LG 21HK512D-B Ghid de inițiere rapidă

Tip
Ghid de inițiere rapidă
Please read this manual carefully before operating your set and retain it for future reference.
21HK512D
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved.
OWNER’S MANUAL
MEDICAL MONITOR
*MFL71428806*
(2001-REV00)
2
ENGLISH
ON CLEANING
Recommended Cleaning Chemicals
Isopropanol 70 %
Ethanol 70 %
Cidex
®
OPA
0.9 % NaCl solution
How to Use Cleaner (When the screen has dust)
Prior to cleaning, turn off the monitor and remove the power cable.
Soak a soft cloth in a recommended cleaner, then lightly rub the screen with no more than 1 N of force.
The cleaner could cause serious damage if it leaks inside the monitor while cleaning.
The display could be damaged, so only clean the parts of the monitor other than the screen's LCD panel.
Do not use benzene, thinner, acids or alkaline cleaners or other such solvents.
Cleaning guidelines for displays must only be carried out by medical professionals (doctors or nurses) and
must not be handled by patients.
CONTENTS
ON CLEANING --------------------------------------------2
ASSEMBLY AND PREPARING --------------------------3
INITIAL INSTALLATION --------------------------------6
USER SETTINGS ----------------------------------------11
TROUBLESHOOTING ---------------------------------- 16
PRODUCT SPECIFICATION ---------------------------17
3
ENGLISH
ASSEMBLY AND PREPARING
Product Composition
Please check whether all the components are included in the box before using the product. If there are any
missing components, contact the retailer where you purchased the product.
Note that the product and related components may look different from those shown here.
DVI-D Cable DisplayPort Cable
Power Cord
CD/Owner's Manual/Regulatory
Manual/Cards
Cable holder
CAUTION
Always use genuine LG components to ensure safety and product performance.
The product warranty will not cover damage or injury caused by the use of unauthorized components.
It is recommend that use the supplied components.
If you use generic cables not certified by LG, the screen may not display or there may be image noises.
Always use authorized components from the table of accessories shown below. Unauthorized components
can cause damage and malfunction to the product.
Component Standard
DisplayPort Cable UL, Impedance 100 ohm
DVI-D Cable UL, Impedance 100 ohm
Power Cord US – Approved US safety regulation
Others – Approved country safety regulation
NOTE
The components may look different from those illustrated here.
Without prior notice, all product information and specifications contained in this manual are subject to
change to improve the performance of the product.
To purchase optional accessories, visit an electronics store or an online shopping site, or contact the retailer
from which you purchased the product.
The power cord provided may differ depending upon the region.
Supported Software
Check the software supported by your product and refer to the manuals on the CD enclosed in the product
package.
Software Installation Priority
Recommended
Required and Recommended: You can download and install the latest version from the enclosed CD or from
the LGE website (www.lg.com).
4
ENGLISH
Product and Button Description
Front View
Power LED
Indicator
Calibration Sensor
Auto
Luminance
Stability Sensor
APRX. Sensor
Power LED Indicator
LED Status Operation Description
Green Normal operation
Orange No signal/Power saving
Light Orange Power saving when people leave
LED off Power off
NOTE
Under normal operation, Power LED Indicator will be off after 20 seconds in order not to affect the image
reading quality in dark room.
To bring back the Power LED Indicator, press the OSD Control Knob or switch display condition.
5
ENGLISH
Rear View
2
3
4
5
6
8
7
USB IN 1 USB IN 2 USB UP USB (MSD) LAN DP IN DVI-D IN
AC INPUT ON / OFF
1
1
/ /
- One upstream two downstream ports.
- Peripheral USB device connection.
2
- USB A.
- Save test or calibration report to an external storage device, it is compatible with FAT32 only.
(For technician use only)
3
- RJ45.
- For sending calibration report to a target PC and synchronize with time server. (For technician
use only)
4
- Display Port 20 pin.
- Digital Connection.
5
- Dual-Link DVI-D.
- Digital Connection.
6
- AC power input.
- For operation with AC power.
7
Equipotential terminal
- Connect to other equipment’s potential equalization conductor.
8
(AC switch)
- For operation with AC power.
6
ENGLISH
Stand View
Unit: mm
100
100
429.3
18
247.9
INITIAL INSTALLATION
To attach the LCD monitor to your system, follow these instructions
1 Turn off the power of your computer.
2 For connecting the PC: Connect the DVI-D cables or DisplayPort cables to the connector of the display card
in your system. Tighten all screws.
3 Connect the DVI-D cables or DisplayPort cables to the connector on the back of the monitor.
4 Connect one end of the power cord to the monitor and the other end to the power outlet.
5 The AC switch on the back of the monitor must be turned on. Then turn on the monitor with the OSD
Control Knob.
6 For further adjustments, refer to the OSD section of this manual.
NOTE
Incorrect cable connections may result in irregular operation, damage display quality / components of LCD
module and/or shorten the module’s life.
Please refer to Caution of "ASSEMBLY AND PREPARING" section for proper selection of your Power cord.
The AC switch is a real on/off switch. If this switch is on the Off position, the monitor cannot be turned on by
using the OSD Control Knob.
If you have any questions, please refer to the "TROUBLESHOOTING" section of this manual.
7
ENGLISH
Moving and Lifting the Monitor
When moving or lifting the monitor, follow these instructions to prevent the monitor from being scratched or
damaged and to ensure safe transportation, regardless of its shape or size.
Place the monitor in the original box or packing material before attempting to move it.
Before moving or lifting the monitor, disconnect the power cord and all other cables.
Hold the bottom and side of the monitor frame firmly. Do not hold the panel itself.
When holding the monitor, the screen should face away from you to prevent it from being scratched.
When transporting the monitor, do not expose the monitor to shock or excessive vibration.
When moving the monitor, keep it upright and never turn the monitor on its side or tilt it sideways.
CAUTION
Avoid touching the monitor screen as much as possible.
- This may result in damage to the screen or some of the pixels used to create images.
If you use the monitor panel without the stand base, its OSD Control Knob may cause the monitor to become
unstable and fall, resulting in damage to the monitor or human injury. In addition, this may cause the OSD
Control Knob to malfunction.
Installing on a Table
Lift the monitor and place it on the table in an upright position. Place the monitor at least 100mm away
from the wall to ensure sufficient ventilation.
100 mm
100 mm
100 mm
100 mm
CAUTION
Unplug the power cord before moving or installing the monitor. There is risk of electric shock.
Make sure to use the power cord that is provided in the product package and connect it to a grounded power
outlet.
If you need another power cord, please contact your local dealer or the nearest retail store.
8
ENGLISH
Adjusting the Stand Height
1 Place the monitor mounted on the stand base in an upright position.
2 Handle the monitor with both hands for safety.
Max. 150.0 mm
WARNING
When adjusting the screen height, do not place your hand on the stand body to avoid injury to your fingers.
Adjusting the Angle
1 Place the monitor mounted on the stand base in an upright position.
2 Adjust the angle of the screen.
The angle of the screen can be adjusted forward or backward from -5° to 25° for a comfortable viewing
experience.
WARNING
To avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor’s frame as
illustrated below.
Be careful not to touch or press the screen area when adjusting the angle of the monitor.
Swivel stand
Swivel 45 degrees and adjust the angle of the Monitor set to suit your view.
Pivot Feature
The pivot feature allows the monitor to rotate 90 degrees clockwise or counter-clockwise.
Head
Stand
WARNING
To avoid scratching the stand base, do not use excessive force or speed when rotating the monitor using the
pivot feature, and make sure that the stand does not make contact with the monitor.
9
ENGLISH
1 Raise the monitor up to the maximum height.
2 Adjust the angle of the monitor in the direction of the arrow as shown in the figure.
3 Rotate the monitor clockwise or counter-clockwise as shown in the figure.
4 Complete the installation by rotating the monitor 90° as shown in the figure.
10
ENGLISH
NOTE
Auto Pivot feature of the display is not supported.
The screen can be rotated easily using the screen pivot shortcut key provided with your Windows operating
system. Note that some Windows versions and some graphics card drivers may use different settings for the
screen pivot key or may not support the pivot key at all.
Windows operating system screen pivot shortcut key.
- 0°: Ctrl + Alt + keyboard up key ( )
- 90°: Ctrl + Alt + keyboard left key ( )
- 180°: Ctrl + Alt + keyboard down key ( )
- 270°: Ctrl + Alt + keyboard right key ( )
WARNING
Take care when rotating the monitor if the cable is connected.
To avoid injury to your fingers, do not put them between the screen and the stand base when turning the
monitor's screen.
11
ENGLISH
USER SETTINGS
Menu Settings
OSD Control Knob
Your LCD monitor allows you to easily adjust the characteristics of the image being displayed. All of these
adjustments are made using the OSD Control Knob on the monitor. While you use this OSD Control Knob, an OSD
shows you their changes.
The applicable setting options are as shown below.
[Input] [Picture] [Gamma] [Info]
[OSD] [General] [Exit]
NOTE
Your monitor’s OSD (On Screen Display) may differ slightly from that shown in this manual.
OSD Control Knob
The OSD Control Knob is a multi-functional device located behind the Power LED Indicator on the right side of
the front bezel. It has three movements-rotate upward, rotate downward and press inward as a button.
Power On/Off Press the OSD Control Knob to power the unit on from the off stage
(the LED is off). To turn the power off, press the OSD Control Knob
and hold for at least 3 second until the LED turns off.
OSD Control While the monitor is on (green LED and image on the screen),
Pressing on the Control Knob activates the OSD. While the OSD menu
is active, use the three way movements of the Control Knob.
Rotate Downward Move Up/Right, Increase, Larger, More
Rotate Upward Move Down/Left, Decrease, Smaller, Less
OSD Control Knob
Press
Execute, Do, Save
12
ENGLISH
[Input]
[Input] Description
[DVI] Set current input to DVI.
[DISPLAYPORT] Set current input to Displayport.
[Picture]
[Picture] Description
[ALS]
(Auto Luminance Stability)
[Range] User define the ALS value.
[300] Adjust brightness to 300 cd/m2 (±10 %).
[400] Adjust brightness to 400 cd/m2 (±10 %).
[500] Adjust brightness to 500 cd/m2 (±10 %).
[600] Adjust brightness to 600 cd/m2 (±10 %).
[Off] Stop [ALS] and enable [Brightness].
[Auto] Auto select [ALS] according ambient light detected by Ambient sensor.
[Brightness]
Adjust the backlight of the full screen by the range from 0 to 100.
[Contrast]
Adjust the contrast for the display image by the range from 0 to 100.
[Color Temp] [6500K] Set Color temp to 6500K.
[7500K] Set Color temp to 7500K.
[9300K] Set Color temp to 9300K.
[Mono] Set Color temp to monochrome.
13
ENGLISH
[Gamma]
[Gamma] Description
[Gamma 1.8]
Set Gamma curve to curve 1.8.
[Gamma 2.0]
Set Gamma curve to curve 2.0.
[Gamma 2.2]
Set Gamma curve to curve 2.2.
[Gamma DICOM]
Set Gamma curve for medical standard. (DIN6868-157)
[Gamma User]
Set Gamma curve for user mode.
[Light Box]
Full screen in white.
[Info]
[Info] Description
System Information
Show Model name/Firmware Version/GPU Version/Monitor SN/H-Freq./V-Freq./Life Time/IP/ALS(LUX).
NOTE
Information of LUX is only for reference. For quality assurance test, please use standard equipment.
14
ENGLISH
[OSD]
[OSD] Description
[Rotation]
[Landscape] Set OSD Menu in landscape.
[Portrait] Set OSD Menu in portrait.
[Auto] Set OSD form by G-sensor.
[Language]
Sets the menu screen to the desired language.
[OSD Position]
Set horizontal and vertical position of OSD Menu.
[OSD Timer]
[10 sec.] Set OSD display time around 10 seconds.
[20 sec.] Set OSD display time around 20 seconds.
[30 sec.] Set OSD display time around 30 seconds.
[45 sec.] Set OSD display time around 45 seconds.
[60 sec.] Set OSD display time around 60 seconds.
[120 sec.] Set OSD display time around 120 seconds.
[OSD Lock]
[Yes] Select [Yes] to enable lock.
[No] Long press OSD Control Knob in lock.
[OSD Transparency]
Set transparency of OSD Menu.
15
ENGLISH
[General]
[General] Description
[All Reset]
[Yes] Reset all display and OSD setting to default value.
[No] Exit this page.
[APRX. Sensor]
[Off] Disable [APRX. Sensor] function.
[On] Set [APRX. Sensor] close the panel power when user isn’t in front of monitor.
[Auto] Save the P-distance and enable [APRX. Sensor] on. The arrow mark will point to [On].
[Zoom Up]
[Original] Keep image in normal resolution.
[Full] Scale up the resolution to 2048 x 1536.
[2X Scale] Scale up the specific part of image.
[Self Calibration]
[Yes] Enable monitor test luminance and calibrate DICOM with color temperature according to OSD setting.
[No] Exit this page.
[Cal. Date:]
NOTE
Show [Cal. Date:] in which [Self Calibration] is done. The [Cal. Date:] will be based on the date that is shown in the OSD menu, it can be synced to the real time/date via internet (RJ45). Please
connect the monitor with internet before AC On if user want to get real time/date when doing [Self Calibration].
16
ENGLISH
TROUBLESHOOTING
Problem Check to see
Nothing is displayed on the screen The signal cable should be completely connected to the display card/computer.
The display card should be completely seated in its slot.
Check the AC switch. Should be in the On position.
OSD Control Knob and computer power switch should be in the On position.
Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual
to change graphics mode)
Check the monitor and your display card with respect to compatibility and recommended settings.
Check the signal cable connector for bent or pushed-in pins.
Image persistence (Image Sticking) Image persistence is when a residual or ghost image of a previous image remains visible on the screen. To alleviate image persistence, turn off the
monitor for as long as the previous image was displayed.
Try not to operate the LCD with a fixed image on the screen for more than thirty minutes.
The screen has defective pixels The screen has defective pixels (e.g. slightly light or dark). This is due to the characteristics of the panel itself and not the LCD product.
Image is unstable, unfocused or swimming is apparent Signal cable should be completely attached to the computer.
Check the monitor and your display card with respect to compatibility and recommended signal timings.
If your text is garbled, change the video mode to non-interlace and use 50Hz refresh rate.
OSD is not sized properly Use the OSD Image Adjust controls to increase or decrease the coarse total.
Check to make sure that a supported mode has been selected on the display card or system being used.
Is the [No Signal] message displayed? Signal cable should be completely attached to the computer.
Make certain the computer is not in a power-saving mode. (Touch the keyboard or mouse)
If no video is present on the screen, turn the Power button off and on again.
LED on monitor is not lit (No Green or Light Orange can be seen) Power Switch should be in the On position and power cord should be connected.
Check the power cable should be connected surely. Press the OSD Control Knob or switch display condition with source or resolution.
17
ENGLISH
PRODUCT SPECIFICATION
The product specifications are subject to change without prior notice for product improvements.
“ ~ ” refers to alternating current (AC), refers to direct current (DC).
LCD Screen Type TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Screen
Pixel Pitch 0.2115 mm x 0.2115 mm
Resolution Max Resolution
2048 x 1536 @ 60 Hz
Recommended Resolution
Video Signal Horizontal Frequency 63 kHz - 96 kHz
Vertical Frequency 50 Hz - 75 Hz
Input Connector Equipotential terminal
Power Source Power Rating 100 - 240 V~ 50/60 Hz, 1.2 - 0.5 A
Power consumption Max. 85 W *
Environmental Conditions Operating Conditions Temperature 0 °C to 40 °C
Humidity 0 % to 80 %
Pressure 540 hPa to 1060 hPa
Storing Conditions Temperature -20 °C to 60 °C
Humidity 0 % to 80 %
Pressure 500 hPa to 1060 hPa
18
ENGLISH
Dimensions (mm) Monitor Size (Width x Height x Depth)
With Stand 377 x 606 x 248.2
Without Stand 377 x 473 x 89.6
Weight (kg) With Stand 9.8
Without Stand 7.0
Medical Specifications Classification by protection type against
Electric Shock
Class equipment
Mode of operation
Continuous Operation
Environment of Use
This equipment is not suitable for use in the presence of flammable anesthetic or oxygen.
* The Operating Mode of Power Consumption is measured with LGE test standard. (Full White pattern, Maximum resolution)
* The Power Consumption level can be different by operating condition and monitor setting.
19
ENGLISH
Display Mode
Pixel Format
Pixel Frequency Frequency Standard Input 1 Input 2
CLK (MHz) H (kHz) V (Hz) Type DVI-D DP
1280 x 1024 108 63.96 60.0 VESA V V
1600 x 1200 162 75.00 60.0 VESA V V
1920 x 1080 148.5 67.50 60.0 VESA V V
1920 x 1200 193.6 74.60 60.0 VESA V V
2048 x 1536 260 96.71 60.0 - V V
NOTE
Modes not listed in the table may not be supported. For optimal resolution, we recommend you to choose a mode listed in the above table.
Supported Graphic Card List
Vendor Graphic Card
The model and serial number of the product are located on the back and on one side of the product. Record
them below in case you ever need service.
Model
Serial No.
WARNING: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment
may cause radio interference.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260

LG 21HK512D-B Ghid de inițiere rapidă

Tip
Ghid de inițiere rapidă