Asus H170I-PRO/CSM Manual de utilizare

Categorie
Plăci de bază
Tip
Manual de utilizare

Acest manual este potrivit și pentru

Motherboard
H170I-PRO
ii
E11627
First Edition
April 2016
Copyright © 2016 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data,
you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from http://support.asus.com/download
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notication to the email address [email protected], stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).
iii
Contents
Safety information ...................................................................................................... iv
About this guide ......................................................................................................... iv
Package contents ....................................................................................................... vi
H170I-PRO specifications summary ......................................................................... vi
Chapter 1 Product introduction
1.1 Before you proceed ......................................................................................1-1
1.2 Motherboard overview .................................................................................1-1
1.3 Central Processing Unit (CPU) ....................................................................1-9
1.4 System memory ..........................................................................................1-10
1.5 Wi-Fi antenna installation .......................................................................... 1-11
1.5 M.2 socket 3 installation ............................................................................1-12
Chapter 2 BIOS information
2.1 Managing and updating your BIOS .............................................................2-1
2.2 BIOS setup program .....................................................................................2-5
2.3 Exit menu ....................................................................................................2-10
Appendices
Notices ..................................................................................................................... A-1
iv
Safety information
Electrical safety
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your retailer.
Operation safety
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
Before using the product, ensure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualied service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and conguring the
motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter1:Productintroduction
This chapter describes the features of the motherboard and the new technology it
supports.
• Chapter2:BIOSinformation
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
v
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty yers,
that may have been added by your dealer. These documents are not part of the
standard package.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task
IMPORTANT: Instructions that you MUST follow to complete a task. .
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
vi
(continued on the next page)
H170I-PRO specifications summary
CPU
LGA1151 socket for 6th Generation Intel
®
Core
TM
, Pentium
®
, and Celeron
®
Processors
Supports 14nm CPU
Supports Intel
®
Turbo Boost Technology 2.0*
* Intel
®
Turbo Boost Technology 2.0 support depends on the CPU types.
** Refer to www.asus.com for Intel
®
CPU support list.
Chipset
Intel
®
H170 Chipset
Memory
2 x DIMM, max. 32GB, DDR4 2133MHz, non-ECC, un-buffered memory modules
Dual-channel memory architecture
Supports Intel
®
Extreme Memory Prole (XMP)
* Due to Intel® chipset limitation, DDR4 2133 MHz and higher memory modules on
XMP mode will run at the maximum transfer rate of DDR4 2133 Mhz.
** Refer to www.asus.com for the latest Memory QVL (Qualified Vendors List).
*** The maximum memory frequency supported varies by processor.
Expansion slots
1 x PCI Express 3.0/2.0 x16 slot (at x16 mode)
VGA
Integrated Graphics Processor - Intel
®
HD Graphics support
Multi-VGA output support: DisplayPort, HDMI, DVI-D, D-sub
- Supports DisplayPort with max. resolution 4096 x 2304 @60Hz
- Supports HDMI with max. resolution 4096 x 2160 @24 Hz / 2560 x 1600
@60 Hz /1920 x 1080@ 120 Hz
- Supports DVI-D with max. resolution 1920x1200@60Hz
- Supports D-sub with max. resolution 1920x1200@60Hz
- Supports Intel® InTru™ 3D, Quick Sync Video, Clear Video HD Technology,
Insider™
Supports up to 3 displays simultaneously
Maximum shared memory of 1024MB
Storage
Intel
®
H170 Chipset with RAID 0, 1, 5, 10 and Intel
®
Rapid Storage Technology
14 support:
- 1 x SATA Express port (gray, compatible with 2 x SATA 6.0 Gb/s ports)
- 1 x M.2 Socket 3 with M key, type 2242*/2260/2280 storage devices support
(both SATA & PCIE x4 mode)
- 4 x SATA 6.0 Gb/s ports (gray, 2 from SATA Express Port)
- Supports Intel
®
Smart Response Technology**
* Support with M.2 2242 mounting kit.
** These functions will work depending on the CPU installed.
Package contents
Check your motherboard package for the following items.
