Tesla WDI461M Manual de utilizare

Categorie
Mașini de spălat vase
Tip
Manual de utilizare
Product images are for illustrative purposes only and may differ from the actual product.
DISHWASHER
WDI461M
User Manual
SRB
HR RO SLOENG
BiH/
CG
DISHWASHER
PART I: GENERIC VERSION
User Manual
Please read this manual carefully before using the dishwasher and
Keep this manual for future reference.
4
ENG
SAFETY INFORMATION
WARNING!
When using your dishwasher, follow the precautions
listed below:
Installation and repair can only be carried out by a
qualified technician
This appliance is intended to be used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential
type environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be done by children
without supervision. (For EN60335-1)
This appliance is not intended for use by persons
(including children ) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
(For IEC60335-1 ) Packaging material could be
dangerous for children!
This appliance is for indoor household use only.
To protect against the risk of electrical shock, do
not immerse the unit, cord or plug in water or
other liquid. Please unplug before cleaning and
performing maintenance on the appliance.
Use a soft cloth moistened with mild soap, and then
use a dry cloth to wipe it again.
Grounding Instructions
This appliance must be earthed. In the event of a
malfunction or breakdown, earthing will reduce
the risk of an electric shock by providing a path of
least resistance of electric current. This appliance is
equipped with an earthing conductor plug.
The plug must be plugged into an appropriate outlet
that is installed and earthed in accordance with all
local codes and ordinances.
Improper connection of the equipment-earthing
conductor can result in the risk of an electric
shock. Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
Do not modify the plug provided with the appliance;
If it does not fit the outlet.
Have a proper outlet installed by a qualified
electrician.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Open the door very carefully if the dishwasher is
operating, there is a risk of water squirting out. Do
not place any heavy objects on or stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;
2) Warning: Knives and other utensils with sharp
points must be loaded in the basket with their points
facing down or placed in a horizontal position.
Some dishwasher detergents are strongly alkaline.
They can be extremely dangerous if swallowed.
Avoid contact with the skin and eyes and keep
children away from the dishwasher when the door
is open.
Check that the detergent powder is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe” or the equivalent.
For unmarked plastic items not so marked, check the
manufacturer's recommendations.
Use only detergent and rinse agents recommended
for use in an automatic dishwasher.
Never use soap, laundry detergent, or hand washing
detergent in your dishwasher.
The door should not be left open, since this could
increase the risk of tripping.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
During installation, the power supply must not be
excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance needs to be connected to the main
water valve using new hose sets. Old sets should not
be reused.
To save energy, in stand by mode , the appliance
will switch off automatically while there is no any
operation in 15 minutes.
The maximum number of place settings to be
washed is 9.
The maximum permissible inlet water pressure is
1MPa.
The minimum permissible inlet water pressure is
0.04MPa.
Disposal
For disposing of package and the appliance please
go to a recycling center. Therefore cut off the power
supply cable and make the door closing device
unusable.
Cardboard packaging is manufactured from
recycled paper and should be disposed in the waste
paper collection for recycling.
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
5
ENG
for the environment and human health, which
could otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling of
this product, please contact your local city office and
your household waste disposal service.
DISPOSAL: Do not dispose this product as
unsorted municipal waste. Collection of such
waste separately for special treatment is
necessary.
PRODUCT OVERVIEW
IMPORTANT
To get the best performance from your dishwasher, read all operating instructions before using it for the first time.
NOTE
Pictures are only for reference; different models may be different.
Dispenser
Salt container
Inner pipe
Lower spray arm
Filter assembly
Cutlery basket Upper basket
Cup rack
Upper spray armCutlery rack
Lower basket
6
ENG
Inside Outside
USING YOUR DISHWASHER
Before using your dishwasher:
Always use salt intended for dishwasher use.
The salt container is located beneath the lower basket and should be filled as explained in the following:
WARNING!
Only use salt specifically designed for dishwashers use!
Every other type of salt not specifically designed for dishwasher use, especially table salt, will damage the water
softener. In case of damages caused by the use of unsuitable salt the manufacturer does not give any warranty
nor is liable for any damages caused.
Only fill with salt before running a cycle.
This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the
machine for any period of time, which may cause corrosion.
Please follow the steps below for adding dishwasher salt:
1. Remove the lower basket and unscrew the reservoir
cap.
2. Place the end of the funnel (supplied) into the hole
and pour in about 1.5kg of dishwasher salt.
