Emos P56211 Manual de utilizare

2101900001_31-P56211_00_01_PRINT 85 × 130 mm

P56211

GB Wireless Thermostat

CZ Bezdrátový termostat

SK Bezdrôtový termostat

PL Bezprzewodowy termostat

HU Vezeték nélküli termosztát

SI Brezžični termostat

RS|HR|BA|ME Bežični termostat

DE Funk-Thermostat

UA Бездротовий термостат

RO|MD Termostat fără r

LT Belaidis termostatas

LV Bezvadu termostats

EE Juhtmevaba termostaat

BG Безжичен термостат

FR Thermostat sans l

IT Termostato senza li

ES Termostato inalámbrico

NL Draadloze thermostaat

Other countries Wireless Thermostat

www.emos.eu

2

13 15

12

14

11

1

5

2

6

3.1

7

3

8

49

10

1

21

2

3

4

1

2 3

21

3 4 5

4

5

6

7

6

8

6

9

6

10

7

11

10

9

8

7

6

5

1 2 3 4

11

8

9

3

2

1

12

10 11

13

GB | Wireless Thermostat

The P56211 wireless thermostat is designed for controlling heating and air-

-conditioning systems.

Important

Before the rst use, make sure to carefully read the instruction manual for the

thermostat, as well as the manual for the boiler or air-conditioning equipment.

Turn o power supply before installing the thermostat!

Installation should be carried out by a qualied person!

Follow applicable standards during installation.

Technical specications:

Switched load: max. 230 V AC; 16 A for resistive load; 4 A for inductive load

Temperature measurement: 0 °C to 40 °C with 0.1 °C resolution; accuracy

±1 °C at 20 °C

Temperature setting: 5 °C to 35 °C in 0.5 °C increments

Temperature dierential setting: 0.2 °C to 2 °C in 0.1 °C increments

Operating temperature: 0 °C to 40 °C

Unit interconnection: via 868 MHz radio signal, 25 mW e.r.p. max.

Transmitter unit range: up to 100 m in an open space

WiFi frequency: 2.4 GHz, max. 25 mW e.i.r.p.

Power supply:

Control unit (transmitter): 5 V/1.5 A

Switching unit (receiver): 230 V AC/50 Hz

Includes: USB adapter 5 V/1.5 A, micro USB cable 1.5 m

Dimensions:

Control unit: 40 × 138 × 96 mm

Switching unit: 37 × 86 × 86 mm

Description of the Thermostat (Transmitter Unit) – Icons and Buttons

(see g. 1)

1 – day number

2 – time

3 – WiFi signal reception

3.1 – wireless communication with receiver

4 – cooling /heating mode

5 – set temperature

6 – menu lock

7 – holiday mode

8 – temporary change of temperature

9 – HOLD mode

10 – current room temperature

11 – programme settings

12 – data and time settings

13 – function selection, conrmation

14 – temporary change of temperature; navigation in the settings

15 – return to main menu

14

Thermostat Stand (see g. 2)

1 – micro USB socket for connecting the power cable

2 – r emoving the thermostat from the stand (start with the bottom of the

thermostat rst)

Description of the Receiver (Switching Unit) (see g. 3)

1 – main switch

position – o

position – on

2 – M/A button (red LED)

3 – MANUAL button (green LED)

Procedure for Removing the Front of the Switching Unit (see g. 4)

2, 3 – Use a screwdriver to press down and hold the inner lock, remove the

front cover.

4, 5 – Connect the wires to the labelled terminals according to the wiring

diagram, click the cover back in place.

Mobile Application

The thermostat can be controlled using a mobile application for iOS or Android.

Download the EMOS GoSmart app for your device.

QR code for downloading the Android app

QR code for downloading the iOS app

Description of Registering and Logging into the Application (see g. 5)

To use the mobile application, you must rst register by tapping the Sign Up button.

Enter your country and e-mail address, check o your consent with the end user

licence agreement and tap Get Verication Code.

Enter the verication code sent to your e-mail.

Then, set the password for your account and tap Done.

Choose whether you want to enable Data Analysis/Personalisation and tap Go

to App.

Connecting the Thermostat to a Wi-Fi network for Control via the

Mobile App (see g. 6)

Tap Add Device in the app and enable location access.

Choose add manually and select Small Home Appliances – Thermostat (Wi-Fi)

or Others – Others (Wi-Fi).

15

Select a 2.4 GHz Wi-Fi network, enter the password and tap Next.

Check o Conrm that the indicator is ashing rapidly and tap Next.

The chosen thermostat should appear in the app within 2 minutes.

Tap the green arrow on the right; the thermostat will be added into the app.

Then tap the thermostat icon in the app to open the main control menu.

Note:

If the thermostat fails to pair, repeat the process.

5 GHz Wi-Fi networks are not supported.

The thermostat can only be controlled via the app by 1 user at a time. If another

user wants to control the thermostat, the previous user must log out.

Description of the Main Menu of the Mobile App (see g. 7)

Tap the thermostat icon in the app to open the main control menu.

1. Thermostat status (ON/OFF) – Anti-freeze mode, temperature xed to 5 °C

2. Work mode setting (detailed information in the WORK MODES chapter of

this manual)

Automatic

Manual – see HOLD mode

Temporary – see Temporary change mode

Boost – see Timed temporary change mode

Holiday – see Holiday mode

3. Schedule (see g. 8)

1 – add a time period

2 – delete a time period

3 – day display

7 days (Mon → Sun)

5+2 days (Mon → Fri + Sat → Sun)

24-hour

Every day can be divided into a maximum of 6 periods.

When in 7 day mode, you can copy the temperature settings from one day into

other days (see g. 9).

Example:

Long-press the Thursday icon; a menu of other days will open. Mark them orange

by tapping them and conrm.

Thursday‘s schedule will copy over to Monday, Tuesday and Wednesday.

4. Setting (see g. 10)

1 – reset the thermostat to factory settings

2 – key lock

3 – correction of ambient temperature (-3 °C to +3 °C in 0.5 °C increments)

4 – heating/cooling system mode

5 – calendar mode (7 days, 5+2, 24 h)

5. Thermostat mode icon

heating

cooling

o

16

6. Work mode icon

7. Adjust temperature

8. Current room temperature

9. Current set temperature

10. Adjust temperature

11. Network information about the device, change the name in the app,

location information, add an icon to the home screen and other similar

settings

Deleting the Thermostat from the App (see g. 11)

Long-press the thermostat icon, check o the thermostat and tap the dustbin

icon to delete the thermostat.

User Overview/Password Change/App Update

Tap the icon in the bottom right and then the icon in the top right.

This will open a new menu with settings.

INSTALLATION

Attention:

Before changing the thermostat, disconnect the heating system from the mains

power in your home. This will prevent potential injury by electric current.

Installing the Thermostat (see g. 2)

Place the thermostat in the stand included in the pack.

Connect the USB power supply (included) with the connected micro USB cable

to 230 V mains.

Plug the micro USB cable into the bottom of the stand.

Placement of the Thermostat

The placement of the thermostat (transmitter unit) signicantly aects its

functioning.

Choose a location where members of the family spend most of their time,

preferably near an inside wall where air circulates freely, with no direct sunlight.

Do not place the thermostat in the vicinity of heat sources (such as TV sets, radi-

ators, fridges), or close to a door. Failure to comply with these recommendations

will prevent proper control over room temperature.

Switching Unit Wiring Diagram

Pump/Motorised Valve Connection Diagram

Pump/

valve

17

Floor Heating Connection Diagram

Connected

device

Boiler Connection Diagram

Boiler

• The pre-installed wire coupler will not be connected.

Expansion Valve/Electric Drive Connection Diagram

Connected

device

PUTTING THE DEVICE INTO OPERATION

Pairing the Control Unit with the Switching Unit

Both thermostat units must be paired before rst use.

Pairing enables transmission of information between the control unit and the

switching unit.

Setting is done via automated pairing (self-learning).

1. Fit the thermostat gently onto the stand.

Connect the USB power supply with micro USB cable to 230 V mains and

plug the cable into the stand.

2. Correctly connect the switching unit to voltage supply, turn the main switch

to the position and long press (for at least 10 seconds) the M/A button; a

green LED will begin ashing on the MANUAL button.

3. Long-press the and buttons on the thermostat (transmitter) for about

5 seconds; the icon will start ashing.

Both units will be paired within 1 minute and the green diode on the switching

unit will stop ashing.

18

If you want to change the pairing code of the two units or the thermostat does

not function properly, repeat the entire pairing procedure from step 1 – the pairing

code will be rewritten automatically.

Testing Wireless Communication between the Units

1. Use the button on the thermostat or use the app to set a temperature

several degrees higher than the current room temperature.

2. The red LED on the switching unit will light up.

3. If the LED does not light up, move the control unit closer to the switching unit.

The maximum range between the control and switching unit is 100 m in an

open space.

