Brooks GF / GI Instrucțiuni de utilizare

SolidSense II

®

Series

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

Brooks

®

SolidSense II

®

Series

Pressure Transducer

SolidSense II ATEX

Pressure Transmitter

Pigtail Conguration

SolidSense II

Pressure Transducer

15-Pin Flow Thru

Conguration

SolidSense II

Pressure Transducer

with Bendix

®

Conguration

SolidSense II

Pressure Transducer

with Integrated Digital

Display

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

ESD (Electrostatic Discharge)

CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed

during the removal, installation or other handling of internal circuit boards or devices.

Handling Procedure:

1. Power to unit must be removed.

2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,

removed or adjusted.

3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before

installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.

Comments

This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components

that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these

devices. Damaged components, even though they appear to function properly, exhibit early failure.

Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly

installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to

and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.

•To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.

•Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover

for local sales office contact information. Save this instruction manual for future reference.

WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed

this warning can result in serious personal injury and / or damage to the equipment.

• If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.

• Follow all warnings, cautions and instructions marked on and supplied with the product.

WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can

result in serious personal injury and / or damage to the equipment.

• Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.

Connect all products to the proper electrical and pressure sources.

• Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet

and outlet connections. If no leaks are present, bring the system up to the operating pressure.

• Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use

replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe

operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.

• Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when

maintenance is being performed by qualified persons.

WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely

drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.

All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).

• The Specifications Section of this manual contains instructions related to the PED directive.

• Products described in this manual are in compliance with EN directive 2014/34/EU.

• All Brooks Instrument Flowmeters fall under fluid group 1.

• Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.

• Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).

The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic

Compatibility (EMC directive 2014/30/EU).

Special attention however is required when selecting the signal cable to be used with CE marked equipment.

Quality of the signal cable, cable glands and connectors:

Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.

If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.

“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.

The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.

The shield should be terminated to an earth ground.

Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.

The shield should be terminated to an earth ground.

For pin configuration : Please refer to the enclosed Instruction Manual.

European Pressure Equipment Directive (PED)

European Electromagnetic Compatibility (EMC)

Essential Instructions

Read before proceeding!

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Dear Customer,

We appreciate this opportunity to service your pressure measurement and control requirements with a Brooks

Instrument device. Every day, customers all over the world turn to Brooks Instrument for solutions to their gas

and liquid control applications. Brooks provides an array of ow, pressure and level measurement and control

products for various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical

devices, analytical instrumentation, semiconductor manufacturing, and more.

The Brooks product you have just received is of the highest quality available, offering superior performance,

reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements

and hostile process environments in mind to provide you with a lifetime of dependable service.

We recommend that you read this manual in its entirety. Should you require any additional information concerning

Brooks products and services, please contact your local Brooks Sales and Service Ofce listed on the back cover

of this manual or visit www.BrooksInstrument.com.

Yours sincerely,

Brooks Instrument

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Paragraph Page

Number Number

Section 1 Introduction

1-1 Introduction......................................................................................................................................1-1

1-2 Intended Use ...................................................................................................................................1-2

1-3 Notice and Caution Statements.......................................................................................................1-2

1-4 Product Description Code ...............................................................................................................1-2

1-5 SolidSense II Pressure Transducer Specications..........................................................................1-5

Section 2 Installation

2-1 General............................................................................................................................................2-1

2-2 Receipt of Equipment ......................................................................................................................2-1

2-3 Recommended Storage Practice ....................................................................................................2-1

2-4 Return Shipment .............................................................................................................................2-1

2-5 Transit Precautions .........................................................................................................................2-2

2-6 Removal from Storage ....................................................................................................................2-2

2-7 Mechanical Connections .................................................................................................................2-2

2-8 Electrical Connections .....................................................................................................................2-3

2-9 Installation Instructions - Non-Incendive Field Wiring .....................................................................2-6

2-9-1 Non-Incendive Field Wiring 4-20 mA .............................................................................................2-6

2-9-2 Non-Incendive Field Wiring 0-5 Vdc ..............................................................................................2-7

2-10 Zero Adjustment ..............................................................................................................................2-8

2-10-1 .................................................................................................................................................... Zero

Adjustment (SolidSense II Standard Pressure Transducers) .......................................................................2-8

2-10-2 Zero Adjustment (ATEX SolidSense II Standard Pressure Transmitters Only) ..............................2-9

2-10-3 Integrated Display Operation.........................................................................................................2-10

Appendix A: Essential Instructions ............................................................................................................ A-1

Warranty, Local Sales/Service Contact Information ........................................................................Back Cover

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figures

Figure Page

Number Number

1-1 SolidSense II Pressure Transducer Sample Congurations ...........................................................1-1

1-2 Dimensional Drawings - SolidSense II Series, SC: Surface Mount, 1.5” C-Seal ...........................1-7

1-3 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel, Male ................................1-7

1-4 Dimensional Drawings - SolidSense II Series, CS: Surface Mount, 1.125” C-Seal .......................1-8

1-5 Dimensional Drawings - SolidSense II Series, SF: Face Seal, Swivel, VCR, Female ...................1-8

1-6 Dimensional Drawings - SolidSense II Series, CH: 1.5” C-Seal, High Flow....................................1-9

1-7 Dimensional Drawings - SolidSense II Series, 4S: Tube Weld Stub, 1/4” OD ...............................1-9

1-8 Dimensional Drawings - SolidSense II Series, CD: Surface Mount, Longer Gland, 1.125” C-Seal 1-10

1-9 Dimensional Drawings - SolidSense II Series, NT: 1/4” Male NPT ...............................................1-10

1-10 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel Male ................................1-11

1-11 Dimensional Drawings - SolidSense II Series, VS: Face Seal, Fixed Male/Swivel Female ...........1-11

1-12 Dimensional Drawings - SolidSense II Series, 4A: Micro-Fit Tee, 3/8” Branch X 1/4” Run ............1-12

1-13 Dimensional Drawings - SolidSense II Series, VM: Face Seal, Fixed Male ...................................1-12

1-14 Dimensional Drawings - SolidSense II Series, Single End (GID) and Flow Through (GIF)

Integrated Display Models ........................................................................................................1-13

1-15 Dimensional Drawings - SolidSense II ATEX Pressure Transmitter (Option) .................................1-14

2-1 4-20 mA Pinouts ..............................................................................................................................2-4

2-2 Voltage Output Pinouts....................................................................................................................2-4

2-3a 4-20 mA Output Device Wiring to LR056 ........................................................................................2-5

2-3b Integrated Display Electrical Connections .......................................................................................2-5

2-4 Non-Incendive Field Wiring for 4-20 mA..........................................................................................2-6

2-5 Non-Incendive Field Wiring for 0-5 Vdc...........................................................................................2-7

2-6 Location of the Zero Adjustment Screw on the Standard SolidSense II Pressure Transducers .....2-8

2-7 Location of the Zero Adjustment Screw on the ATEX SolidSense II Pressure Transmitters ...........2-9

2-8 Proper Wrench/Leverage Points for SolidSense II Devices ............................................................2-9

2-9 Location of the Zero Adjustment Screw on the Integrated Display SolidSense II Pressure Transmitters

2-10

Table Page

Number Number

1-1 Optional Cables for SolidSense II - Standard..................................................................................1-2

1-2 Product Description Code for SolidSense II - Standard ..................................................................1-3

1-3 Product Description Code for SolidSense II - ATEX ........................................................................1-4

1-4 Specications ..................................................................................................................................1-5

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

1-1 Introduction

This manual covers the Brooks

®

SolidSense II

®

Series pressure

transducers as shown in Figure 1-1 below. Included herein is general

information, operating specications, installation, removal instructions

and product warranty information.

This manual is organized into the following sections:

Section 1 - Introduction

Section 2 - Installation

Section A - Essential Instructions

Back Cover - Limited Warranty and Contacts

It is recommended that this manual be read in its entirety before

attempting to operate the Brooks SolidSense II Series devices.

Figure 1-1 SolidSense II Pressure Transducer Sample Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

1-2 Intended Use

The Brooks SolidSense II Series pressure transducers meet the most rigid

semiconductor and industrial high purity application requirements. With

accuracy of 0.25% of full scale, SolidSense II pressure transducers are used

to provide years of reliable pressure monitoring in a variety of applications.

The SolidSense II Series pressure transducers have one of the smallest

footprints in the industry for quick and easy installation in the tightest areas.

1-3 Notice and Caution Statements

Warning, caution and notice statements are located throughout this manual

in the ANSI format.

A WARNING statement indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

A CAUTION statement indicates a potentially hazardous situation which, if

not avoided, MAY result in minor or moderate injury. It may also be used to

alert against unsafe practices.

A NOTICE statement describes specic information that requires special

attention.

1-4 Product Description Code

The following Product Description Code (PDC) identies the SolidSense II

pressure transducer in various congurations Reference Tables 1-1 thru 1-3.

This code is used to order your SolidSense II pressure transducer. Call your

Brooks Service and Support Representative if you need assistance.

Table 1-1 Optional Cables for SolidSense II - Standard

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Table 1-2 Product Description Code for SolidSense II - Standard

SampleSample

Sample

Model CodeModel Code

Model Code

Code DescriptionCode Description

Code Description

Code OptionCode Option

Code Option

Option DescriptionOption Description

Option Description

I.I.

I. Base Model Code

GFGF

GF Pressure Transducer

GIGI

GI Pressure Transducer with integrated display

II.II.

II. Body Type

DD

D Dead End

FF

F Flow Through

III.III.

III. PSI

0000

00 30

0101

01 100

0202

02 250

X2X2

X2 235

0505

05 500

1010

10 1000

2525

25 2500

3030

30 3000

6060

60 60

1515

15 1500 Torr

IV.IV.

IV. Pressure Reference

AA

A Absolute, psi

CC

C Compound, psi

GG

G Gauge, psi

BB

B Absolute, Bar

PP

P Compound, Bar

SS

S Gauge, Bar

TT

T Absolute Torr

V.V.

V. Output

33

3 0.00 to 10.00 Vdc

44

44 to 20 mA

55

5 0.05 to 5.05 Vdc

66

6 0.2 to 5.2 Vdc

77

72 to 10 Vdc

88

8 No signal output (GI model with display only)

VI.VI.

VI. Electrical Connection GFF GFD GIF GID

AA

A4 ft Pigtail with AMP

®

Connector (3-pin) - Current Output Only

xx

BB

B Bendix

®

Connector xx

DD

D 15 Pin HD D-Sub Connector - Voltage Output Only xx

EE

E9 inch Pigtail with 15 Pin (Standard) D-Sub Connector - Voltage Output Only

xxxx

GG

G4 ft Pigtail with AMP

®

Connector (4-pin) - Voltage Output Only

xx

HH

H6 inch Pigtail with Molex

®

Connector

xx

KK

K 9-pin D-Sub - Voltage Output Only xx

LL

L 10 ft (3m) Pigtail

xxxx

MM

M5 inch (0.127m) Pigtail with AMP

®

Connector (4-pin) - Voltage Output Only

xx

NN

N 16.5 ft cable with Bendix

®

Type (Bayonet)

xxxx

PP

P6 ft (2m) Pigtail

xxxx

RR

R8 inch Pigtail with AMP

®

Connector (4-pin)

xx

SS

S 2m (79”) Pigtail with 9-Pin D Connector - Current Output Only xx

VV

V 18 inch Pigtail with 6-pin Molex

®

Connector

xx

WW

W2 inch Pigtail with AMP

®

Connector (4-pin) plus 1” strain relief (+/- 1/8”) at

xx

20° angle from bottom dead center

ZZ

Z 36 inch Pigtail ith Bendix

®

Connector (Bayonet)

xxxx

VII.VII.

