Panasonic SC-HTB527 Manualul proprietarului
- Categorie
- Seturi de difuzoare
- Tip
- Manualul proprietarului
Acest manual este potrivit și pentru
until
2013/01/21
EG EB
RQT9834-B
Operating Instructions
Home Theater Audio System
Model No. SC-HTB527
Thank you for purchasing this product.
Please read these instructions carefully before using this product,
and save this manual for future use.
Model number suffix “EB” denotes UK model.
Included Installation Instructions
The installation work should be done by a qualified installation specialist. (> 8 to 13)
Before commencing work, carefully read these installation instructions and the operating instructions
to ensure that installation is performed correctly.
(Please keep these instructions. You may need them when maintaining or moving this unit.)
SC-HTB527EGEB_RQT9834-B.book 1 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
2
RQT9834
Safety precautions
Unit
≥ To reduce the risk of fire, electric shock or
product damage,
jDo not expose this unit to rain, moisture,
dripping or splashing.
jDo not place objects filled with liquids, such as
vases, on this unit.
jUse only the recommended accessories.
jDo not remove covers.
jDo not repair this unit by yourself. Refer
servicing to qualified service personnel.
AC mains lead
≥ To reduce the risk of fire, electric shock or
product damage,
jEnsure that the power supply voltage
corresponds to the voltage printed on this unit.
jInsert the mains plug fully into the socket outlet.
jDo not pull, bend, or place heavy items on the
lead.
jDo not handle the plug with wet hands.
jHold onto the mains plug body when
disconnecting the plug.
jDo not use a damaged mains plug or socket
outlet.
≥ The mains plug is the disconnecting device.
Install this unit so that the mains plug can be
unplugged from the socket outlet immediately.
Button-type battery (Lithium battery)
≥ Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 60
o
C or
incinerate.
≥ Keep the Button-Type battery out of the reach of
children. Never put Button-Type battery in mouth.
If swallowed call your doctor.
Unit
≥ Do not place sources of naked flames, such as
lighted candles, on this unit.
≥ This unit may receive radio interference caused
by mobile telephones during use. If such
interference occurs, please increase separation
between this unit and the mobile telephone.
≥ This unit is intended for use in moderate climates.
Placement
≥ Place this unit on an even surface.
≥ To reduce the risk of fire, electric shock or
product damage,
jDo not install or place this unit in a bookcase,
built-in cabinet or in another confined space.
Ensure this unit is well ventilated.
jDo not obstruct this unit’s ventilation openings
with newspapers, tablecloths, curtains, and
similar items.
jDo not expose this unit to direct sunlight, high
temperatures, high humidity, and excessive
vibration.
Button-type battery (Lithium battery)
≥ Danger of explosion if battery is incorrectly
replaced. Replace only with the type
recommended by the manufacturer.
≥ Insert with poles aligned.
≥ Mishandling of batteries can cause electrolyte
leakage and may cause a fire.
jRemove the battery if you do not intend to use
the remote control for a long period of time.
Store in a cool, dark place.
jDo not heat or expose to flame.
jDo not leave the battery(ies) in a car exposed
to direct sunlight for a long period of time with
doors and windows closed.
≥ When disposing the batteries, please contact
your local authorities or dealer and ask for the
correct method of disposal.
WARNING CAUTION
SC-HTB527EGEB_RQT9834-B.book 2 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
RQT9834
3
Precautions
NORSK
Produkt
≥ For å redusere faren for brann, elektrisk støt
eller skade på apparatet:
jUtsett ikke produktet for regn, fukt, drypping
eller sprut.
jIkke plasser objekter som er fylt med væske,
som vaser, på apparatet.
jBruk kun anbefalt tilbehør.
jFjern ikke deksler.
jReparer ikke denne enheten selv, overlat
service til kvalifisert servicepersonell.
Vekselstrømnett
≥ Nettstøpselet er trukket ut fra denne enheten.
Installer denne enheten slik at nettstøpselet
umiddelbart kan trekkes fra stikkontakten.
Produkt
≥ Plasser ikke åpen ild, slik som levende lys, oppå
apparatet.
