Ubiquiti AM-V2G-TI Manualul utilizatorului

Marca: Ubiquiti

Model: AM-V2G-TI

Categorie: Convertoare media de rețea

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

8-Port Router

with 2 Combination

SFP/RJ45 Ports

Model: ERPro-8

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter

™

PRO, which is part of the EdgeMAX® platform.

Formore information, visit www.ubnt.com/edgemax

This Quick Start Guide is designed to guide you through

installation and show how to access the EdgeOS

™

Configuration Interface. This guide also includes the warranty

terms and is for use with the EdgeRouter PRO, modelERPro-8.

Package Contents

EdgeRouter PRO

8-Port Router

with 2 Combination

SFP/RJ45 Ports

Model: ERPro-8

Power Cord Mounting Screws

(#10-32 x 5/8", Qty. 4)

Cage Nuts

(#10-32 x 5/8", Qty. 4)

Quick Start

Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Hardware Overview

Front Panel Ports

Console

RJ45 (eth0-eth7)

SFP (eth6-eth7)

USB

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port, then

you will also need a DB9 adapter.) Then

configure the following settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

USB Reserved for future use.

RJ45

(eth0-eth7)

RJ45 ports support 10/100/1000 Ethernet

connections. RJ45 port eth6 or eth7 is

active only if the corresponding SFP port

is empty.

SFP

(eth6-eth7)

SFP ports are hot-swappable and support

100 Mbps or Gigabit fiber SFP modules. If

an SFP module is plugged in, then the SFP

port is active, and the corresponding RJ45

port is deactivated.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter PRO to factory defaults:

• Runtime reset (recommended) The

EdgeRouter PRO should be running

after bootup is complete. Press and hold

the Reset button for about 10seconds

until the right LED on RJ45 port eth7

starts flashing and then becomes solidly

lit. After a few seconds, the LED will

turn off, and the EdgeRouter PRO will

automatically reboot.

• Power-on reset Disconnect the Power

Cord from the EdgeRouter PRO. Press and

hold the Reset button while connecting

the Power Cord to the EdgeRouter PRO.

Keep holding the button until the right

LED on RJ45 port eth7 starts flashing and

then stops flashing after a few seconds.

Front Panel LEDs

The LEDs on the left side of the RJ45 ports are not used at this

time. Below is a description of the other LEDs:

PowerSFP: Speed/Link/ActRJ45: Speed/Link/Act

LED State Status

RJ45 (eth0-7)

Speed/

Link/Act

Off No Link

Amber

Link Established at

10/100Mbps

Amber Flashing

Link Activity at

10/100Mbps

Green

Link Established at

1000Mbps

Green Flashing

Link Activity at

1000Mbps

SFP (eth6-7)

Speed/

Link/Act

Off No Link

Amber

Link Established at

10/100Mbps

Amber Flashing

Link Activity at

10/100Mbps

Green

Link Established at

1000Mbps

Green Flashing

Link Activity at

1000Mbps

Power

White

EdgeRouter PRO is

poweredon.

Back Panel

Mounting Holes

Power

Ventilation Holes

Mounting Holes

Fans

Note: There are additional ventilation holes on the sides

of the EdgeRouter PRO.

Installation Requirements

• Phillips screwdriver

• Standard-sized, 19" wide rack with a minimum of 1U height

available

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your outdoor networks

from the most brutal environments and devastating ESD

attacks with industrial-grade shielded Ethernet cable,

TOUGHCable

™

, from Ubiquiti Networks. For more details,

visit: www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the EdgeRouter PRO itself should be housed inside a

protective enclosure.

Hardware Installation

1. Connect the Power Cord to the Power port of the

EdgeRouter PRO.

2. Attach the EdgeRouter PRO to the rack using the four

Mounting Screws. (If the rack has square slots, then use the

Cage Nuts with the Mounting Screws.)

Note: Keep 20 mm of clearance next to the

ventilation holes for adequate airflow.

3. Connect the other end of the Power Cord to a power outlet.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a fiber SFP module into the SFP port.

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

SN: 13 0826 179

EF -10 00M -2 0KM -15

Note: The corresponding RJ45 port will be deactivated.

3. Connect a fiber optic cable to the fiber SFP module. Then

connect the other end of the cable to another fiber device.

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

Accessing the EdgeOS Configuration Interface

1. Connect an Ethernet cable from the Ethernet port of your

computer to the port labeled eth0 on the EdgeRouter PRO.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type https://192.168.1.1 in the

address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing

you to customize your settings as needed. You can click the

Wizards tab to access the Setup Wizard.

For more information, refer to the EdgeOS User Guide, which is

available at documentation.ubnt.com/edgemax

Specifications

EdgeRouter PRO

Dimensions 484 x 164 x 44 mm (19.06 x 6.46 x 1.73")

Weight 2.3 kg (5.07 lb)

Max. Power Consumption 40 W

Power Method 110 - 240VAC

Power Supply Internal AC/DC Power Adapter,

60 W (24V, 2.5A)

Button Reset

LED Power

Processor Dual-Core 1 GHz, MIPS64

with Hardware Acceleration

for Packet Processing

System Memory 2 GB DDR3 RAM

Code Storage 4 GB

Certications CE, FCC, IC

Rackmount Yes

ESD/EMP Protection Air: ±24 kV, Contact:± 24 kV

Operating Temperature -10 to 45° C (14 to 113° F)

Operating Humidity 10 - 90% Noncondensing

LEDs Per Port

Serial Console Port N/A

Data Ports Speed/Link/Activity

Networking Interfaces

Serial Console Port (1) RJ45 Serial Port

Data Ports (6) 10/100/1000 RJ45 Ports

(2) 10/100/1000 RJ45/SFP Combination Ports

*640-00094-04*

640-00094-04

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian CAN ICES-3(B).

Cet appareil numérique de la classe A est conforme à la norme NMB-3(B)

Canada.

Australia and New Zealand

Warning: This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Español

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este

símbolo en el propio aparato y/o en su embalaje no deben eliminarse

junto con otros residuos urbanos no seleccionados. El símbolo indica

que el producto en cuestión debe separarse de los residuos domésticos

convencionales con vistas a su eliminación. Es responsabilidad suya

desechar este y cualesquiera otros aparatos eléctricos y electrónicos a

través de los puntos de recogida que ponen a su disposición el gobierno y

las autoridades locales. Al desechar y reciclar correctamente estos aparatos

estará contribuyendo a evitar posibles consecuencias negativas para el

medio ambiente y la salud de las personas. Si desea obtener información

más detallada sobre la eliminación segura de su aparato usado, consulte a

las autoridades locales, al servicio de recogida y eliminación de residuos de

su zona o pregunte en la tienda donde adquirió el producto.

Français

La directive européenne 2002/96/CE exige que l’équipement sur lequel

est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté

avec les autres ordures ménagères. Ce symbole indique que le produit

doit être éliminé dans un circuit distinct de celui pour les déchets des

ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout

autre matériel électrique ou électronique par les moyens de collecte

indiqués par le gouvernement et les pouvoirs publics des collectivités

territoriales. L’élimination et le recyclage en bonne et due forme ont pour

but de lutter contre l’impact néfaste potentiel de ce type de produits

sur l’environnement et la santé publique. Pour plus d’informations sur le

mode d’élimination de votre ancien équipement, veuillez prendre contact

avec les pouvoirs publics locaux, le service de traitement des déchets, ou

l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2002/96/EC richiede che le apparecchiature

contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non

siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica

che questo prodotto non deve essere smaltito insieme ai normali rifiuti

domestici. È responsabilità del proprietario smaltire sia questi prodotti sia

le altre apparecchiature elettriche ed elettroniche mediante le specifiche

strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il

corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze

potenzialmente negative per l’ambiente e per la salute dell’essere umano.

Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie

apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti

pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel

quale avete acquistato il prodotto.

Declaration of Conformity

Česky

[Czech]

UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS

device, je ve shod se základními po adavky a dal ími p íslu n mi

ustanoveními sm rnice 1999/5/ES.

Dansk

[Danish]

Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende

udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav

og øvrige relevante krav i direktiv 1999/5/EF.

Nederlands

[Dutch]

Hierbij verklaart UBIQUITI NETWORKS dat het toestel UBIQUITI

NETWORKS device, in overeenstemming is met de essentiële eisen

en de andere relevante bepalingen van richtlijn 1999/5/EG.

Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI

NETWORKS device, voldoet aan de essentiële eisen en aan de

overige relevante bepalingen van Richtlijn 1999/5/EC.

English

Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI

NETWORKS device, is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Eesti

[Estonian]

Käesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITI

NETWORKS device, vastavust direktiivi 1999/5/EÜ põhinõuetele ja

nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Suomi

[Finnish]

UBIQUITI NETWORKS vakuuttaa täten että UBIQUITI NETWORKS

device, tyyppinen laite on direktiivin 1999/5/EY oleellisten

vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Français

[French]

Par la présente UBIQUITI NETWORKS déclare que l’appareil

UBIQUITI NETWORKS, device est conforme aux exigences

essentielles et aux autres dispositions pertinentes de la directive

1999/5/CE.

Deutsch

[German]

Hiermit erklärt UBIQUITI NETWORKS, dass sich diese UBIQUITI

NETWORKS device, in Übereinstimmung mit den grundlegenden

Anforderungen und den anderen relevanten Vorschriften der

Richtlinie 1999/5/EG befindet”. (BMWi)

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ UBIQUITI NETWORKS ΔΗΛΩΝΕΙ ΟΤΙ UBIQUITI

NETWORKS device, ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

1995/5/ΕΚ.

Magyar

[Hungarian]

Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a

UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ

követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Íslenska

[Icelandic]

Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS

device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í

tilskipun 1999/5/EC.

Italiano

[Italian]

Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI

NETWORKS device, è conforme ai requisiti essenziali ed alle altre

disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski

[Latvian]

Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device,

atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist

tajiem noteikumiem.

Lietuviškai

[Lithuanian]

UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS

įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB

Direktyvos nuostatas.

Malti

[Maltese]

Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITI

NETWORKS device, jikkonforma mal- ti ijiet essenzjali u ma

provvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Norsk

[Norwegian]

UBIQUITI NETWORKS erklærer herved at utstyret UBIQUITI

NETWORKS device, er i samsvar med de grunnleggende krav og

øvrige relevante krav i direktiv 1999/5/EF.

Slovensky

[Slovak]

UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKS

device, sp a základné po iadavky a v etky príslu né ustanovenia

Smernice 1999/5/ES.

Svenska

[Swedish]

Härmed intygar UBIQUITI NETWORKS att denna UBIQUITI

NETWORKS device, står I överensstämmelse med de väsentliga

egenskapskrav och övriga relevanta bestämmelser som framgår av

direktiv 1999/5/EG.

Español

[Spanish]

Por medio de la presente UBIQUITI NETWORKS declara que el

UBIQUITI NETWORKS device, cumple con los requisitos esenciales

y cualesquiera otras disposiciones aplicables o exigibles de la

Directiva 1999/5/CE.

Polski

[Polish]

Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt serii

UBIQUITI NETWORKS device, spełnia zasadnicze wymagania i inne

istotne postanowienia Dyrektywy 1999/5/EC.

Português

[Portuguese]

UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device,

está conforme com os requisitos essenciais e outras disposições da

Directiva 1999/5/CE.

Română

[Romanian]

Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv

UBIQUITI NETWORKS este în conformitate cu cerințele esențiale și

alte prevederi relevante ale Directivei 1999/5/CE.

Online Resources

Support support.ubnt.com

Community community.ubnt.com

Downloads downloads.ubnt.com

Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS,

EdgeRouter, and TOUGHCable are trademarks or registered trademarks of

Ubiquiti Networks, Inc. in the United States and in other countries. All other

trademarks are the property of their respective owners. JL060214

www.ubnt.com

Ubiquiti AM-V2G-TI Manualul utilizatorului

Marca: Ubiquiti

Model: AM-V2G-TI

Categorie: Convertoare media de rețea

Tip: Manualul utilizatorului

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ubiquiti AM-V2G-TI User guide
italiano: Ubiquiti AM-V2G-TI Guida utente

Ubiquiti AM-V2G-TI Manualul utilizatorului

Acest manual este potrivit și pentru

Ubiquiti AM-V2G-TI Manualul utilizatorului

în alte limbi

Lucrări conexe