McCulloch M51-140WR Manualul proprietarului

M40-120 CLASSIC, M40-125 CLASSIC+, M46-120 CLASSIC,

M46-120R CLASSIC, M46-125 CLASSIC+, M46-125R CLASSIC+,

M46-140R CLASSIC+, M46-145WRP CLASSIC+, M46-150WR

CLASSIC, M51-140WR CLASSIC+, M51-150R CLASSIC,

M51-150WR CLASSIC, M53-150WR CLASSIC

EN Operator's manual 6-18

BG Ръководство за експлоатация 19-33

CS Návod k použití 34-46

DA Brugsanvisning 47-59

DE Bedienungsanweisung 60-73

EL Οδηγίες χρήσης 74-88

ES Manual de usuario 89-102

ET Kasutusjuhend 103-115

FI Käyttöohje 116-128

FR Manuel d'utilisation 129-142

HR Priručnik za korištenje 143-155

HU Használati utasítás 156-169

IT Manuale dell'operatore 170-183

LT Operatoriaus vadovas 184-196

LV Lietošanas pamācība 197-209

NL Gebruiksaanwijzing 210-223

NO Bruksanvisning 224-236

PL Instrukcja obsługi 237-250

PT Manual do utilizador 251-264

RO Instrucţiuni de utilizare 265-278

RU Руководство по эксплуатации 279-293

SK Návod na obsluhu 294-306

SL Navodila za uporabo 307-319

SV Bruksanvisning 320-332

UK Посібник користувача 333-346

21

9 9

19

20

9

1

12

13

14

15

2

18

17

16

4

5

6

7

8

9

10

11

3

1

2 3 4 5 6 7

8 9 10 11 12 13

14 15 16 17

18 19

20 21

22 23

24 25

26 27

28 29

30 31

32 33

34 35

36

Contents

Introduction...................................................................6

Safety.............................................................................7

Assembly

.......................................................................9

Operation.....................................................................10

Maintenance................................................................11

Transportation, storage and disposal...................... 13

Technical data.............................................................14

EC Declaration of Conformity....................................17

Introduction

Product description

The product is a pedestrian-controlled rotary lawn

mower. The grass is collected in a grass catcher.

Remove the grass catcher to get rear discharge of the

grass. Attach a mulch kit (accessory) to cut the grass

into fertilizer.

Intended use

Use the product to cut grass in private gardens. Do not

use the product for other tasks.

Product overview

(Fig. 1)

1. Drive bail (M46-120R CLASSIC, M46-125R

CLASSIC+, M46-150WR CLASSIC, M51-140WR

CLASSIC+, M51-150R CLASSIC, M51-150WR

CLASSIC, M53-150WR CLASSIC, M46-140R

CLASSIC+, M46-145WRP CLASSIC+)

2.

Upper handle / handlebar

3. Engine brake handle

4. Starter rope handle

5. Loop for starter rope

6. Grass catcher

7. Lower handle

8. Lower handle assembly

9. Cutting height levers

10. Oil cap

11. Muffler

12. Drain plug for carburetor bowl

13. Primer bulb

14. Spark plug

15. Fuel tank

16. Blade

17. Spring washer

18. Blade bolt

19. Cutting deck

20. Air filter

21. Operator's manual

Symbols on the product

(Fig. 2) WARNING: Careless or incorrect use can

result in injury or death to the operator or

bystanders.

(Fig. 3) Please read the operator's manual carefully

and make sure that you understand the

instructions before use.

(Fig. 4) Keep persons and animals at a safe

distance from the work area.

(Fig. 5) Stop the engine and remove the ignition

cable before repairs or maintenance.

(Fig. 6) Look out for thrown objects and ricochets.

(Fig. 7) Warning: rotating blade. Keep hands and

feet clear.

(Fig. 8) Warning: rotating parts. Keep hands and

feet clear.

(Fig. 9) This product is in accordance with

applicable EC directives

(Fig. 10) Noise emission to the environment

according to the European Community’s

Directive. The product’s emission is

specified in the Technical data chapter and

on the label.

(Fig. 11) Risk of fire.

(Fig. 12) Risk of fire.

(Fig. 13) Risk of explosion.

(Fig. 14) Always stop the engine before refueling.

(Fig. 15) Hot surface.

(Fig. 16) The exhaust fumes from the engine contain

carbon monoxide, an odourless, poisonous

and very dangerous gas. Do not run the

product indoors or in closed spaces.

(Fig. 17) The exhaust fumes from the engine contain

carbon monoxide, an odourless, poisonous

and very dangerous gas. Do not run the

product indoors or in closed spaces.

6 869 - 004 - 03.12.2018

Note: Other symbols/decals on the product refer to

certification requirements for other commercial areas.

EU V

WARNING: Tampering with the engine

voids the EU type-approval of this product.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

•

the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of injury or

death for the operator or bystanders if the

instructions in the manual are not obeyed.

CAUTION: Used if there is a risk of damage

to the product, other materials or the

adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary in

a given situation.

General safety instructions

WARNING: Read the warning instructions

that follow before you use the product.

• This product is dangerous if used incorrectly or if you

are not careful. Injury or death can occur if you do

not obey the safety instructions.

• This product produces an electromagnetic field

during operation. This field may under some

circumstances interfere with active or passive

medical implants. To reduce the risk of serious or

fatal injury we recommend persons with medical

implants to consult their physician and the medical

implant manufacturer before operating this product.

•

Always be careful and use your common sense. If

you are not sure how to operate the product in a

special situation, stop and speak to your McCulloch

dealer before you continue.

• Keep in mind that the operator will be held

responsible for accidents that involve other persons

or their property.

• Keep the product clean. Make sure that you can

clearly read signs and decals.

• Do not let a person use the product unless you make

sure that they read and understand the contents of

the operator's manual.

• Do not let a child operate the product.

•

Do not let a person, without knowledge of the

instructions, operate the product.

• Always monitor a person, with decreased physical

capacity or mental capacity, that uses the product. A

responsible adult must be there at all times.

• Do not use the product if you are tired, ill, or under

the influence of alcohol, drugs or medicine. This has

a negative effect on your vision, alertness,

coordination and judgment.

• Do not use the product if it is defective.

• Do not change this product or use it if it is possible

that it has been changed by others.

Work area safety

WARNING: Read the warning instructions

that follow before you use the product.

• Remove objects such as branches, twigs and stones

from the work area before you use the product.

• Objects that hit against the cutting equipment can

eject and cause damage to persons and objects.

Keep bystanders and animals at a safe distance

from the product.

•

Never use the product in bad weather such as fog,

rain, strong winds, intense cold and risk of lightning.

To use the product in bad weather or in moist or wet

locations is tiring. Bad weather can cause dangerous

conditions, such as slippery surfaces.

• Look out for persons, objects and situations that can

prevent safe operation of the product.

• Look out for obstacles, such as roots, stones, twigs,

pits and ditches. Long grass can hide obstacles.

• To cut grass on slopes can be dangerous. Do not

use the product on ground that slopes more than

15°.

869 - 004 - 03.12.2018 7

• Operate the product across the face of slopes. Do

not move up and down.

• Be careful when you go near hidden corners and

objects that prevent a clear view.

Work safety

WARNING: Read the warning instructions

that follow before you use the product.

• Use this product to cut grass lawns only. It is not

permitted to use it for other tasks.

• Use personal protective equipment. Refer to

Personal protective equipment on page 8

.

• Make sure that you know how to stop the engine

quickly in an emergency.

• Never start the engine in a closed space or near

flammable material. The exhaust fumes from the

engine are hot and can contain sparks which can

start a fire.

• Do not operate the product unless the blade and all

covers are attached correctly. An incorrectly

attached blade can come loose and cause personal

injury.

• Make sure that the blade does not hit objects such

as stones and roots. This can do damage to the

blade and bend the engine shaft. A bent axle causes

heavy vibration and a very high risk that the blade

becomes loose.

• If the blade hits an object or if vibrations occur, stop

the product immediately. Disconnect the ignition

cable from the spark plug. Examine the product for

damages. Repair damages or let an authorised

service agent do the repair.

• Never attach the engine brake handle permanently

to the handle when the engine is started.

• Put the product on a stable, flat surface and start it.

Make sure that the blade does not hit the ground or

other objects.

• Always stay behind the product when you operate it.

• Let all the wheels stay on the ground and keep 2

hands on the handle when you operate the product.

Keep your hands and feet away from the rotating

blades.

• Do not tilt the product when the engine is started.

• Be careful when you pull the product rearward.

• Never lift up the product when the engine is started.

If you must lift the product, first stop the engine and

disconnect the ignition cable from the spark plug.

• Do not walk rearward when you operate the product.

• Stop the engine when you move across areas

without grass, for example paths made of gravel,

stone and asphalt.

• Do not run with the product when the engine is

started. Always walk when you operate the product.

• Stop the engine before you change the cutting

height. Never make adjustments with the engine

started.

• Never let the product stay out of view with the engine

started. Stop the engine and make sure that the

cutting equipment does not rotate.

Safety instructions for operation

Personal protective equipment

WARNING: Read the warning instructions

that follow before you use the product.

• Personal protective equipment cannot fully prevent

injury but it decreases the degree of injury if an

accident does occur. Let your dealer help you select

the right equipment.

• Use hearing protection if the noise level is higher

than 85 dB.

•

Use heavy-duty slip-resistant boots or shoes. Do not

use open shoes or go with bare feet.

• Use heavy, long pants.

• Use protective gloves when necessary, for example

when you attach, examine or clean the cutting

equipment.

Safety devices on the product

WARNING: Read the warning instructions

that follow before you use the product.

• Do not use a product with defective safety devices.

• Do a check of the safety devices regularly. If the

safety devices are defective, speak to your

McCulloch

service agent.

To do a check of the cutting cover

The cutting cover decreases vibrations in the product

and decreases the risk of injury from the blade.

• Examine the cutting cover to make sure that there

are no damages such as cracks.

Engine brake handle

The engine brake handle stops the engine. When the

engine brake handle is released, the engine stops.

To do an inspection of the engine brake, start the engine

and then release the engine brake handle. If the engine

does not stop in 3 seconds, let an approved McCulloch

service agent adjust the engine brake.

(Fig. 18)

Muffler

The muffler keeps the noise levels to a minimum and

sends the exhaust fumes away from the operator.

Do not use the product if the muffler is missing or

defective. A defective muffler increases the noise level

and the risk of fire.

8 869 - 004 - 03.12.2018

WARNING: The muffler becomes very hot

during and after use and when the engine

operates at idle speed. Be careful near

flammable materials and/or fumes to prevent

fire.

To do a check of the muffler

• Examine the muffler regularly to make sure that it is

attached correctly and not damaged.

Fuel safety

WARNING: Read the warning instructions

that follow before you use the product.

• Do not start the product if there is fuel or engine oil

on the product. Remove the unwanted fuel/oil and let

the product dry.

• If you spill fuel on your clothing, change clothing

immediately.

•

Do not get fuel on your body, it can cause injury. If

you get fuel on your body, use soap and water to

remove the fuel.

• Do not start the product if the engine has a leak.

Examine the engine for leaks regularly.

• Be careful with fuel. Fuel is flammable and the fumes

are explosive and can cause injuries or death.

• Do not breathe in the fuel fumes, it can cause injury.

Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put warm objects near the fuel or the engine.

• Do not add the fuel when the engine is on.

• Make sure that the engine is cool before you refuel.

• Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

• Do not add fuel to the engine in an indoor area. Not

sufficient airflow can cause injury or death because

of asphyxiation or carbon monoxide.

• Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

• Move the product a minimum of 3 m / 10 ft from the

position where you filled the tank before a start.

•

Do not fill the fuel tank fully. Heat causes the fuel to

expand. Keep a space at the top of the fuel tank.

Safety instructions for maintenance

WARNING: Read the warning instructions

that follow before you use the product.

• The exhaust fumes from the engine contain carbon

monoxide, an odourless, poisonous and very

dangerous gas. Do not start the engine indoors or in

closed spaces.

• Before you do the maintenance on the product, stop

the engine and remove the ignition cable from the

spark plug.

•

Use protective gloves when you do maintenance on

the cutting equipment. The blade is very sharp and

cuts can easily occur.

• Accessories and changes to the product that are not

approved by the manufacturer, can cause serious

injury or death. Do not change the product. Always

use accessories that are approved by the

manufacturer.

• If the maintenance is not done correctly and

regularly, the risk of injury and damage to the

product increases.

• Only do the maintenance as given in this owner's

manual. All other servicing must be done by an

approved McCulloch service agent.

• Let an approved McCulloch service agent do

servicing on the product regularly.

• Replace damaged, worn or broken parts.

Assembly

To assemble the handle

Lower handle section

1.

Put the pins at the bottom of the lower handle into

the holes as given in the illustration. Align the screw

holes and attach the screws, washers and knobs.

(Fig. 19)

Upper handle section

1.

Align the holes in the handlebar with the holes in the

lower handle and attach the screws, washers and

knobs. On the right side also attach the loop for the

starter rope. Tighten the knobs fully. (Fig. 20)

2. Pull the starter rope handle and put the starter rope

around the loop for the starter rope. (Fig. 21)

3. Use the straps to attach the cables to the handle.

(Fig. 22)

Note: Make sure that the tension in the cables is not

too high.

To assemble the grass catcher

(M40-120 CLASSIC, M40-125

CLASSIC+, M46-120 CLASSIC,

M46-120R CLASSIC, M46-125

CLASSIC+, M46-125R CLASSIC+,

M46-150WR CLASSIC, M51-140WR

CLASSIC+, M51-150R CLASSIC,

869 - 004 - 03.12.2018 9

M51-150WR CLASSIC, M53-150WR

CLASSIC)

1. Put the grass catcher frame into the fabric grass

bag. Make sure that the handle on the grass catcher

frame is on top of the grass bag.

2.

Attach the grass bag to the grass catcher frame with

the clips found on the fabric bag edge. (Fig. 23)

3. Lift the rear cover.

4. Attach the grass catcher to the top edge of the

chassis.

5. Put the lower part of the grass catcher into the grass

discharge channel.

To assemble the grass catcher

(M46-140R CLASSIC+, M46-145WRP

CLASSIC+)

1. Put the upper part of the grass catcher onto the

lower part of the grass catcher.

2. Attach the grass catcher frame with the clips. (Fig.

24)

3. Lift the rear cover.

4.

Attach the hooks on the grass catcher to the top

edge of the chassis. (Fig. 25)

5. Put the lower part of the grass catcher into the grass

discharge channel.

To assemble the mulch plug

A mulch kit is available as an optional accessory for

selected models only. Models M46-140R CLASSIC+,

M46-145WRP CLASSIC+, M51-150WR CLASSIC,

M53-150WR CLASSIC come with the mulch kit

supplied. Models M40-120 CLASSIC, M40-125

CLASSIC+ can not be used with a mulch kit.

1. Lift up the rear cover and remove the grass catcher.

2. Put the mulch plug into the discharge channel. (Fig.

26)

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

Before you operate the product

1. Read the operator's manual carefully and make sure

that you understand the instructions.

2. Examine the cutting equipment to make sure that it

is correctly attached and adjusted. See

To examine

the cutting equipment on page 12

.

3. Fill the fuel tank. See

To fill fuel on page 10

.

4. Fill the oil tank and do a check of the oil level. See

To do a check of the oil level on page 12

.

To fill fuel

If available, use low-emission/alkylate gasoline. If low-

emission/alkylate gasoline is not available, use good

quality unleaded gasoline or leaded gasoline. Use

gasoline with an octane number of 90 RON out of North

America (87 AKI in North America) or higher, and with a

maximum of 10% ethanol (E10).

CAUTION: Do not use gasoline with an

octane number less than 90 RON out of

North America (87 AKI in North America).

This can cause damage to the product.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove it

with a cloth and let remaining fuel dry off.

3.

Clean the area around the fuel tank cap.

4. Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

5.

Move the product a minimum of 3 m (10 ft) from the

position where you filled the tank, before a start.

To set the cutting height

1. Move the cutting height lever rearward to increase

the cutting height.

2. Move the cutting height lever forward to decrease

the cutting height. (Fig. 27)

CAUTION: Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

To start the product

1. Make sure that the ignition cable is connected to the

spark plug.

2.

The very first time you start the product, press the

primer bulb 5 times. The next time you start the

product when the engine is cold, press the primer

bulb 3 times. (Fig. 28)

3. Stay behind the product.

4. Hold the engine brake handle against the handlebar.

(Fig. 29)

5. Hold the starter rope handle with your right hand.

6. Slowly pull out the starter rope until you feel some

resistance.

7. Pull with force to start the engine.

10 869 - 004 - 03.12.2018

WARNING: Do not twist the starter rope

around your hand.

To use the drive on the wheels

• Push the drive bail in the direction of the handlebar.

(Fig. 30)

• Before you pull the product rearward, disengage the

drive and push the product forward approximately

10cm.

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To stop the product

• To stop the drive only, release the drive bail.

• To stop the engine, release the engine brake handle.

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

•

Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

Maintenance

Introduction

WARNING: Before you do maintenance,

you must read and understand the safety

chapter.

For all servicing and repair work on the product, special

training is necessary. We guarantee the availability of

professional repairs and servicing. If your dealer is not a

service agent, speak to them for information about the

nearest service agent.

Maintenance schedule

The maintenance intervals are calculated from daily use

of the product. The intervals change if the product is not

used daily.

For maintenance identified with * see instructions in

Safety devices on the product on page 8

.

Maintenance Daily Weekly Monthly

Do a general inspection X

Examine the oil level X

Clean the product X

Examine the cutting equipment X

Examine the cutting cover* X

Examine the engine brake handle* X

Examine and adjust the drive (clutch wire) X

Examine the muffler* X

Examine the spark plug X

Change the oil (the first time after 5 h use, then after each 50 h use) X

Change the air filter X

Examine the fuel system X

To do a general inspection

• Make sure that the nuts and screws on the product

are tightened.

To clean the product externally

• Use a brush to remove leaves, grass and dirt.

869 - 004 - 03.12.2018 11

• Make sure that the air intake on the top of the engine

is not blocked.

• Do not use a high pressure washer to clean the

product.

•

If you use water to clean the product, do not flush

water directly on the engine.

To clean the inner surface of the

cutting cover

1. Empty the fuel tank.

2. Put the product on its side with the muffler down.

CAUTION: If the product is put with the

air filter down, the engine can become

damaged.

3. Hose down the inner surface of the cutting cover

with water.

To examine the cutting equipment

WARNING: To prevent accidental start

remove the ignition cable from the spark

plug.

WARNING: Use protective gloves when you

do maintenance on the cutting equipment.

The blade is very sharp and cuts can easily

occur.

1. Examine the cutting equipment for damage or

cracks. Always replace a damaged cutting

equipment.

2. Look at the blade to see if it is damaged or blunt.

Note:

It is necessary to balance the blade after it is

sharpened. Let a service center sharpen, replace and

balance the blade. If you hit an obstacle that causes the

product to stop, replace the damaged blade. Let the

service center estimate if the blade can be sharpened or

must be replaced.

To replace the blade

1. Lock the blade with a block of wood.

(Fig. 31)

2. Remove the blade bolt.

3. Remove the blade.

4. Examine the blade support and blade bolt to see if

there are damages.

5. Examine the engine shaft to make sure that it is not

bent.

6. When you attach the new blade, point the angled

ends of the blade in the direction of the cutting cover.

(Fig. 32)

7. Make sure that the blade is aligned with the center of

the engine shaft.

8. Lock the blade with a block of wood. Attach the

spring washer and tighten the bolt and washer with a

torque of 45–60 Nm. (Fig. 33)

9. Pull the blade around by hand and make sure that it

turns freely.

WARNING: Use heavy duty gloves. The

blade is very sharp and cuts can easily

occur.

10. Start the product to do a test of the blade. If the

blade is not correctly attached, there is vibration in

the product or the cutting result is unsatisfactory.

To do a check of the oil level

CAUTION: A too low oil level can do

damage to the engine. Do a check of the oil

level before you start the product.

1. Put the product on level ground.

2. Remove the oil tank cap with the attached dipstick.

3.

Clean the oil from the dipstick.

4. Put the dipstick fully into the oil tank to give a correct

picture of the oil level.

5. Remove the dipstick.

6. Examine the oil level on the dipstick.

7. If the oil level is low, fill with engine oil and do a

check of the oil level again.

To change the engine oil

WARNING: Engine oil is very hot directly

after the engine is stopped. Let the engine

become cool before you drain the engine oil.

If you spill engine oil on your skin, clean with

soap and water.

1. Operate the product until the fuel tank is empty.

2. Remove the ignition cable from the spark plug.

3.

Remove the oil tank cap.

4. Put a container below the product to collect the

engine oil in.

5. Tilt the product to drain the engine oil from the oil

tank.

6. Fill with new engine oil of the type recommended in

Technical data on page 14

.

7. Do a check of the oil level. See

To do a check of the

oil level on page 12

.

Air filter

An air filter that is used for a long time cannot be fully

cleaned. Replace the air filter at regular intervals.

Note: Always replace a damaged air filter.

12 869 - 004 - 03.12.2018

To clean the paper filter

1. Remove the air filter cover and remove the paper

filter.

2.

Hit the filter against a flat surface to make the

particles fall off.

CAUTION: Do not use solvent or

compressed air to clean the paper filter.

3. Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

4. Put the air filter cover back.

To clean the foam plastic filter

1.

Remove the air filter cover and remove the foam

plastic filter.

2. Clean the foam plastic filter with soap and water.

3. Flush the foam plastic filter in clean water.

4. Squeeze the water from the foam plastic filter and let

it dry.

CAUTION: Do not use compressed air.

It can cause damage to the foam plastic

filter.

5. Lubricate the foam plastic filter with engine oil.

6. Press a clean cloth against the foam plastic filter to

remove unwanted oil.

7.

Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

8. Put the air filter cover back.

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:

a) Make sure that the idle speed is correctly

adjusted.

b)

Make sure that the fuel mixture is correct.

c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, refer to

Technical data

on page 14

. (Fig. 34)

• Replace the spark plug if it is necessary.

To examine the fuel system

• Examine the fuel tank cap and the seal for the fuel

tank cap to make sure that there are no damages.

• Examine the fuel hose to make sure that there are

no leaks. If the fuel hose is damaged, let a service

agent replace it.

To adjust the clutch wire

If the drive feels slow, it is necessary to adjust the clutch

wire.

1. Attach the clutch wire in different holes on the drive

bail to adjust the length of the clutch wire. Decrease

the length of the clutch wire to increase the drive

speed. Extend the clutch wire to decrease the drive

speed. (Fig. 35)

Note: If the drive is engaged when you do not pull

the drive bail, it is necessary to extend the clutch

wire.

2. For small adjustment of the drive speed, turn the

adjuster screw. To increase the drive speed, turn the

adjuster screw counterclockwise. To decrease the

drive speed, turn the adjustment screw clockwise.

(Fig. 36)

If the drive feels slow also after the adjustment, let an

approved service agent replace the drive belt.

Transportation, storage and disposal

Transportation and storage

• For storage and transportation of the product and

fuel, make sure that there are no leaks or fumes.

Sparks or open flames, for example from electrical

devices or boilers, can start a fire.

•

Always use approved containers for storage and

transportation of fuel.

• Empty the fuel tank and the carburetor bowl before

you put the product in storage for a long period of

time. Discard the fuel at an applicable disposal

location

• Safely attach the product during transportation to

prevent damage and accidents.

• Keep the product in a locked area to prevent access

for children or persons that are not approved.

•

Keep the product in a dry and frost free area.

Disposal

• Obey the local recycling requirements and applicable

regulations.

• Discard all chemicals, such as engine oil or fuel, at a

service center or at an applicable disposal location.

869 - 004 - 03.12.2018 13

• When the product is no longer in use, send it to a

McCulloch dealer or discard it at a recycling location.

Technical data

M40-120

CLASSIC

M40-125

CLASSIC+

M46-120

CLASSIC

M46-120R

CLASSIC

M46-125

CLASSIC+

Engine

Brand McCulloch Briggs & Strat-

ton

McCulloch McCulloch Briggs & Strat-

ton

Displacement, cm

3

120 125 120 120 125

Speed, rpm 2900 2900 2900 2900 2900

Nominal engine output, kW

1

2.0 1.6 2.0 2.0 1.6

Ignition system

Spark plug K7RTC RC12YC K7RTC K7RTC RC12YC

Electrode gap, mm 0.7 0.5 0.7 0.7 0.5

Fuel and lubrication system

Fuel tank capacity, litre 0.8 0.8 0.8 0.8 0.8

Oil tank capacity, litre 0.4 0.4 0.4 0.4 0.4

Engine oil

2

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

Weight

With empty tanks, kg 24 25 28 29 28

Noise emissions

3

Sound power level, measured

dB (A)

93 93 95 95 95

Sound power level, guaranteed

L

WA

dB (A)

94 94 96 96 96

Sound levels

4

Sound pressure level at the op-

erator's ear, dB (A)

80 80 82 82 82

Vibration levels, a

hveq

5

1

The power rating of the engine indicated is the average net output (at specified rpm) of a typical production

engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ

from this value. Actual power output for the engine installed on the final product will depend on the operating

speed, environmental conditions and other values.

2

Use engine oil of quality SJ or higher. See the viscosity chart in the engine manufacturer’s manual and select

the best viscosity based on the expected outside temperature.

3

Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive

2000/14/EC.

4

Noise pressure level according to ISO 5395:2013. Reported data for noise pressure level has a typical statisti-

cal dispersion (standard deviation) of 1.2 dB (A).

5

Vibration level according to ISO 5395:2013. Reported data for vibration level has a typical statistical disper-

sion (standard deviation) of 0.2 m/s

2

.

14 869 - 004 - 03.12.2018

M40-120

CLASSIC

M40-125

CLASSIC+

M46-120

CLASSIC

M46-120R

CLASSIC

M46-125

CLASSIC+

Handle, m/s

2

14.75 14.75 15.68 15.68 15.68

Cutting equipment

Cutting height, mm 20–75 20–75 30–80 30–80 30–80

Cutting width, mm 400 400 460 460 460

Blade Mulcher 40 Mulcher 40 Mulcher 46 Mulcher 46 Mulcher 46

Article number 5871590-10 5871590-10 5811889-10 5811889-10 5811889-10

Grass catcher capacity, liter 50 50 50 50 50

M46-125R

CLASSIC+

M46-140R

CLASSIC+

M46-145WRP

CLASSIC+

M46-150WR

CLASSIC

M51-140WR

CLASSIC+

Engine

Brand Briggs & Strat-

ton

Briggs & Strat-

ton

Honda McCulloch Briggs & Strat-

ton

Displacement, cm

3

125 140 145 150 140

Speed, rpm 2900 2900 2900 2900 2900

Nominal engine output, kW

6

1.6 1.98 2.9 2.4 1.9

Ignition system

Spark plug RC12YC RC12YC BPR5ES K7RTC RC12YC

Electrode gap, mm 0.5 0.5 0.5 0.7 0.5

Fuel and lubrication system

Fuel tank capacity, liter 0.76 0.8 0.95 1.0 0.76

Oil tank capacity, liter 0.4 0.5 0.4 0.4 0.4

Engine oil

7

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

Weight

With empty tanks, kg 27 30 33.5 32 32

Noise emissions

8

Sound power level, measured

dB (A)

95 95 95 97 97

6

The power rating of the engine indicated is the average net output (at specified rpm) of a typical production

engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ

from this value. Actual power output for the engine installed on the final product will depend on the operating

speed, environmental conditions and other values.

7

Use engine oil of quality SJ or higher. See the viscosity chart in the engine manufacturer’s manual and select

the best viscosity based on the expected outside temperature.

8

Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive

2000/14/EC.

869 - 004 - 03.12.2018 15

M46-125R

CLASSIC+

M46-140R

CLASSIC+

M46-145WRP

CLASSIC+

M46-150WR

CLASSIC

M51-140WR

CLASSIC+

Sound power level, guaranteed

L

WA

dB (A)

96 96 95 98 98

Sound levels

9

Sound pressure level at the op-

erator's ear, dB (A)

82 81 80 82 82

Vibration levels, a

hveq

10

Handle, m/s

2

15.68 15.68 3.06 4.27 4.27

Cutting equipment

Cutting height, mm 30–80 30–80 30–80 30–80 30–90

Cutting width, mm 460 460 460 460 510

Blade Mulcher 46 Mulcher 46 Mulcher 46 Mulcher 46 Mulcher 51

Article number 5811889-10 5811889-10 5811889-10 5811889-10 5041133-10

Grass catcher capacity, liter 50 50 50 55 55

M51-150R CLASSIC M51-150WR CLAS-

SIC

M53-150WR CLAS-

SIC

Engine

Brand McCulloch McCulloch McCulloch

Displacement, cm

3

150 150 150

Speed, rpm 2900 2900 2900

Nominal engine output, kW

11

2.4 2.4 2.4

Ignition system

Spark plug K7RTC K7RTC K7RTC

Electrode gap, mm 0.7 0.7 0.7

Fuel and lubrication system

Fuel tank capacity, liter 1.0 1.0 1.0

Oil tank capacity, liter 0.4 0.4 0.4

Engine oil

12

SAE 30/SAE 10W-30 SAE 30/SAE 10W-30 SAE 30/SAE 10W-30

9

Noise pressure level according to ISO 5395:2013. Reported data for noise pressure level has a typical statisti-

cal dispersion (standard deviation) of 1.2 dB (A).

10

Vibration level according to ISO 5395:2013. Reported data for vibration level has a typical statistical disper-

sion (standard deviation) of 0.2 m/s

2

.

11

The power rating of the engine indicated is the average net output (at specified rpm) of a typical production

engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ

from this value. Actual power output for the engine installed on the final product will depend on the operating

speed, environmental conditions and other values.

12

Use engine oil of quality SJ or higher. See the viscosity chart in the engine manufacturer’s manual and select

the best viscosity based on the expected outside temperature.

16 869 - 004 - 03.12.2018

M51-150R CLASSIC M51-150WR CLAS-

SIC

M53-150WR CLAS-

SIC

Weight

With empty tanks, kg 33 33 33

Noise emissions

13

Sound power level, measured dB (A) 95 97 98

Sound power level, guaranteed L

WA

dB (A) 98 98 98

Sound levels

14

Sound pressure level at the operator's ear,

dB (A)

81 84 82

Vibration levels, a

hveq

15

Handle, m/s

2

4.06 5.55 3.39

Cutting equipment

Cutting height, mm 30–90 30–90 30–90

Cutting width, mm 510 510 530

Blade Mulcher 51 Mulcher 51 Mulcher 53

Article number 5041133-10 5041133-10 5811886-10

Grass catcher capacity, liter 55 55 55

EC Declaration of Conformity

Contents of the EC Declaration of Conformity

We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, declare under our sole responsibility that the represented

product:

Description Combustion-engine-powered pedestrian-controlled lawn mower

Brand McCulloch

Platform / Type / Model M40-120 CLASSIC, M40-125 CLASSIC+, M46-120 CLASSIC, M46-120R CLAS-

SIC, M46-125 CLASSIC+, M46-125R CLASSIC+, M46-140R CLASSIC+,

M46-145WRP CLASSIC+, M46-150WR CLASSIC, M51-140WR CLASSIC+,

M51-150R CLASSIC, M51-150WR CLASSIC, M53-150WR CLASSIC

Batch Serial number dating 2017 and onwards

complies fully with the following EU directives and regulations:

13

Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive

2000/14/EC.

14

Noise pressure level according to ISO 5395:2013. Reported data for noise pressure level has a typical statisti-

cal dispersion (standard deviation) of 1.2 dB (A).

15

Vibration level according to ISO 5395:2013. Reported data for vibration level has a typical statistical disper-

sion (standard deviation) of 0.2 m/s

2

.

869 - 004 - 03.12.2018 17

Directive/Regulation

Description

2006/42/EC “relating to machinery”

2014/30/EU “relating to electromagnetic compatibility”

2000/14/EC; 2005/88/EC “relating to outdoor noise”

Harmonized standards and/or technical specifications applied are as follows: EN ISO 12100, ISO 14982, ISO

5395-1 & 2, ISO 3744, ISO 11094, EN 1032

In accordance with directive 2000/14/EC, Annex V, the declared sound values are stated in the technical data sec-

tion of this manual and in the signed EC Declaration of Conformity.

The supplied combustion-engine-powered pedestrian-controlled lawn mower conforms to the example that under-

went examination.

18 869 - 004 - 03.12.2018

Содержание

Въведение..................................................................19

Безопасност...............................................................

20

Монтаж........................................................................ 23

Операция.................................................................... 24

Поддръжка................................................................. 25

Транспортиране, съхранение и изхвърляне....... 28

Технически характеристики....................................28

Декларация за съответствие на ЕО.......................32

Въведение

Описание на продукта

Продуктът е пешеходна ротационна косачка.

Тревата се събира в кош за трева. Свалете коша за

трева, за да се получи задно разтоварване на

тревата. Поставете комплект за мулчиране

(допълнителна принадлежност), за да нарежете

тревата в тора.

Предназначение

Използвайте продукта, за да косите трева в частни

градини. Не използвайте продукта за други задачи.

Общ преглед на продукта

(Фиг. 1)

1. Дръжка за задвижване (M46-120R CLASSIC,

M46-125R CLASSIC+, M46-150WR CLASSIC,

M51-140WR CLASSIC+, M51-150R CLASSIC,

M51-150WR CLASSIC, M53-150WR CLASSIC,

M46-140R CLASSIC+, M46-145WRP CLASSIC+)

2.

Горна дръжка/управление

3. Ръчка за спирачката на двигателя

4. Дръжка на въжето на стартера

5. Ухо за стартерното въже

6. Кош за трева

7. Ниска ръкохватка

8. Долна част на дръжката

9. Лостове за височината на рязане

10. Капачка за маслото

11. Ауспух

12. Канал за източване за камерата на карбуратора

13. Подкачваща помпа

14. Запалителна свещ

15. Резервоар за гориво

16. Нож

17. Пружинна шайба

18. Болт на режещ диск

19. Косилен апарат

20. Въздушен филтър

21. Инструкция за експлоатация

Символи върху машината

(Фиг. 2) ПРЕДУПРЕЖДЕНИЕ: Непредпазливото

или неправилното използване може да

доведе до нараняване или смърт на

оператора или страничните наблюдатели.

(Фиг. 3) Прочетете внимателно ръководството за

оператора и се уверете, че разбирате

инструкциите, преди да използвате

машината.

(Фиг. 4) Дръжте хората и животните на безопасно

разстояние от работната зона.

(Фиг. 5) Спрете двигателя и отстранете

запалителния кабел преди ремонти или

техническо обслужване.

(Фиг. 6) Пазете се от отскачащи предмети и

рикошети.

(Фиг. 7) Предупреждение: въртящ се нож.

Осигурете пространство около ръцете и

краката си.

(Фиг. 8) Предупреждение: въртящи се части.

Осигурете пространство около ръцете и

краката си.

(Фиг. 9) Този продукт е в съответствие с

приложимите директиви на ЕО

(Фиг. 10) Шумови емисии в околната среда в

съответствие с Директивата на

Европейската общност Емисиите на

продукта са посочени в раздела за

технически характеристики и на

табелката.

(Фиг. 11) Риск от пожар.

(Фиг. 12) Риск от пожар.

(Фиг. 13) Риск от експлозия.

(Фиг. 14) Винаги изключвайте двигателя преди

зареждане с гориво.

869 - 004 - 03.12.2018 19

(Фиг. 15) Гореща повърхност.

(Фиг. 16) Отработените газове от двигателя

съдържат въглероден окис – много

опасен, отровен газ без миризма. Не

работете с машината на закрито или в

затворени пространства.

(Фиг. 17) Отработените газове от двигателя

съдържат въглероден окис – много

опасен, отровен газ без миризма. Не

работете с машината на закрито или в

затворени пространства.

Забележка: Останалите символи/стикери на

продукта се отнасят до изисквания по отношение на

сертификати за други търговски зони.

EU V

ПРЕДУПРЕЖДЕНИЕ: Намесата в

двигателя прави невалидно ЕС

одобрението на тип на този продукт.

Отговорност за вреди, причинени

от стоки

Както е посочено в законите за отговорност за

вреди, причинени от стоки, ние не носим отговорност

за щети, причинени от нашия продукт, ако:

• продуктът е неправилно ремонтиран.

•

продуктът е ремонтиран с части, които не са от

производителя или не са одобрени от

производителя.

• продуктът има принадлежност, която не е от

производителя или не е одобрена от

производителя.

• продуктът не е ремонтиран в одобрен сервизен

център или от одобрен орган.

Безопасност

Дефиниции за безопасност

Предупреждения, знаци за внимание и бележки се

използват за указване на особено важни части на

инструкцията.

ПРЕДУПРЕЖДЕНИЕ: Използва се, ако

има опасност от нараняване или смърт за

оператора или за околните, ако не се

спазват инструкциите в ръководството.

ВНИМАНИЕ: Използва се, ако има

опасност от повреждане на машината,

други материали или съседната зона, ако

не се спазват инструкциите в

ръководството.

Забележка: Използва се за предоставяне на повече

информация, която е необходима в дадена ситуация.

Общи инструкции за безопасност

ПРЕДУПРЕЖДЕНИЕ: Прочетете

следващите предупредителни указания,

преди да използвате машината.

• Този продукт е опасен, ако се използва

неправилно или ако не сте внимателни.

Неспазването на инструкциите за безопасност

може да доведе до нараняване или смърт.

• Тази машина създава електромагнитно поле по

време на работа. При някои условия това поле

може да интерферира с активни или пасивни

медицински имплантанти. За да намалите риска

от тежко или смъртоносно нараняване, ние

препоръчваме лицата с медицински импланти да

говорят с лекаря си и производителя на

медицинския имплант, преди да започнат да

работят с тази машина.

• Винаги бъдете внимателни и подхождайте

разумно. Ако не сте сигурни как да работите с

продукта при специална ситуация, спрете и се

обърнете към Вашия дилър на McCulloch

,преди

да продължите.

• Имайте предвид, че операторът носи отговорност

за нещастни случаи, включващи други хора или

тяхното имущество.

• Поддържайте продукта чист. Уверете се, че

разчитате ясно знаците и стикерите.

• Не позволявайте на когото и да е да работи с

продукта, докато не се уверите, че е прочел и

разбрал съдържанието на инструкцията за

експлоатация.

• Не позволявайте на деца да работят с продукта.

• Не позволявайте на лица, които не са запознати с

инструкциите, да работят с продукта.

• Винаги наблюдавайте лица с намален физически

или умствен капацитет, които използват

продукта. През цялото време трябва да

присъства отговорен възрастен.

• Не използвайте продукта, ако сте уморени, болни

или под въздействието на алкохол, наркотици

или лекарства. Това състояние оказва

отрицателно въздействие върху Вашето зрение,

бдителност, координация и преценка.

• Не използвайте продукта, ако е неизправен.

20 869 - 004 - 03.12.2018

Pagina se încarcă ...

McCulloch M51-140WR Manualul proprietarului

McCulloch M51-140WR Manualul proprietarului

în alte limbi

Alte documente