Ubiquiti UniFi UVP Ghid de inițiere rapidă

Marca: Ubiquiti

Model: UniFi UVP

Tip: Ghid de inițiere rapidă

Acest manual este potrivit și pentru

Enterprise VoIP Phone

with 5" Touchscreen

Model: UVP

Introduction

Thank you for purchasing the Ubiquiti Networks

UniFi

VoIP Phone, model UVP. The UniFi VoIP Phone is designed

to integrate easily into a UniFi network. The phone interface

is based on the popular Android

™

platform for ease of use.

This Quick Start Guide is designed to guide you through the

installation, provide an overview of the interface, and also

includes the warrantyterms.

Package Contents

Enterprise VoIP Phone

with 5" Touchscreen

Model: UVP

UniFi VoIP Phone Quick Start Guide

Installation Requirements

• UniFi Switch or PoE (802.3af-compliant) switch

• UniFi Controller

• UniFi Security Gateway

Note: The PBX functionality in the UniFi Security Gateway only

supports the English language. If you need to support other

languages (e.g. for your voicemail), a third-party PBX or SIP/PBX

provider is required.

responsibility to follow local country regulations and indoor cabling requirements.

Before You Begin

Remove the protective covering from the handset.

Remove the protective film from the touchscreen.

Hardware Overview

Front

Touchscreen

LED

Volume

Touchscreen The 5" (diagonal) touchscreen display is used for

all interface navigation and dialing.

Volume Use the volume arrows to adjust audio levels.

LED The LED will illuminate when the device is first connected

to a 48V power source. Once the phone has started up, the

LED will turn off.

IMPORTANT: The LED will flash when a firmware update

is occurring. Do not disconnect power/Ethernet from the

device during this time.

Back Ports

PoE/LAN PC

PoE/LAN

PoE/LAN The PoE/LAN Ethernet port is 802.3at-compliant

and is used to connect data and power to the phone. Connect

this port to the same network as the UniFi Security Gateway

VOIP port.

PC The Ethernet port labeled PC is used for bridging.

WARNING: Do not connect a powered Ethernet

connection to the port labeled PC.

Side Ports

Micro-USB Port The Micro-USB port is only

intended for advanced users connecting the phone

to a computer.

Headset Jack 3.5 mm jack for optional wired stereo

and microphone headsets.

*640-00115-15*

640-00115-15

Handset

Mute button

Mute Press the Mute button to mute the microphone on the

handset.

Hardware Installation

The UniFi VoIP Phone is designed for desktop placement. To

connect the phone, perform the following steps:

1. Connect one end of an Ethernet cable to the wall jack that

is connected to your 48V, 802.3af-compliant switch.

2. Connect the other end of the Ethernet cable to the port

labeled PoE/LAN on the UniFi VoIP Phone.

PoE/LAN PC

Software Configuration

The UniFi VoIP Phone is automatically detected by the UniFi

Controller (4.6.x or above).

Installing the UniFi Controller

If you haven’t already installed the UniFi Controller software,

you can download it at downloads.ubnt.com/unifi

Adopting the Phone in the UniFi Controller

1. Launch the UniFi Controller and go to the Devices tab.

2. Click Adopt.

Navigating the Interface

The Home screen contains a Google

™

search widget, five

default icons at the bottom of the screen, and the three action

baricons.

Google

™

Search Widget

Use the Google

™

search widget to type or speak voice

commands. Touch the bar to bring up a virtual keyboard, or

touch the microphone icon to say a voice command.

Default Home Screen Icons

Icon Description

Phone Displays the keypad to make a call.

Recent calls, contacts, and voicemail are also

accessible from here.

People Press to view a list of contacts.

Apps Press to access the Apps screen. This

default icon is the only one that cannot be be

removed from the Home screen.

Google Play

™

Store Press to open the Google

Play

™

store. Download apps, music, movies,

books, games, and other media. A new or

existing account is required for access.

Google

™

Apps Folder Contains the Google

™

suite of apps including Gmail

™

, YouTube

™

Chrome

™

, Hangouts

™

, Google Drive

™

GoogleMaps

™

, and more.

Action Bar Icons

Icon Description

Back Opens the previous screen you were

working in, even if it was in a different app.

Once you return to the Home screen, you can’t

go back any further.

Home Returns to the Home screen.

Recent Apps Displays a list of recently used

apps. Press an app to open it. To close an app

and remove it from the list, swipe it left or right.

Customizing the Home Screen

Widgets and shortcuts to favorite apps can be placed on the

Home screen. Multiple app shortcuts can also be grouped into

one folder.

Adding App Shortcuts to the Home Screen

To place an app on the Home screen, press the Apps icon on

the Home screen. The Apps screen will be displayed. Press and

hold the icon until it appears on the Home screen. Drag the

icon to the desired location and release it.

Creating Folders on the Home Screen

To create a folder containing multiple app shortcuts, drag an

app shortcut over another app shortcut on the Home screen.

Removing Items from the Home Screen

To remove a widget or app shortcut from the Home screen,

press and hold the item until the Remove text appears at the

top of the screen. Drag the item to the Remove text.

Making a Call

Lift the handset to make a call and the dialer screen will

appear. Use the touchscreen to enter the phone number. Use

the Delete button to correct any mistakes. Press the Call button

to make a call.

JKLGHI

ABC DEF

MNO

TUVPQRS WXYZ

KEYPAD

CONTACTS

2 31

5 64

Call

Delete

Contacts

Call

Call Manager

Volume

Slider

Connected

Number

Connection

Status

Connected Number Displays the extension or phone number

that is being dialed or that is currently connected.

Volume Slider Use the slider to increase or decrease the

volume level.

Connection Status Displays “Dialing” or the total elapsed

time of the currently connected call.

Apps Screen

Pressing the Apps icon brings up the Apps screen. Touch an

app icon to launch an app.

Calculator

Calendar

Gallery

Hangouts

Gmail

Drive

Play Store

People

Downloads

Clock

Play Movies & T

Chrome

Google Settings

Phone

Maps

Play Books

Play Games

Play Music

Play Newsstand

News & Weather

Photos

Google+

Keep

Google

For additional details on using the UniFi VoIP Phone, refer to

the user guide at documentation.ubnt.com

Specifications

UVP

Dimensions 166 x 140 x 182.5 mm (6.50 x 5.50 x 7.19")

Weight 1.10 kg (2.43 lbs)

Display 5" (Diagonal), 640 x 960, 231 ppi

Multi-Touch, Full Color

LED Power: White, glowing

Handset Dynamic Receiver 32 ohm/101 dB/30 mW

Microphone Omnidirectional/-36dB/2.2Kohm

Echo Cancellation DSP removing Ambient Noise

and Acoustic Echo

Power Input PoE 802.3.af (13W)

Hands-Free Speaker Mono 2.6W

Hands-Free

Microphone

Omnidirectional/SNR 61±5 dB/

Sensitivity -38±3dB Analog Silicon Microphone

Connectivity (2) 10/100/1000 Ethernet Ports

(1) USB 2.0 Micro-USB Port

Headset Support 3.5mm Audio Jack

270mW CTIA (LRGM)

Accessory Detection Volume Up/Down and Media Detection

Processor Dual-Core Cortex A9, 1.2 GHz

Storage 4 GB (Shared with Other Applications)

RAM 1 GB

Software

OS Android 4.4, KitKat®

Voice Codec G.722/Speex/iLBC/PCMU/PCMA/GSM

Communication

software

UniFi Phone App

Management

Features

Auto-Provisioning

Protocol SIP/SDP/RTP/RTCP/VLAN/DHCP

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

b. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

c. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

d. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

CAN ICES-3(B)/NMB-3(B)

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

Pagina se încarcă ...

Ubiquiti UniFi UVP Ghid de inițiere rapidă

Marca: Ubiquiti

Model: UniFi UVP

Tip: Ghid de inițiere rapidă

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ubiquiti UniFi UVP Quick start guide
italiano: Ubiquiti UniFi UVP Guida Rapida

Ubiquiti UniFi UVP Ghid de inițiere rapidă

Acest manual este potrivit și pentru

Ubiquiti UniFi UVP Ghid de inițiere rapidă

în alte limbi

Lucrări conexe

Alte documente