≥ Dette apparatet er beregnet for bruk under
moderate klimaforhold.
Plassering
≥ For å redusere faren for brann, elektrisk støt
eller skade på apparatet:
jIkke plasser apparatet i en bokhylle, et
innebygget kabinett eller et annet lukket sted.
Pass på at produktet er godt ventilert.
jApparatets ventilasjonsåpninger må ikke
dekkes til med aviser, duker, gardiner eller
lignende.
Caution for AC Mains
Lead
(For the AC mains plug of three pins)
For your safety, please read the following text
carefully.
This appliance is supplied with a moulded three
pin mains plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure
that the replacement fuse has a rating of 5-ampere
and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark Ï or the BSI mark Ì on
the body of the fuse.
If the plug contains a removable fuse cover you
must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be
used until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local dealer.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of
AC mains plug (figures A and B). Confirm the AC
mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
2. Replace the fuse and close or attach the fuse cover.
Safety information for customers in Norway
ADVARSEL
FORSIKTIG
Figure A Figure B
Fuse cover
Figure A Figure B
Fuse
(5 ampere)
Fuse
(5 ampere)
SC-HTB527EGEB_RQT9834-B.book 3 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
4
RQT9834
Table of contents
Safety precautions .............................................................................................. 2
Caution for AC Mains Lead ................................................................................ 3
Before use
Supplied items ..................................................................................................... 5
This system (SC-HTB527) ...................................................................................................... 5
Accessories ............................................................................................................................. 5
Control reference guide ...................................................................................... 6
This system (Front) ................................................................................................................. 6
This system (Rear) .................................................................................................................. 6
Remote control ........................................................................................................................ 7
Getting started
Step 1 Selecting the placement method .......................................................... 8
The main unit ..........................................................................................................................8
The active subwoofer .............................................................................................................. 9
Wireless interference ..............................................................................................................9
Step 2 Placement ............................................................................................. 10
When placing the main unit in a rack or on a table ............................................................... 10
When attaching the main unit to a wall .................................................................................11
Step 3 Connections .......................................................................................... 14
Connection with the TV .........................................................................................................14
Connection from an HDMI compatible device .......................................................................15
Digital transmitter connection ................................................................................................ 15
AC mains lead connection .................................................................................................... 16
Active subwoofer wireless connection .................................................................................. 16
Operations
Using this system ............................................................................................. 17
3D sound ............................................................................................................ 18
Audio output modes .............................................................................................................. 18
Linked operations with the TV (VIERA Link “HDAVI Control
TM
”) ................. 19
Advanced operations ........................................................................................ 20
Reference
Troubleshooting ................................................................................................ 21
Unit care ............................................................................................................. 23
Licenses ............................................................................................................. 23
Specifications .................................................................................................... 24
SC-HTB527EGEB_RQT9834-B.book 4 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Getting started
Operations
RQT9834
5
Reference
Before use
Precautions
Before use
Supplied items
Check the supplied accessories before using this system.
≥ Product numbers are correct as of December 2012. These may be subject to change.
≥ The supplied AC mains lead is for use with this system only.
Do not use it with other equipment. Also, do not use cords from other equipment with this system.
≥ The illustrations shown may differ from your unit.
≥ These operation instructions are applicable to model SC-HTB527 for variety of regions.
Unless otherwise indicated, illustrations in these operating instructions are of the model for the
United Kingdom and Ireland.
≥ Operations in this operating instructions are described mainly with the remote control, but you
can perform the operations on the main unit if the controls are the same.
This system (SC-HTB527)
∏ 1 Main unit (speaker)
(SU-HTB527)
∏ 1 Active subwoofer
(SB-HWA527)
∏ 1 Digital transmitter
≥ Supplied with the active subwoofer.
Accessories
∏ 1 Remote control
(with a battery)
(N2QAYC000043)
∏ 2 AC mains leads
For the United Kingdom and
Ireland
(K2CT2YY00097)
For continental Europe
(K2CQ2YY00119)
∏ 4 Safety holders
(RFA3321-K)
∏ 2 Wall mount brackets
(RMQX1082-K)
∏ 2 Rear Pads
(RMG0850-K)
∏ 4Screws
(with washerk2:
XYN5+J14FJK)
(without washerk2:
XSN4+8FJK)
SC-HTB527EGEB_RQT9834-B.book 5 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
6
RQT9834
Control reference guide
1 Standby/on switch (Í/I)
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the unit
is still consuming a small amount of power.
