Yamaha MDX-596 Manualul proprietarului

MDX-596

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

BG

Minidisc Recorder

Lecteur Enregistreur de Minidisc

E-2

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. This unit is a sophisticated mini disc recorder. To ensure

proper operation for the best possible performance, please

read this manual carefully.

2. Install your unit in a cool, dry, clean place with good

ventilation. Avoid placing it in direct sunlight, near

sources of heat, or in locations subject to vibration,

excessive dust, heat, cold, or moisture. To avoid humming

sounds, position the unit away from other electrical

appliances, motors, and transformers.

3. Do not operate the unit upside-down. It may overheat,

possibly causing damage.

4. Do not place another component on top of this unit, to do

so may discolor or damage the surface of the unit.

5. Do not open the cabinet of this unit, to do so may result in

damage to the unit or electrical shock. If any foreign object

or substance gets into the unit, contact your dealer for

assistance.

6. When removing the power plug from the wall outlet,

always pull directly on the plug; never pull the cord itself.

7. Do not apply excessive force when operating switches and

knobs.

8. When moving the unit, be sure to first disconnect the

power cord from the AC outlet and disconnect all cords

connecting the unit to other equipment.

9. To prevent damage by lightning, disconnect the power

cord from the wall outlet during an electrical storm.

10. Do not attempt to clean this unit with chemical solvents as

this may damage the finish. Use a clean, dry cloth.

11. Be sure to read the “TROUBLESHOOTING” section for

advice on common operating errors before concluding that

your unit is faulty.

12. Keep this manual in a safe place for future reference.

13. The voltage to be used must be the same as that specified

on this unit. Using this unit with a higher voltage than that

which is specified is dangerous and may result in a fire or

other type of accident causing damage. YAMAHA will not

be held responsible for any damage resulting from use of

this unit with a voltage other than that which is specified.

Note

Please check the copyright laws in your country to record

from records, compact discs, radio, etc. Recording of

copyright material may infringe copyright laws.

This mini disc recorder is

classified as a CLASS 1

LASER product.

The CLASS 1 LASER

PRODUCT label is located

on the rear exterior.

(U.K., Europe and general

models only)

For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off

and an appropriate 3 pin plug fitted. For details, refer to

the instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is

hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows: The wire which is coloured

BLUE must be connected to the terminal which is

marked with the letter N or coloured BLACK. The

wire which is coloured BROWN must be connected

to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the

earth terminal of the three pin plug.

CAUTION FOR CARRYING THE UNIT

Before carrying the unit, first remove a disc from the unit,

press POWER to turn the unit off, then disconnect the AC

power plug from the wall outlet.

WARNING

To reduce the risk of fire or electric shock, do not expose this

appliance to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

DANGER

Invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

Voltage Selector <General model only>

The voltage selector on the rear panel of this unit must

be set for your local main voltage BEFORE plugging

into the AC power supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

E-3

English

CONTENTS

Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For

the best performance, read this manual carefully. It will guide you in operating your YAMAHA product.

¶ MINI DISC Digital Audio System

¶ Digital Optical Input (2)/Output

¶ Sampling Rate Converter

¶ Repeat Function

¶ EDIT Function

¶ Synchronized Recording

INTRODUCTION

FEATURES

¶ Time Rescue Record Function

¶ Monaural Recording

¶ Fade-in and Fade-out Functions

¶ Timer Playback and Recording

US and foreign patents licensed from Dolby

Laboratories Licensing Corporation.

PART DESCRIPTIONS.......................................... 4

FRONT PANEL.............................................................. 4

REMOTE CONTROL .................................................... 5

Remote Control Operation Range .............................. 5

Battery Installation...................................................... 5

CONNECTIONS ..................................................... 6

ANALOG CONNECTIONS .......................................... 6

DIGITAL CONNECTIONS........................................... 6

PLAYBACK............................................................ 7

Skipping Tracks .......................................................... 7

Searching ..................................................................... 7

Switching the Display................................................. 8

RANDOM PLAY ........................................................... 9

REPEAT PLAY .............................................................. 9

Single Track Repeat / Full Disc Repeat ..................... 9

Part (A-B) Repeat ..................................................... 10

PROGRAM PLAY ....................................................... 10

Using Headphones for Private Listening ................. 11

RECORDING........................................................ 12

Adjusting Recording Levels ..................................... 13

Auto Marking ............................................................ 14

Using the Fade-in and Fade-out Functions .............. 14

TIME RESCUE RECORDING.................................... 15

SYNCHRO RECORDING ........................................... 15

MONAURAL RECORDING....................................... 16

MONITOR OUT........................................................... 16

PROTECTING A RECORDED MD ........................... 16

EDITING ............................................................... 17

ERASE .......................................................................... 17

Disc Erase.................................................................. 17

Track Erase................................................................ 18

Part Erase .................................................................. 18

Disc or Track Title Erase.......................................... 19

MOVE ........................................................................... 19

COMBINE .................................................................... 20

DIVIDE ......................................................................... 20

UNDO ........................................................................... 21

DISC MAINTENANCE ............................................... 21

TOC WRITE ............................................................. 21

FRA CHECK............................................................. 21

TITLING................................................................ 22

TIMER OPERATIONS ......................................... 23

Timer Recording ....................................................... 23

Timer Playback ......................................................... 23

MD SYSTEM LIMITATIONS................................ 24

DISPLAY MESSAGES ........................................ 25

COPY PROTECTION (SCMS) ............................ 25

TROUBLESHOOTING......................................... 26

SPECIFICATIONS ............................................... 27

E-4

FRONT PANEL

~ POWER (P.7)

Ÿ Disc insertion slot (P.7)

! ) EJECT (P.7)

⁄ Remote control sensor (P.5)

@ Display

¤ #/* (P.7)

# & (P.7/P.13/P.17/P.22)

‹ REC (P.12~P.16)

$ TIMER (P.23)

› RANDOM (P.9)

% S/F – REPEAT (P.9)

ﬁ A-B – REPEAT (P.10)

^ DISPLAY (P.8)

PART DESCRIPTIONS

ﬂ SCROLL (P.8)

& TITLE (P.22)

‡ CHARA. (P.22)

* DELETE/CANCEL (P.17/P.22)

° EDIT (P.17~P.21)

( SET/ENTER (P.17~P.21)

· Jog dial ($ ›)/DIGITAL REC LEVEL

(P.7/P.13/P.18~P.20/P.22)

) SEARCH ! ⁄ (P.7/P.22)

‚ INPUT (P.12)

_ ANALOG REC LEVEL (P.13)

— PHONES (P.11)

PHONES jack

PHONES LEVEL knob

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–

TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

E-5

English

30°

REMOTE CONTROL

~ REPEAT (P.9/P.10)

S/F [ ! ]

A-B [ ? ]

Ÿ PROG [ – ] (P.10/P.11)

! RNDM [ & ] (P.9)

⁄ Numbers [Characters]

(P.7/P.22)

@ CHAR. (P.22)

¤ TITLE (P.22)

# SEARCH ! ⁄

(P.7/P.22)

‹ SKIP $ › (P.7/P.22)

$ PLAY # (P.7/P.13)

› PAUSE * (P.7/P.13)

% DISPLAY (P.8)

Remote Control Operation Range

Notes

• There should be no large obstacles between the remote

control and the remote sensor on the main unit.

• Strong light (especially from an inverter type fluorescent

lamp) shining directly on the remote sensor may prevent

proper operation. In such cases, reposition the main unit to

avoid direct light.

Battery Installation

Battery replacement

When you notice a decrease in the operating range of

the remote control, replace both batteries with new ones.

Notes

• Use only AA, R6, UM-3 batteries for replacement.

• Be sure to insert the batteries with correct polarity (as

illustrated on the battery compartment).

• Remove the batteries if the remote control will not be used

for an extended period of time.

• If batteries leak, dispose of them immediately. Avoid

touching the leaking material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

6 m

ﬁ SCROLL (P.8)

^ NUMBER (P.22)

ﬂ DELETE (P.22)

& SET (P.22)

‡ M-MARK (P.14)

* INPUT (P.12)

° MONO/ST (P.16)

( Special Record buttons

TIME (P.15)

SYNC (P.15)

· CD-P (P.15)

) REC ? (P.12~P.16)

‚ STOP & (P.7/P.13/P.22)

?

A–B

!

S/F

SCROLLDISPLAY

REPEAT

–

PROG

&

RNDM

)(

D E F

2

A B C

1

M N O

5

J K L

4

G H I

3

S T U

7

P Q R

6

/

0

Y Z

9

V W X

8

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

M-MARK MONO/ST

SKIP

PAUSEPLAY RECSTOP

SPACE

+10

MDX

CD-P

SYNCTIME

REC

E-6

PLAY

REC

DIGITAL

OPTICAL

OUT

(PLAY)

1

2

ANALOG

IN

(REC)

OUT

(PLAY)

IN

(REC)

DIGITAL OUT

OPTICAL

DIGITAL IN DIGITAL OUT

OPTICAL OPTICAL

DIGITAL

OPTICAL

OUT

(PLAY)

1

2

IN

(REC)

ANALOG

IN

(REC)

OUT

(PLAY)

CONNECTIONS

Do not plug in this unit (or other components) until all connections are complete.

• Connections should be made to the correct input/output terminals on the other component.

• Also refer to the owner’s manual supplied with the component you are connecting.

• If the placement of this unit causes noise in other equipment, such as a tuner, move them farther apart.

ANALOG CONNECTIONS

Notes for analog connections

• The white plug on the audio connecting cords corresponds to the L (left) channel and the red plug corresponds to the R (right)

channel. Be sure to connect L (left) to L and R (right) to R. Also make sure that the plugs are fully inserted and that the

connection is firm.

• The ANALOG OUT jacks on the MD recorder should be connected to the MD PLAY jacks on your amplifier.

