ...

Parkside PSBSA 20-LI B2 Instrucțiuni de utilizare

Acest manual este potrivit și pentru

Parkside PSBSA 20-LI B2 Instrucțiuni de utilizare

Lucrări conexe

Alte documente