2 Adjust the volume of this system
3 Select the input source
“TV” !# “BD/DVD”
4 Input selector indicators (> 17)
A TV indicator
Lights green when the TV is the audio
source
B BD/DVD indicator
Lights amber when the device connected to
the HDMI IN terminal is the audio source
5 Remote control signal sensor (> 7)
6 Audio format indicators* (> 17)
C Dolby
®
Digital indicator
Lights when Dolby Digital is the current
audio format
D DTS indicator
Lights when DTS is the current audio
format
E PCM indicator
Lights when PCM (2ch, Multi-channel) is
the current audio format
7 WIRELESS LINK indicator (> 16)
1 AC IN terminal (> 16)
2 Digital transmitter dock (> 15)
3 OPTICAL DIGITAL AUDIO IN terminal (> 14)
4 HDMI OUT terminal (ARC compatible) (> 14)
5 HDMI IN terminal (> 15)
6 Active subwoofer on/off button
* The indicators will also blink in various conditions. (> 22)
This system (Front)
1
46
5
7
23
Main unit Active subwoofer
This system (Rear)
DIGITAL TRANSMITTER
1
6
3
4
5
1
2
SC-HTB527EGEB_RQT9834-B.book 6 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Before use
RQT9834
7
1 Turn the main unit on or off (> 17)
2 Select the input source (> 17)
≥ [TV]:
Select the TV as the source
≥ [BD/DVD]:
Select the device connected to the HDMI IN
terminal as the source
3 Adjust the output level of the active subwoofer
(bass sound) (> 17)
4 Adjust the volume of this system (> 17)
5 Mute the sound (> 17)
Remote control
1
2
3
4
5
∫ Before using for the first time
Remove the insulation sheet A.
∫ To replace a button-type battery
Battery type: CR2025 (Lithium battery)
≥ Set the button-type battery with its (i) mark
facing upward.
≥ Keep the button-type battery out of reach of
children to prevent swallowing.
∫ Remote control operation range
The remote control signal sensor is located on the main unit.
≥Use the remote control within the correct operation range.
BD/DVD
D
B Remote control signal sensor
≥ Operation range
Distance: Within approx. 7 m
directly in front
Angle: Approx. 30
o
left and right
SC-HTB527EGEB_RQT9834-B.book 7 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
8
RQT9834
Getting started
Step 1 Selecting the placement method
≥Choose a placement method that suits you best.
≥ Keep the safety holders, screws, rear pads and wall mount brackets out of reach of children to prevent swallowing.
≥ The safety holder is to minimize the possibility of damage and harm, but it does not completely guarantee this effect.
≥ Do not hold the main unit in one hand to avoid injury, you may drop the main unit when carrying it.
≥ To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
The main unit
Safety Precautions
Professional installation is required.
The installation should never be done by any other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING
DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.
≥ Be sure to install the main unit as indicated within this operating Instructions.
≥ Attach using techniques suited to the structure and materials of the installation location.
Caution
≥ This system is to be used only as indicated in these instructions. Failure to do so may lead to damage to
the amplifier and/or the speaker, and may result in the risk of fire. Consult a qualified service person if
damage has occurred or if you experience a sudden change in performance.
≥ Do not attempt to attach the main unit to a wall using methods other than those described in this manual.
When attaching the main unit to a wall
When placing the main unit in a rack or on a table
Page 10
Page 11
SC-HTB527EGEB_RQT9834-B.book 8 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Getting started
Precautions
RQT9834
9
When carrying the active subwoofer
To avoid interference, maintain the following distances between the main unit/active subwoofer and
other electronic devices that use the same radio frequency (2.4 GHz band).
≥ Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward.
≥ Do not use the main unit or the active subwoofer in a metal cabinet.
≥ Placing the active subwoofer too close to the walls and corners can result in excessive bass. Cover walls and windows with thick
curtains.