VII. Fittings GFF GFD GIF GID

4S*4S*

4S* Tube Weld Stub 1/4” O.D. x

4T*4T*

4T* Duncan T, 1/4” Tube Weld Stub x

CDCD

CD Surface Mount, 1.125” C-Seal, 0.5” longer gland

xx

CHCH

CH Surface Mount, 1.5” C-Seal, High Flow K1H x

CSCS

CS Surface Mount, 1.125” C-Seal, Standard

xx

NTNT

NT 1/4” NPT x

SCSC

SC Surface Mount, 1.5” C-Seal x

SFSF

SF Face Seal, swivel female

xxxx

SMSM

SM Face Seal, swivel male

xxxx

VMVM

VM Face Seal, xed male x x

VSVS

VS Face Seal, xed male/swivel female on Duncan

Tx

II

I

IIII

II

IIIIII

III

IVIV

IV

VV

V

VIVI

VI

VIIVII

VII

GFGF

GF

FF

F

0202

02

CC

C

44

4

PP

P

SFSF

SF

* Tube stubs (4S and 4T) are not suitable for compression joint.

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Table 1-3 Product Description Code for SolidSense II - ATEX

Sample Model CodeSample Model Code

Sample Model Code

II

I

IIII

II

IIIIII

III

IVIV

IV

VV

V

VIVI

VI

VIIVII

VII

VIIIVIII

VIII

GFGF

GF

FF

F

0202

02

CC

C

44

4

PP

P

SFSF

SF

AA

A

Code DescriptionCode Description

Code Description

Code OptionCode Option

Code Option

Option DescriptionOption Description

Option Description

I.I.

I. Base Model Code

GFGF

GF Pressure Transducer

II.II.

II. Body Type

DD

D Dead End

FF

F Flow Through

III.III.

III. PSI

0000

00 30

0101

01 100

0202

02 250

0505

05 500

1010

10 1000

2525

25 2500

3030

30 3000

1515

15 1500 Torr

IV.IV.

IV. Pressure Reference

AA

A Absolute, psi

CC

C Compound, psi

GG

G Gauge, psi

BB

B Absolute, Bar

PP

P Compound, Bar

SS

S Gauge, Bar

TT

T Torr

V.V.

V. Output

44

44 to 20 mA

55

5 0.05 to 5.05 Vdc

VI.VI.

VI. Electrical Connection

PP

P 2m Pigtail

LL

L 3m Pigtail

EE

E9 inch Pigtail w/15-pin (standard) D-sub Connectors

NN

N 16.5 foot cable with Bendix

®

Type (Bayonet)

VII.VII.

VII. Fittings

4S4S

4S Tube Weld Stub 1/4” O.D. (GFD Only)*

CSCS

CS Surface Mount, 1.125” C-Seal, Standard (GFD Only)

CHCH

CH Surface Mount, 1.5” C-Seal, High Flow K1H (GFD Only)

SCSC

SC Surface Mount, 1.5” C-Seal (GFD Only)

NTNT

NT

NT 1/4” NPT (GFD only)

VMVM

VM Face Seal, fixed male (x2 on Duncan T for GFF)

VSVS

VS Face Seal, fixed male/swivel female on Duncan T (GFF Only)

SMSM

SM Face Seal, swivel male (x2 on Duncan T for GFF)

SFSF

SF Face Seal, swivel female (x2 on Duncan T for GFF)

4T4T

4T Duncan T, 1/4” Tube Weld Stub (GFF Only)*

VIII.VIII.

VIII.Explosion Proof

AA

A FM and ATEX approved

* Tube stubs (4S and 4T) are not suitable for compression joint.

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

1-5 SolidSense II Pressure Transducer Specications

Performance Non-Display Version Display Version

Temperature:

Operating: -20

O

F to 180

O

F (-29

O

C to 82

O

C) -20°F to 140°F (-29°C to 60°C)

Storage: -40

O

F to 180

O

F (-40

O

C to 82

O

C) -40°F to 167°F (-40°C to 75°C)

Compensated: -4

O

F to 140

O

F (-20

O

C to 60

O

C) / 68

O

F to 140

O

F (20

O

C to 60

O

C) 0-10 Vdc version

Burst Pressure: 400% full scale

Proof Pressure: 200% full scale up to 2,000 psi, 150% full scale for higher ranges

Accuracy: 0.25% full scale (BFSL)

Response Time: < 5 msec

Zero and Span Temperature

Coecient (each):

>100 PSI Ranges Full Scale: +0.02% full scale/

O

F (-4

O

F to 140

O

F, -20

O

C to 60

O

C)

+0.50% full scale (68

O

F to 140

O

F, 20

O

C to 60

O

C) 0 to 10 Vdc version

<100 PSI Ranges Full Scale: +0.04% full scale/

O

F (-4

O

F to 140

O

F, -20

O

C to 60

O

C)

+1.00% full scale (68

O

F to 140

O

F, 20

O

C to 60

O

C) 0 to 10 Vdc version

Mechanical

Housing: Stainless steel, polymer plastics

Wetted Parts: VIM-VAR 316L stainless steel, SEMI F20

Surface Finish: Compliant with SEMI F19

Cleanliness: Compliant to ASTM F1374-92 (2005)

Internal Volume: 1.79cc

Process Connections: (See Product Congurations for available options)

Approximate Shipping Weight: 0.70 lb. (0.32 kg)

Electrical Non-Display Version Display Version

Supply Current: Max. 10 mA Max. 30 mA

Power Requirements: 10 to 30 Vdc for 4 to 20 mA output 15 to 30 Vdc for 4 to 20 mA output and no signal output

11 to 30 Vdc for 0 to 5 Vdc output 11 to 30 Vdc for 0 to 5 Vdc output

13 to 32 Vdc for 0 to 10 Vdc output 13 to 30 Vdc for 0 to 10 Vdc output

Electrical Connections: Code B Bendix

®

connector

(See Tables 1-1 & 1-2 for Code P Pigtail 6 ft long

full list) Code D 15-pin HD D-sub connector

Code K 9-pin D-sub

Code A 4 ft pigtail with AMP

®

connector (3 pin)

Code G 4 ft pigtail with AMP

®

connector (4 pin)

Code H 6 inch pigtail with Molex

®

connector

Electrical Protection: Reverse polarity for power connections

Table 1-4 Specications

Specications continued on next page.

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Optional Display Non-Display Version Display Version

Digits: N/A -xxx to 1xxx

Type: N/A 7 Segment Red LED

Polarity: N/A Automatic (-) Display

Over Pressure Reading Trigger: N/A 110% full scale ± 5% full scale (Display reading: 1---)

Display Accuracy: N/A ±-0.25% of Rdg ± 1 Count for psi

(excluding transducer output) N/A ± - 0.25% of Rdg ± 5 Count for kPa

Character Size: N/A 0.30” height

kPa/psi Switch: N/A Yes

Rotatable: N/A Continuous rotation covering 4 quadrants

Zero Pot: N/A Yes

Zero Pot Adj. Screwdriver: N/A 1-1.2 mm at type

Approvals and Compliance

FM Approval: Non-Incendive for use in Class I, Div II Groups A, B, C and D Hazardous Applications

Excludes 0 to 10 Vdc and 15-pin HD D-Sub connector congurations

EMC: Compliant to EU Directive 2004/108/EC

RoHS: Compliant to EU Directive 2002/95/EC

Table 1-4 Specications (Continued)

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-3 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel, Male

Figure 1-2 Dimensional Drawings - SolidSense II Series, SC: Surface Mount, 1.5” C-Seal

GFD Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-5 Dimensional Drawings - SolidSense II Series, SF: Face Seal, Swivel, VCR, Female

Figure 1-4 Dimensional Drawings - SolidSense II Series, CS: Surface Mount, 1.125” C-Seal

GFD Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-7 Dimensional Drawings - SolidSense II Series, 4S: Tube Weld Stub, 1/4” OD

Figure 1-6 Dimensional Drawings - SolidSense II Series, CH: 1.5” C-Seal, High Flow

GFD Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-9 Dimensional Drawings - SolidSense II Series, NT: 1/4” Male NPT

Figure 1-8 Dimensional Drawings - SolidSense II Series, CD: Surface Mount, Longer Gland, 1.125” C-Seal

GFD Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-11 Dimensional Drawings - SolidSense II Series, VS: Face Seal, Fixed Male/Swivel Female

Figure 1-10 Dimensional Drawings - SolidSense II Series, SM: Face Seal, Swivel Male

GFF Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-13 Dimensional Drawings - SolidSense II Series, VM: Face Seal, Fixed Male

Figure 1-12 Dimensional Drawings - SolidSense II Series, 4A: Micro-Fit Tee, 3/8” Branch X 1/4” Run

GFF Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-14 Dimensional Drawings - SolidSense II Series, Single End (GID) and Flow Through (GIF) Integrated Display Models

GID & GIF Integrated Display Congurations

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

Figure 1-15 Dimensional Drawings - SolidSense II ATEX Pressure Transmitter (Option)

For more details on the SolidSense II ATEX compliant pressure

transmitters, visit our website at www.BrooksInstrument.com/Products

for the data sheet: DS-PR-SolidSense II ATEX-PT-eng or contact your

nearest Brooks Customer Service Center for assistance.

Note: Bendix, 15-pin and pigtail available on all ATEX process ttings. Limited examples are shown above.

For all electrical connection and tting options see the Model Code Table.

Additional dimensional drawings are available on request.

Installation and Operation Manual

X-PR-SolidSense II-PT-eng

Part Number: 541B160AAG

May, 2019

SolidSense II

®

Series

2-1 General

This section provides installation instructions for the Brooks

®

SolidSense II

pressure transducers. Refer to Section 1 of this manual for dimensions.

2-2 Receipt of Equipment

When the equipment is received, the outside packing case should be

checked for damage incurred during shipment. If the packing case is

damaged, the local carrier should be notied at once regarding his liability. A

report should be submitted to the nearest Brooks Instrument location listed

on the Global Service Network page on our website: BrooksInstrument.com/

GlobalSupportCenters

Remove the envelope containing the packing list. Carefully remove the

instrument from the packing case. Make sure spare parts are not discarded

with the packing materials. Inspect for damaged or missing parts.

2-3 Recommended Storage Practice

If intermediate or long-term storage of equipment is required, it is

recommended that the equipment be stored in accordance with the following:

a. Within the original shipping container.

b. Ambient temperature 21°C (70°F) nominal, 79°C (175°F) maximum

-29°C (-20°F) minimum.

c. Relative humidity 45% nominal, 60% maximum, 25% minimum.

2-4 Return Shipment

Prior to returning any instrument to the factory for any reason, visit our

website for instructions on how to obtain a Return Materials Authorization

Number (RMA #) and complete a Decontamination Statement to accompany

it: BrooksInstrument.com/Service. All instruments returned to Brooks also

require a Material Safety Data Sheet (MSDS) for the uid(s) used in the

instrument. Failure to provide this information will delay processing of the

instrument.

Instrument must have been purged in accordance with the following:

Pagina se încarcă ...

Brooks GF / GI Instrucțiuni de utilizare

Brooks GF / GI Instrucțiuni de utilizare

în alte limbi

Lucrări conexe

Alte documente