Parkside PFBS 160 B2 Manual de utilizare

IAN 281406

PRECISION MULTI-GRINDER PFBS 160 B2

PRECISION MULTI-GRINDER

Translation of the original instructions

MAŞINĂ DE GĂURIT ŞI ŞLEFUIT FIN

Traducerea instrucţiunilor de utilizare original

ΣΥΣΚΕΥΗ ΛΕΙΑΝΣΗΣ ΚΑΙ

ΔΙΑΤΡΗΣΗΣ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

PRECIZNA BUŠILICA-BRUSILICA

Prijevod originalnih uputa za uporabu

FEINBOHRSCHLEIFER

Originalbetriebsanleitung

GB / CY Translation of the original instructions Page 1

HR Prijevod originalnih uputa za uporabu Stranica 19

RO Traducerea instrucţiunilor de utilizare original Pagina 37

GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 55

DE / AT / CH Originalbetriebsanleitung Seite 73

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες

της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

C

A

B

14b

PFBS 160 B2

GB

│

CY

│

1 ■

Contents

Introduction ......................................................2

Intended use ................................................................ 2

Features ................................................................... 2

Package contents ............................................................ 2

Technical data .............................................................. 3

General Power Tool Safety Warnings ................................3

1. Work area safety .......................................................... 3

2. Electrical safety ........................................................... 4

3. Personal safety ............................................................ 4

4. Power tool use and care .................................................... 5

5. Service .................................................................. 5

Safety instructions for all applications ............................................ 5

Additional safety instructions for all applications .................................... 7

Supplementary safety instructions for grinding and abrasive cutting ..................... 8

Supplementary safety instructions for working with wire brushes. . . . . . . . . . . . . . . . . . . . . . . . 8

Safety instructions for LED lights ................................................. 9

General safety instructions for batteries and cells ................................... 9

Original accessories/auxiliary equipment ......................................... 9

Use ............................................................10

Changing/inserting the tool/collet chuck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Whet stone ................................................................10

Fitting abrasive belts .........................................................10

Fitting polishing attachments ...................................................10

Switching on and oﬀ/setting speed range ........................................10

Using the grip ring with LED light ...............................................11

Notes on working with materials/tools/speed range ...............................11

Flexible shaft .............................................................. 13

Stand for the multi-tool .......................................................13

Router cage ...............................................................14

Changing the batteries ....................................................... 14

Cleaning, care and storage ........................................14

Kompernass Handels GmbH warranty ..............................15

Service .........................................................16

Importer .......................................................16

Disposal ........................................................16

Translation of the original Conformity Declaration .....................17

PFBS 160 B2

■ 2

│

GB

│

CY

PRECISION MULTI-GRINDER

PFBS 160 B2

Introduction

Congratulations on the purchase of your new appli-

ance. You have chosen a high-quality product. The

operating instructions are part of this product. They

contain important information about safety, usage

and disposal. Before using the product, please

familiarise yourself with all operating and safety

instructions. Use the product only as described and

for the range of applications speciﬁed. Please also

pass these operating instructions on to any future

owner.

Intended use

This precision drill grinder (hereafter also referred

to as the "appliance") is intended for drilling, mill-

ing, engraving, polishing, cleaning, grinding, cut-

ting of wood, metal, plastics, ceramics and stone

in dry rooms. Any other uses of or modiﬁcations

to the machine are deemed to be improper usage

and may result in serious physical injury. Not for

commercial use.

Features

Precision drill grinder:

ON/OFF switch

Power cable

Metal clip

Ventilation slits

Union nut

Tensioning nut

Collect chuck 3.2 mm (pre-assembled)

Grip ring with LED light

Spindle lock button

Carbon brushes

Inﬁnitely variable speed control

Accessories (see ﬁg. A):

Locking screw

Router cage

Flexible shaft

14b

Union nut (ﬂexible shaft)

Collet chuck mount

Stand mount

Stand

Clamping device

Accessories set (42 pieces) (see ﬁg. B):