≥ If irregular colouring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the main unit further away from
the TV.
≥ Keep magnetised items away. Magnetised cards, watches, etc., can be damaged if placed too close to the main unit and active
subwoofer.
∫ When placing the main unit in front of the TV
The main unit may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic Tracking
System) sensor, remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D compatible TV.
≥Move the main unit further away from the TV. If the TV still does not function correctly, try using it in a
rack or in the wall mount position.
The active subwoofer
A Do not hold the active subwoofer from this
opening.
The parts inside may get damaged.
B Always hold the bottom of the active subwoofer when
moving it.
Wireless interference
C Main unit/active subwoofer
D Wireless router, cordless phone and other
electronic devices: approx. 2 m
A
B
D
C
SC-HTB527EGEB_RQT9834-B.book 9 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
10
RQT9834
Step 2 Placement
Supplied components
Commercially available components (not supplied)
≥Fall prevention cord............................................................................................................................ k 2
≥Screw eyes (to attach the fall prevention cord) .................................................................................. k 2
≥ Use commercially available screws that are capable of supporting over 33 kg.
≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).
Attach the cord to the safety holder.
Attach the safety holder to the main unit.
≥ Screw tightening torque: 80 N0cm to 120 N0cm.
When placing the main unit in a
rack or on a table
∏ 2 Safety holders ∏ 2 Screws with washer
A Safety holder (supplied)
B Cord
C Thread the cord through the holes.
Refer to the operating instructions of the
cord for details.
D Screw with washer (supplied)
≥ Tighten securely.
E Safety holder (supplied)
F Projecting part
≥ The safety holder is placed
diagonally.
SC-HTB527EGEB_RQT9834-B.book 10 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Getting started
Precautions
RQT9834
11
Place the main unit in the desired position and attach each cord onto the
rack or table.
≥ Make sure that the slack of the cord is minimal.
Supplied components
Commercially available components (not supplied)
≥Screws for wall mounting................................................................................................................... k 4
≥Fall prevention cord........................................................................................................................... k 2
≥Screw eyes (to attach the fall prevention cord) ................................................................................. k 2
≥ Use commercially available screws with a nominal diameter of 4.0 mm, which are suitable to the material of the wall (e.g., wood,
steel, concrete, etc.) and are capable of supporting over 33 kg.
≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).
Locate the screwing positions on the wall.
≥ Use the measurements indicated below to identify the screwing positions on the wall.
≥ Position the main unit with at least 50 mm of space above it. If not, it may not be possible to access the buttons.
≥ The position on the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg.
≥ Be sure to use a spirit level to ensure that both screwing positions are horizontal to each other.
G Screw eye
≥ Attach at a position capable of
supporting over 33 kg.
≥ Depending on the placement of
the main unit, the screwing
position of the screw eye may
differ.
When attaching the main unit to a wall
∏ 4 Safety holders ∏ 2 Wall mount brackets
∏ 2 Rear pads ∏ 2 Screws with
washer
∏ 2 Screws without
washer
A Wall mount bracket (supplied)
252 mm257 mm 233.5 mm 275.5 mm
1018 mm
75 mm
31.5 mm
43.5 mm
12.5 mm
A A
SC-HTB527EGEB_RQT9834-B.book 11 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
12
RQT9834
Attach the wall mount brackets to the wall.
Complete all the necessary connections to the main unit. (> 14 to 16)
≥
Connect the AC mains lead cord to the main unit, but do not connect it to the household mains socket until the installation is completed.
Attach the rear pads to the rear of the main unit.
Attach the cord to the safety holder.
Attach the safety holder to the main unit.
≥ Screw tightening torque: 80 N0cm to 120 N0cm.
B Wall mount bracket (supplied)
C Screws
≥ Tighten securely.
D At least 30 mm
E ‰4.0 mm
F ‰7.5 mm to ‰9.4 mm
G Wall
H Wall mount bracket (supplied)
I Rear pads
(supplied)
J Safety holder (supplied)
K Cord
L Thread the cord through the holes.
Refer to the operating instructions of
the cord for details.
M Screw with washer (supplied)
≥ Tighten securely.
N Safety holder (supplied)
O Projecting part
≥ The safety holder is placed
diagonally.
SC-HTB527EGEB_RQT9834-B.book 12 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Getting started
Precautions
RQT9834
13
Attach the main unit to the wall mount brackets.
Screw the safety holder onto the wall mount brackets.
≥ Screw tightening torque: 80 N0cm to 120 N0cm.
≥ The safety holders are designed to prevent the main unit from falling off the wall mount bracket.
Secure the cord to the wall.
≥ Make sure that the slack of the cord is minimal.
≥ Check the strength of the installation location.
The position should be capable of supporting over 33 kg. If the strength at any of these positions is lacking, provide sufficient
reinforcement.
P Wall mount bracket (supplied)
Q Gently move the main unit down onto the wall mount bracket.
R Screw without washer (supplied)
≥ Tighten securely.
S Safety holder (supplied)
T Wall mount bracket (supplied)
U Wall
V About 15
o
≥ Tilt about 15
o
from the wall and tighten the screw.
W Screw eye
X Cord
SC-HTB527EGEB_RQT9834-B.book 13 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
14
RQT9834
Step 3 Connections
≥Turn off all equipment before connection and read the appropriate operating instructions.
Do not connect the AC mains lead until all other connections are completed.
∫ HDMI
≥ The HDMI connection supports VIERA Link “HDAVI Control” (> 19) when used with a compatible Panasonic TV.
≥ Use the ARC compatible High Speed HDMI Cables. Non-HDMI-compliant cables cannot be utilised.
≥ It is recommended that you use Panasonic’s HDMI cable.
Verify if the TV’s HDMI terminal is labelled “HDMI (ARC)”.
∫ What is ARC?
ARC is an abbreviation of Audio Return Channel, also known as HDMI ARC. It refers to one of the HDMI functions. When you
connect the main unit to the terminal labelled “HDMI (ARC)” on the TV, the optical digital audio cable that is usually required in order
to listen to sound from a TV is no longer required, and TV pictures and sound can be enjoyed with a single HDMI cable.
Make the connection.
A HDMI cable
A HDMI cable B Optical digital audio cable
≥ Be sure to place the cable under the projecting part.
≥ When you use the optical digital audio cable, insert the tip
correctly into the terminal.
Connection with the TV
Connection differs depending on the label printed next to the HDMI terminal.
Labelled “HDMI (ARC)”: Connection [A]
Not Labelled “HDMI (ARC)”: Connection [B]
[A] Labelled “HDMI (ARC)”
A
TV
HDMI IN (ARC)
HDMI OUT
Be sure to connect to the TV’s ARC
compatible terminal. (Refer to the
operating instructions for the TV.)
[B] Not labelled “HDMI (ARC)”
A
B
TV
HDMI IN
OPTICAL
OUT
HDMI OUT
OPTICAL DIGITAL
AUDIO IN
SC-HTB527EGEB_RQT9834-B.book 14 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Getting started
RQT9834
15
You can direct the audio signal from the connected Blu-ray Disc player, DVD player, Set Top Box, etc. to
this system.
Preparation
≥Connect the main unit to the TV. (> 14)
A HDMI cable B e.g., Blu-ray Disc player
≥ Refer to the operating instructions of the connected HDMI compatible device for the necessary setting, to output the video and
audio signals.
A Digital transmitter (supplied)
Insert the digital transmitter, with the label facing down, until you hear a click.
Connection from an HDMI compatible device
HDMI IN
B
HDMI OUT
A
∫ HDMI standby pass-through
Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the HDMI IN terminal will be
sent to the TV connected to the HDMI OUT terminal (the sound will not be output from this system).
∫ 3D compatibility
Compatible with FULL HD 3D TV and Blu-ray Disc player.
≥ The main unit can pass through the 3D video signal from a 3D compatible Blu-ray Disc player to a FULL HD 3D TV.
Digital transmitter connection
Do not insert or remove while the main unit is turned on.
DIGITAL TRANSMITTER
A
SC-HTB527EGEB_RQT9834-B.book 15 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
16
RQT9834
≥ Connect only after all other connections are completed.
≥This system consumes a small amount of AC power (> 24) even when it is turned off. In the interest of
power conservation, if you will not be using this system for a long time, unplug it from the household
mains socket.
Preparation
≥Turn on the main unit.
Press [BÍ CI].
Active subwoofer on/off button [B Í C I]
Use this button to turn the active subwoofer on and
off.
C I:
The active subwoofer is on.
B Í:
The active subwoofer is off.
The active subwoofer will still consume a small
amount of power even when it is turned off (B, Í).
Check that the wireless link is
activated.
WIRELESS LINK indicator lights
≥ Red:
The wireless link is not activated.
≥ Green:
The wireless link is activated.
AC mains lead connection
For customers in United Kingdom and Ireland
BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 3 BEFORE CONNECTION.
Saving energy
The main unit is designed to conserve its power consumption and save energy.
≥ The main unit will automatically switch to standby mode when no signal is input and no operation is
performed for approx. 2 hours. Refer to page 20, “Auto standby function” to turn this function off.
AC IN
AC IN
A To a household mains socket
B AC mains lead (supplied)
Active subwoofer wireless connection
SC-HTB527EGEB_RQT9834-B.book 16 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Getting started
Operations
RQT9834
17
Operations
Using this system
Preparation
≥ Turn on the active subwoofer.
≥ Turn on the TV and/or connected device.
Press [Í] to turn on the main unit.
Press [TV] or [BD/DVD] to select the
audio source.
≥ If you have selected [BD/DVD], make sure to
select the TV’s input channel for this system and
start the playback.
≥ If there is sound coming out of the TV’s speakers, reduce the
volume of the TV to its minimum.
≥ The maximum volume of the TV and this system may be
different.
≥ If the main unit is turned off with the volume setting in the
greater half (above 50), the main unit will automatically lower
the volume to the middle (50) when the main unit is turned on
(Volume limitation).
To turn this function off, refer to page 21.
Press [i VOL j] to adjust the volume.
≥ Volume range: 0 to 100
Press [i SUBWOOFER j] to adjust the
subwoofer level.
≥ Subwoofer levels: 1 to 4
A The indicators blink from left to right (i) or from
right to left (s) while adjusting.
≥ The indicators will not blink when it has reached
the maximum or minimum.
Press [MUTE].
A The indicators blink simultaneously while
muting.
≥ To cancel, press the button again or adjust the volume.
≥ Muting is cancelled if the main unit is turned off.
Press the button for the current audio
source ([TV] or [BD/DVD]).
≥ The current audio format is indicated for 4 sec.
A Lights when Dolby Digital is the audio format
B Lights when DTS is the audio format
C Lights when PCM or LPCM is the audio format
≥ The audio format status is also indicated for 4 sec if the audio
format on the selected source (TV, Blu-ray Disc/DVD Player,
etc.) is changed.
If this system does not operate as expected
or sound is unusual, returning the settings
to the factory preset may solve the problem.
(> 21)
1
2
To adjust the volume/
subwoofer level
To mute the sound
To display the current audio
format
TV
BD/DVD
DTS PCMD
A
A B C
SC-HTB527EGEB_RQT9834-B.book 17 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
18
RQT9834
3D sound
This system provides a feeling that the sound and
the image are as one.
≥ To change the applied effect, refer to “Audio
output modes”. (> right)
Dolby Virtual Speaker and the 3D surround effects can be
turned off and on by changing the audio output mode settings.
(> right)
By changing the audio output mode, it is possible to
enjoy the sound that is suitable to the TV program
or image from the connected device.
Press and hold [MUTE] for more than
2 sec.
While the indicator is blinking, press
[MUTE] again to change the setting.
A Multi-channel mode
B Auto mode (Direct mode)
*
C 2ch mode
≥ The setting changes each time [MUTE] is pressed.
≥ The indicator for the current setting blinks for 10 sec.
* Depending on the audio source, Dolby Virtual Speaker and
3D surround effect settings are automatically adjusted.
The indicator will also light when the audio source is
Multi-channel audio during Auto Mode.