The range may decrease indoors as the signal has to pass through walls and

other obstacles.

Main Switch

To turn on the switching unit, set the switch to the position.

If the heating system is not used for an extended period of time, it is recommen-

ded to turn the switching unit o (switch the main switch to the position).

LED Indicators

Automated Mode

In automated mode, a red LED will glow when the thermostat switches on the

output relay.

Manual Mode

Press the MANUAL button; a green LED will light up.

The receiver will switch to manual mode and will not respond to commands

from the thermostat.

To switch on the output relay (turn on the connected device), press the M/A

button; a red LED will light up on it.

To turn o manual mode, press the MANUAL button again; the green LED will

switch o.

Setting the Clock, Calendar

Press the button; the values will start ashing.

Use the buttons to set the following values (holding the button down

accelerates the value change):

Day – Month – Year – Hour – Minute.

Conrm the set value by pressing .

To end setting, press the button or wait 30 seconds.

After setting is complete, the current day number will be displayed:

1 – Monday

2 – Tuesday

3 – Wednesday

4 – Thursday

5 – Friday

6 – Saturday

7 – Sunday

19

WORK MODES

Holiday Mode

Sets a constant temperature for an extended period of time.

Long-press (5 seconds) the button; the time value will start ashing.

Release the button and press it again for 5 seconds.

The icon will appear and the number of days will start ashing.

Repeatedly press the button to set the number of days (from 1 to 99).

Conrm the set number of days by pressing ; the temperature value will

begin ashing.

Repeatedly press the button to set the temperature.

Conrm by pressing ; the icon will appear.

If you want to go back and change the temperature for holiday mode, press the

button repeatedly.

You can cancel holiday mode by pressing or .

Temporary Change Mode

Short-term manual change of temperature.

While in Auto mode, use the buttons to change the temperature setting;

the value will be saved automatically.

The icon will appear.

This mode will be automatically cancelled by the rst programmed temperature

change (the time remaining until the change + clock will be alternating in the top

left corner) or it can be cancelled manually by pressing .

OFF Mode

Anti-freeze mode, temperature xed to 5 °C.

While in Auto mode, press the button 2×; a temperature of 5 °C will appear

in the top right corner.

To cancel the mode, press .

Timed Temporary Change Mode

Temporary manual change in temperature for 1 to 9 hours.

While in Auto mode, long-press the button; the time setting will start ashing

in the top left corner.

Use the buttons to set the duration of the temperature change, from 1 to

9 hours, with 1 h resolution.

Conrm by pressing . Then set the temperature of choice using the

buttons.

The remaining set time + the clock will be alternating in the top left corner; you

can cancel the mode prematurely by pressing .

HOLD Mode

Permanent manual temperature change.

While in Auto mode, press the button; the HOLD will appear in the bottom right.

Set the temperature of choice using the buttons; the value will be saved

automatically.

The set temperature will be maintained until HOLD mode is cancelled.

Any programmed temperature change will not be carried out.

To cancel HOLD mode, press .

20

Heating Programme Setting Mode

Sets temperature over the course of the whole day (6 temperature changes

in the day).

Press the PRG button. The day number will start ashing (1–7 = Monday to

Sunday).

Press repeatedly to select the days of choice.

Dierent each day programme – the number of the selected day ashes

Monday to Friday programme – ashes

Saturday to Sunday programme – ashes

All week programme – ashes

Select your programme of choice and conrm with .

The time of the rst temperature change will be ashing; you can set the time

by repeatedly pressing (10 minute increments), then conrm with .

The temperature value will begin ashing; set by repeatedly pressing .

P1 will appear below the set temperature, indicating the 1st temperature

change in the day.

Conrm by pressing . Continue by setting the start of the second temperature

change (P2 will appear under the temperature).

Set the time and temperature by following the same steps as when setting the

1st temperature change.

Continue the process until all 6 temperature changes (P1 to P6) are set.

Factory pre-set times and temperatures are as follows:

Monday to Friday

Temperature change Time Temperature

P1 6:30 20 °C

P2 8:30 16 °C

P3 12:00 16 °C

P4 14:00 16 °C

P5 16:30 21 °C

P6 22:30 7 °C

Saturday to Sunday

Temperature change Time Temperature

P1 7:30 20 °C

P2 9:30 20 °C

P3 11:30 20 °C

P4 13:30 20 °C

P5 16:30 20 °C

P6 22:30 15 °C

Pagina se încarcă ...

Emos P56211 Manual de utilizare

Emos P56211 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente