Milwaukee M18 CAG115X Original Instructions Manual

Original instructions

Originalbetriebsanleitung

Notice originale

Istruzioni originali

Manual original

Oorspronkelijke

gebruiksaanwijzing

Original brugsanvisning

Original bruksanvisning

Bruksanvisning i original

Alkuperäiset ohjeet

Πρωτότυπο οδηγιών χρήσης

Orijinal işletme talimatı

Původním návodem k

používání

Pôvodný návod na použitie

Instrukcją oryginalną

Eredeti használati utasítás

Izvirna navodila

Originalne pogonske upute

Instrukcijâm oriěinâlvalodâ

Originali instrukcija

Algupärane kasutusjuhend

Оригинальное руководство

по эксплуатации

Оригинално ръководство за

експлоатация

Instrucţiuni de folosire

originale

Оригинален прирачник за

работа

原始的指南

M18 CAG115X

M18 CAG125X

M18 CAG115XPD

M18 CAG125XPD

Technical Data,Safety Instructions, Specied Conditions of Use,

EC-Declaration of Conformity, Batteries, Maintenance, Symbols

Please read and save

these instructions!

Technische Daten, Sicherheitshinweise, Bestimmungsgemäße Verwendung,

CE-Konformitätserklärung, Akkus, Wartung, Symbole

Bitte lesen und

aufbewahren!

Caractéristiques techniques, Instructions de sécurité, Utilisation conforme aux

prescriptions, Déclaration CE de Conformité, Accus, Entretien, Symboles

A lire et à conserver

soigneusement

Dati tecnici,Norme di sicurezza,Utilizzo conforme, Dicharazione di Conformità CE,

Batterie, Manutenzione, Simboli

Si prega di leggere e

conservare le istruzioni!

Datos técnicos, Instrucciones de seguridad, Aplicación de acuerdo a la nalidad,

Declaracion de Conformidad CE, Bateria, Mantenimiento, Símbolos

Lea y conserve estas

instrucciones por favor!

Características técnicas, Instruções de segurança, Utilização autorizada,

Declaração de Conformidade CE, Acumulador, Manutenção, Symbole

Por favor leia e conserve

em seu poder!

Technische gegevens, Veiligheidsadviezen, Voorgeschreven gebruik van het

systeem, EC-Konformiteitsverklaring, Akku, Onderhoud, Symbolen

Lees en let goed op

deze adviezen!

Tekniske data, Sikkerhedshenvisninger, Tiltænkt formål,

CE-Konformitetserklæring, Batteri, Vedligeholdelse, Symboler

Vær venlig at læse

og Opbevare!

Tekniske data, Spesielle sikkerhetshenvisninger, Formålsmessig bruk,

CE-Samsvarserklæring, Batterier, Vedlikehold, Symboler

Vennligst les og oppbevar!

Tekniska data, Säkerhetsutrustning, Använd maskinen Enligt anvisningarna,

CEFörsäkran, Batterier, Skötsel, Symboler

Läs igenom och spara!

Tekniset arvot, Turvallisuusohjeet, Tarkoituksenmukainen käyttö,

Todistus CE-standardinmukaisuudesta, Akku, Huolto, Symbolit

Lue ja säilytö!

Τεχνικά στοιχεία, Ειδικές υποδείξεις ασφάλειας, Χρήση σύμφωνα με το σκοπό

προορισμού, Δήλωση πιστότητας ΕΚ, Μπαταρίες, Χαρακτηριστικά, Συντήρηση, Σύμβολα.

Teknik veriler, Güvenliğiniz için talimatlar, Kullanim, CE uygunluk beyanice,

Akü, Bakim, Semboller

Lütfen okuyun ve saklayın

Technická data, Speciální bezpečnostní upozornění, Oblast využití,

Ce-prohlášení o shodě, Akumulátory, Údržba, Symboly

Po přečtení uschovejte

Technické údaje, Špeciálne bezpčènostné pokyny, Použitie podl’a predpisov,

CE-Vyhlásenie konformity, Siet’ová prípojka, Údrzba, Symboly

Prosím prečítať a uschovať!

Dane techniczne, Specjalne zalecenia dotyczące bezpiecze´nstwa, Użytkowanie zgodne z

przeznaczeniem, Świadectwo zgodności ce, Podłączenie do sieci, Gwarancja, Symbole

Należy uważnie przeczytać i

zachować do wglądu!

Műszaki adatok, Különleges biztonsági tudnivalók, Rendeltetésszerű használat,

Ce-azonossági nyilatkozat, Hálózati csatlakoztatás, Karbantartás, Szimbólumok

Olvassa el és őrizze meg

Tehnični podatki, Specialni varnostni napotki, Uporaba v skladu z namembnostjo,

Ce-izjava o konformnosti, Omrežni priključek, Vzdrževanje, Simboli

Prosimo preberite

in shranite!

Tehnički podaci, Specijalne sigurnosne upute, Propisna upotreba,

CE-Izjava konformnosti, Priključak na mrežu, Održavanje, Simboli

Molimo pročitati i sačuvati

Tehniskie dati, Speciālie drošības noteikumi, Noteikumiem atbilstošs izmantojums,

Atbilstība CE normām, Tīkla pieslēgums, Apkope, Simboli

Pielikums lietošanas pamācībai

Techniniai duomenys, Ypatingos saugumo nuorodos, Naudojimas pagal paskirti,

CE Atitikties pareiškimas, Elektros tinklo jungtis, Techninis aptarnavimas, Simboliai

Prašome perskaityti

ir neišmesti!

Tehnilised andmed, Spetsiaalsed turvajuhised, Kasutamine vastavalt otstarbele,

EÜ Vastavusavaldus, Võrku ühendamine, Hooldus, Sümbolid

Palun lugege läbi ja hoidke alal!

Òåõíè÷åñêèå äàííûå, Ðåêîìåíäàöèè ïî òåõíèêå áåçîïàñíîñòè,

Èñïîëüçî- âàíèå, Ïîäêëþ÷åíèå ê ýëåêòðîñåòè, Îáñëóæèâàíèå, Ñèìâîëû

Пожалуйста прочтите и

сохраните эту инструкцию.

Òåõíè÷åñêè äàííè, Ñïåöèàëíè óêàçàíèÿ çà áåçîïàñíîñò, Èçïîëçâàíå ïî ïðåäíàçíà÷åíèå,

ÑÅ-Äåêëàðàöèÿ çà ñúîòâåòñòâèå, Ñâúðçâàíå êúì ìðåæàòà, Ïîääðúæêà, Ñèìâîëè

Моля прочетете и запазете!

Date tehnice, Instrucţiuni de securitate, Condiţii de utilizare specifcate,

Declaraţie de conformitate, Acumulatori, Intreţinere, Simboluri

Va rugăm citiţi şi păstraţi

aceste instrucţiuni

Òåõíè÷êè Ïîäàòîöè, Óïàòñòâî Çà Óïîòðåáà, Ñïåöèôèöèðàíè Óñëîâè Íà

Óïîòðåáà, Åó-äåêëàðàöè¼à Çà Ñîîáðàçíîñò, БАТЕРИИ, Îäðæóâàњå, Ñèìáîëè

Ве мoлиме прочитаjте го и

чувајте го ова упатство!

技术参数, 特别安全说明书, 详细使用说明, 欧盟符合性声明, 电源连接,

维护保养, 符号

请详细阅读并妥善保存！

English 15

Deutsch 19

Français 23

Italiano 28

Español 33

Português 38

Nederlands 43

Dansk 47

Norsk 51

Svenska 55

Suomi 59

Ελληνικά 63

Türkçe 68

Česky 72

Slovensky 76

Polski 80

Magyar 85

Slovensko 89

Hrvatski 93

Latviski 97

Lietuviškai 101

Eesti 105

Pусский 109

български 114

Romănia 119

Македонски 123

中文 128

TIP

III

V

IX

II

VIII

VIIV

VII

I

Accessory

Zubehör

Accessoires

Accessorio

Accessorio Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite

Εξαρτήματα

Aksesuar

Příslušenství

Príslušenstv

Wyposażenie

Azokat a tartozékokat

Oprema

Piederumi

Priedas

Tarvikud

Äîïîëíèòåëü

Аксесоари

Accesoriu

ополнителна

опрема

配件

2

I

1.

2.

3

I

78-100 %

33-54 %

55-77 %

10-32 %

<10 %

4

I

A

B

II

5

I

III

1.

2.

3.

1

2

6

IV

0°

30°

60°

30

°

60

°

30

°

60

°

0

°

7

I

V

2.

1.

3.

< 6 mm

> 6 mm

4.

8

V

3.

2.1.

9

VI

Stop

Start Stop

Start

M18 CAG115X / M18 CAG125X

M18 CAG115XPD / M18 CAG125XPD

1

2

10

VI

Startup protection:

The tool will not restart after an interruption of the mains supply without releasing

and reactuating the switch.

Wiederanlaufschutz:

Eingeschaltete Maschine läuft nach Spannungsausfall nicht wieder an.

Um weiter zu arbeiten Maschine aus- und wieder einschalten.

Dispositif de protection contre un redemarrage

Après une coupure de tension, la machine enclenchée ne redémarre pas.

Pour continuer à travailler, il convient d'éteindre la machine et de l'enclencher à

nouveau.

Protezione contro il riavvio

La macchina accesa non riparte in seguito alla caduta della tensione. Per poter

continuare a lavorare bisogna prima spegnere e poi riaccendere la macchina.

Protección contra el rearranque

La máquina conectada no se vuelve a poner en marcha después de un fallo de

corriente. Para continuar el trabajo, desconectar y volver a conectar la máquina.

Protecção de reinício

Quando está ligada, após uma falha de energia a máquina não retoma o seu

funcionamento. Para prosseguir o trabalho, desligar a máquina e voltar a ligá-la.

Herstartbeveiliging

Na spanningsuitval schakelt de machine niet automatisch weer in.

Schakel de machine uit en weer in om door te kunnen werken.

Genstartsbeskyttelse

I tilfælde af spændingsudfald, mens maskinen kører, går den ikke i gang igen, når

spændingen kommer tilbage. For at genoptage arbejdet skal maskinen slukkes og

tændes igen.

Automatisk gjenstartsbeskyttelse

En påslått maskin begynner ikke automatisk å gå igjen etter strømbrudd.

For å kunne fortsette å arbeide må maskinen skues av og så på igjen.

Återstartsskydd

En påslagen maskin startar inte själv efter ett strömavbrott.

Stäng först av och slå sedan på maskinen igen för att fortsätta att arbeta.

Uudelleenkäynnistyssuoja

Päällekytketty kone ei käynnisty sähkökatkon jälkeen uudestaan.

Työn jatkamiseksi tulee kone sammuttaa ja käynnistää uudelleen.

Προστασια επανεκκινηση

Η ενεργοποιημένη μηχανή δεν ξεκινά πάλι από μόνη της μετά από μια πτώση

ρεύματος. Για να συνεχίσετε την εργασία, απενεργοποιείτε και ενεργοποιείτε πάλι

τη μηχανή.

Tekrar çalitirmada koruma

Çalıştırılan makine voltaj kaybından sonra yeniden çalışmaz. Makineyi tekrar

çalıştırmak için kapatın ve tekrar açın.

Ochrana proti opětovnému náběhu

Zapnutá rozbrušovačka se v případě výpadku proudu po jeho opětovném zapnutí

sama nerozběhne. K pokračování práce se rozbrušovačka musí vypnout a opět

zapnout.

Ochrana proti opätovnému nábehu

Zapnutá rozbrusovačka sa v prípade výpadku prúdu po jeho opätovnom zapnutí

sama nerozbehne. K pokračovaniu práce sa rozbrusovačka musí vypnúť a opäť

zapnúť.

Zabezpieczenie przed ponownym uruchomieniem

Włączone urządzenie nie uruchamia się z powrotem po ustąpienia zaniku napięcia.

Aby móc kontynuować pracę, urządzenie należy wyłączyć, a potem z powrotem

włączyć.

Újraindulás elleni védelem

A bekapcsolt gép feszültségkimaradás után ismét elindul. A munka folytatásához a

gépet ki és újra be kell kapcsolni.

Zaščita pred ponovnim zagonom

Vklopljen stroj se po izpadu napetosti ponovno ne zažene. Za nadaljevanje dela stroj

izklopite in ponovno vklopite.

Zaštita protiv ponovnog pokretanja

Uključeni stroj poslilje nestanka napona više ne starta. Da bi se dalje radilo, stroj

isključiti i ponovno uključiti.

Aizsardzība pret atkārtotu palaišanu

Pārtrūkstot strāvas padevei, ieslēgtā ierīce no jauna neieslēdzas.

Darba turpināšanai ierīci izslēgt un ieslēgt no jauna.

Apsauga nuo pakartotinio įsijungimo

Jei darbo metu dingsta įtampa, ją sutvarkius, mašina neįsijungia automatiškai. Norint

vėl dirbti su mašina, reikia ją išjungti ir vėl įjungti.

Taaskäivituskaitse

Sisselülitatud masin ei käivitu enam uuesti pärast voolukatkestust.

Töö jätkamiseks lülitage masin välja ja seejärel taas sisse.

   

При исчезновении напряжения устройство не работает. Для продолжения

работы устройство выключите и снова включите.

   

След спиране на електрозахранването включената машина не започва да

работи отново. За да продължите работа изключете и отново включете

машината.

Protecie contra repornirii

Maşina conectată nu reporneşte după o întrerupere de curent.

Pentru a putea lucra în continuare, maşina trebuie oprită şi apoi repornită.

   

Вклучената машина во случај на снемување струја не се вклучува повторно.

а да продолжите со работа исклучете ја машината и вклучете ја повторно.

再起动保护

电压消失后开动的机器不自动起动。为继续工作要将机器关

闭并再开动。

11

TIP

VII

TIP

< 30°

12

VIII

1. 2.

1.

2.

13

I

VIII

1. 2.

3.

14

VIII

3.

2.1.

D

Deutsch

15

GB

English

b) Operations such as polishing are not recommended

to be performed with this power tool.Operations for which

the power tool was not designed may create a hazard and cause

personal injury.

c) Do not use accessories which are not specically

designed and recommended by the tool manufacturer. Just

because the accessory can be attached to your power tool, it does

not assure safe operation.

d) The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Accesso-

ries running faster than their rated speed can break and y apart.

WARNING!

Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire

Brushing or Abrasive Cutting-O Operations:

a) This power tool is intended to function as a grinder,

sander, wire brush or cut-o tool. Read all safety warnings,

instructions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

TECHNICAL DATA

Angle Grinder

M18 CAG115X

M18 CAG125X

M18 CAG115XPD

M18 CAG125XPD

Production code 4439 26 01...

... 000001-999999

4439 41 01...

... 000001-999999

4475 91 01...

... 000001-999999

4476 06 01...

... 000001-999999

Volts 18 V 18 V 18 V 18 V

Rated speed 8500 min

-1

8500 min

-1

8500 min

-1

8500 min

-1

D= Grinding disk diameter max.

d= Grinding disk hole diameter

115 mm

22,2 mm

125 mm

22,2 mm

115 mm

22,2 mm

125 mm

22,2 mm

b= Cutting disk thickness min. / max.

1 / 3 mm 1 / 3 mm 1 / 3 mm 1 / 3 mm

b= Grinding disk thickness max. 6 mm 6 mm 6 mm 6 mm

D= Grinding surface diameter max. 115 mm 125 mm 115 mm 125 mm

D= Wiring brush diameter max. 75 mm 75 mm 75 mm 75 mm

Thread of work spindle M 14 M 14 M 14 M 14

Weight without battery 1,8 kg 1,8 kg 1,8 kg 1,8 kg

Weight according EPTA-Procedure 01/2003 (Li-lon 4,0 Ah) 2,5 kg 2,5 kg 2,5 kg 2,5 kg

Noise/Vibration Information

Measured values determined according to EN 60 745. Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A))

Sound power level (Uncertainty K=3dB(A))

Wear ear protectors!

83,7 dB(A)

94,7 dB(A)

83,2 dB(A)

94,2 dB(A)

83,7 dB(A)

94,7 dB(A)

83,2 dB(A)

94,2 dB(A)

Vibration total values (triaxial vector sum) determined according to EN 60745

surface grinding: Vibration emission value a

h,SG

Uncertainty K=

3,3 m/s

2

1,5 m/s

2

3,4 m/s

2

1,5 m/s

2

3,3 m/s

2

1,5 m/s

2

3,4 m/s

2

1,5 m/s

2

Disk sanding: Vibration emission value a

h,DS

Uncertainty K=

1,5 m/s

2

1,5 m/s

2

1,4 m/s

2

1,5 m/s

2

1,5 m/s

2

1,5 m/s

2

1,4 m/s

2

1,5 m/s

2

For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745

and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for dierent applications,

with dierent accessories or poorly maintained, the vibration emission may dier. This may signicantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is

running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories,

keep the hands warm, organisation of work patterns.

D

Deutsch

16

GB

English

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately guarded

or controlled.

f) Treaded mounting of accessories must match the grinder

spindle thread. For accessories mounted by anges, the ar-

bour hole of the accessory must t the locating diameter of

the ange. Accessories that do not match the mounting hardware

of the power tool will run out of balance, vibrate excessively and

may cause loss of control.

g) Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart during this

test time.

h) Wear personal protective equipment. Depending on ap-

plication, use face shield, safety goggles or safety glasses. As

appropriate, wear dust mask, hearing protectors, gloves and

shop apron capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of stopping ying

debris generated by various operations. The dust mask or respirator

must be capable of ltrating particles generated by your operation.

Prolonged exposure to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work area. An-

yone entering the work area must wear personal protective

equipment. Fragments of workpiece or of a broken accessory may

y away and cause injury beyond immediate area of operation.

j) Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting a „live“

wire may make exposed metal parts of the power tool „live“ and

could give the operator an electric shock.

k) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

l) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your

clothing, pulling the accessory into your body.

m) Regularly clean the power tool’s air vents. The motor’s fan

will draw the dust inside the housing and excessive accumulation of

powdered metal may cause electrical hazards.

n) Do not operate the power tool near ammable materials.

Sparks could ignite these materials.

o) Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or snag-

ging causes rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also break

under these conditions.

Kickback is the result of power tool misuse and/or incorrect opera-

ting procedures or conditions and can be avoided by taking proper

precautions as given below.

a) Maintain a rm grip on the power tool and position your

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper precautions

are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool in di

-

rection opposite to the wheel’s movement at the point of snagging.

d)

Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specic for Grinding and Abrasive Cutting-

O Operations:

a) Use only wheel types that are recommended for your

power tool and the specic guard designed for the selected

wheel. Wheels for which the power tool was not designed cannot

be adequately guarded and are unsafe.

b) The grinding surface of the centre depressed wheels must

be mounted below the plane of the guard lip. An improperly

mounted wheel that projects through the plane of the guard lip

cannot be adequately protected.

c) The guard must be securely attached to the power tool

and positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. The guard helps

to protect the operator from broken wheel fragments, accidental

contact with wheel and sparks that could ignite clothing.

d) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-o wheel. Ab

-

rasive cut-o wheels are intended for peripheral grinding, side forces

ap

plied to these wheels may cause them to shatter.

e) Always use undamaged wheel anges that are of correct

size and shape for your selected wheel. Proper wheel anges

support the wheel thus reducing the possibility of wheel breakage.

Flanges for cut-o wheels may be dierent from grinding wheel

anges.

f) Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the higher

speed of a smaller tool and may burst.

Additional Safety Warnings Specic for Abrasive Cutting-O

Operations:

a) Do not “jam” the cut-o wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut. Overstressing

the wheel increases the loading and susceptibility to twisting or

binding of the wheel in the cut and the possibility of kickback or wheel

breakage.

D

Deutsch

17

GB

English

b) Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation, is moving

away from your body, the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

reason, switch o the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never

attempt to remove the cut-o wheel from the cut while the

wheel is in motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the power tool is restarted in

the workpiece.

e) Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend to sag

under their own weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on both sides

of the wheel.

f) Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that can cause kickback.0

Safety Warnings Specic for Sanding Operations:

a) Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when selecting

sanding paper. Larger sanding paper extending beyond the

sanding pad presents a laceration hazard and may cause snagging,

tearing of the disc or kickback.

Safety Warnings Specic for Wire Brushing Operations:

a) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the wires

by applying excessive load to the brush. The wire bristles can

easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing,

do not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in diameter due

to work load and centrifugal forces.

Additional Safety and Working Instructions:

When grinding metal, ying sparks are produced. Take care that

no persons are endangered. Because of the danger of re, no

combustible materials should be located in the vicinity (spark ight

zone). Do not use dust extraction.

Avoid ying sparks and sanding dust hit your body.

Never reach into the danger area of the machine when it is running.

Immediately switch o the machine in case of considerable vibra-

tions or if other malfunctions occur. Check the machine in order to

nd out the cause.

Under extreme conditions (e.g. smooth-grinding metals with

the arbour and vulcanized bre grinding disk), signicant

contamination can build up on the inside of the angle grinder. For

safety reasons, in such conditions a ground fault interrupter must

be connected in series. If the ground fault interrupter trips the

machine must be sent for service.

Chips and splinters must not be removed while the machine is

running.

BATTERIES

New battery packs reach full loading capacity after 4 - 5 chargings

and dischargings. Battery packs which have not been used for some

time should be recharged before use.

Temperatures in excess of 50°C (122°F) reduce the performance of

the battery pack. Avoid extended exposure to heat or sunshine (risk

of overheating).

The contacts of chargers and battery packs must be kept clean.

For an optimum life-time, the battery packs have to be fully

charged, after use.

To obtain the longest possible battery life remove the battery pack

from the charger once it is fully charged.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C and

away from moisture

Store the battery packs in a 30% - 50% charged condition

Every six months of storage, charge the pack as normal.

SPECIFIED CONDITIONS OF USE

The angle grinder is intended for grinding and cutting metal, stone

and ceramicmaterials as well as sanding and wire brushing.

Use the cutting guard from the accessories range for cutting

application.

Please refer to the instructions supplied by the accessory manu-

facturer.

The machine is suitable only for working without water.

WORKING INSTRUCTIONS

For accessories intended to be tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to accept the

spindle length.

Always use and store the cutting and grinding disks according to

the manufacturer‘s instructions.

Always use the correct guard for cutting and grinding.

The grinding surface of the centre depressed disks must be moun-

ted min. 2 mm below the plane of the guard lip.

The adjusting nut must be tightened before starting to work with

the machine.

Always use the auxiliary handle.

The workpiece must be xed if it is not heavy enough to be steady.

Never move lead the workpiece towards the rotating disk by hand.

ELECTRONICS

The built-in electronic will keep a constant speed even under

increased load.

In case of overload, the rotational speed is being reduced until

machine stops.

The machine has an overload and anti-kickback safety function and

stops if it is overloaded.

Please note that the machine will automatically accelerate back to

its original operating speed if the load is removed from it.

After it has reached its operating speed the machine is ready for

use again.

D

Deutsch

18

GB

English

RESTART CUTOUT

A zero-voltage switch prevents the machine from restarting after a

power cut (Battery change).

When resuming work, switch the machine o and then switch it

back on again.

SMOOTH START

Electronic smooth start for save use prevents jerky run-up of the

machine.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.

If the supply cord of this power tool is damaged, it must be

replaced by a specially prepared cord available through the service

organization.

Use only Milwaukee accessories and Milwaukee spare parts. Should

components need to be replaced which have not been described, please

contact one of our Milwaukee service agents (see our list of guarantee/

service addresses).

If needed, an exploded view of the tool can be ordered. Please state

the machine type printed as well as the six-digit No. on the label

and order the drawing at your local service agents or directly at:

Techtronic Industries GmbH, Max-Eyth-Straße10, 71364Winnen-

den, Germany.

ECDECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described

under “Technical Data” fullls all the relevant provisions of the direc-

tives 2011/65/EU (RoHs), 2004/108/EC, 2006/42/EC and the following

harmonized standards have been used:

EN 60745-1:2009 + A11:2010

EN 60745-2-3:2011 + A2:2013

EN 55014-1:2006 + A1:2009 + A2:2011

EN 55014-2:1997 + A1:2001 + A2:2008

Winnenden, 2014-04-24

Alexander Krug / Managing Director

Authorized to compile the technical le

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

SYMBOLS

CAUTION! WARNING! DANGER!

Please read the instructions carefully before starting the

machine.

Always wear goggles when using the machine.

Wear gloves!

Remove the battery pack before starting any work on

the machine.

Do not use force.

Only for cutting work.

Only for grinding.

Accessory - Not included in standard equipment, availa-

ble as an accessory.

Do not dispose of electric tools together with household

waste material. Electric tools and electronic equipment

that have reached the end of their life must be collected

separately and returned to an environmentally compa-

tible recycling facility. Check with your local authority or

retailer for recycling advice and collection point.

Class II tool Tool in which protection against electric

shock does not rely on basic insulation only, but in which

additional safety precautions, such as double insulation

or reinforced insulation, are provided. There being

no provision for protective earthing or reliance upon

installation conditions.

European Conformity Mark

Pagina se încarcă ...

Milwaukee M18 CAG115X Original Instructions Manual

Acest manual este potrivit și pentru

Milwaukee M18 CAG115X Original Instructions Manual

în alte limbi

Lucrări conexe

Alte documente