Heinner HWDM-H10614A Manualul proprietarului

WASHER DRYER

Model: HWDM-H9614A

• Washer dryer

• Energy class: A

• Spin: 1400rpm

www.heinner.com

I.

INTRODUCTION

Before using the appliance, please carefully read this instruction manual and keep it for future

reference.

This instruction manual is designed to provide you with all required instructions related to the

installation, use and maintenance of the appliance.

In order to operate the unit correctly and safety, please read this instruction manual carefully before

installation and usage.

II.

CONTENT OF YOUR PACKAGE

➢ Washer dryer

➢ User manual

➢ Warranty card

Thank you for purchasing this product!

www.heinner.com

• The manufacturer reserves the right for any modifications on the product which might

be deemed necessary or useful without informing about it in this IFU.

• Before operating your new washing machine, please read this instruction carefully,

and keep it for future reference. If you have lost it accidentally, ask customer service

for e-copy or hard copy.

• Please make sure the socket is grounded securely, the water source connection is

reliable.

• This appliance is not to be used by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

• This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by children without

supervision.

• Children should be supervised to ensure that they do not play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

• The new hose sets supplied with the appliance are to be used and that old hose sets

should not be reused.

• For appliances with ventilation openings in the base, that a carpet must not obstruct

the openings.

• Children of less than 3 years should be kept away unless continuously supervised.

• The maximum permissible inlet water pressure, 1 MPa, for appliances intended to be

connected to the water mains. The minimum permissible inlet water pressure, 0.1

MPa, if this is necessary for the correct operation of the appliance.

• WARNING: The appliance must not be supplied through an external switching device,

such as a timer, or connected to a circuit that is regularly switched on and off by the

utility.

• The tumble dryer is not to be used if industrial chemicals have been used for cleaning.

• Lint must not to be allowed to accumulate around the tumble dryer (not applicable

for appliances intended to be vented to the exterior of the building).

• Adequate ventilation must be provided to avoid the back flow of gases into the room

from appliances burning other fuels, including open fires.

• Do not dry unwashed items in the tumble dryer.

III.

SAFETY PRECAUTIONS

www.heinner.com

• Items that have been soiled with substances such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine, waxes and wax removers should be

washed in hot water with an extra amount of detergent before being dried in the

tumble dryer.

• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber

backed articles and clothes, or pillows fitted with foam rubber pads should not be

dried in the tumble dryer.

• Fabric softeners, or similar products, should be used as specified by the fabric softener

instructions.

• Remove all objects from pockets such as lighters and matches.

• WARNING: Never stop a tumble dryer before the end of the drying cycle unless all

items are quickly removed and spread out so that the heat is dissipated.

• The appliance must not be installed behind a lockable door, a sliding door or a door

with a hinge on the opposite side to that of the tumble dryer, in such a way that a full

opening of the tumble dryer door is restricted.

• The maximum drying capacity is k6g.

• The maximum washing capacity is 9kg.

• For private domestic use only.

• This appliance is intended to be used in household and similar applications such as:

staff kitchen areas in shops, offices and other working environments.

farmhouses.

by clients in hotels, motels and other residential type environments.

bed and breakfast type environments.

areas for communal use in blocks of flats or in launderettes.

Before using the washing machine

1. Removing the packaging and inspection

• After unpacking, ensure that the washing machine is undamaged. If in doubt, do not

use the washing machine. Contact authorized service or local retailer.

• Check that the accessories and supplied parts are all present.

• Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of

children, as they are potentially dangerous.

2. Remove the transport bolts

• The washing machine is fitted with transport bolts to avoid a possible damage to the

interior during transport. Before using the machine, it is imperative that the transport

bolts are removed.

• After their removal, cover the openings with the 4 enclosed plastic caps.

3. Install the washing machine

• Move the appliance without lifting it by the worktop.

• Install the appliance on a solid and level floor surface, preferably in a corner of the

room.

www.heinner.com

• Ensure that all four feet are stable and resting on the floor and then check that the

washing machine is perfectly level (use a spirit level).

• Ensure that the ventilation openings in the base of the washing machine (if available

on your model) are not obstructed by a carpet or other material.

4. Water inlet

• Connect the water supply inlet hose in accordance with the regulations of your local

water company.

• Water inlet – depending on models

Single inlet – cold water only

Dual inlet – Hot and cold water

• Water tap: ¾ threaded hose connector.

5. Drain

• Connect the drain hose to the siphon or hook it over the edge of a sink by means of

the "U" bend supplied.

• If the washing machine is connected to an integrated drainage system, ensure that

the latter is equipped with a vent to avoid simultaneous loading and draining of

water (siphoning effect).

• Fix the drain hose securely to prevent scalding during machine drainage.

6. Electrical connection

• Electrical connections must be carried out by a qualified technician in compliance

with the manufacturer's instructions and current standard safety regulations.

• Data regarding voltage, power consumption and protection requirements is given on

the inside of the door.

• The appliance must be connected to the mains by means of a socket with an earth

connection in accordance with current regulations. The washing machine must be

earthed by law. The manufacturer declines all liability for damage to property or

injury to persons or animals due to non-compliance with the directions given above.

• Do not use extension leads or multiple sockets. Make sure the capacity of the socket

is powerful enough to drive the machine during heating.

• Before any maintenance on the washing machine disconnect it from the mains

supply.

• After installation, access to the mains plug or to disconnection from the mains supply

must be ensured at all times via a double-pole switch.

• Do not operate the washing machine if it has been damaged during transport. Inform

the local dealer.

• Mains cable replacement is only to be carried out by authorized service.

• The appliance must only be used in the household for the prescribed uses.

www.heinner.com

Precautions and general recommendations

1. Packaging

• The packaging material is entirely recyclable and marked with the recycling symbol

. Adhere to current local regulations when disposing of packaging material.

2. Disposing of packaging and scrapping old washing machines

• The washing machine is built from reusable materials. It must be disposed of in

compliance with current local waste disposal regulations.

• Before scrapping, remove all detergents residues, break the door hook, and cut off

the power cable so that the washing machine is made unusable.

• This appliance is marked according to the European directive on Waste is

Electrical and Electronic Equipment (WEEE). By ensuring that this product disposed

of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate

waste handling of this product. The symbol on the product, or on the documents

accompanying the product, indicates that this appliance may not be treated as

household waste. Instead it shall be handed over to the applicable collection point

for their cycling of electrical and electronic equipment. Disposal must be carried out

in accordance with local environmental regulations for waste disposal. For more

detailed information about treatment, recovery and recycling of this product, please

contact your local city office, your household waste disposal service or the shop

where you purchased the product.

3. Location and surroundings

• The washing machine must only be installed in enclosed spaces. Installation in the

bathroom or other places where air is humid is not recommended.

• Do not store flammable fluids near the appliance.

4. Safety

• Do not leave the appliance plugged in when not in use. Never plug or unplug the

power from the mains supply, if your hands are wet.

• Turn off the tap.

• Before any cleaning and maintenance, switch off the machine and disconnect it from

the mains.

• Clean the outside of the washing machine with a damp cloth. Do not use abrasive

detergents.

• Never open the door forcibly or use it as a step.

www.heinner.com

IV.

OPERATING THE APPLIANCE

Emergency door opening

In case of failure to open the door due to power outage or other special circumstances, the

door lock lever at the drainage pump door can be used for emergency opening.

Note:

1. Do not operate when the machine is working normally.

2. Before operation, please make sure that the inner barrel has stopped turning, without high

temperature, and the water level is lower than the clothing inlet. If the water level is

higher than the clothing inlet, drain off water through the drain away pipe (if available)

or by slowly unscrewing the filter.

3. Operation method: Open the cover of drainage pump door, pull down the lock lever with

the help of a tool, and then the door can be opened (indicated in the figure).

Door lock lever

Before the first wash cycle

To remove any residual water used during testing by the manufacturer, we recommend that

you carry out a short wash cycle without laundry.

1. Open the tap.

2. Close the door.

3. Pour a little detergent (about 30 ml) into the main wash chamber of the detergent

dispenser.

4. Select and start a short program (see separate quick reference guide).

Preparation of the washing machine

1. Sort the laundry according to:

• Type of fabric I care label symbol

Cottons, mixed fibres, easy care synthetics, wool, handwash items. The wool wash

cycle of this machine has been tested and approved by The Woolmark Company for

the washing of Woolmark garments labelled as "machine wash" provided that the

garments are washed according to the instructions on the garment label and those

issued by the manufacturer of this washing machine.

• Color

Separate colored and white items. Wash new colored articles separately.

• Loading

Wash items of different sizes in the same load to improve washing efficiency and

distribution in the drum.

www.heinner.com

• Delicates

Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras) in

a cloth bag or pillowcase with zip. Always remove curtain rings or wash curtains with

the rings inside a cotton bag.

2. Empty all pockets

Coins, safety pins etc. can damage your laundry as well as the appliance drum and tub.

3. Fasteners

Close zips and fasten buttons or hooks; loose belts or ribbons should be tied together.

Stain removal

Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the program.

• Pre-treat heavily soiled areas with stain remover if necessary.

Dyeing

1. Open the door.

2. Load the articles one at a time loosely into the drum, without overfilling. Observe the load

sizes given in the quick reference guide.

Note: Overloading the machine will result in unsatisfactory washing results and creased

laundry.

3. Close the door.

Detergents and additives

Always use high efficiency, low foam detergent for a front load machine.

The choice of detergent depends on:

• type of fabric (cottons, easy care/synthetics, delicate items, wool). Note: Use only

specific detergents for washing wool

• color

• the wash temperature

• degree and type of soiling

www.heinner.com

Remarks:

Any whitish residues on dark fabrics are caused by insoluble compounds used in modern

phosphate free powder detergents. If this occurs, shake or brush out the fabric or use liquid

detergents. Use only detergents and additives specifically produced for domestic washing

machines. When using descaling agents, dyes or bleaches for the pre-wash, make sure that

they are suitable for use in domestic washing machines. Descales could contain products

which could damage your washing machine. Do not use any solvents (e.g. turpentine,

benzine). Do not wash fabrics that have been treated with solvents or flammable liquids.

Dosage

Follow the dosage recommendations on the detergent pack. They depend on:

• degree and type of soiling

• size of wash

follow the detergent manufacturer's instructions for a full load;

half load: 3/4 the amount used for a full load;

minimum load (about 1 kg): 1/2 the amount used for a full load.

• water hardness in your area (ask for information from your water company). Soft

water requires less detergent than hard water.

Notes:

Too much detergent can result in excess foam formation, which reduces washing efficiency. If

the washing machine detects too much foam, it may prevent spinning. Insufficient detergent

may result in grey laundry in time and also calcifies the heating system, drum and hoses.

Where to put detergent and additives

The detergent drawer has three chambers.

Prewash chamber

Detergent for the prewash I soak.

www.heinner.com

Main wash chamber

• Detergent for the main wash

• Stain remover

• Water softener (water hardness class 4)

Softener chamber

• Fabric softener

Notes:

• Keep detergents and additives in a safe, dry place out of the reach of children.

• Liquid detergents can be used for programs with prewash. However, in this case a

powder detergent must be used for the main wash.

• Do not use liquid detergents when activating the "Start Delay" function

• To prevent dispensing problems when using highly concentrated powder and liquid

detergents, use the special detergent ball or bag supplied with the detergent and

place it directly inside the drum.

• When using descaling agents, bleaches or dyes, make sure that they are suitable for

washing machines. Descalers could contain compounds that can damage parts of your

washing machine.

• Do not use any solvents in the washing machine (ex. turpentine, benzine).

www.heinner.com

1

Worktop

2

Control panel

3

Detergent dispenser

4

Door

5

Plinth covering pump access

6

Adjustable feet

V. PRODUCT DESCRIPTION

www.heinner.com

• Read this "INSTALLATION GUIDE" before operating.

• Keep this "INSTALLATION GUIDE" for future reference.

• Read the general recommendations about disposing of packaging in the INSTRUCTION

FOR USE.

Parts supplied

• Package with small items

• User manual & Warranty card

• 4 plastic caps

• Inlet hose (inside the machine or already installed)

• “U”bend (inside the machine or already installed)

VI. INSTALLATION

www.heinner.com

Before using the washer, remove the transport bolts

Important: Transport bolts which are not removed can cause damage to the appliance.

1. Screw off all transportation bolts for approx. 30mm with wrench following the direction of

arrow shown (not fully screw it off).

2. Push four transportation bolts on horizontal direction inward and loose transportation

bolt.

3. Pull out transportation bolt together with rubber part and plastic part.

4. To ensure safety and reduce noise, you should install the transportation bolt cover supplied

with the unit (see the annex accompanying the unit). Lean and place the transportation bolt

into hole and press it following the shown direction until it clicks.

Important: Keep the transport bolts for future transporting of the appliance and in this case

refit the transport bolts in reverse order.

www.heinner.com

Adjustment of the feet

The appliance must be installed on a solid and level floor surface (if necessary, use a spirit

level). If the appliance is to be installed on a wooden floor, distribute the weight by placing

it on a 60x60cm sheet of plywood at least 3cm in thickness and secure it to the floor. If the

floor is uneven, adjust the 4 leveling feet as required; do not insert pieces of wood etc. under

the feet.

1. Slacken the locknut clockwise (see arrow) using a wrench.

2. Lift the machine slightly and adjust the height of the foot by revolving it.

Lower

Higher

Important: Tighten the locknut by turning it anti-clockwise towards the appliance casing.

max. 20 mm

www.heinner.com

INSTALL BOTTOM COVER

To realize quieter operation, a bottom cover is supplied with the unit (only applies to some

of the Hisense washers). After installing the cover at the bottom of the washer, the noise

level will be greatly reduced. Please ask for advice from specialists before installing the

cover, nevertheless, the machine can be used without the bottom cover

Noise-Reduction Bottom Plate Installation Instructions

Stick acoustic wool to the side of bottom cover plate with the letter of “PUMP”. Tilt the

washer by 30°-40°, when installing the bottom cover, please face the side with sound

insulation upwards and attach 'PUMP' at the corner of the cover to the position of the pump

in the washer.

Before installing the noise-reduction bottom plate, align and paste the acoustic absorption

wool with and along the right-angle impression on bottom plate (this procedure is

unnecessary for some of the models without acoustic absorption wool). (Pic 1)

Remove surface paper on double sided tape at four sides of the bottom plate. (Pic 2)

Incline the machine to an angle of 40° and let the side with right-angle notch face towards

front of the washing machine, as shown in the figure. Insert the side with oblique-angle

notch between two-foot screws at back of the washing machine completely in place. Then,

install the bottom plate and ensure that it contacts with bottom of the washing machine

closely. (Pic 3)

Press the double-sided tape on four sides manually to secure the noise-reduction plate to

the machine body firmly (pic 4)

www.heinner.com

Press the double-sided tape on four sides manually to secure the noise-reduction plate to the

machine body firmly.

Connect the water supply inlet hose.

If the water inlet hose is not already installed, it must be screwed to the appliance. The blue

marked hose is only for cold water. Depending on the model, the hot water hose marked with

red should also be connected, for models having dual inlets.

Hot (depending on models) Cold

Screw by hand the inlet hose onto the tap, tightening the nut.

Attention:

• No kinks in the hose

• The appliance must not be connected to the mixing tap of an unpressurized water

heater.

• Check water tightness of connections by turning the tap completely on.

• If the hose is too short, replace it with a suitable length or pressure resistant hose

(1000 kPa min)

• Check the inlet hose regularly for brittleness and cracks and replace if necessary.

• The washing machine can be connected without a non-return valve.

Connect the drain hose

In case the drain hose is installed as shown below:

Unhook it only from the right clip (see arrow)

www.heinner.com

Connect the drain hose to the drain or hook it over the edge of a sink by means of the "U"

bend.

Fit the "U" bend E, if not already installed, at the end of the drain hose.

Notes:

• Ensure that there are no kinks in the drain hose.

• Secure the hose so that it cannot fall down. After wash phase, machine will drain out

hot water.

• Small hand basins are not suitable.

• To make an extension use a hose of the same type and secure the connections with

clips.

• Max. overall drain hose length: 2.50 m

Transport/Handing

Never lift the appliance by the worktop when transporting.

• Pull out the mains plug.

• Turn off the tap.

• Disconnect the inlet and drain hoses.

• Eliminate all water from the hoses and from the appliance (see "Removing the Filter",

"Draining Residual Water")

• Fit the transport bolts (obligatory)

• The machine is over 55 kg in weight, two persons are needed to move it.

Electrical connection

Only use a socket with an earth connection.

• Do not use extension leads or multi sockets.

• Electric supply must be adequate for the machine's 10 A Current Rating.

• Electrical connections must be made in accordance with local regulations.

• The electrical power cable must be replaced exclusively by a licensed electrician.

www.heinner.com

A. Program selector

B. Stat/pause button

C. Program and fuction status display window

D. Delay end button

E. Dry level button

F. Option button

G. Spin button

H. Temp button

VII. CONTROL PANEL & PROGRAMMES

www.heinner.com

Program

Material / Level of Soiling

Functions

Max.

Wash

Load

kg

Max.

spin

speed

rpm

Cotton

--,20ºC, 30ºC,

40ºC,

60ºC, 90ºC

Heavily and moderately soiled cotton, or linen. For very heavily soiled items select the

"Prewash" function.

W

9

1400

WD

6

1400

Synthetics

--,20ºC,30ºC,

40ºC, 60ºC

Moderately soiled synthetics, cotton blended fabrics

W

9

1400

WD

6

1400

Wool

--,20ºC,30ºC,40ºC

Machine washable wool. (Refer to the washing label attached to the clothing).

W

2

600

Quick 15'

--

,20ºC,30ºC,40ºC

Cotton, mixed fabrics. Items worn for a short time or newly bought.

W

1

800

Mix

--

,20ºC,30ºC,40ºC

Mixed loads of moderately soiled cotton and synthetic fabrics.

W

5

1400

WD

5

1400

Eco40-60

Normally soiled cotton laundry.

W

9

1400

WD

6

1400

Rinse+Spin

This program is defaulted to two rinses and spin.

W

9

1400

WD

6

1400

Spin

Select the length, and speed, of the spin manually.

S

9

1400

SD

6

1400

Cotton Dry

The wet cotton & linen clothes can be dried after being spun.

D

6

/

Synthetics Dry

The wet chemical fiber clothes can be dried after being spun.

D

5

/

Steam Refresh

It is suitable for removing the peculiar smell (such as, the smell of smoke/hot

pot/barbecue, etc.) on the clothes.

D

2

/

Wash and Dry

For cleaning normally soiled cotton items which are declared to be washable at

40 °C or 60 °C, together in the same cycle, and to dry them in such a way that it can

be immediately stored in a cupboard. This cycle is used to assess the compliance

with the EU Eco-design legislation for wash and dry.

WD

6

1400

20℃

This program is suitable for cotton clothes with light stains, energy saving.

W

9

1400

WD

6

1400

Allergy Care

60ºC, 90ºC

Program to effectively extinguish bacteria in textiles. It is appropriate for clothes of

babies who are sensitive to clothes.

W

4

1400

WD

4

1400

Drum Clean

90ºC

Program to remove dirt and bacterial residue that can breed in the machine after it

has been used for a period, especially when low temperature washes are used

regularly.

WD

0

800

Please select appropriate washing temperature according to instruction of care label attached to

clothes, if not, clothes can be damaged.

www.heinner.com

Parameter

Model No/Item No

HWDM-H9614A

Washing/drying Capacity

9/6 kg

Max. spin speed

1400 rpm

Net Weight

70 kg

Dimension (WXDXH)

595x610x845 mm

Rated Voltage

220-240 V~

Heating Power

1500 W

Washing Power

250 W

Drying Power

1350 W

Spinning Power

500 W

Load the clothes to be washed in the drum and close the door. Add the detergent into the

relevant compartments for the type of program you are going to select, add detergent as

described in Detergent and Additives section of User’s manual.

1. Turn on the power.

2. Spin program selection button to required program, “off” must be passed through if

pointer’s initial position is not “off”, start up.

3. Select washing temperature, spin speed by pressing “Temp”, “Spin” buttons.

4. Press “Options” button to select additional functions.

5. After starting the program, display window displays program length (hours: minutes) and

additional function options in sequence.

At standby state, press “Options” button to select additional function for current program.

Select only one function for each press, and then corresponding icon flashes. After starting

up, program cannot be changed.

Pre-wash

• Select the function to conduct pre-wash to enhance washing effects and better

remove stains. This function is suitable for heavy dirt clothes.

• Before inflowing, laundry detergent/ washing powder can be added to pre-wash box

and washing powder must be added to main wash box.

Extra rinse

After set the function of rinsing adding, the program runs the rinsing process once again

before running the softening, and the total running time of the program increases

accordingly.

Inlet water warning

If tap is not opened, or water pressure is over low, and display screen will prompt “F01” to

give alarm.

Pagina se încarcă ...

Heinner HWDM-H10614A Manualul proprietarului

Acest manual este potrivit și pentru

Heinner HWDM-H10614A Manualul proprietarului

Lucrări conexe

Alte documente