6 cutting discs

2 grinding discs, abrasive

1 whet stone

3 polishing attachments

5 abrasive belts

1 abrasive belt mandrel

1 combination spanner

1 collet chuck 2.4 mm

1 metal brush

2 synthetic brushes

1 mandrel for cutting/grinding discs

1 drill bit

1 milling bit

1 mandrel for polishing attachments

2 engraving bits

5 grinding bits, abrasive

8 cutting discs

ON/OFF switch LED light

Package contents

1 precision multi-grinder PFBS 160 B2

1 plastic case

1 ﬂexible shaft

1 stand

1 clamping device

1 router cage

1 grip ring with LED light

1 accessories set (42 pieces)

1 set of operating instructions

PFBS 160 B2

GB

│

CY

│

3 ■

Technical data

Rated power

consumption: 160 W

Rated voltage: 230 V

~

, 50 Hz

(AC)

Rated speed: n 10,000–40,000 rpm

Drills

: max. Ø 3.2 mm

Discs: max. Ø 25 mm

Protection class: II / (double insulation)

Noise emission value:

Noise measurement value determined in accord-

ance with EN 60745. The rated noise level of the

power tool is typically as follows:

Sound pressure level: L

PA

= 80 dB(A)

Uncertainty K: K

PA

= 3 dB

Sound power level: L

WA

= 91 dB(A)

Uncertainty K: K

WA

= 3 dB

Wear hearing protection!

Vibration emission value:

Total vibration values (vector total of three direc-

tions) determined in accordance with EN 60745:

Vibration emission value: a

h

= 2.3 m/s

2

Uncertainty K = 1.5 m/s

2

NOTE

► The vibration level speciﬁed in these instruc-

tions has been measured in accordance with

a standardised measuring procedure and

can be used for equipment comparisons. The

speciﬁed vibration emission value can also

be used to make an initial exposure estimate.

WARNING!

► The vibration level will vary according to the

use of the power tool and may sometimes

be higher than the value speciﬁed in these

instructions. Regular use of the power tool in

this way may cause the user to underestimate

the vibration. Try to keep the vibration loads

as low as possible. Measures to reduce the

vibration load are, e.g. wearing gloves and

limiting the working time. Wherein all states

of operation must be included (e.g. times

when the power tool is switched oﬀ and times

where the power tool is switched on but run-

ning without load).

General Power Tool

Safety Warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instruc-

tions may result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂam-

mable liquids, gases or dust. Power tools cre-

ate sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

PFBS 160 B2

■ 4

│

GB

│

CY

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or ground-

ed surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of

electric shock if your body is earthed or ground-

ed.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entan-

gled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD re-

duces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites ac-

cidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related haz-

ards.

PFBS 160 B2

GB

│

CY

│

5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing ac-

cessories or storing power tools. Such preven-

tive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of

children. Do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may aﬀect

the power tools operation. If damaged, have

the power tool repaired before use. Many ac-

cidents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool

bits, etc. in accordance with these instruc-

tions, taking into account the working condi-

tions and the work to be performed. Use of

the power tool for operations diﬀerent from

those intended could result in a hazardous

situation.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

WARNING!

Always wear safety googles

Safety instructions for all applica-

tions

General safety instructions for grinding, sand-

paper sanding, working with wire brushes,

polishing, milling and abrasive cutting:

a) This power tool is intended for use as a grind-

er, sandpaper sander, wire brush, polisher,

milling machine and abrasive cutting appli-

ance. Please follow all safety instructions,

instructions, diagrams and data that you re-

ceive with the appliance. If you do not observe

the following instructions, this can lead to an

electrical shock, ﬁre and/or serious injuries.

b) Do not use any accessories that have not

been provided or recommended by the manu-

facturer for this power tool. Just because you

can attach the accessories to your power tool,

does not ensure they are safe to use.

c) The permissible speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the power tool. Acces-

sories that rotate faster than the permissible rate

can break and throw pieces into the air.

d) The external diameter and thickness of the

accessory tool used must comply with the di-

mensions of the power tool. Incorrectly dimen-

sioned accessory tools cannot be suﬃciently

shielded or controlled.

PFBS 160 B2

■ 6

│

GB

│

CY

e) Grinding discs, sanding drums or other ac-

cessories must match the grinding spindle or

collet chuck of your power tool exactly. Ac-

cessory tools which do not ﬁt precisely into the

take-up of the power tool will rotate unevenly,

vibrate severely and can lead to a loss of control.

f) Discs, grinding cylinders, cutting tools or

other accessories mounted on a mandrel must

be completely inserted in the collet or chuck.

Any "protrusion" or exposed parts of the

mandrel between the grinding tool and the

collet or chuck must be kept to a minimum.

If the mandrel is not suﬃciently tightened or the

grinding tool protrudes too far, the tool could

come loose and been thrown out at high speed.

g) Never use damaged accessory tools. Before

each use, check accessory tools such as

grinding discs for chips or cracks, sanding

drums for cracks, wearing or excessive wear

and tear and wire brushes for loose or bro-

ken wires. If the power tool or the accessory

tool in use is dropped, check to see if it is

damaged or use an undamaged accessory

tool.

When you have checked and inserted the

accessory tool, ensure that you and any other

people in the vicinity remain outside of the

range of the rotating accessory tool and al-

low the tool to rotate at maximum speed for

one minute. Damaged accessory tools usually

break during this test period.

h) Wear personal protective equipment.

Depending on the application, ensure that

you use full face protection, eye protection

or goggles. If required, use a dust mask, ear

protectors, protective gloves or special apron

to protect you from grindings and material

particles. The eyes should be protected from

ﬂying debris that may be caused during certain

applications. Dust or ﬁlter masks must be used

to ﬁlter any dust created by the application. If

you are exposed to loud noise for any length

of time, you may suﬀer hearing loss.

i) Ensure that other people remain at a safe dis-

tance to your workspace. Anyone who enters

the workspace must wear personal protective

equipment. Fragments of the workpiece or

broken accessory tools can ﬂy oﬀ and cause

injury – even outside the immediate working

area.

j) Hold the power tool only by the insulated

gripping surfaces when performing an opera-

tion where the accessory tool may contact

hidden wiring or its own cord. Contact with

a live cable may also cause metal parts of the

appliance to become live and may result in an

electric shock.

k) Always hold the power tool ﬁrmly. When

running up to full speed, the torque of the motor

can cause the power tool to twist.

l) If possible, use clamps to hold the workpiece

in position. Never hold a small workpiece

in one hand and the power tool in the other

while you are using it. By clamping small

workpieces, you keep both hands free for better

control of the power tool. When cutting round

workpieces such as dowels, rods or pipes, be

aware that these can roll away and this can

cause the tool to jam and be thrown towards

you.

m) Hold the power cord away from any rotating

accessories. If you lose control of the appli-

ance, the cord may get cut or caught and your

hand or arm could get caught in the rotating

accessory tool.

n) Never put the power tool down until the ac-

cessory tool has come to a complete stand-

still. The rotating accessory tool could come

into contact with the surface and cause you to

lose control of the power tool.

PFBS 160 B2

GB

│

CY

│

7 ■

o) When changing accessory tools or changing

settings, tighten the collet nut, the chuck or

other ﬁxing elements tightly. Loose ﬁxing ele-

ments can shift unexpectedly and lead to loss of

control; unﬁxed, rotating components will ﬂy oﬀ

violently.

p) Do not leave the power tool running whilst

carrying it. Accidental contact between your

clothing and the rotating accessory tool could

lead to a physical injury.

q) Clean the ventilation slits of your power tool

regularly. The engine fan draws dust into the

housing and a strong accumulation of metal

dust can cause electrical hazards.

r) Do not use the power tool in the vicinity of

ﬂammable materials. Sparks can ignite such

materials.

s) Do not use any accessory tools which require

liquid coolant. The use of water or other liquid

coolants may lead to an electric shock.

Additional safety instructions for all

applications

Kickback and corresponding safety instruc-

tions

Kickback is a sudden reaction caused when a

rotating accessory tool, e.g. grinding disc, abrasive

band, wire brush, etc., catches or jams. Catching

or jamming leads to an abrupt stop of the rotating

accessory tool. If this happens, an uncontrolled

power tool will turn rapidly against the direction

of rotation of the accessory tool.

If, for example, a grinding disc catches or jams,

the edge of the grinding disc that is projecting into

the workpiece can get caught and break oﬀ the

grinding disc or cause a kickback. The grinding

disc can then

ﬂy in the direction of the operator or away from

him, depending on the direction of rotation of the

disc at the blockage. This can also break grinding

discs.