Motherboard
ASUS H170I-PRO motherboard
Cables 2 x Serial ATA 6.0 Gb/s cables
Accessories
1 x I/O shield 1 x M.2 2242 Mounting kit
1 x M.2 Screw package 1 x CPU installation tool
1 x Wi-Fi 2T2R Antenna
Application DVD Support DVD
Documentation User Guide
If any of the above items is damaged or missing, contact your retailer.
vii
H170I-PRO specifications summary
LAN
Intel
®
Gigabit LAN
Realtek
®
Gigabit LAN
Anti-surge LANGuard
Wireless
Speedy Wi-Fi 802.11 a/b/g/n/ac supports dual frequency band 2.4/5 GHz with MU-
MIMO support
Bluetooth
Audio
Realtek
®
ALC887 8-channel High Denition Audio CODEC with ASUS Audio
Feature
- Separate layer for left and right track, ensuring both sound deliver equal quality
- Top notch audio sensation delivers according to the audio conguration
- Premium Japan-made audio capacitors provides warm, natural, and immersive
sound with exceptional clarity and delity
- Supports jack-detection, multi-recording, front panel jack-retasking
- Optical S/PDIF out port at back I/O
USB
Intel
®
H170 Chipset
- 8 x USB 3.0/2.0 ports (2 ports at mid-board; 6 ports at back panel, blue)
- 4 x USB 2.0/1.1 ports (4 ports at mid-board)
ASUS
unique
features
ASUS 5X Protection II
- ASUS DIGI+ VRM
- ASUS Enhanced DRAM Overcurrent Protection - Short circuit damage
prevention
- ASUS Overvoltage Protection - World-class circuit-protection power design
- ASUS LANGuard - Protects against LAN surges, lightning strikes
- ASUS Stainless Steel Back I/O - 3x more durable corrosion-resistant coating
ASUS EPU
- EPU
Fan Xpert 2+
- Featuring Fan Auto Tuning function and multiple thermistors selection for
optimized system cooling control
Media Streamer
- Pipe music or movies from your PC to a smart TV, your entertainment goes
wherever you go!
- Media Streamer app for portable smartphone/tablet, supporting iOS 7 &
Android 4.0 systems
EZ DIY
Push Notice
- Monitor your PC status with smart devices in real time
UEFI BIOS EZ Mode featuring friendly graphics user interface
- CrashFree BIOS 3
- EZ Flash 3
ASUS Q-Design
- ASUS Q-DIMM
ASUSExclusiveFeatures:
- USB 3.0 Boost featuring speedy USB 3.0 transmission
- ASUS AI Suite 3
- Disk Unlocker
(continued on the next page)
viii
H170I-PRO specifications summary
Specications are subject to change without notice.
ASUS unique
features
- Wi Go!
- ASUS AI Charger
Back Panel I/O
ports
1 x PS/2 keyboard / mouse combo port
1 x D-SUB
1 x DVI-D
1 x DisplayPort
1 x HDMI port
2 x Wi-Fi antenna ports
1 x Optical S/PDIF out
2 x LAN (RJ45) ports
6 x USB 3.0/2.0 ports (blue)
3-Jack 8-Channel Audio I/O ports
Internal I/O
connectors
1 x 19-pin USB 3.0/2.0 connector supports additional 2 USB 3.0/2.0 ports
2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1 ports
1 x System panel headerr
1 x Front panel audio connector (AAFP)
4 x SATA 6.0 Gb/s connectors (gray, 2 from SATA Express Port)
1 x M.2 Socket 3 for M Key, type 2242/2260/2280 devices
1 x SATA Express connector: gray, compatible with 2 x SATA 6.0 Gb/s ports
1 x CPU fan connector (4-pin)
2 x Chassis Fan connectors (4-pin) for both 3-pin(DC mode) and 4-pin
(PWM mode) coolers control
1 x TPM header
1 x speaker header
1 x COM header
1 x 24-pin EATX Power connector
1 x 4-pin EATX 12V Power connector
1 x Clear CMOS jumper (2-pin)
BIOS features
128 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI 3.0, WfM 2.0, SM BIOS
3.0, ACPI 5.0, Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS
3, F6 Qfan Control, F3 My Favorites, F9 Quick Note, Last Modied Log,
F12 PrintScreen function, and ASUS DRAM SPD (Serial Presence Detect)
memory information
Manageability
WfM 2.0, DMI 3.0, WOL by PME, PXE
Support DVD Drivers
ASUS utilities
EZ Update
Anti-virus software (OEM version)
Operating System
Support
Windows
®
10*
Windows
®
8.1* / Windows
®
8
Windows
®
7
*64-bit support only
Form factor
Mini-ITX Form Factor, 6.7”x 6.7” (17cm x 17cm)
ASUS H170I-PRO
1-1
Product introduction
1
1.1 Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
• Unplugthepowercordfromthewallsocketbeforetouchinganycomponent.
• Beforehandlingcomponents,useagroundedwriststraportouchasafelygrounded
objectorametalobject,suchasthepowersupplycase,toavoiddamagingthemdue
to static electricity.
• Beforeyouinstallorremoveanycomponent,ensurethattheATXpowersupplyis
switched off or the power cord is detached from the power supply. Failure to do so
maycauseseveredamagetothemotherboard,peripherals,orcomponents.
Unplugthepowercordbeforeinstallingorremovingthemotherboard.Failuretodosocan
cause you physical injury and damage motherboard components.
H170I-PRO
Super
I/O
ALC
887
17.0cm(6.7in)
17.0cm(6.7in)
DDR4_DIMM_A1 (64bit, 288-pin module)
DDR4_DIMM_B1 (64bit, 288-pin module)
EATX_PWR
AUDIO
AAFP
COM
ASM
1442K
BATT_CON
CPU_FAN
CHA_FAN1
CHA_FAN2
SATA6G_1 SATA6G_2
M.2(SOCKET3)
Intel
®
H170
SATAEXPRESS
PCIEX16
CLRTC
SPEAKER
SPDIF_OUT
I219V
LAN1_USB3_34
LAN2_USB3_56
KBMS_USB3_78
DVI
VGA
128Mb
BIOS
LGA1151
USB3_12
USB910
F_PANEL
USB1112
ATX12V
TPM
Wi-Fi GO!
SPDIFO
_HDMI
_DP
1 2
8
9
10
2
7
113 12
15
14
3 4
11
8
16
17
5 6
1.2 Motherboard overview
Place this
side towards
the rear of the
chassis
1-2
Chapter 1: Product introduction
1.2.1 Layout contents
Connectors/Jumpers/Slots/LED
Page
1.
CPUandchassisfanconnectors(4-pinCPU_FAN,4-pinCHA_FAN1/2) 1-2
2.
ATXpowerconnectors(24-pinEATXPWR,4-pinEATX12V) 1-2
3. Intel
®
LGA1151CPUsocket 1-3
4. ClearRTCRAM(2-pinCLRTC) 1-3
5. DDR4DIMMslots 1-3
6. Speakerconnector(4-pinSPEAKER) 1-4
7. Systempanelconnector(10-1pinF-PANEL) 1-4
8. Intel(R)H170SerialATA6Gb/sconnectors(7pinSATA6G_3~6,SATAEXPRESS) 1-4
9. USB2.0connector(10-1pinUSB910,USB1112) 1-4
10. USB3.0connector(20-1pinUSB3_12) 1-5
11. M.2Socket3 1-5
12. PCIExpress3.0/2.0x16slot 1-5
13. Digitalaudioconnector(4-1pinSPDIF_OUT) 1-5
14. Frontpanelaudioconnector(10-1pinAAFP) 1-6
15 TPMHeader(14-1pinTPM) 1-6
16 Serialportconnector(10-1pinCOM) 1-6
17 RTCbatteryheader(2-pinBATT_CON) 1-6
2. ATX power connectors (24-pin EATXPWR, 4-pin EATX12V)
TheseconnectorsareforATXpowersupplyplugs.Thepowersupplyplugsare
designedtottheseconnectorsinonlyoneorientation.Findtheproperorientationand
pushdownrmlyuntiltheconnectorscompletelyt.
1. CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1/2)
Connectthefancablestothefanconnectorsonthemotherboard,ensuringthatthe
black wire of each cable matches the ground pin of the connector.
CHA FAN PWM
CHA FAN IN
CHA FAN PWR
GND
CPU_FAN
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
CHA_FAN
Do not forget to connect the fan cables to the fan connectors.
Insufcientairowinsidethesystemmaydamagethe
motherboard components. These are not jumpers! Do not place
jumpercapsonthefanconnectors!TheCPU_FANconnector
supportsaCPUfanofmaximum1A(12W)fanpower.
Onlythe4-pinCPUfansupportstheASUSFanXpert2+feature.
ASUS H170I-PRO
1-3
•
WerecommendthatyouuseanEATX12VSpecication
2.0-compliantpowersupplyunit(PSU)withaminimumof300W
powerrating.ThisPSUtypehas24-pinand8-pinpowerplugs.
•
DONOTforgettoconnectthe4-pinEATX+12Vpowerplug.
Otherwise,thesystemwillnotbootup.
• WerecommendthatyouuseaPSUwithhigherpoweroutput
whenconguringasystemwithmorepower-consumingdevices
orwhenyouintendtoinstalladditionaldevices.Thesystemmay
become unstable or may not boot up if the power is inadequate.
•
If you are uncertain about the minimum power supply
requirementforyoursystem,refertotheRecommended
PowerSupplyWattageCalculatorathttp://support.asus.com/
PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for
details.
EATXPWR
PIN 1
GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
GND
GND
PSON#
GND
-12 Volts
+3 Volts
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
GND
+5 Volts
GND
+5 Volts
GND
+3 Volts
+3 Volts
EATX12V
PIN 1
+12V DC
+12V DC
GND
GND
5. DDR4 DIMM slots
Install2GB,4GB,8GB,and16GBunbufferednon-ECCDDR4DIMMsintothese
DIMMsockets.
Formoredetails,refertoSystem memory.
3. Intel
®
LGA1151 CPU socket
ThismotherboardcomeswithasurfacemountLGA1151socketdesignedforthe
6thGenerationIntel(R)Core(TM)i7/Core(TM)i5/Core(TM)i3,Pentium(R)and
Celeron(R)processors.
Formoredetails,refertoCentral Processing Unit (CPU).
To erase the RTC RAM:
1. TurnOFFthecomputerandunplugthepowercord.
2. Useametalobjectsuchasascrewdrivertoshortthetwopins.
3. PlugthepowercordandturnONthecomputer.
4. Holddownthe<Del>keyduringthebootprocessandenterBIOS
setup to re-enter data.
Ifthestepsabovedonothelp,removetheonboardbatteryandshortthetwopinsagainto
cleartheCMOSRTCRAMdata.AfterclearingtheCMOS,reinstallthebattery.
CLRTC
+3V_BAT
GND
PIN 1
4. Clear RTC RAM (2-pin CLRTC)
ThisheaderallowsyoutocleartheRealTimeClock(RTC)RAMinCMOS.Youcan
cleartheCMOSmemoryofdate,andsystemsetupparametersbyerasingtheCMOS
RTCRAMdata.TheonboardbuttoncellbatterypowerstheRAMdatainCMOS,which
include system setup information such as system passwords.
1-4
Chapter 1: Product introduction
9. USB 2.0 connector (10-1 pin USB910, USB1112)
ThisconnectorisforUSB2.0ports.ConnecttheUSBmodulecable
toanyofthisconnector,theninstallthemoduletoaslotopeningat
thebackofthesystemchassis.TheseUSBconnectorscomplywith
USB2.0specicationsandsupportsupto480Mbpsconnection
speed.
USB+5V
USB_P11-
USB_P11+
GND
NC
USB+5V
USB_P12-
USB_P12+
GND
USB1112
PIN 1
6. Speaker connector (4-pin SPEAKER)
The4-pinconnectorisforthechassis-mountedsystemwarningspeaker.
The speaker allows you hear system beeps and warnings.
+5V
GND
GND
Speaker Out
SPEAKER
PIN 1
7. System panel connector (10-1 pin F_PANEL)
Thisconnectorsupportsseveralchassis-mountedfunctions.
PIN 1
PWR BTN
PWR_LED+
PWR_LED-
PWR
GND
HDD_LED+
HDD_LED-
Ground
HWRST#
(NC)
F_PANEL
+PWR LED
+HDD_LED RESET
• SystempowerLED(2-pinPWR_LED)
This2-pinconnectorisforthesystempowerLED.Connectthe
chassispowerLEDcabletothisconnector.Thesystempower
LEDlightsupwhenyouturnonthesystempower,andblinks
when the system is in sleep mode.
• HarddiskdriveactivityLED(2-pinHDD_LED)
This2-pinconnectorisfortheHDDActivityLED.Connectthe
HDDActivityLEDcabletothisconnector.TheHDDLEDlights
uporasheswhendataisreadfromorwrittentotheHDD.
• ATXpowerbutton/soft-offbutton(2-pinPWR_BTN)
This connector is for the system power button.
• Resetbutton(2-pinRESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot
without turning off the system power.
8. Intel(R) H170 Serial ATA 6Gb/s connectors (7 pin SATA6G_3~6, SATAEXPRESS)
TheseconnectorsconnecttoSerialATA6.0Gb/sharddiskdrivesvia
SerialATA6.0Gb/ssignalcables.
IfyouinstalledSerialATAharddiskdrives,youcancreateaRAID0,
1,5,and10congurationwiththeIntel
®
RapidStorageTechnology
through the onboard Intel
®
H170chipset.
• Theseconnectorsaresetto[AHCI] by default. If you intend to
createaSerialATARAIDsetusingtheseconnectors,setthe
SATAModeitemintheBIOSto[RAID].
• BeforecreatingaRAIDset,refertothemanualbundledinthe
motherboardsupportDVD.
• TheSATAEXPRESSconnectorcansupportoneSATAExpress
deviceortwoSATAdevices.
SATAEXPRESS
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
RSATA_RXP1
GND
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
Floating
Device_Reset
GND
Detection
SATA6G
GND
RSATA_RXP4
RSATA_RXN4
GND
RSATA_TXN4
RSATA_TXP4
GND
ASUS H170I-PRO
1-5
10. USB 3.0 connector (20-1 pin USB3_12)
ThisconnectorallowsyoutoconnectaUSB3.0module
foradditionalUSB3.0frontorrearpanelports.Withan
installedUSB3.0module,youcanenjoyallthebenets
ofUSB3.0includingfasterdatatransferspeedsofup
to5Gbps,fasterchargingtimeforUSB-chargeable
devices,optimizedpowerefciencyandbackward
compatibilitywithUSB2.0.
USB3_12
GND
IntA_P1_D+
IntA_P1_D-
GND
IntA_P1_SSTX+
IntA_P1_SSTX-
GND
IntA_P1_SSRX+
IntA_P1_SSRX-
USB3+5V
PIN 1
IntA_P2_D+
IntA_P2_D-
GND
IntA_P2_SSTX+
IntA_P2_SSTX-
GND
IntA_P2_SSRX+
IntA_P2_SSRX-
USB3+5V
• ThissocketsupportsMKeyand2242/2260/2280storage
devices.
• WhentheM.2Socket3isoperatinginSATAmode,SATAport1
will be disabled.
• M.2SocketandPCIeX16_2connectorsupportPCIemodeand
sharebandwidth.Bydefault,thedevicedetectionpriorityofthe
systemisasfollows:SATAModeM.2>PCIeX16_2connector.
• WhenusingIntel
®
DesktopResponsivenesstechnologieswith
PCIeM.2device,ensuretosetuptheWindows
®
UEFIoperating
systemunderRAIDmode.
11. M.2 socket 3
This socket allows you to install an M.2(NGFF)SSDmodule.
M.2(SOCKET3)
12. PCI Express 3.0/2.0 x16 slot
ThismotherboardsupportsonePCIExpress3.0/2.0x16graphiccardthatcomplywith
thePCIExpressspecications.
A B C
D
VGA shared
USB3.0Controller shared
SATAController shared
HDController shared
IntelLAN shared
Realtek8111Hlan shared
IRQ assignments for this motherboard
WhenusingPCIcardsonsharedslots,ensurethatthedriverssupport“ShareIRQ”orthat
thecardsdonotneedIRQassignments.Otherwise,conictswillarisebetweenthetwoPCI
groups,makingthesystemunstableandthecardinoperable.
Neverconnecta1394cabletotheUSBconnectors.Doingsowilldamagethe
motherboard!
1-6
Chapter 1: Product introduction
14. Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio
I/OmodulethatsupportseitherHDAudioorlegacyAC`97
audio standard. Connect one end of the front panel audio
I/Omodulecabletothisconnector.
AAFP
AGND
NC
SENSE1_RETUR
SENSE2_RETUR
PORT1 L
PORT1 R
PORT2 R
SENSE_SEND
PORT2 L
HD-audio-compliant
pin definition
PIN 1
AGND
NC
NC
NC
MIC2
MICPWR
Line out_R
NC
Line out_L
Legacy AC’97
compliant definition
• Werecommendthatyouconnectahigh-denition
frontpanelaudiomoduletothisconnectortoavailof
themotherboard’shigh-denitionaudiocapability.
• Ifyouwanttoconnectahigh-denitionfrontpanel
audiomoduletothisconnector,settheFront Panel
TypeitemintheBIOSsetupto[HD].Ifyouwantto
connectanAC’97frontpanelaudiomoduletothis
connector,settheitemto[AC97].Bydefault,this
connectorissetto[HD].
13. Digital audio connector (4-1 pin SPDIF_OUT)
ThisconnectorisforanadditionalSony/PhilipsDigitalInterface(S/
PDIF)port.ConnecttheS/PDIFOutmodulecabletothisconnector,
then install the module to a slot opening at the back of the system
chassis.
SPDIF_OUT
+5V
SPDIFOUT
GND
15. TPM connector (14-1 pin TPM)
ThisconnectorsupportsaTrustedPlatformModule(TPM)system,
whichcansecurelystorekeys,digitalcerticates,passwords,anddata.
ATPMsystemalsohelpsenhancenetworksecurity,protectsdigital
identities,andensuresplatformintegrity.
TPM
PIN 1
+3VSB
S_PCIRST#_TBD
GND
C_PCICLK_TPM
+3V
+3V
PWRDWN
F_SERIRQ
F_FRAME#
F_LAD3
F_LAD2
F_LAD1
F_LAD0
16. Serial port connector (10-1 pin COM)
Thisconnectorisforaserial(COM)port.Connecttheserialport
modulecabletothisconnector,theninstallthemoduletoaslot
opening at the back of the system chassis.
PIN 1
COM
DCD
TXD
GND
RTS
RI
RXD
DTR
DSR
CTS
17. RTC Battery header (2-pin BATT_CON)
ThisconnectorisforthelithiumCMOSbattery.
ASUS H170I-PRO
1-7
1.2.2 Rear panel connectors
1. PS/2 Mouse/keyboard combo port.ThisportisforaPS/2mouseorkeyboard.
2. Video Graphics Adapter (VGA) port.This15-pinportisforaVGAmonitororother
VGA-compatibledevices.
3. Optical S/PDIF Out port.ThisportisforanopticalS/PDIFdevice.
4. LAN (RJ-45) ports.TheseportsallowGigabitconnectiontoaLocalAreaNetwork
(LAN)throughanetworkhub.RefertothetablebelowfortheLANportLED
indications.
2
6 74
89
451
9 11 10
3
12
LAN port
Speed
LED
Activity Link
LED
LAN port LED indications
Activity/Link LED Speed LED
Status Description Status Description
Off Nolink OFF 10Mbpsconnection
Orange Linked ORANGE 100Mbpsconnection
Orange(Blinking) Dataactivity GREEN 1Gbps connection
Orange(Blinking
thensteady)
Readytowake
upfromS5mode
5. Wi-Fi 802.11 a/b/g/n/ac Bluetooth V4.0/3.0 + HS port.TheseportsareforWi-Fi
networkorBluetoothdevices.
6. Line In port (light blue).Thisportconnectsthetape,CD,DVDplayer,orotheraudio
sources.
7. Line Out port (lime).Thisportconnectsaheadphoneoraspeaker.In4.1-channel,
5.1-channel,and7.1-channelcongurations,thefunctionofthisportbecomesFront
SpeakerOut.
8. Microphone port (pink). This port connects a microphone.
To configure a 7.1-channel audio output:
UseachassiswithHDaudiomoduleinthefrontpaneltosupporta7.1-channelaudio
output.
1-8
Chapter 1: Product introduction
9. USB 3.0 ports.These9-pinUniversalSerialBus(USB)portsconnecttoUSB3.0/2.0
devices.
• DuetoUSB3.0controllerlimitations,USB3.0devicescanonlybeusedundera
Windows
®
OSenvironmentandafterUSB3.0driverinstallation.
• ThepluggedUSB3.0devicemayrunonxHCIorEHCImode,dependingonthe
operating system’s setting.
• USB3.0devicescanonlybeusedfordatastorage.
• WestronglyrecommendthatyouconnectUSB3.0devicestoUSB3.0portsforfaster
andbetterperformancefromyourUSB3.0devices.
10. HDMI port.ThisportisforaHigh-DenitionMultimediaInterface(HDMI)connector,
andisHDCPcompliantallowingplaybackofHDDVD,Blu-ray,andotherprotected
content.
11. DisplayPort port.ThisportisforaDisplayPort-compatibledevices.
12. DVI-D port. ThisportisforanyDVI-Dcompatibledevice.DVI-Dcan’tbeconvertedto
outputRGBSignaltoCRTandisn’tcompatiblewithDVI-I.
Audio 2.1, 4.1, 5.1 or 7.1-channel configuration
Port
Headset
2.1-channel
4.1-channel 5.1-channel 7.1-channel
LightBlue
(Rearpanel)
Line In RearSpeakerOut RearSpeakerOut RearSpeakerOut
Lime(Rearpanel) LineOut FrontSpeakerOut FrontSpeakerOut FrontSpeakerOut
Pink(Rearpanel) MicIn MicIn Bass/Center Bass/Center
Lime(Frontpanel) SideSpeakerOut
Fora7.1-channelspeakersetup,refertothe7.1-channelcongurationinthetable.
ASUS H170I-PRO
1-9
1.3 Central Processing Unit (CPU)
ThismotherboardcomeswithasurfacemountLGA1151socket
designed for the 6th Generation Intel
®
Core™i7/Core™i5/Core™i3,
Pentium
®
and Celeron
®
processors.
UnplugallpowercablesbeforeinstallingtheCPU.
• EnsurethatyouinstallthecorrectCPUdesignedfortheLGA1151socketonly.DO
NOTinstallaCPUdesignedforLGA1150,LGA1155andLGA1156socketsonthe
LGA1151socket.
• Uponpurchaseofthemotherboard,ensurethatthePnPcapisonthesocketand
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
ismissing,orifyouseeanydamagetothePnPcap/socketcontacts/motherboard
components.
• Keepthecapafterinstallingthemotherboard.ASUSwillprocessReturnMerchandise
Authorization(RMA)requestsonlyifthemotherboardcomeswiththecaponthe
LGA1151socket.
• Theproductwarrantydoesnotcoverdamagetothesocketcontactsresultingfrom
incorrectCPUinstallation/removal,ormisplacement/loss/incorrectremovalofthePnP
cap.
Installing the CPU
1
4
ApplytheThermalInterfaceMaterialtotheCPUheatsinkandCPUbeforeyouinstallthe
heatsink and fan if necessary.
2
3
A
B
A
B
C
D
5
4
4
5
1-10
Chapter 1: Product introduction
1.4 System memory
Overview
ThismotherboardcomeswithtwoDoubleDataRate4(DDR4)DualInlineMemoryModule
(DIMM)sockets.ThegureillustratesthelocationoftheDDR4DIMMsockets:
Channel
Sockets
ChannelA DIMM_A1&DIMM_A2
ChannelB DIMM_B1&DIMM_B2
• YoumayinstallvaryingmemorysizesinChannelAandChannelB.Thesystem
mapsthetotalsizeofthelower-sizedchannelforthedual-channelconguration.Any
excessmemoryfromthehigher-sizedchannelisthenmappedforsingle-channel
operation.
• AlwaysinstallDIMMswiththesameCASlatency.Foroptimalcompatibility,we
recommendthatyouinstallmemorymodulesofthesameversionordatecode(D/C)
fromthesamevendor.Checkwiththeretailertogetthecorrectmemorymodules.
• DuetoIntel®chipsetlimitations,DDR42133MHzandhighermemorymoduleson
XMPmodewillrunatthemaximumtransferrateofDDR42133MHz.
• AccordingtoIntel
®
CPUspec,DIMMvoltagebelow1.35Visrecommendedtoprotect
theCPU.
• Duetothememoryaddresslimitationon32-bitWindows
®
OS,whenyouinstall4GB
ormorememoryonthemotherboard,theactualusablememoryfortheOScanbe
about3GBorless.Foreffectiveuseofmemory,werecommendthatyoudoanyofthe
following:
- Useamaximumof3GBsystemmemoryifyouareusinga32-bitWindows
®
OS.
- Installa64-bitWindows
®
OSifyouwanttoinstall4GBormoreonthe
motherboard.
- Formoredetails,refertotheMicrosoft
®
support site at http://support.microsoft.
com/kb/929605/en-us.
• Memorymoduleswithmemoryfrequencyhigherthan2133MHzanditscorresponding
timingortheloadedX.M.P.ProleisnottheJEDECmemorystandard.Thestability
andcompatibilityofthesememorymodulesdependontheCPU’scapabilitiesand
otherinstalleddevices.
• ThedefaultmemoryoperationfrequencyisdependentonitsSerialPresenceDetect
(SPD),whichisthestandardwayofaccessinginformationfromamemorymodule.
Underthedefaultstate,somememorymodulesforoverclockingmayoperateata
lowerfrequencythanthevendor-markedvalue.
• Forsystemstability,useamoreefcientmemorycoolingsystemtosupportafull
memoryload(2DIMMs).
• Refertowww.asus.comforthelatestMemoryQVL(QualiedVendorsList)
DIMM_A1
DIMM_B1
DIMM_B1
DIMM_B2
ASUS H170I-PRO
1-11
Installing a DIMM
1
2
To remove a DIMM
B
A
B
A
A
1.5 Wi-Fi antenna installation
ConnectthebundledASUS2T2RdualbandWi-FiantennaconnectortotheWi-Fiportsat
the back of the chassis.
IO Shield
• EnsurethattheASUS2T2RdualbandWi-FiantennaissecurelyinstalledtotheWi-Fi
ports.
• EnsurethatyouinstalltheBluetoothdriverbeforeinstallingtheWi-FiGO!software.
• Ensurethattheantennaisatleast20cmawayfromallpersons.
Theillustrationaboveisforreferenceonly.TheI/Oportlayoutmayvarywithmodels,but
theWi-Fiantennainstallationprocedureisthesameforallmodels.
1-12
Chapter 1: Product introduction
H170I-PRO M.2(SOCKET3)
M.2(SOCKET3)
H170I-PRO
1.5 M.2 socket 3 installation
This socket allows you to install an M.2(NGFF)SSDmodule.
• ThissocketsupportsMKeyand2242/2260/2280storagedevices.
• Fora2242storagedevice,usethebundled2242mountingkit.
• Beforeinstallinga2242M.2SSDmodule,ensurethatthemountingkitisproperly
installedwiththebiggerscrewholeonthe2260standoff.
• WhenusingIntel
®
DesktopResponsivenesstechnologieswithPCIeM.2device,
ensuretosetuptheWindows
®
UEFIoperatingsystemunderRAIDmode.
TheM.2(NGFF)SSDmoduleispurchasedseparately
2
3
1
To install a 2242 M.2 SSD module:
1. Alignthebiggerholeonthemountingkitwiththe2260
standoff and secure it with a screw.
2. Installthe2242M.2SSDmoduletotheM.2socket.
3. SecuretheM.2SSDmoduletotheM.2socketwitha
screw.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

Asus H170I-PRO/CSM Manual de utilizare

Categorie
Plăci de bază
Tip
Manual de utilizare
Acest manual este potrivit și pentru

în alte limbi