≥ When using the optical digital audio cable, Dolby Virtual
Speaker and the 3D surround effect will be temporarily
cancelled if the audio signal’s sampling frequency is greater
than 48 kHz.
3D sound
Dolby Virtual
Speaker
With this effect you can enjoy a
surround sound effect similar
to 5.1ch.
3D surround
effect
Adding to the Dolby Virtual
Speaker effect, Panasonic has
applied its own sound field
controlling technology to
expand the sound field
forwards, backwards, upwards,
and downwards, providing a
sound with depth and force
that better matches 3D
images.
Clear-mode
dialog
Sports commentary and
dialogs from TV dramas are
heard as if the sound is coming
from the TV, giving the feeling
that the sound and the image
are one.
Also, the dialog will stand out
from the other sounds during
normal volume playback and
when the volume is lowered for
night time viewing.
e.g., Image of 3D sound field
Audio output modes
Audio output
mode
Dolby Virtual Speaker
and 3D surround effect
Multi-channel
mode
The effects are applied
to all audio sources.
Auto mode
(Direct mode)
(Factory preset)
The effects are applied
to Multi-channel audio
sources.
The effects are not
applied to 2 channel
audio sources.
2ch mode
The effects are not
applied to any audio
source.
To change the audio output
mode
TV
BD/DVD
DTS PCMD
A B C
SC-HTB527EGEB_RQT9834-B.book 18 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Operations
RQT9834
19
Linked operations with the TV
(VIERA Link “HDAVI Control
TM
”)
Preparation
1 Confirm that the HDMI connection has been
made. (> 14, 15)
2 Set the “HDAVI Control” operations on the
connected equipment (e.g., TV).
3 For the optimal “HDAVI Control” operations
change the following settings on the connected
TV*
1
.
≥ Set the default speaker settings to this system*
2
.
≥ Set the speaker selection settings to this system.
4 Turn on all “HDAVI Control” compatible
equipment and select the TV’s input for this
system so that the “HDAVI Control” function
works properly.
5 If a device is connected to the HDMI IN
terminal, start play to check that the picture is
displayed on the TV correctly.
When the connection or settings are changed,
repeat this procedure.
*1
The availability and function of the settings may vary
depending on the TV. Refer to the operating instructions for
the TV for details.
*2
If the TV has a default speaker setting within the VIERA Link
setting items, choosing this system as the default speaker
will automatically change the speaker selection to this
system.
≥ VIERA Link “HDAVI Control”, based on the control functions
provided by HDMI which is an industry standard known as
HDMI CEC (Consumer Electronics Control), is a unique
function that we have developed and added. As such, its
operation with other manufacturers’ equipment that supports
HDMI CEC cannot be guaranteed.
≥ This unit supports “HDAVI Control 5” function.
“HDAVI Control 5” is the standard for Panasonic’s HDAVI
Control compatible equipment. This standard is compatible
with Panasonic’s conventional HDAVI equipment.
≥ Please refer to individual manuals for other manufacturers’
equipment supporting VIERA Link function.
To make sure that the audio is output from this
system, turn the main unit on by using the TV’s
remote control and selecting home cinema from the
speaker menu of VIERA Link menu.
The availability and function of the settings may
vary depending on the TV. Refer to the operating
instructions for the TV for details.
∫ Speaker control
You can select whether audio output is from this
system or the TV speakers by using the TV menu
settings.
Home cinema
This system is active.
≥
When the main unit is in standby mode, changing the TV
speakers to this system in the VIERA Link menu will
automatically turn the main unit on and select TV as the
source.
≥ You can control the volume setting of this system using the
volume or mute button on the TV remote control.
≥ If you turn off the main unit, the TV speakers will be
automatically activated.
≥ Audio will automatically be output from this system if the TV
is compatible to VIERA Link “HDAVI Control 4” or later.
TV
TV speakers are active.
≥ The volume of this system is set to its minimum.
∫ Automatic input switching
When the following operations are performed, the
main unit will automatically change the input to the
corresponding source.
j
When play starts on an HDMI connected device.*
3
jWhen the TV input or the TV channel is changed.
*3
If the speaker output setting on the TV is set to this system,
the TV and the main unit turn on automatically (Power on
link).
∫ Power off link
When the TV is turned off, the main unit also turns
off automatically.
∫ Automatic lip-sync function
(for HDAVI Control 3 or later)
Delay between audio and video is automatically
adjusted by adding time-lag to the audio output,
enabling you to enjoy smooth audio for the picture.
The delay information is automatically set if the TV is
compatible to VIERA Link “HDAVI Control 3” or later and the
VIERA Link is set to on.
What is VIERA Link “HDAVI
Control”?
VIERA Link “HDAVI Control” is a convenient
function that offers linked operations of this
system, and a Panasonic TV (VIERA) under
“HDAVI Control”.
You can use this function by connecting the
equipment with an HDMI cable. See the
operating instructions for connected
equipment for operational details.
What you can do with
VIERA Link “HDAVI Control”
SC-HTB527EGEB_RQT9834-B.book 19 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
20
RQT9834
Advanced operations
Change the dual audio from main to secondary.
≥ This setting will only work if the audio output
setting on the connected TV or player, etc. is set
to “Bitstream” and dual audio is available in the
audio source.
Press and hold [BD/DVD] for more
than 2 sec.
While the indicator of the current
setting is flashing, press [BD/DVD] to
change the setting.
A Main
B Secondary (SAP: Secondary Audio Program)
A, B: Main and secondary
≥ The indicator for the selected setting flashes for
10 seconds and then exits the setting mode.
≥ The setting is maintained until it is changed again.
≥ The default setting of this function is main.
If no signal is input and no operation is performed for
2 hours, the main unit will switch to standby mode.
To change the setting of this function:
Press and hold [INPUT SELECTOR]
on the main unit for more than 2 sec.
While the indicator of the current setting
is flashing, press [INPUT SELECTOR] to
change the setting.
A Auto standby function is on.
B Auto standby function is off.
≥ The indicator for the selected setting flashes for
10 seconds and then exits the setting mode.
≥ The setting is maintained until it is changed again.
≥ The default setting of this function is on.
Depending on your preference, It is possible to turn off
the 3D surround effect and the clear-mode dialog effect.
Press and hold [TV] for more than 2 sec.
While the indicator is blinking, press
[TV] to change the setting.
A 3D surround effect and clear-mode dialog
effect is on.
B 3D surround effect and clear-mode dialog
effect is off.
≥ The indicator for the selected setting flashes for
10 seconds and then exits the setting mode.
≥ This setting will be reset to on when the main unit is turned
off.
≥ When off is selected, the dialog effect level cannot be
adjusted.
∫ Remote control code
When other Panasonic devices respond to this
system’s remote control, change the remote control
code on this system and the remote control.
Preparation
≥ Turn off all other Panasonic products.
≥ Turn on the main unit.
Change the remote control code to code 2:
1 Aim the remote control at the main unit’s
remote control sensor.
2 Press and hold [MUTE] and [BD/DVD] on the
remote control for more than 4 sec.
A will blink for 10 sec when the code of this system
is changed.
≥ The setting is maintained until it is changed again.
≥ If the main unit does not operate after changing the code,
repeat steps 1 and 2.
≥ To change the remote control to code 1, repeat the steps
above, but replace [BD/DVD] with [TV].
Changing the dual audio
Auto standby function
TV
BD/DVD
DTS PCMD
A B
TV
BD/DVD
DTS PCMD
A B
Using the Dolby
Virtual Speaker effect
Others
TV
BD/DVD
DTS PCMD
A B
TV
BD/DVD
DTS PCMD
A
SC-HTB527EGEB_RQT9834-B.book 20 ページ ２０１２年１２月１０日 月曜日 午前１１時２９分
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Panasonic SC-HTB527 Manualul proprietarului
- Categorie
- Seturi de difuzoare
- Tip
- Manualul proprietarului
- Acest manual este potrivit și pentru
în alte limbi
- English: Panasonic SC-HTB527 Owner's manual
Lucrări conexe
-
Panasonic SCHTB385EB Manualul proprietarului
-
-
-
-
-
Panasonic SCHTE200EB Manualul proprietarului
-
-
-
-