3. Fill the salt container to its maximum limit with water,
It is normal for a small amount of water to come out
of the salt container.
4. After filling the container, screw back the cap tightly.
5. The salt warning light will stop being after the salt
container has been filled with salt.
6. Immediately after filling the salt into the salt
container, a washing program should be started
(We suggest to use a short program). Otherwise the
filter system, pump or other important parts of the
machine may be damaged by salty water. This is out
of warranty.
1. Set the water softener
2. Loading the salt Into the softener
3. Loading the basket
4. Fill the dispenser
Loading The Salt Into The Softener
NOTE
Please check the section 1 “Water Softener” of PART II: Special Version, If you need to set the water softener.
If your model does not have any water softener, you may skip this section.
NOTE
7
ENG
NOTE
The salt container must only be refilled when the salt warning light ( ) in the control panel comes on.
Depending on how well the salt dissolves, the salt warning light may still be on even though the salt container is
filled.
If there is no salt warning light in the control panel (for some Models), you can estimate when to fill the salt into
the softener by the cycles that the dishwasher has run.
If salt has spilled, run a soak or quick program to remove it.
Basket - user tips
Adjusting the upper basket
Type 1:
The height of the upper basket can be easily adjusted to accommodate taller dishes in either the upper or lower
basket.
To adjust the height of the upper rack, follow these steps:
Pull out upper basket. Remove upper basket.
Lower position
Upper position
Re-attach upper basket to the upper or lower rollers.
To raise the upper basket, just lift the upper basket
at the center of each side until the basket locks into
place in the upper position. It is not necessary to lift the
adjuster handle.
Push in upper basket.
To lower the upper basket, lift the adjust handles on
each side to release the basket and lower it to the lower
position.
Type 2:
8
ENG
NOTE
Pictures are only for reference, different models of the filtering system and spray arms may be different.
Folding back the cup shelves
To make room for taller items in the upper basket, raise the cup rack upwards. You can then lean the tall glasses
against it. You can also remove it when it is not required for use.
Folding back the rack shelves
The spikes are used for holding plates and a platter. They can be lowered to make more room for large items.
MAINTENANCE AND CLEANING
External Care
The door and door seal
Clean the door seals regularly with a soft damp cloth to remove food deposits.
When the dishwasher is being loaded, food and drink residues may drip onto the sides of the dishwasher door.
These surfaces are outside the wash cabinet and are not accessed by water from the spray arms. Any deposits
should be wiped off before the door is closed.
The control panel
If cleaning is required, the control panel should be wiped with a soft damp cloth only.
WARNING!
To avoid penetration of water into the door lock and electrical components, do not use a spray cleaner of any
kind.
Never use abrasive cleaners or scouring pads on the outer surfaces because they may scratch the finish. Some
paper towels may also scratch or leave marks on the surface.
Internal Care
Filtering system
The filtering system in the base of the wash cabinet retains coarse debris from the washing cycle. The collected
coarse debris may cause the filters to clog. Check the condition of the filters regularly and clean them if necessary
under running water. Follow the steps below to clean the filters in the wash cabinet.
raise upwards fold backwards
9
ENG
Main filter
Main filter
Hold the coarse filter and rotate it counterclockwise to
unlock the filter. Lift the filter upwards and out of the
dishwasher.
Larger food remnants can be cleaned by rinsing the
filter under running water. For a more thorough clean,
use a soft cleaning brush.
The fine filter can be pulled off the bottom of the filter
assembly. The coarse filter can be detached from the
main filter by gently squeezing the tabs at the top and
pulling it away.
Reassemble the filters in the reverse order of the
disassembly, replace the filter insert, and rotate
clockwise to the close arrow.
To remove the upper spray arm, hold the nut in the
center still and rotate the spray arm counterclockwise
to remove it.
Open
Coarse filter
Main filter
Fine filter
WARNING!
Do not over tighten the filters. Put the filters back
in sequence securely, otherwise coarse debris
could get into the system and cause a blockage.
NEVER use the dishwasher without filters in
place. Improper replacement of the filter may
reduce the performance level of the appliance
and damage dishes and utensils.
Spray arms
It is necessary to clean the spray arms regularly for
hard water chemicals will clog the spray arm jets
and bearings.
To clean the spray arms, follow the instructions:
10
ENG
Caring For The Dishwasher
Frost precaution
Please take frost protection measures on the dishwasher in winter. After every washing cycles, please operate as
follows:
1. Cut off the electrical power to the dishwasher at the power source.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
After every wash
After every wash, turn off the water supply to the appliance and leave the door slightly open so that moisture and
odours are not trapped inside.
Remove the plug
Before cleaning or performing maintenance, always remove the plug from the socket.
No solvents or abrasive cleaning
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Only
use a cloth with warm soapy water.
To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little vinegar, or a
cleaning product made specifically for dishwashers.
When not in use for a longtime
It is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of the appliance slightly open. This will help the door seals to
last longer and prevent odours from forming within the appliance.
Moving the appliance
If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be positioned
on its back.
Seals
One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic
cleaning with a damp sponge will prevent this from occurring.
To remove the lower spray arm, pull out the spray arm
upward.
Wash the arms in soapy and warm water and use a
soft brush to clean the jets. Replace them after rinsing
them thoroughly.
11
ENG
INSTALLATION INSTRUCTION
About Power Connection
Safety supply hose
Ordinary supply hose
WARNING!
WARNING!
WARNING!
Electrical Shock Hazard
Disconnect electrical power before installing dishwasher.
Failure to do so could result in death or electrical shock.
For personal safety:
Do not use an extension cord or an adapter plug with this appliance.
Do not, under any circumstances, cut or remove the grounding connection from the power cord.
Electrical requirements
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power
supply. Use the required fuse 10A/13A/16A, time delay fuse or circuit breaker recommended and provide
separate circuit serving only this appliance.
Electrical connection
Ensure the voltage and frequency of the power being corresponds to those on the rating plate. Only insert the
plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the socket, rather than using a adaptors or the like as they could
cause overheating and burns.
Ensure that proper grounding exists before use.
Water Supply and Drain
Cold water connection
Connect the cold water supply hose to a threaded
3/4(inch) connector and make sure that it is fastened
tightly in place.
If the water pipes are new or have not been used for
an extended period of time, let the water run to make
sure that the water is clear. This precaution is needed
to avoid the risk of the water inlet to be blocked and
damage the appliance.
About the safety supply hose
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the
flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the
outer corrugated hose is full of water.
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink
has one, it is recommended that the hose be disconnected and the hole plugged.
ATTENTION!
The installation of the pipes and electrical equipments should be done by professionals.
12
ENG
How to drain excess water from hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly into the sink. It will be
necessary to drain excess water from hoses into a bowl or suitable container that is held outside and lower than the
sink.
Water outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks. Ensure that the water
drain hose is not kinked or squashed.
Extension hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 meters; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon connection
The waste connection must be at a height less than 100 cm (maximum) from the bottom of the dish. The water
drain hose should be fixed.
40 mm
Back of dishwasher
Drain hose
Counter
Water Inlet
Power Cable
Drain Pipe
How to connect the safety supply hose
1. Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
2. Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
3. Turn water fully on before starting the dishwasher.
How to disconnect the safety supply hose
1. Turn off the water.
2. Unscrew the safety supply hose from the faucet.
Connection of Drain Hoses
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making sure to
avoid bending or crimping it. The height of drain pipe must be less than 1000mm. The free end of the hose must
not be immersed in water to avoid the back flow of it.
Please securely fix the drain hose in either position A or position B
13
ENG
Position The Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can be
positioned either to the right or the left sides to facilitate proper installation.
Levelling the appliance
Once the appliance is positioned for levelling, the height
of the dishwasher may be altered via adjustment of the
screwing level of the feet.
In any case,the appliance should not be inclined
more than 2°.
NOTE
Only apply to the free standing dishwasher.
Free Standing Installation
Fitting between existing cabinets
The height of the dishwasher, 845 mm, has been designed
in order to allow the machine to be fitted between existing
cabinets of the same height in modern fitted kitchens. The
feet can be adjusted so that correct height is reached.
The laminated top of the machine does not require any
particular care since it is heatproof, scratchproof and
stainproof.
Underneath existing work top
(When fitting beneath a work top)
In most modern fitted kitchens there is only one single
work top under which cabinets and electrical appliances
are fitted. In this case remove the work top of the
dishwasher by unscrewing the screws under the rear edge
of the top (a).
ATTENTION!
After removing the work top, the screws must be screwed
again under the rear edge of the top (b).
The height will then be reduced to 815 mm, as scheduled
by the International Regulations (ISO) and the dishwasher
will fit perfectly under the kitchen working top.
Built-In Installation (for the integrated model)
Step 1. Selecting the best location for the dishwasher
The installation position of dishwasher should be near the existing inlet and drain hoses and power cord.
Illustrations of cabinet dimensions and installation position of the dishwasher.
1. Less than 5 mm between the top of dishwasher and cabinet and the outer door aligned to cabinet.
14
ENG
Electrical, drain
and water supply
line entrances
Space between cabinet
bottom and floor
600 mm (for 60 cm model)
450 mm (for 45 cm model)
2. If dishwasher is in stalled at the corner of the cabinet,
there should be some space when the door is opened.
NOTE
Depending on where your electrical outlet is, you may need
to cut a hole in the opposite cabinet side.
CabinetDishwasher
Door of
dishwasher
Minimum space
of 50mm
Step 2. Aesthetic panel’s dimensions and installation
Magical paster
1. Take away the four short screws
2. Pin up the four long screws
Magical paster
NOTE
The aesthetic wooden panel could be processed according to the installation drawings.
Semi-integrated model
Magical paster A and magical paster B be disjoinedon ,magical paster A on the aesthetic wooden panel and
felted magical paster B of the outer door of dishwasher (see figure A). After positioning of the panel , fix the
panel onto the outer door by screws and bolts (See figure B).
15
ENG
Full-integrated model
Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of dishwasher (see
figure A). After positioning of the panel , fix the panel onto the outer door by screws and bolts (See figure B).
1. Take away the four short screws
2.Pin up the four long screws
Step 3. Tension adjustment of the door
1. The door springs are set at the factory to the proper
tension for the outer door. If aesthetic wooden panel are
installed, you will have to adjust the door spring tension.
Rotate the adjusting screw to drive the adjustor to strain
or relax the steel cable.
2. Door spring tension is correct when the door remains
horizontal in the fully opened position, yet rises to a close
with the slight lift of a finger
Step 4. Dishwasher installation steps
Please refer to the specified installation steps in the installation drawings.
NOTE
1. Affix the condensation strip under the work surface of cabinet. Please ensure the condensation strip is flush with
edge of work surface. (Step 2)
2. Connect the inlet hose to the cold water supply.
3. Connect the drain hose.
4. Connect the power cord.
5. Place the dishwasher into position. (Step 4)
6. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the Philips
screw in the middle of the base of dishwasher use an Philips screw. To adjust the front feet, use a flat screw
driver and turn the front feet until the dishwasher is level. (Step 5 to Step 6)
7. Install the furniture door to the outer door of the dishwasher. (Step 7 to Step 10)
8. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left and
right door springs. Failure to do this could cause damage to your dishwasher. (Step 11)
9. The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface: Put the installation hook into the slot of the side plane and secure it to the work surface
with the wood screws.
B. Marble or granite work top: Fix the side with Screw.
16
ENG
Step 5. Levelling the dishwasher
Dishwasher must be level for proper dish rack operation and wash performance.
1. Place a spirit level on door and rack track inside the tub as shown to check that the dishwasher is level.
2. Level the dishwasher by adjusting the three levelling legs individually.
3. When level the dishwasher, please pay attention not to let the dishwasher tip over.
Check level
front to back
Check level
side to side
NOTE
maximum adjustment height of the feet is 50 mm.
17
ENG
TROUBLESHOOTING TIPS
Before Calling for Service
Reviewing the charts on the following pages may save you from calling for service.
Problem Possible Causes What to Do
Dishwasher doesn’t start
Fuse blown, or the circuit break
tripped.
Replace fuse or reset circuit
breaker. Remove any other
appliances sharing the same circuit
with the dishwasher.
Power supply is not turned on.
Make sure the dishwasher is
turned on and the door is closed
securely. Make sure the power cord
is properly plugged into the wall
socket.
Water pressure is low
Check that the water supply is
connected properly and the water
is turned on.
Door of dishwasher not properly
closed.
Make sure to close the door
properly and latch it.
Water not pumped form
dishwasher
Twisted or trapped drain hose. Check the drain hose.
Filter clogged. Check coarse the filter.
Kitchen sink clogged.
Check the kitchen sink to make
sure it is draining well. If the
problem is the kitchen sink that
is not draining, you may need a
plumber rather than a serviceman
for dishwashers.
Suds in the tub
Wrong detergent.
Use only the special dishwasher
detergent to avoid suds. If this
occurs, open the dishwasher and
let suds evaporate. Add 1 gallon
of cold water to the bottom of the
dishwasher.
Close the dishwasher door, then
select any cycle. Initially, the
dishwasher will drain out the water.
Open the door after draining
stage is complete and check if the
suds have disappeared. Repeat if
necessary.
Spilled rinse-aid.
Always wipe up rinse-aid spills
immediately.
Stained tub interior
Detergent with colorant may have
been used.
Make sure that the detergent has
no colorant.
White film on inside surface Hard water minerals.
To clean the interior, use a damp
sponge with dishwasher detergent
and wear rubber gloves. Never use
any other cleaner than dishwasher
detergent otherwise, it may cause
foaming or suds.
18
ENG
Problem Possible Causes What to Do
There are rust stains on cutlery
The affected items are not
corrosion resistant.
Avoid washing items that are
not corrosion resistant in the
dishwasher.
A program was not run after
dishwasher salt was added. Traces
of salt have gotten
into the wash cycle.
Always run a wash program
without any crockery after adding
salt. Do not select the Turbo
function (if present), after adding
dishwasher salt.
The lid of the softer is loose. Check the softener lid is secure.
Knocking noise in the dishwasher
A spray arm is knocking against an
item in a basket
Interrupt the program and
rearrange the items which are
obstructing the spray arm.
Rattling noise in the dishwasher
Items of crockery are loose in the
dishwasher.
Interrupt the program and
rearrange the items of crockery.
Knocking noise in the water pipes
This may be caused by on-site
installation or the cross-section
of the piping.
This has no influence on the
dishwasher function. If in doubt,
contact a qualified plumber.
The dishes are not clean
The dishes were not loaded
correctly.
See PART II “Preparing And
Loading Dishes”.
The program was not powerful
enough.
Select a more intensive program.
Not enough detergent was
dispensed
Use more detergent, or change
your detergent.
Items are blocking the movement
of the spray arms.
Rearrange the items so that the
spray can rotate freely.
The filter combination is not clean
or is not correctly fitted in the base
of wash cabinet.
This may cause the spray arm jets
to get blocked.
Clean and fit the filter correctly.
Clean the spray arm jets.
Cloudiness on glassware.
Combination of soft water and too
much detergent.
Use less detergent if you have soft
water and select a shorter cycle
to wash the glassware and to get
them clean.
White spots appear on dishes and
glasses.
Hard water area
can cause limescale deposits.
Add more detergent.
Black or grey marks on dishes
Aluminum utensils have rubbed
against dishes
Use a mild abrasive cleaner to
eliminate those marks.
Detergent left in dispenser Dishes block detergent dispenser Re-loading the dishes properly.
The dishes aren't drying
Improper loading
Load the dishwasher as suggested
in the directions.
Dishes are removed too soon
Do not empty your dishwasher
immediately after washing. Open
the door slightly so that the steam
can come out. Take out the dishes
until the inside temperature is safe
to touch. Unload the lower basket
first to prevent the dropping water
from the upper basket.
19
ENG
Problem Possible Causes What to Do
The dishes aren't drying
Wrong program has been
selected.
With a short program, the washing
temperature is lower, decreasing
cleaning performance. Choose a
program with a long washing time.
Use of cutlery with a low-quality
coating.
Water drainage is more difficult
with these items. Cutlery or dishes
of this type are not suitable for
washing in the dishwasher.
LOADING THE BASKETS ACCORDING TO
EN50242
1. Upper basket: 2. Lower basket:
Number Item
1 Cups
2 Saucers
3 Glasses
4 Small serving bowl
5 Medium serving bowl
6 Large serving bowl
Number Item
7 Dessert dishes
8 Dinner plates
9 Soup plates
10 Oval platter
11 Cutlery basker
20
ENG
Information for comparability tests in
accordance with EN 50242
Capacity: 9 place settings
Position of the upper basket: lower position
Program: ECO
Rinse aid setting: MAX
Softener setting: H3
Number Item
1 Soup spoons
2 Forks
3 Knives
4 Teaspoons
5 Dessert spoons
6 Serving spoons
7 Serving forks
8 Gravy ladles
3. Cutlery rack:
4. Cutlery basket
NOTE
Please place the light flat wares on the shelf. The total weight is less than 1.5kg.
IN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208

Tesla WDI461M Manual de utilizare

Categorie
Mașini de spălat vase
Tip
Manual de utilizare