A kickback is caused by incorrect use or misuse

of the power tool. This can be avoided by taking

proper precautions as described below.

a) Hold the power tool ﬁrmly in both hands

and position your body and arms so they

can absorb the force of a kickback. By taking

adequate precautions, the operator can stay in

control of the kickback forces.

b) Take special care when working around

corners, sharp edges, etc. Avoid allowing the

accessory tool to bounce back from the work-

piece or jam in the workpiece. The rotating

accessory tool is more likely to jam in corners or

sharp edges or if it rebounds oﬀ them. This can

cause a loss of control or kickback.

e) Do not use toothed saw blades. Such acces-

sories often cause a kickback or loss of control

over the power tool.

d) Always move the accessory tool in the same

direction in the material in which the cutting

edge leaves the material (in other words, the

same direction in which the dust is thrown

out). Guiding the power tool in the wrong direc-

tion will cause the cutting edge of the accessory

tool to jump out of the workpiece which can

lead to the accessory tool being pulled in this

direction.

e) Always ﬁx the workpiece when using rotary

ﬁles, cutting discs, high-speed milling tools or

hard-metal tools. Even a minimal tilting in the

groove can cause these tools to jam and lead

to a kickback. When the cutting disc jams, it

usually breaks. When a rotary ﬁle, high-speed

milling tool or hard-metal milling tool jams, the

accessory tool can jump out of the groove and

lead to loss of control of the power tool.

PFBS 160 B2

■ 8

│

GB

│

CY

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with the

edge of the disc. Any lateral application of

force on these grinding tools can lead to break-

age.

b) Use only undamaged mandrels of the correct

size and length and without undercut on the

shoulder for conical and straight pencil grind-

ers. Using an appropriate mandrel reduces the

risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or blocking and

thus the possibility of a setback or a breakage

of the grinding tool.

d) Avoid putting your hand in the area in front

of or behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc could be

thrown out directly towards you.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

g) Support panels or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides, namely in the

vicinity of the cut, and also at the edge.

h) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The protruding cutting disc may cut gas

or water pipes, electrical wiring or other objects

that can cause a kickback.

Supplementary safety instructions

for working with wire brushes

Special safety instructions for working with

wire brushes:

a) Be aware that the brush can lose wire bristles

even during normal operation. Do not over-

stress the wires by applying excessive pres-

sure to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) Allow the brush to run at working speed for

at least one minute before applying it to the

workpiece. Ensure that no one is standing in

front of or in line with the brush during this

time. Loose pieces of wire could ﬂy oﬀ during

the run-in period.

c) Aim the rotating steel brush away from your-

self. When working with these brushes, small

particles and minute pieces of wire can ﬂy oﬀ

at great speed and pierce skin.

PFBS 160 B2

GB

│

CY

│

9 ■

Safety instructions for LED lights

CAUTION! THERE IS A RISK OF

INJURY TO THE EYES!

■ Never aim the light directly at people or

animals and never look directly into the light

beam of the LED light.

General safety instructions for

batteries and cells

■ Do not expose batteries or cells to heat or open

ﬂames. Avoid storage in direct sunlight.

■ Cells or batteries must not be short-circuited.

Cells or batteries may not be stored danger-

ously in a box or draw where they can short-

circuit each other or be short-circuited by other

conductive materials.

■ Do not unpack a cell or battery until you plan

to use it.

■ Cells or batteries must not be exposed to

mechanical impacts.

■ If a cell is leaking, do not let the ﬂuid come into

contact with skin or eyes. If there is contact,

wash the aﬀected area with plenty of water and

seek medical assistance.

■ Do not use any other charger apart from the

one speciﬁcally designed for use with these

appliances.

■ Always observe the polarity markings – positive

(+) and negative (−) on the cells, batteries and

appliances. Ensure proper use.

■ Cells or batteries, that are not suitable for use

with the appliance may not be used.

■ Do not use combinations of batteries from diﬀer-

ent manufacturers, capacities, sizes or designs.

■ Keep cells and batteries out of the reach of

children.

■ If a cell or battery is swallowed, seek medical

assistance immediately.

■ Always purchase the correct cell or battery for

an appliance.

■ Keep cells and batteries clean and dry.

■ If the terminals of the cells or batteries are con-

taminated, clean them with a dry, clean cloth.

■ Store the original instructions and information

about the products safely for future information

and reference purposes.

■ Cells and batteries may not be used in applica-

tions for which they are not designed.

■ Always remove batteries from appliances that

are not in use, if possible.

■ Do attempt to recharge non-rechargeable

batteries.

There is a risk of explosion!

Original accessories/auxiliary

equipment

■ Use only the accessories and additional equip-

ment that are speciﬁed in the operating instruc-

tions and are compatible with the appliance.

PFBS 160 B2

■ 10

│

GB

│

CY

Use

Changing/inserting the tool/collet

chuck

♦ Press the spindle lock and hold it down.

♦ Turn the tensioning nut

until the lock clicks

into place.

♦ Undo the tensioning nut

from the thread

using the combination spanner .

♦ Remove any tool which is inserted.

♦ First push the intended tool through the tension-

ing nut

before inserting it into the appropri-

ate collet chuck

for the tool shaft.

♦ Press the spindle lock

and hold it down.

♦ Push the collet chuck

into the thread insert

and screw the tensioning nut tight with the

combination spanner .

Using an accessory tool with a mandrel:

♦ Use the screwdriver side of the combination

spanner

to undo and tighten the screw on

the mandrel.

♦ Insert the mandrel into the appliance as de-

scribed.

♦ Use the combination spanner

to undo the

screw on the mandrel.

♦ Insert the desired accessory tool between the

two washers on the screw.

♦ Use the combination spanner

to tighten the

screw on the mandrel.

Whet stone

♦ Do not manually grind any edges with the whet

stone

.

Fitting abrasive belts

♦ Push the abrasive belt onto the abrasive belt

mandrel from above. Tighten the screw on

the abrasive belt mandrel in order to ﬁx the

abrasive belt .

Fitting polishing attachments

♦ Screw the polishing attachment onto the tip

of the mandrel for polishing attachments .

Switching on and oﬀ/setting speed

range

CAUTION!

■ The rotation direction can be read oﬀ the

arrow engraved on the union nut

(anti-

clockwise symbol).

Switching on/setting the speed range:

♦ Set the ON/OFF switch

to the "I" position.

♦ Set the inﬁnitely variable speed control

to

a position between "1" and "MAX".

Switching oﬀ:

♦ Move the ON/OFF switch

to the position

"O".

PFBS 160 B2

GB

│

CY

│

11 ■

Using the grip ring with LED light

♦ Hold down the spindle lock and screw the

tensioning nut

anticlockwise oﬀ the thread.

♦ Release the spindle lock

.

♦ Then screw the union nut

anticlockwise oﬀ

the thread.

♦ Screw the grip ring with LED

clockwise onto

the screw thread.

♦ Hold down the spindle lock

and screw the

tensioning nut clockwise onto the thread.

♦ Release the spindle lock

.

♦ Move the ON/OFF switch of the LED light

to the position "I" to switch it on (see ﬁg. C).

♦ Move the ON/OFF switch of the LED light

to the position "O" to switch it oﬀ again.

♦ Proceed in reverse order to replace the union

nut

.

Notes on working with materials/

tools/speed range

■ Use the milling bits for working on wood, plas-

tics and plasterboard at maximum speed.

■ Determine the rotational speed range for work-

ing on zinc, zinc alloys, aluminium, copper and

lead by trying it out on test pieces.

■ Use a low rotational speed for work on plastics

and materials with a low melting point.

■ Use a high rotational speed for working on

wood.

■ Carry out cleaning, polishing and buﬃng work

in the medium speed range.

NOTE

► The milling bit

is not suitable for steel or

iron. Suitable products are available in stores.

The following are recommendations only and not

binding. When carrying out practical work, carry

out your own tests to see which tool and which set-

tings are ideal for the material you are working on.

Set a suitable rotational speed:

Number on the speed

control

Material being

worked

1 Plastics and materials

with a low melting

point

2–3 Stone, ceramics

4 Soft wood, metal

5 Hardwood

Max. Steel

PFBS 160 B2

■ 12

│

GB

│

CY

Application examples/selecting a suitable tool:

Function Accessories Use Protrusion

(min–max) mm

Drilling

Drill bit

Working wood 18–25, using the small-

est drill, the protrusion is

10 mm

Milling

Milling bit

Various jobs; e.g. creat-

ing recesses, hollows,

forms, grooves or slits

18–25

Engraving

Engraving bits

Labelling, handicraft 18–25

Polishing, rust removal

CAUTION!

Exert only slight pressure

when applying the tool

to the workpiece.

Metal brush

Rust removal 9–15

Polishing attachments

Various metals and

plastics, especially

precious metals such as

gold and silver

12–18

Cleaning

Synthetic brushes

e.g. cleaning hard-to-

access plastic housings

or the area around a

door lock

9–15

Grinding

Grinding discs

Grinding work on

stone, wood, ﬁne work

on hard materials such

as ceramics or alloyed

steel

12–18

Grinding bits

10

Abrasive belts

10

Disconnecting

Cutting discs

Working metal, plastic

and wood

12–18

PFBS 160 B2

GB

│

CY

│

13 ■

■ Note that the maximum diameter of the grind-

ing assembly and of grinding cones, pencil

grinders and grinding points with a thread insert

may not exceed 55mm and the maximum

diameter for sandpaper sanding accessories

may not exceed 80mm.

NOTE

► The max. permissible length of a mandrel is

33 mm.

■ Store the accessories in the original box or store

the accessory components somewhere else to

protect them from damage.

■ Store the accessories somewhere dry and not in

the vicinity of aggressive media.

■ If you exert too much pressure, the ﬁtted tool

can break and/or the workpiece could be dam-

aged. You will achieve optimum working results

by moving the tool over the workpiece at a

steady speed and while exerting light pressure.

■ When carrying out cutting work, hold the appli-

ance ﬁrmly with both hands.

■ Observe the data and the information in the ta-

ble to prevent the end of the spindle from touch-

ing the perforated base of the grinding tool.

Flexible shaft

■ Never operate the spindle lock while the motor

is running. Otherwise, the appliance or the ﬂex-

ible shaft may be damaged.

♦ Screw the union nut anticlockwise oﬀ the

appliance and store it carefully.

♦ Press the spindle lock

and hold it down.

♦ Screw the tensioning nut

anticlockwise oﬀ

the appliance.

♦ Fit the ﬂexible shaft

onto the appliance. To

do this, the internal access of the ﬂexible shaft

push the tensioning nut into the collet chuck

, .

♦ First tighten the tensioning nut

and then the

union nut

14b

of the ﬂexible shaft clockwise

onto the appliance with the combination span-

ner .

♦ Place the desired accessory into the collet

chuck

, of the ﬂexible shaft.

♦ Push the black the collar back onto the ﬂexible

shaft to lock the spindle.

♦ Open the collet chuck mount

on the ﬂexible

shaft with the combination spanner . Fit the

attachment and screw the collet chuck mount

back in place.

Stand for the multi-tool

♦ Screw the stand into the clamping device .

NOTE

► Depending on the desired attachment onto a

vertical or horizontal surface, you can screw

the stand

into the clamping device in two

diﬀerent positions.

♦ Screw the clamping device

onto the edge of

a work bench or table with a maximum thick-

ness of 55 mm.

♦ The stand

is height-adjustable. Undo the

upper part of the stand by turning it anti-

clockwise (−). Pull out the tube to the maximum

height and lock it again by turning it clockwise

(+).

♦ The mount

is also height-adjustable; turn

the black thread anticlockwise. After you have

set the mount to the correct height, tighten the

thread by turning in the opposite direction.

♦ Fix the appliance with the metal clip

onto the

mount of the stand . The mount can be

turned 360°.

PFBS 160 B2

■ 14

│

GB

│

CY

Router cage

With this attachment, the appliance is particularly suit-

able for cutting special forms (holes for plugs, etc.).

♦ Insert the milling bit

as described in the sec-

tion "Changing/inserting the tool/collet chuck".

♦ Ensure that the shaft of the bit protrudes out of

the collet chuck by about 13 mm.

♦ Screw the union nut

anticlockwise oﬀ the

appliance and store it carefully.

♦ Unscrew the router cage

oﬀ the appliance.

♦ To set the correct working height, undo the

locking screw

and adjust the foot of the

router cage to the desired size.

♦ Afterwards, retighten the locking screw

.

Changing the batteries

♦ Make sure that the LED light is turned oﬀ.

Remove the three screws from the rear of the

grip ring with LED

.

♦ Replace the used batteries in the appliance

with new batteries of the same type (button

cell LR41). Note polarity when installing new

batteries.

♦ Close the battery compartment again by re-

placing the three screws.

Cleaning, care and storage

WARNING! RISK OF INJURY!

■ Switch the appliance oﬀ and remove the

power plug before starting any work on

the appliance.

The appliance is maintenance-free.

■ Remove all dirt from the appliance. Use a dry

cloth to do this.

WARNING!

■ If the power cord requires replacement, this

should be carried out by the manufacturer or

an approved representative to avoid safety

hazards.

■ Store the appliance and all the individual piec-

es in the provided plastic case to ensure you do

not lose any part.

NOTE

► Replacement parts not listed (such as the

rechargeable battery, battery charger) can

be ordered via our service hotline.

WARNING!

■ Always ensure that the power plug or

the mains cable is replaced only by the

manufacturer of the appliance or by an

approved customer service provider. This

will ensure that the safety of the appliance is

maintained.

ca. 13 mm

PFBS 160 B2

GB

│

CY

│

15 ■

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The validity period of the warranty starts from the

date of purchase. Please keep your original receipt

in a safe place. This document will be required as

proof of purchase.

If any material or production fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

at our discretion. This warranty service is depend-

ent on you presenting the defective appliance and

the proof of purchase (receipt) and a short written

description of the fault and its time of occurrence.

If the defect is covered by the warranty, your product

will either be repaired or replaced by us. The repair

or replacement of a product does not signify the

beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance

with strict quality guidelines and inspected meticu-

lously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product parts

subject to normal wear and tear or fragile parts such

as switches, batteries, baking moulds or parts made

of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly maintained.

The directions in the operating instructions for the

product regarding proper use of the product are

to be strictly followed. Uses and actions that are

discouraged in the operating instructions or which

are warned against must be avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper handling,

use of force and modiﬁcations/repairs which have

not been carried out by one of our authorised

Service centres.

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g. IAN 12345) available as proof of purchase.

■ You will ﬁnd the item number on the type plate,

an engraving on the front page of the instructions

(bottom left), or as a sticker on the rear or bot-

tom of the appliance.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be provided

to you. Ensure that you enclose the proof of

purchase (till receipt) and information about

what the defect is and when it occurred.

NOTE

► For Parkside and Florabest tools, please send

us only the defective item without the acces-

sories (e.g. battery, storage case, assembly

tools, etc.).

You can download these instructions

along with many other manuals,

product videos and software on

www.lidl-service.com.

PFBS 160 B2

■ 16

│

GB

│

CY

Service

WARNING!

► Have the power tool repaired by the service

centre or a qualiﬁed electrician and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

► Always ensure that the power plug or the

mains cable is replaced only by the manu-

facturer of the appliance or by an approved

customer service provider. This will ensure

that the safety of the appliance is maintained.

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: k[email protected]

CY

Service Cyprus

Tel.: 8009 4409

E-Mail: k[email protected]

IAN 281406

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

Disposal

The packaging is made from environmen-

tally friendly material and can be dis-

posed of at your local recycling plant.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Please consult your local authorities regarding

suitable disposal of worn out power tools/battery

packs.

Batteries should not be disposed of

with normal household waste.

Consumers are legally obliged to dispose of used

batteries at a collection point in their town/district

or at a retail store. This obligation is intended to

ensure that batteries are disposed of in an environ-

mentally responsible manner. Dispose of batteries

only when they are fully discharged.

PFBS 160 B2

GB

│

CY

│

17 ■

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object

of the declaration described above complies with the requirements of the Directive 2011/65/EU of the

European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous sub-

stances in electrical and electronic appliances.

Applied harmonised standards:

EN 60745-2-23:2013

EN 60745-1:2009+A11:2010

EN 55014-1:2006/+A1:2009/+A2:2011

EN 55014-2:1997/+A1:2001/+A2:2008

EN 61000-3-2:2014

EN 61000-3-3:2013

Type/appliance designation:

Precision multi-grinder PFBS 160 B2

Year of manufacture: 09 - 2016

Serial number: IAN 281406

Bochum, 07/12/2016

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the context of further product development.

Pagina se încarcă ...

Parkside PFBS 160 B2 Manual de utilizare

Parkside PFBS 160 B2 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente