Sony VPL-VZ1000 Manualul proprietarului

Tip
Manualul proprietarului
4-693-527-12(1)
© 2017 Sony Corporation
Printed in Japan
Video Projector
VPL-VZ1000
Safety Regulations
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
WARNING
THIS APPARATUS MUST BE EARTHED.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
When you dispose of the battery, you must obey the law in the relative area or
country.
WARNING
When installing the unit, incorporate a readily accessible disconnect device in
the fixed wiring, or connect the power plug to an easily accessible socket-outlet
near the unit.
If a fault should occur during operation of the unit, operate the disconnect
device to switch the power supply off, or disconnect the power plug.
CAUTION
About the LAN connector
For safety, do not connect the connector for peripheral device wiring that might
have excessive voltage to this port.
WARNING
1. Use the approved Power Cord (3-core mains lead) / Appliance Connector /
Plug with earthing-contacts that conforms to the safety regulations of each
country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug
conforming to the proper ratings (Voltage, Ampere).
If you have questions on the use of the above Power Cord / Appliance Connector /
Plug, please consult a qualified service personnel.
Caution
Two size AA (R6) batteries are required for Remote Control.
To avoid risk of explosion, use size AA (R6) manganese or alkaline batteries.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in
this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to
comply with the limits for a digital device pursuant to Subpart B of part 15 of FCC
Rules.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
If you have any questions about this product, you may call;
Sony Customer Information Service Center
1-800-222-7669 or http://www.sony.com/
Declaration of Conformity
Trade Name: SONY
Model: VPL-VZ1000
Responsible party: Sony Electronics Inc.
Address: 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
For the customers the U.S.A. and Canada
Radiated Exposure Statement:
The product complies with the US/Canadian portable RF exposure limit set forth
for an uncontrolled environment and is safe for intended operation as described
in this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or if the device is set to lower
output power if such function is available.
For the customers in Canada
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
For the customers in Canada
CAN ICES-3 (B)/NMB-3(B)
CAUTION
When you connect the LAN cable of the unit to peripheral device, use a
shielded-type cable to prevent malfunction due to radiation noise.
For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
For the customers in the U.S.A. (Also where IEC 62368-1:2014 is
applicable)
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This product is classified as a CLASS 2 LASER PRODUCT.
WARNING
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
CAUTION
Do not look into the lens while in use.
CAUTION
Do not allow children to operate this product without supervision.
CAUTION
The use of optical instruments with this product will increase eye hazard.
For the customers in other countries
IEC 60825-1:2014
CLASS 1 LASER PRODUCT
As with any bright light source, do not stare into the
beam, RG2 IEC 62471-5:2015.
WARNING: Do not look into the lens while in use.
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Caution
The use of optical instruments with this product will increase eye hazard.
För kunderna i Sverige
IEC 60825-1:2014
LASERPRODUKT AV KLASS 1
Precis som med alla starka ljuskällor bör man inte titta
direkt i strålen, RG2 IEC 62471-5:2015.
VARNING: Titta aldrig in i projektorns lins medan den används.
Försiktighet!
Användandet av kontroller eller justeringar eller utförandet av andra procedurer
än de som specificeras häri kan resultera I exponering av farlig strålning.
Försiktighet!
Användandet av optiska instrument med denna produkt ökar risk för ögonskada.
Location information of the labels
Laser Aperture
CAUTION LABEL
CLASS 1 LABEL
Light source specifications
3.75 W laser diode × 24 (450 - 460 nm)
Beam divergence angle from lens
of this unit
α = 133°
Caution on replacement/disposal of the battery for the 3D glasses
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
When you dispose of the battery, you must obey the law in the relative area or
country.
About 3D Glasses
The 3D Glasses communicate with the projector via Bluetooth technology to
display 3D signals.
(a) frequency band(s) in which the radio equipment operates:
2.4 - 2.4835 GHz
(b) maximum radio-frequency power transmitted in the frequency band(s) in
which the radio equipment operates:
4.30 dBm (E.I.R.P.)
For the customers in Europe
Bulgarian С настоящето Сони Корпорация декларира, че VPL-VZ1000
отговаря на основните изисквания и другите съответстващи
клаузи на Директива 1999/5/ЕС.
Подробности може да намерите на Интернет страницата :
http://www.compliance.sony.de/.
Croatian Ovime Sony Corporation izjavljuje da je VPL-VZ1000 u skladu s
osnovnim zahtjevima i ostalim relevantnim odredbama direktive
1999/5/EZ.
Dodatne informacije potražite na sljedećoj internet adresi:
http://www.compliance.sony.de/
Czech Sony Corporation tímto prohlašuje, že tento VPL-VZ1000 je ve
shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Podrobnosti lze získat na následující URL:
http://www.compliance.sony.de/
Danish Undertegnede Sony Corporation erklærer herved, at følgende
udstyr VPL-VZ1000 overholder de væsentlige krav og øvrige
relevante krav i direktiv 1999/5/EF.
For yderligere information gå ind på følgende hjemmeside:
http://www.compliance.sony.de/
Dutch Hierbij verklaart Sony Corporation dat het toestel VPL-VZ1000 in
overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG.
Nadere informatie kunt u vinden op:
http://www.compliance.sony.de/
English Hereby, Sony Corporation, declares that VPL-VZ1000 is in
compliance with the essential requirements and other relevant
provisions of the Directive 1999/5/EC.
For details, please access the following URL :
http://www.compliance.sony.de/
Estonian Sony Corporation kinnitab käesolevaga seadme VPL-VZ1000
vastavust 1999/5/EÜ direktiivi põhinõuetele ja nimetatud
direktiivist tulenevatele teistele asjakohastele sätetele.
Üksikasjalikum info: http://www.compliance.sony.de/.
Finnish Sony Corporation vakuuttaa täten että VPL-VZ1000 tyyppinen
laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Halutessasi lisätietoja, käy osoitteessa:
http://www.compliance.sony.de/
Greek Με την παρούσα η Sony Corporation δηλώνει ότι VPL-VZ1000
συμμορφώνεται προς της ουσιώδεις απαιτήσεις και τις λοιπές
σχετικές διατάξεις της οδηγίας 1999/5/ΕΚ.
Για λεπτομέρειες παρακαλούμε όπως ελένξετε την ακόλουθη
σελίδα του διαδικτύου: http://www.compliance.sony.de/
Hungarian Alulírott, Sony Corporation nyilatkozom, hogy a(z) VPL-VZ1000
megfelel a vonatkozó alapvető követelményeknek és az 1999/5/
EC irányelv egyéb előírásainak.
További információkat a következő weboldalon találhat:
http://www.compliance.sony.de/
Before operating the unit, please read this manual thoroughly and retain it for future
reference.
Laser emission port
LABEL (for service personnel)
Latvian Ar šo Sony Corporation deklarē, ka VPL-VZ1000 atbilst Direktīvas
1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem
noteikumiem.
Plašāka informācija ir pieejama: http://www.compliance.sony.de/
Lithuanian Šiuo Sony Corporation deklaruoja, kad šis VPL-VZ1000 atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Susipažinti su visu atitikties deklaracijos turiniu Jūs galite
interneto tinklalapyje: http://www.compliance.sony.de/
Norwegian Sony Corporation erklærer herved at VPL-VZ1000 er i samsvar
med de grunnleggende krav og øvrige relevante krav i direktiv
1999/5/EF.
For flere detaljer, vennligst se: http://www.compliance.sony.de/
Polish Niniejszym Sony Corporation oświadcza, że VPL-VZ1000 jest
zgodne z zasadniczymi wymaganiami oraz innymi stosownymi
postanowieniami Dyrektywy 1999/5/WE.
Szczegółowe informacje znaleźć można pod następującym
adresem URL: http://www.compliance.sony.de/
Portuguese Sony Corporation declara que este VPL-VZ1000 está conforme
com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Para mais informacoes, por favor consulte a seguinte URL:
http://www.compliance.sony.de/
Romanian Prin prezenta, Sony Corporation declară că VPL-VZ1000 respectă
cerinţele esenţiale şi este în conformitate cu prevederile
Directivei 1999/5/EC.
Pentru detalii, vă rugăm accesaţi următoarea adresă:
http://www.compliance.sony.de/
Slovak Sony Corporation týmto vyhlasuje, že VPL-VZ1000 spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Podrobnosti získate na nasledovnej webovej adrese:
http://www.compliance.sony.de/
Slovenian Sony Corporation izjavlja, da je ta VPL-VZ1000 v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Za podrobnosti vas naprošamo, če pogledate na URL:
http://www.compliance.sony.de/
Swedish Härmed intygar Sony Corporation att VPL-VZ1000 står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
För ytterligare information gå in på följande hemsida:
http://www.compliance.sony.de/
Turkish Sony Corporation, VPL-VZ1000 ürünü için gerekli tüm testleri
1999/5/EC Direktifine gore yapmış bulunmaktadir.
Daha detaylı bilgi için lütfen web sayfasını ziyaret ediniz:
URL: http://www.compliance.sony.de/
For the customers in Korea
For the Customers in Brazil only
Apenas para clientes no Brasil
DESCARTE DE PILHAS E BATERIAS
Pilhas e Baterias não recarregáveis
Atenção:
Verifique as instruções de uso do aparelho certificando-se de que as polaridades
(+) e (-) estão no sentido indicado. As pilhas poderão vazar ou explodir se as
polaridades forem invertidas, expostas ao fogo, desmontadas ou recarregadas.
Evite misturar com pilhas de outro tipo ou com pilhas usadas, transportá-las ou
armazená-las soltas, pois aumenta o risco de vazamento.
Retire as pilhas caso o aparelho não esteja sendo utilizado, para evitar possíveis
danos na eventualidade de ocorrer vazamento.
As pilhas devem ser armazenadas em local seco e ventilado.
No caso de vazamento da pilha, evite o contato com a mesma. Lave qualquer
parte do corpo afetado com água abundante. Ocorrendo irritação, procure
auxílio médico.
Não remova o invólucro da pilha.
Mantenha fora do alcance das crianças. Em caso de ingestão procure auxílio
médico imediatamente.
Türkyedek müşterler çn
AEEE Yönetmelğne Uygundur
For the customers in the U.S.A.
SONY LIMITED WARRANTY - Please visit http://www.sony.com/psa/warranty
for important information and complete terms and conditions of Sony’s limited
warranty applicable to this product.
For the customers in Canada
SONY LIMITED WARRANTY - Please visit http://www.sonybiz.ca/pro/lang/en/
ca/article/resources-warranty for important information and complete terms
and conditions of Sony’s limited warranty applicable to this product.
For the customers in Europe
Sony Professional Solutions Europe - Standard Warranty and Exceptions on
Standard Warranty.
Please visit http://www.pro.sony.eu/warranty for important information and
complete terms and conditions.
For the customers in Korea
SONY LIMITED WARRANTY - Please visit http://bpeng.sony.co.kr/handler/
BPAS-Start for important information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
Precautions
On safety
Check that the operating voltage of your unit is identical with the voltage of
your local power supply.
Should any liquid or solid object fall into the cabinet, unplug the unit and have
it checked by qualified personnel before operating it further.
Unplug the unit from the wall outlet if it is not to be used for several days.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
The wall outlet should be near the unit and easily accessible.
The unit is not disconnected to the AC power source (mains) as long as it is
connected to the wall outlet, even if the unit itself has been turned off.
Do not look into the lens while in use.
Do not place your hand or objects near the ventilation holes. The air coming
out is hot.
On preventing internal heat build-up
After you turn off the power with the / (On/Standby) button, do not
disconnect the unit from the wall outlet while the cooling fan is still running.
Caution
This unit is equipped with ventilation holes (intake/exhaust). Do not block or
place anything near these holes, or internal heat build-up may occur, causing
picture degradation or damage to the unit.
On repacking
Save the original shipping carton and packing material; they will come in handy
if you ever have to ship your unit. For maximum protection, repack your unit as it
was originally packed at the factory.
On watching 3D video images
Safety precautions
You should only use the 3D glasses for watching 3D video images.
If you observe flickering or flashing, turn off the lighting in the room.
Not for use by children without proper adult supervision.
Be careful not to pinch your fingers in hinges of the 3D glasses when bending
the temple frames.
Do not drop or modify these 3D glasses.
If these glasses are broken, keep broken pieces away from your mouth or eyes.
On inspection of light source related parts
Since the unit uses a laser, when performing maintenance or inspection of light
source related parts, particular attention and a safe environment are necessary.
Be sure to consult with qualified Sony personnel (charged).
On LCD Projector
The LCD projector is manufactured using high-precision technology. You may,
however, see tiny black points and/or bright points (red, blue, or green) that
continuously appear on the LCD projector. This is a normal result of the
manufacturing process and does not indicate a malfunction.
Also, when you use multiple LCD projectors to project onto a screen, even if they
are of the same model, the color reproduction among projectors may vary, since
color balance may be set differently from one projector to the next.
On condensation
If the room temperature where the projector is installed changes rapidly, or if the
projector is moved suddenly from a cold to a warm place, condensation in the
projector may occur. As the condensation may cause malfunction, be careful in
adjusting temperature settings of the air conditioner. If condensation occurs,
leave the projector turned on for about two hours before use.
Notes on security
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND RESULTING FROM A
FAILURE TO IMPLEMENT PROPER SECURITY MEASURES ON TRANSMISSION
DEVICES, UNAVOIDABLE DATA LEAKS RESULTING FROM TRANSMISSION
SPECIFICATIONS, OR SECURITY PROBLEMS OF ANY KIND.
Depending on the operating environment, unauthorized third parties on the
network may be able to access the unit. When connecting the unit to the
network, be sure to confirm that the network is protected securely.
From a safety standpoint, when using the unit connected with the network, it
is strongly recommended to access the Control window via a Web browser
and change the access limitation settings from the factory preset values (refer
to “Network Features in the Operating Instructions).
Changing the password regularly is also recommended.
Do not browse any other website in the Web browser while making settings or
after making settings. Since the login status remains in the Web browser, close
the Web browser when you complete the settings to prevent unauthorized
third parties from using the unit or harmful programs from running.
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND RESULTING FROM THE
USE OF THIS UNIT FOR PURPOSES OTHER THAN GENERAL HOME USE, EITHER
DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY.
Notes on Installation and Usage
Carrying the unit
When carrying the unit, be sure to use two or
more people - one person for each side as in the
illustration.
When holding the bottom of the unit, hold it
firmly by placing your hand under the inner part
as much as possible.
Unsuitable installation
Do not place the unit in the following situations, which may cause malfunction
or damage to the unit.
Poorly ventilated location
Leave space of more than 30 cm (11
7
/
8
inches) from the top or front of the unit.
Hot and humid
Very dusty and extremely smoky locations
The air filter will become obstructed, and this may cause a malfunction of the
unit or damage it.
Other Note
Air from air conditioners or the ventilation holes of this unit or other devices,
may cause oscillation on the projection surface. Be sure not to install this unit
in the area where the air from air conditioners or the ventilation holes of these
devices reach to the lens part of this unit.
If there is debris, sand, etc. in the legs of the unit, the floor may be damaged.
Unsuitable Conditions
Do not do any of the following while using the unit.
Blocking the ventilation holes (intake or exhaust)
Ventilation holes
(exhaust)
Ventilation holes
(intake)
Tilting front/rear and left/right
If the unit is installed with inclining back and forth, the picture shape on the
projection surface is trapezoidal. Install the unit so that the unit and projection
surface are arranged in parallel.
When installing the unit at high altitudes
When using the unit at an altitude of
1,500 m (approx. 4,900 ft) or higher, set “High Altitude Mode” on the Setup
menu to “On”. Failing to set this mode when using the unit at high altitudes
could have adverse effects, such as reducing the reliability of certain
components.
Safety precautions for installing the unit on a ceiling
Never mount the projector on the ceiling or move it by yourself. Be sure to
consult with qualified Sony personnel (charged).
When installing the unit on a ceiling, be sure to use a safety wire, etc., to
prevent the unit from falling. Entrust the installation to an experienced
contractor or installer.
For dealers
When the projector is mounted on the ceiling, a Sony bracket or
recommended equivalent must be used for installation.
Be sure to secure the cabinet cover firmly when installing to the ceiling firmly.
Be sure to attach the strap to the side covers when attaching the side covers to
the unit.
Printed on recycled paper.
  • Page 1 1
  • Page 2 2

Sony VPL-VZ1000 Manualul proprietarului

Tip
Manualul proprietarului