The ANALOG IN jacks on the MD recorder should be connected to the MD REC jacks on your amplifier.

• The ANALOG OUT terminals on this unit are numbered 3 and the ANALOG IN jacks are numbered 4. When connecting this

unit to a YAMAHA amplifier or receiver whose terminals are numbered 1, 2 , 3, 4 ... (etc.), connect this unit’s ANALOG

OUT terminals to the input terminals numbered 3 and connect this unit’s ANALOG IN terminals to the output terminals

numbered 4 on the rear panel of the amplifier or receiver.

Notes for digital connections

• The DIGITAL IN terminals can be connected to any component with an optical output so you can make direct digital recordings.

• The DIGITAL OUT terminal can be connected to a any component with an optical input so you can output digital audio from an

MD.

• Before making OPTICAL connections, remove the terminal cover(s).

• In order to protect the terminals from dust, be sure to attach the terminal covers when the optical terminals are not being used.

Audio connecting cords (included)

To AC outlet

Amplifier/Receiver

To AC outlet

*Optical fiber cable

Amplifier/Receiver

(or MD/DAT recorder)

with optical IN/OUT

Optical fiber cable (included)

CD player (etc.) with

optical OUT

* One optical fiber cable is included with

the MDX-596. Additional OPTICAL

connections should be made using

commercially available optical fiber

cables.

DIGITAL CONNECTIONS

E-7

English

NATURAL SOUND MINIDISC RECORDER MDX–596

PLAYBACK

Preparations

• Be sure to set the TIMER switch to OFF, then press

POWER to turn this unit on.

• Set your amplifier or receiver to MD.

To stop

Press & (STOP & on the remote).

To eject the MD

Press ) EJECT.

Note

The MONO indicator lights when playing monaural MDs.

Skipping Tracks

To skip to the next track

Turn the jog dial to the right (or press SKIP › on the

remote).

To skip to a previous track

Turn the jog dial to the left (or press SKIP $ on the

remote).

Turn one click to skip to the beginning of the current

track. Turn an additional click to skip back to the

beginning of each previous track.

To skip to a specific track number

Press the number buttons on the remote corresponding

to the track you desire.

Example:

To select track 3, press 3.

To select track 13, press +10, then press 3.

To select track 23, press +10 twice, then press 3.

To skip to the last track on the disc

Turn the jog dial to the left when the display is showing

the total tracks and total playing time.

Searching

To search forward during play or pause

Press and hold SEARCH ⁄.

To search in reverse during play or pause

Press and hold SEARCH !.

Notes

• Sound can be heard when searching in play mode to help

you locate the desired position within the track. No sound

is heard when searching in pause mode, but the search is

conducted at a higher speed.

• Search may not function correctly when there are several

consecutive tracks consisting of only a few seconds each.

21

Jog dial

1 Insert an MD.

2 Press # /* (PLAY # on the remote) to start

playback.

3 Adjust the volume using the volume control

on your amplifier or receiver.

To pause

Press #/* (PAUSE * on the remote).

Press again to resume playback (or press PLAY # on

the remote).

Arrow pointed toward

disc insertion slot

Label facing up

&

?

A–B

!

S/F

SCROLLDISPLAY

REPEAT

–

PROG

&

RNDM

)(

D E F

2

A B C

1

M N O

5

J K L

4

G H I

3

S T U

7

P Q R

6

/

0

Y Z

9

V W X

8

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

SPACE

+10

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

) EJECT

SEARCH ! ⁄

SEARCH

! ⁄

2

SKIP

$ ›

PAUSE *

Numbers

STOP &

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+



–

TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

E-8

During playback

Press DISPLAY repeatedly to display the following

information.

1 Current track number and elapsed time

2 Time remaining on the current track

3 Track title

If the track has not been given a name, “No Title” is

displayed.

To view the entire disc (track) title

If the disc (track) title is too long to fit in the display,

press SCROLL to move the title sequentially across the

display. While the title is being displayed, press

SCROLL to pause the display, and again to continue

presentation of the title. Press and hold SCROLL for

rapid presentation of the title.

Switching the Display

When you insert an MD, the disc title is displayed

automatically.

Press DISPLAY during stop or playback to display

other information, such as the remaining time and track

titles.

During stop

Press DISPLAY repeatedly to display the following

information.

1 Number of tracks and total playing time

2 Time remaining on the MD (only for recordable

MDs)

3 Disc title

If the disc has not been given a name, “No Title” is

displayed.

SCROLL

DISPLAY

Total tracks Total playing time

REMAIN indicator Time remaining on the MD

Total tracks

REMAIN indicator

Track number

Elapsed time

DISC TRACK

TOTAL

REMAIN

DISC TRACK

TOTAL

REMAIN

DISC TRACK

TOTAL

REMAIN

DISC TRACK

TOTAL

REMAIN

DISC TRACK

TOTAL

REMAIN

DISC TRACK

TOTAL

REMAIN

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–



TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

?

A–B

!

S/F

SCROLLDISPLAY

REPEAT

–

PROG

&

RNDM

)(

D E F

2

A B C

1

M N O

5

J K L

4

G H I

3

S T U

7

P Q R

6

/

0

Y Z

9

V W X

8

SPACE

+10

SCROLLDISPLAY

E-9

English

RANDOM PLAY

You can have the unit play all the tracks on a disc in

random order.

To start random playback

Press RANDOM (RNDM on the remote).

The RANDOM indicator lights up and “_ _ _ – – : – –”

appears in the display while the unit selects a track.

Playback starts automatically.

To cancel

Press & (STOP & on the remote) to stop playback. The

RANDOM indicator turns off and random playback is

canceled.

Note

Pressing SKIP › during random play skips to another track

at random. Pressing SKIP $ returns to the beginning of the

current track (you cannot return to previously played tracks).

S/F – REPEAT A-B – REPEAT

RANDOM

REPEAT

A-BSF

REPEAT

A-BSF

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–



TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

?

A–B

!

S/F

SCROLLDISPLAY

REPEAT

–

PROG

&

RNDM

)(

D E F

2

A B C

1

M N O

5

J K L

4

G H I

3

S T U

7

P Q R

6

/

0

Y Z

9

V W X

8

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

SPACE

+10

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

RNDM

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–

TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

?

A–B

!

S/F

SCROLLDISPLAY

REPEAT

–

PROG

&

RNDM

)(

D E F

2

A B C

1

M N O

5

J K L

4

G H I

3

S T U

7

P Q R

6

/

0

Y Z

9

V W X

8

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

SPACE

+10

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

S/F –

REPEAT

A-B –

REPEAT

&

SKIP

$ ›

STOP &

&

STOP &

REPEAT PLAY

You can have the unit repeat a single track, a full disc,

or just part of a track.

Single Track Repeat / Full Disc Repeat

Press S/F – REPEAT repeatedly to light the

REPEAT S or REPEAT F indicators.

To repeat the single track, light the REPEAT S

indicators.

To repeat the full disc, light the REPEAT F indicators.

To cancel

Press S/F – REPEAT repeatedly to turn off the

REPEAT S or REPEAT F indicators.

Notes on Full Disc Repeat

• In program play mode, the entire program is played

repeatedly.

• In random play mode, the unit reshuffles the tracks and

plays them again after each track plays once.

$ ›

E-10

PROGRAM PLAY

This function lets you enjoy listening to your favorite

tracks in any order you desire.

1 Press STOP & to stop playback.

2 Press PROG to light up the PROGRAM

indicator.

3 Program the desired track by pressing the

corresponding number buttons.

Example:

To select track 3, press 3.

To select track 13, press +10, then press 3.

To select track 23, press +10 twice, then press 3.

The following display appears momentarily to show

the step information:

The display then switches to the program status:

4 Repeat step 3 to program up to 30 steps.

5 Press PLAY # to start program playback.

?

A–B

!

S/F

SCROLLDISPLAY

REPEAT

–

PROG

&

RNDM

)(

D E F

2

A B C

1

M N O

5

J K L

4

G H I

3

S T U

7

P Q R

6

/

0

Y Z

9

V W X

8

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

SPACE

+10

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

4

2

1

3

DELETE

SEARCH

! ⁄

SKIP

$ ›

Programmed

track number Total playing time

Step number

PROGRAM

TRACK

TOTAL

PROGRAM

Part (A-B) Repeat

This function lets you repeat a specific part of a track.

It’s a convenient way to study a language, or to learn the

lyrics to your favorite song (etc.).

1 Press A-B – REPEAT during playback to

specify the beginning (A point) of the part you

want to repeat.

The REPEAT A indicators light up.

2 Press A-B – REPEAT again to specify the

end (B point) of the part you want to repeat.

The REPEAT A-B indicators light up and the part

you specified starts to repeat.

To cancel

Press & or A-B – REPEAT.

REPEAT

A-BSF

REPEAT

A-BSF

PAUSE *

E-11

English

To check the programmed data

1 Press STOP & or PAUSE * to stop or pause

program playback.

2 Press SKIP $ or › to skip through the step

information (or use the jog dial on the front panel).

To add a step

1 Press STOP & to stop program playback.

2 Press PROG to enter the program input mode.

3 Press SKIP › repeatedly until “_” is displayed.

4 Use the number buttons to program a new track at

the end of the program.

To delete a specific step

1 Press STOP & to stop program playback.

2 Press PROG to enter the program input mode.

3 Press SKIP $ or › to skip through the step

information (or use the jog dial on the front panel).

4 Press DELETE (or DELETE/CANCEL on the

front panel) to delete the step. The higher steps are

renumbered automatically.

To change a step

1 Press STOP & to stop program playback.

2 Press PROG to enter the program input mode.

3 Press SKIP $ or › to skip through the step

information (or use the jog dial on the front panel).

4 Use the number buttons to program a new track

number for that step. The original track is cleared

from memory and the new track is programmed.

To cancel

Press STOP & in the stop mode or the program input

mode to turn off the PROGRAM indicator. The program

is erased.

Notes

• If the total time exceeds 255 minutes, “255mOver” is

displayed instead of the total time.

• SKIP $ or › can be used during playback to skip

between programmed tracks.

• SEARCH ⁄ can be used during playback to search

through all tracks in the current program.

• SEARCH ! can be used during playback to return to

the beginning of the current track.

Using Headphones for Private

Listening

Set the PHONES LEVEL knob on the front panel to

“0” (minimum) and insert the headphones plug of your

stereo headphones into the PHONES jack.

To adjust the volume level of the headphones

Use the PHONES LEVEL knob.

Turn toward “10” (maximum) to increase the volume.

Turn toward “0” (minimum) to decrease the volume.

E-12

2 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

For Select

LINE IN 4 ANALOG

DIGITAL IN OPTICAL 1 DIGITAL OPT. 1

DIGITAL IN OPTICAL 2 DIGITAL OPT. 2

* Appears when digital signal is input.

3 Locate the point where you want to start

recording.

• When recording on a blank MD

Skip this step.

• To start recording from the end of a previous

recording

Press & to set this unit to stop mode.

• To record over a previous recording

Turn the jog dial (or press SKIP $ or › on the

remote) to select a track (recording starts from the

beginning of the deleted track), or press #/* (PAUSE

* on the remote) during playback to pause at the point

where you want to start recording.

4 Press REC (REC ‡ on the remote) to set this

unit to record pause mode.

The REC * indicators light up.

“REC Standby” and the amount of time available for

recording flash alternately in the display.

If you selected a track number or paused

playback (in step 3) to record over a previous

recording

“OverWrite OK?” appears in the display.

To confirm, press ENTER. This operation will erase the

selected track number (or point) and all subsequent

material.

To cancel, press CANCEL (or &).

Adjust the recording level corresponding to the

audio input you selected in step 2. Refer to

“Adjusting Recording Levels” on page 13 for

more details.

Note

When recording from a digital source that has a digital

output (volume) control, set the output level (volume) to

“MAX”. Recording may not be possible at low output

levels (when the digital volume is turned down).

1 Insert an MD.

RECORDING

This unit allows you to make recordings from a wide

variety of program sources (both analog and digital).

When recording an analog source (such as an FM

broadcast or cassette) this unit converts the analog

signals to a 44.1 kHz digital signal before recording

them onto the MD.

When recording a digital source, this unit converts the

digital signals to 44.1 kHz for recording onto the MD.

However, if you are recording a 44.1 kHz source signal

(such as a CD) there is no conversion. This unit can

record 32, 44.1 and 48 kHz digital signals.

Preparations

• Be sure to set the TIMER switch to OFF, then press

POWER to turn this unit on.

• Set your amplifier or receiver to the program source

to be recorded.

Input indicator

(Source) sampling frequency indicators*

Arrow pointed toward

disc insertion slot

Label facing up

ANALOG

DIGITAL

OPT. 1 2

COAX.

3244.148

kHz

REPEAT

DISC TRACK

TOTAL

REMAIN

RANDOM

PROGRAM

A-BSF

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–



TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

1

) EJECT

2

REC LEVEL

45

2

4

M-MARK

STOP &

5

&

PAUSE *

NATURAL SOUND MINIDISC RECORDER MDX–596

ENTER

E-13

English

5 Press #/* (PLAY # on the remote) to start

recording.

The TOC indicator lights up.

When the TOC indicator is lit, this means that the TOC

information has not yet been written to the disc. After

recording is complete, the TOC data is automatically

written to the disc.

6 Start playing the program source to be

recorded.

To pause

Press #/* (PAUSE * on the remote).

Press again to resume recording.

To stop

Press & (STOP & on the remote).

To eject the MD

Press ) EJECT.

Should not light

Adjusting Recording Levels

Setting the digital volume level

The volume level of digital audio sources is often

similar, however, level differences may be quite obvious

between different digital audio formats and even

between one recording and another. To maintain a

consistent volume level in MD recordings, it is possible

to change the volume of the input digital signal.

To select the digital signal to be recorded or monitored,

press INPUT repeatedly until the appropriate digital

input indicator (DIGITAL OPT. 1 or DIGITAL OPT. 2)

appears in the display. During record or record pause

mode, turning DIGITAL REC LEVEL adjusts the

volume of the digital signal. The digital volume can be

adjusted up to +12 dB and down to a minimum (MIN)

level from the default volume of 0 dB, the level of the

input digital signal. To set the volume level, play the

digital source to be recorded and adjust DIGITAL REC

LEVEL so that the highest peak causes the 0 dB level

indicators to flicker. The OVER indicators should not

light.

Even when recording is stopped, the digital recording

level is maintained in memory.

Notes

• When DIGITAL REC LEVEL is turned, the digital

volume level is adjusted in 0.5 dB steps between +12 dB

and –20 dB, 1 dB steps from –20 dB to –30 dB, 2 dB steps

from –30 dB to –40 dB, followed by –44 dB, –48 dB,

–54 dB, –62 dB and MIN.

• Although some sources can be recorded with lower peak

levels, setting the peak levels too low may degrade the

quality of the recording.

• The digital volume cannot be adjusted while a track title is

being entered.

• The digital recording levels are maintained independently

for DIGITAL OPT. 1 and DIGITAL OPT. 2.

Setting the analog recording level

Press INPUT repeatedly until the ANALOG indicator

appears in the display, and press REC (REC ‡ on the

remote) to put this unit in the record pause or monitor

out mode. For best results, play the loudest passage of

the source to be recorded and watch the recording level

meter in the display. Adjust ANALOG REC LEVEL so

that the highest peak causes the 0 dB level indicators to

flicker. The OVER segment should not light.

L

R

dB

–

60 30 10 6 4 2 1 0 OVER00

––– – ––

E-14

Auto Marking

When making a recording, you can choose either

automatic or manual marking. This feature operates

somewhat differently for analog and digital signals. See

below for details.

Press M-MARK on the remote repeatedly to select

automatic (MANUAL indicator out) or manual

(MANUAL indicator lit) marking.

When recording analog signals

Auto : Track numbers are written in synchronization

with the input level of the signal being recorded. During

recording, if no sound is detected for more than 1.5

seconds, the recorder interprets this to be a gap between

two tracks. When the source signal is detected again, a

track number is automatically written.

Manual : One track number is written automatically

when you start recording, but none are written during

recording. To mark a track number, press M-MARK at

the desired position while recording.

Note

When using manual marking, the marks must be set at least 4

seconds apart.

When recording digital signals

Track numbers are written in the same positions as the

original source (CD, etc.) with either automatic or manual

marking.

To add additional track numbers, set M-MARK to

MANUAL and press M-MARK at the desired position

while recording.

Notes

• When recording is paused, the portion recorded up to the

pause is counted as an individual track. When recording is

resumed, a new track number is created.

• During synchronized recording, manual track marking is

not possible.

MANUAL

Using the Fade-in and Fade-out

Functions

When making recordings, it is possible to fade-in at the

beginning of a recording and fade-out at the end of a

recording. This function is useful for custom recording

of songs and other material.

Fading in to a recording

Press REC (REC ‡ on the remote) in step 5 of the

recording procedure described on pages 12 and 13.

“Fade in” is displayed and recording begins with a 10 second

fade-in. (During the fade-in, the volume of the source being

recorded is gradually increased to the set recording level.)

Fading out of a recording

Press REC (REC ‡ on the remote) while making

a recording.

“Fade out” is displayed and a 10 second fade-out is performed.

Following the fade-out, this unit is set to the record pause

mode. (During the fade-out, the volume of the source being

recorded is gradually decreased to the minimum level.)

E-15

English

SYNCHRO RECORDING

The synchronized recording function lets you set this

unit to start recording automatically when a sound signal

is input. When operating this unit in combination with a

remote controllable Yamaha CD player, you can use the

CD-P button on this unit’s remote control to start

playback from the CD player.

1 Load the sound source into the source

component.

If necessary, program, or select the track you want

to start recording from before proceeding to the

next step. (Refer to the operation manual supplied

with the source component for instructions

regarding its use.)

2 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

3 Locate the point where you want to start

recording.

4 Press SYNC to set this unit to record pause

mode.

The REC * indicators light up.

“Synchro REC” and the amount of time available for

recording flash alternately in the display.

During synchronized recording, input sources are recorded

at the current ANALOG and DIGITAL REC LEVEL

setting.

5 Start playing the sound source. (Press CD-P if

recording from a Yamaha CD player.)

The MD starts recording automatically when a sound

signal is input. When the sound signal stops, the unit

switches back to record pause mode and “Synchro REC”

blinks in the display.

6 To continue recording, repeat step 5.

When you have finished recording, press & on

this unit to cancel the record pause mode.

Note

When the signals at the beginning of a track are lower than the

level required to start synchronized recording, they are not

recorded. Should this occur, perform manual recording.

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

4

5

2

TIME RESCUE RECORDING

The Time Rescue (TIME) recording function allows you

to start recording six seconds before you press record.

During record pause mode, the MD recorder monitors

the input signal and continuously maintains a six second

memory “cache”. Therefore, you can record a song that

just started without cutting off the beginning. You may

find this function useful when recording live broadcasts,

or when you want to start recording from the beginning

of a song without recording lots of commercials (etc.).

1 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

2 Locate the point where you want to start

recording.

3 Press REC ‡ to set this unit to record pause

mode.

The REC * indicators light up.

“REC Standby” and the amount of time available for

recording flash alternately in the display.

To adjust the recording level of digital or analog input

sources, see “Adjusting Recording Levels” on page 13.

4 Press TIME to start recording when you hear

the beginning of a song you want to record.

Recording starts from the memory cache, allowing you to

record from a point approximately six seconds before you

pressed TIME.

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

1

3

4

E-16

MONITOR OUT

When a disc is not loaded, you can use the monitor out

function to monitor the sound of the input source. This

allows you to enjoy better sound from your other digital

source components, such as CD, by using this unit as a

digital to analog converter.

1 Press ) EJECT to remove the disc.

2 Press INPUT repeatedly to select the input

connected to the sound source you want to

monitor.

3 Press REC.

“MONITOR OUT” appears in the display.

Sound from the selected input will be output from this

unit’s analog and digital output terminals.

4 Start playing the sound source selected in step

2.

The sound is output from the MD recorder’s analog and

digital output terminals.

To cancel

Press REC again, press &, or insert a disc.

Note

The digital volume can be adjusted when using the monitor out

function.

PROTECTING A RECORDED MD

Tab

Slide the tab to

open the slot.

• To protect a recorded MD, slide the tab on the side of

the MD to open the slot.

In this position, the MD cannot be used for recording,

editing, or titling. To record, edit, or title the MD,

slide the tab to close the slot.

• If the MD is protected against erasure, “Protected”

appears in the display.

13

2

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–



TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

MONAURAL RECORDING

Recording in monaural (mono) allows you to record up

to 148 minutes of sound on one 74 minute MD. (When

recording in stereo you can record up to 74 minutes of

sound.) This may be useful when recording an

interview, debate, or whenever you want to record for a

long time on one disc.

Press MONO/ST to light the MONO indicator

after step 3 of the recording procedure described

on pages 12 and 13.

CHAR.TITLE SETDELETENUMBER

SEARCH INPUT

SKIP

PAUSEPLAY RECSTOP

MDX

CD-P

REC

SYNCTIME

M-MARK MONO/ST

3

4

5

1

E-17

English

EDITING

One of the main advantages of MD is its editing

capabilities. You can remove the commercials from a

radio broadcast, reorder songs into the order you want,

remove songs, combine songs, and even remove part of

a song.

This unit offers the following editing operations.

(Please note that track numbers are updated

automatically when you perform a ERASE, MOVE,

COMBINE or DIVIDE operation.)

¶ ERASE (P.17~P.19)

Lets you erase a track, the entire disc, or part of a

track. You can also erase the title of a disc, or the

titles of tracks on a disc.

¶ MOVE (P.19)

Lets you move a track to a different track number.

¶ COMBINE (P.20)

Lets you combine two adjacent tracks.

¶ DIVIDE (P.20)

Lets you split a single track into two different

tracks.

¶ TOC WRITE (P.21)

Lets you write TOC information to the disc so that

changes are saved.

¶ FRA CHECK (P.21)

Lets you recover disc space that may have been lost

after multiple edit operations.

¶ UNDO (P.21)

Lets you undo the previous edit operation if you

make a mistake (you cannot, however, undo the

UNDO function).

Notes on editing

• To cancel an edit

Press CANCEL (or &).

• Before editing

Make sure that the MD is not protected against erasure. If

the MD is protected, you cannot edit the MD. Slide the tab

to close the slot on the side of the MD.

• After editing

Update the TOC information by pressing ) EJECT or

using TOC WRITE function.

CANCEL &

REC

EJECT

POWER

0

10

0

10

RANDOM S/F REPEAT A–B DISPLAY SCROLL TITLE CHARA. DELETE EDIT SET

CANCEL ENTER

REC LEVEL PHONES LEVEL

INPUTSEARCH

+

–



TIMER

OFF

PLAYREC

NATURAL SOUND MINIDISC RECORDER MDX–596

ANALOG

DIGITAL

REC LEVEL

ENTER EDIT Jog

dial

#/*!

⁄

ERASE

The ability to erase sound without having to re-record is

a convenient function of MD. You can erase the entire

disc, a single track, or just part of a track.

Disc Erase

This operation lets you erase all audio and title

(character) data to create a blank MD. Please note that

once erased, this data can be recovered using the UNDO

function.

1 Press & to set this unit to stop mode.

2 Press EDIT repeatedly to display “Disc

Erase?”, then press ENTER.

“Disc Erase OK?” appears in the display.

3 Press ENTER again.

When all audio, name and title data has been erased

“Complete” appears momentarily.

Continued on next page

E-18

Part Erase

This operation lets you erase part of a track.

1 Play the track containing the part you want to

erase.

2 Use SEARCH ! or ⁄ to locate the

beginning of the part you want to erase (point

A), then press # /* to pause at that point.

3 Press EDIT repeatedly to display “A–B

Erase?”, then press ENTER.

Point A (from step 2) is registered and “Erase A–_”

appears in the display.

4 Use # /* and SEARCH ⁄ to locate the end

of the part you want to erase (point B).

5 Press ENTER to register point B.

“Check” appears momentarily in the display, and two

second segments of the track immediately before point A

and after point B play repeatedly. “Erase A–B?” appears

in the display.

To adjust points A and B

Pressing EDIT repeatedly displays “+ A Point = ” and

“+ B Point =” alternately. Adjust the selected point by

turning the jog dial in the direction you want to move the

point.

Each point can be adjusted up to 2 seconds (176 steps) in

either direction.

6 Press ENTER again.

The part is erased and “Complete” appears momentarily.

To erase parts spanning more than one track

Use the COMBINE function described next to combine

the tracks into one track before performing this

operation.

Notes

• After part erase, a new track number is automatically

assigned to the section starting after point B.

• Point B cannot be positioned before point A.

Track Erase

This operation lets you erase a single track as well as

corresponding title data. After you erase the track, the

total number of tracks decreases by one and all tracks

following that track are renumbered.

Example: Erasing track 3

1 Turn the jog dial to select the track you want

to erase.

2 Press EDIT repeatedly to display “Erase ?”,

then press ENTER.

“(track number) Erase OK?” appears in the display.

3 Press ENTER again.

The track is erased and “Complete” appears momentarily.

If you plan to erase two or more tracks

To avoid confusion you should always erase from higher track

numbers to lower track numbers. This prevents accidental

renumbering of tracks you plan to erase.

Before

erasing

After

erasing

Before

erasing

After

erasing

1

ACB

23

12

A1 A2 CB

34

Erase

12

AB DEC

3456

12

AB EFD

3456

E-19

English

MOVE

This function lets you change the position of any track.

When you move tracks, all tracks are automatically

renumbered.

Example: Moving track 2 to the track number 4

1 Turn the jog dial to select the track you want

to move.

2 Press EDIT repeatedly to display “Move ?”,

then press ENTER.

3 Turn the jog dial to select the track’s

destination (new track number).

4 Press ENTER.

“Complete” appears momentarily in the display.

DestinationSelected track

Before

moving

After

moving

12

AB DEC

3456

12

AC BED

3456

ANALOG

DIGITAL

OPT. 1 2

COAX.

DISC TRACK

TOTAL

REMAIN

Disc or Track Title Erase

This operation lets you erase the title of the disc or the

title of tracks on a disc. The title of the disc can only be

erased during the stop mode, however, the title of the

track can be erased during play or stop mode. In the stop

mode, use the jog dial to select the track.

To erase a disc title

1 Press & to set this unit to stop mode.

2 Press EDIT repeatedly to display “Title

Erase?”, then press ENTER.

“Disc Title” and “Erase OK?” appear alternatively in the

display.

3 Press ENTER again.

The disc title is erased and “Complete” appears

momentarily.

To erase a track title

1 Turn the jog dial to select the track with the

title you want to erase.

2 Press EDIT repeatedly to display “Title

Erase?”, then press ENTER.

“Track Title” and “Erase OK?” appear alternatively in the

display.

3 Press ENTER again.

The track title is erased and “Complete” appears

momentarily.

Notes

• Note that the DISC and TRACK indicators appear in the

display when “Title Erase” is displayed to distinguish

between the two operations.

• To avoid mistakes when erasing the disc or track names,

press DISPLAY repeatedly until the title display screen

appears so that titles can be confirmed beforehand.

E-20

Before

combining

12

AB DEC

3456

12

A B+C D E

345

After

combining

COMBINE

This function lets you combine two consecutive tracks

into one. After you combine the tracks, the total number

of tracks decreases by one and the tracks following the

combined tracks are renumbered.

Example: Combining tracks 2 and 3

1 Press & to stop playback.

2 Turn the jog dial to select the second track of

the two you want to combine.

3 Press EDIT repeatedly to display

“Combine ?”, then press ENTER.

“Check” appears momentarily, then the MD recorder plays

the 4 seconds before and after the point where the tracks

will be connected. “(track number) + (track number) OK?”

appears in the display.

4 Press ENTER again.

The tracks are combined and “Complete” appears

momentarily.

Notes

• This operation is not possible when track 1 is selected.

• You can also divide the track later using the DIVIDE

function.

• If “Can’t Edit” appears in the display, the tracks cannot be

combined. This sometimes happens when you have edited

the same track many times. This is due to the technical

limitations of the MD system and is neither a mechanical

error nor a malfunction.

DIVIDE

This function lets you divide one track into two separate

tracks by adding a new track number to a specified point

in the track.

Example: Dividing track 3

1 Play the track you want to divide.

2 Use SEARCH ! or ⁄ to locate the point

where you want to divide the track, then press

#/* to pause at that position.

3 Press EDIT repeatedly to display “Divide ?”,

then press ENTER.

“Check” appears momentarily, then “Divide OK ?”

appears and the MD recorder starts repeating the point

where the track will be divided.

4 If necessary, use the jog dial to adjust the

position of the point where the track will be

divided.

The dividing position can be adjusted up to 2 second (255

steps) in either direction.

5 Press ENTER.

The track is divided and “Complete” appears

momentarily.

Note

You can also combine the tracks later using the COMBINE

function.

12

AB DEC

3456

12

A B C2 DC1

3456

Before

dividing

After

dividing

Pagina se încarcă ...

Yamaha MDX-596 Manualul proprietarului

Yamaha MDX-596 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente