Parkside PABS 18-Li B3 Operation and Safety Notes

IAN 90877

CORDLESS DRILL PABS 18-Li B3

AKKU-BOHRSCHRAUBER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

AKU ODVIJAČ

Upute za posluživanje i za Vašu sigurnost

Prijevod originalnih uputa za uporabu

ŞURUBELnIţă CU ACUmULAtOR

Instrucţiuni de utilizare şi de siguranţă

Traducerea instrucţiunilor de utilizare originale

АКУМУЛАТОРНА БОРМАШИНА

Инструкции за обслужване и безопасност

Превод на оригиналното ръководство за експлоатация

Ε

ΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ

Υποδείξει χειρισού και ασφαλεία

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

CORDLESS DRILL

Operation and Safety Notes

Translation of original operation manual

GB Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 15

RO Instrucţiuni de utilizare şi de siguranţă Pagina 25

BG Инструкции за обслужване и безопасност Страница 35

GR Υποδείξει χειρισού και ασφαλεία Σελίδα 45

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 55

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama

uređaja.

Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.

Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции

на уреда.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα ε τι εικόνε και εξοικειωθείτε ε όλε τι λειτουργίε τη

συσκευή.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A B

10

C

1

2

3

6

7

8

13

6

7

4

1415

9

5

11 12

5 GB

Table of contents

Introduction

Intended purpose ................................................................................................................................ Page 6

Equipment Components ......................................................................................................................Page 6

Scope of delivery ................................................................................................................................Page 6

Technical Data ....................................................................................................................................Page 6

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 8

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 9

Safety advice relating to cordless drill drivers ..................................................................................Page 9

Safety notices for chargers ................................................................................................................. Page 9

Supplementary Instructions .................................................................................................................Page 9

Original ancillaries / accessories .......................................................................................................Page 10

Start-up

Charging the battery pack .................................................................................................................Page 10

Insertion / removal of a battery pack into the appliance ..................................................................Page 10

Checking battery status ......................................................................................................................Page 10

Changing tools .................................................................................................................................... Page 10

Torque pre-selection ............................................................................................................................Page 11

2 Gear Drive .......................................................................................................................................Page 11

Operation

Switching On / Off .............................................................................................................................. Page 11

Setting the speed .................................................................................................................................Page 11

Switching direction of rotation ...........................................................................................................Page 11

Tips and Tricks ..................................................................................................................................... Page 11

Maintenance and Cleaning ..............................................................................................Page 12

Warranty .........................................................................................................................................Page 12

Disposal ............................................................................................................................................Page 12

Conformity Declaration / Manufacturer ................................................................Page 13

6 GB

Cordless drill PABS 18-Li B3

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Intended purpose

This appliance is designed for drilling and screwing

into wood, plastic and metal. Use the appliance only

as described and only for the purposes indicated.

Any other uses, and modiﬁcations to the appliance,

are deemed to be improper usage and may result

in serious physical injury. The manufacturer accepts

no responsibility for damage(s) resulting from

improper usage. The appliance is not intended for

commercial use.

Equipment Components

1

Gear selector switch

2

Direction of rotation switch / lock

3

ON / OFF Switch / R.P.M. regulator

4

Bit holder

5

Belt clip

6

Rechargeable battery pack

7

Battery pack release button

8

Rechargeable battery display LED

9

Rechargeable battery charge state button

10

LED working light

11

Drill chuck

12

Torque pre-selector

13

Fast charger

14

Red charge-control LED

15

Green charge-control LED

Scope of delivery

1 Cordless drill with rechargeable battery pack

1 Bit PH2 50 mm

1 Fast charger

1 Carry case

1 Directions for use

Technical Data

PABS 18-Li B3 Cordless drill:

Nominal voltage: 18 V

Idle-running speed: 1st gear: max. 400 min

-1

Idle-running speed: 2nd gear: max. 1400 min

-1

Drill chuck

clamping range: max. 13 mm

Maximum

drill diameter: Steel: 13 mm,

Wood: 30 mm

PABS 18-Li B3-1 Battery Pack:

Type: LITHIUM-ION

Nominal voltage: 18 V

Capacity: 1.3 Ah

Energy content: 23.4 Wh

PABS 18-Li B3-2 Fast Charger:

INPUT

Nominal voltage: 230–240 V∼, 50 Hz

Power input: 45 W

OUTPUT

Nominal voltage: 18 V

Charging current 1.5 A

Charging time: approx. 60 min

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 69 dB(A)

Sound power level: 80 dB(A)

Uncertainty K: 3 dB

Introduction / General safety advice for electrical power tools

Introduction

7 GB

Total vibration (vector sum of three directions) is

calculated in accordance with EN 60745:

Screwing: Vibration emission value

a

h

= 0.824 m / s

2

,

uncertainty K = 1.5 m / s

2

,

Drilling: Vibration emission value

a

h,D

= 2.47 m / s

2

,

uncertainty K = 1.5 m / s

2

.

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General safety advice for

electrical power tools

Read all the safe-

ty advice and instructions! Failure

to observe the safety advice and instruc-

tions may result in electric shock, ﬁre and / or seri-

ous injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools pow-

ered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) K

eep your working area clean and wel

l

lit. Untidy or poorly lit working areas can lead

to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases o

r

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c) Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose con-

trol of the device.

2. Electrical safety

a) The mains plug on the power tool (or

on the power supply) must ﬁt the

mains

socket. Never modify the plug in any

way. Never use adapter plugs with

earthed power tools. Unmodiﬁed plugs

and the correct sockets reduce the risk of elec-

tric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended, e.

g.

to carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains lead

away from heat, oil, sharp edges or

moving parts of the device. Damaged or

tangled mains leads increase the risk of elec-

tric shock.

e) When working outdoors with an elec-

trical power tool always use extension

cables that are also approved for use

outdoors. The use of an extension cable suit-

able for outdoor use reduces the risk of elec-

tric shock.

Introduction / General safety advice for electrical power tools

Introduction

8 GB

f) Use a residual current device (RCD) for

protection if operating the electrical

power tool in a moist environment is

unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety hel-

mets or ear protectors, appropriate to the type

of electrical power tool used and work under-

taken, reduces the risk of injury.

c) Avoid accidental starting. Verify the po-

wer tool is switched oﬀ before connec-

ting it to the mains and / or connecting

the battery, picking it up, or carrying it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing and

balance at all times. By doing this you will

be in a better position to control the device in

unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4. Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

General safety advice for electrical power tools

9 GB

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the cord-

less electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b) Only the rechargeable battery units

supplied are to be used with an elec-

trical power tool. The use of other recharge-

able battery units may lead to the danger of

injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

d) Fluids may leak out of rechargeable

battery units if they are misused. If this

happens, avoid contact with the ﬂuid.

If contact occurs, ﬂush the aﬀected area

with water. Seek additional medical

help if any of the ﬂuid gets into your

eyes. Escaping battery ﬂuid may cause skin

irritation or burns.

CAUTION! DANGER OF EXPLOSION!

The batteries must never be recharged!

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety advice relating to

cordless drill drivers

Hold the device by the

insulated handle surfaces when you

are undertaking work where there is

the danger of the screw striking hidden

electricity cables or the device’s mains

lead. Contact of the screw with a live wire could

cause metal parts of the device to become live

and lead to electric shock.

Safety notices for chargers

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsi-

ble for their safety. Children must never be

allowed to play with the device.

Supplementary Instructions

Securely support the workpiece. A workpiece

held in a clamp or vice is kept more securely in

place than one held by your hand.

POISONOUS DUSTS!

Harmful / noxious dusts generated from your

work represent a risk to the health of the person

operating the device and to anyone near the

work area. Wear safety glasses and a dust mask!

Do not drill any material containing

asbestos. Asbestos is a known carcinogen.

Hold the electrical power tool ﬁrmly.

High reaction torques may occur momentarily

during tightening or loosening of screws.

If the inserted tool jams, switch oﬀ the

electrical power tool immediately. Be

prepared for high reaction torques as they may

cause kickback. The inserted tool may jam if

the electrical power tool is overloaded or is

held at an angle to the workpiece.

Before you carry out any tasks on the

device, transport or store it, make sure

that the direction of rotation switch is

General safety advice for electrical power tools

10 GB

in the middle position (lock). To prevent

the device from starting up unintentionally.

DANGER! Take steps to ensure that

you do not hit upon any service lines

(electricity, gas, water) when work-

ing with electrical appliances. Check, if

need be with a service line detector, before

you start to cut or bore into a surface.

Original ancillaries /

accessories

Use only the ancillaries and accessories

that are detailed in the operating

instructions. The use of ancillaries and ac-

cessories other than those recommended in the

operating instructions could lead to an increased

risk of personal injury for you.

Start-up

Charging the battery pack

CAUTION! Always ensure the plug is removed

from the mains socket before inserting a battery pack

into, or removing one from, the charging station.

Never charge the battery pack if the ambient

temperature is less than 10 °C or greater than

40 °C.

1. Insert the battery pack

6

into the quick-

charger

13

(see Fig. C).

2. Insert the mains plug into the mains socket. The

ﬂashing green charge indicator LED

15

shows

that charging is in progress.

3. The charging process is completed when the

green charge indicator LED

15

light up and the

accumulator pack

6

is ready for operation.

4. If the red charge indicator LED

14

lights up, the

quick battery charger

13

is in standby mode;

the accumulator pack

6

is not connected.

5. If the red charge indicator LED

14

starts ﬂas-

hing, this means that the accumulator pack

6

has become too hot; no charging process.

Never charge the battery pack for a second time

immediately after a fast charging process has

been completed. This can give rise to the battery

pack becoming overcharged and to a reduced

service life of the battery and charging station.

Switch the charger oﬀ for at least 15 minutes

between two successive charging procedures.

Remove the power plug from the wall socket.

Insertion / removal of a battery

pack into the appliance

Inserting the rechargeable battery pack:

Move the rotation switch

2

into the middle

position (lock). Push the rechargeable battery

pack

6

into the handle until it engages.

Removing the rechargeable battery pack:

Press the release button

7

and remove the

rechargeable battery pack

Checking battery status

To check the battery status, press the battery

LED button

9

(refer to main diagram).

The three battery LEDs

8

indicate the condition

and the remaining charge as follows:

GREEN / RED / ORANGE = maximum charge /

capacity

RED / ORANGE = medium charge / capacity

RED = weak charge – recharge battery

Changing tools

Your cordless drill has a fully automatic spindle

lock

.

Once the motor has come to a halt, the drive shaft

is automatically locked, so that the chuck

11

can

be opened simply by turning it

.

After you have inserted the required bit and ﬁxed it

in place by turning the chuck

, you can immedi-

ately continue working. The spindle lock releases

itself automatically when the motor is started (by

operation of the ON / OFF switch

3

).

Start-up / Operation

General safety advice for electrical power tools / Start-up

11 GB

Torque pre-selection

You can adjust the torque by using

12

torque pre-

selection.

Select a low setting for small screws, soft work

material.

Select a high setting for large screws, hard

work materials and for the extraction of screws.

For drilling, push the selector to the setting for

drilling, in that you adjust the torque pre-selector

to the position

.

2 Gear Drive

CAUTION! Move the gear selector switch

1

only after the device has come to a standstill.

Failure to observe this advice may result in damage

to the device.

In the ﬁrst gear (Gear selector switch

1

in Position: 1)

A speed of up to approx. 400 rpm can be achieved

and a high torque. This setting is intended for use w

ith

all screwing tasks and for accessories (see example

Fig. B).

In the second gear (Gear selector switch

1

in Position: 2)

It achieves a speed of up to approx. 1400 rpm, for

the carrying out of drilling tasks (see example Fig. A).

Operation

Switching ON / OFF

Switching on:

To start the appliance squeeze on the ON /

OFF switch

3

and then keep it pressed down.

The LED working light

10

comes on with a slightly

or fully pressed ON /OFF switch

3

and illumi-

nates the working area in poor lighting conditio

ns.

Switching off:

To stop the appliance, release the ON / OFF

switch

3

.

Setting the speed

The ON / OFF switch

3

has a variable speed con-

trol device. Slight pressure on the ON / OFF switch

3

will cause the rotation speed to slow down. With

increased pressure, the rotational speed will increase.

Note: The integrated engine brake means that the

device will come to a fast standstill.

Switching direction of rotation

To switch the direction of rotation, push the

direction of rotation switch

2

to either the

right or to the left.

Tips and Tricks

Before you use the appliance, check to see

that the screw or drill bit is properly ﬁtted, i.e.

located centrally in the chuck.

Screw bits are designated with their dimensions

and their shape. If you are unsure, always try

the particular screw bit out to see whether it sits

in the screw head without any free play.

Torque:

Smaller screws and bits in particular can be

easily damaged if you adjust the appliance

with too high a torque and/or rotation speed.

Hard screwdriving conditions (into metal):

Particularly high torques can occur, for example

with metal screws tightened by socket tool bits.

Select a lower rotation speed.

Soft screwdriving conditions (e.g. into

soft wood):

You should also select a low speed in order not to

damage the wood workpiece surface through con

-

tact with the metal screw head. Use a countersinker.

When drilling into wood, metal and other

materials, take note of the following advice:

With small diameter drill bits use a high drill

speed. For large diameter drill bits, use a low

drill speed.

Start-up / Operation

General safety advice for electrical power tools / Start-up

12 GB

For hard materials, select a low drill speed.

For soft materials, select a high drill speed.

Secure or ﬁx down the workpiece (if possible)

in a clamp or vice.

Mark the intended position of the hole with a

centre punch or a nail and select a low drill speed

for drilling.

Take the rotating drill bit out of the hole frequently

so that swarf or drill dust can be re-moved and

the hole and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results,

you should cool the bit with oil. Metal drill bits

can also be used to drill into plastic.

Drilling in stone:

Use a circular shafted masonry drill bit with a

hardened metal tip.

Drilling in wood:

Normally you should use a wood drill with a

centring point. For deep holes, use an auger type

bit. For large diameter holes, use a forstner bit.

You can screw small screws into soft wood

without the need for pre-drilling.

Maintenance and Cleaning

RISK OF INJURY! Switch the

device oﬀ, unplug from the mains socket and re-

move the battery before performing any work on

the device.

The cordless drill is maintenance-free.

Always keep the device clean, dry and free of

oil or grease.

Use a dry cloth to clean the housing.

If the connection cable needs

to be replaced, this repair must be performed

by the manufacturer or a representative to pre-

vent safety hazards.

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tampering

not carried out by our authorized service branch. Your

statutory rights are not restricted in any way by this

warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0,10 GBP/Min.)

e-mail: k[email protected]

IAN 90877

Disposal

The packaging comprises exclusively en-

vironmentally-friendly material. Dispose

of it in your local recycling containers.

Disposal / Conformity Declaration / Manufacturer

Operation / Maintenance and Cleaning / Warranty / Disposal

13 GB

Do not dispose of electrical

appliances with your domestic

waste!

According to the European Directive 2002 / 96 / EC,

concerning used electrical and electronic appliances

and its implementation in national law, superannu-

ated electrical appliances must be collected and

disposed of via an environmentally suitable recy-

cling facility.

Do not dispose of rechargeable

batteries with your household

refuse!

Defective or worn out rechargeable batteries must

be recycled according to Directive 2006 / 66 / EC.

Dispose of batteries and appliances over the existing

collection facilities.

Your local communal or municipal authorities can

provide information on how to dispose of the worn

out appliance.

Conformity Declaration /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EC Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1:2009+A11, EN 60745-2-1:2010

EN 60745-2-2:2010, EN 55014-1:2006+A1+A2

EN 55014-2:1997+A1+A2, EN 61000-3-2:2006+

A1+A2, EN 61000-3-3:2008

EN 60335-1:2002+A1+A11+A12+A2+A13+A14+

A15, EN 60335-2-29:2004, EN 62233:2008

Type / Appliance Designation:

Cordless drill PABS 18-Li B3

Date of manufacture (DOM): 07–2013

Serial number: IAN 90877

Bochum, 31.07.2013

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of further development.

Disposal / Conformity Declaration / Manufacturer

Operation / Maintenance and Cleaning / Warranty / Disposal

14

15 HR

Popis sadržaja

Uvod

Uporaba u skladu sa namjenom .................................................................................................. Stranica 16

Oprema ......................................................................................................................................... Stranica 16

Opseg isporuke ............................................................................................................................. Stranica 16

Tehnički podaci ............................................................................................................................. Stranica 16

Opće sigurnosne upute za električni alat

1. Sigurnost na radnom mjestu .................................................................................................... Stranica 17

2. Električna sigurnost ................................................................................................................... Stranica 17

3. Sigurnost osoba ........................................................................................................................ Stranica 18

4. Pažljivo postupanje s električnim uređajima i njihovo korištenje ........................................... Stranica 18

5. Uporaba i rukovanje akumulatorskim alatom ........................................................................ Stranica 19

6. Servis ......................................................................................................................................... Stranica 19

Sigurnosne upute za akumulatorsku bušilicu ............................................................................... Stranica 19

Sigurnosne upute za punjače ....................................................................................................... Stranica 19

Dodatne upute .............................................................................................................................. Stranica 19

Originalna oprema / dodatni uređaji .......................................................................................... Stranica 20

Stavljanje u pogon

Punjenje paketa baterija ............................................................................................................... Stranica 20

Umetanje paketa baterija u uređaj / vađenje paketa baterija ................................................... Stranica 20

Provjeravanje aku-stanja ............................................................................................................... Stranica 20

Zamjena alata ............................................................................................................................... Stranica 20

Određivanje okretnog momenta unaprijed ................................................................................. Stranica 21

2-brzinski mjenjač ......................................................................................................................... Stranica 21

Rukovanje

Uključivanje / Isključivanje ............................................................................................................ Stranica 21

Podešavanje broja okretaja ......................................................................................................... Stranica 21

Promjena smjera okretanja ........................................................................................................... Stranica 21

Savjeti i trikovi ............................................................................................................................... Stranica 21

Održavanje i čišćenje ...................................................................................................... Stranica 22

Jamstveni list.......................................................................................................................... Stranica 22

Zbrinjavanje ........................................................................................................................... Stranica 23

Izjava o sukladnosti / Proizvođač ........................................................................ Stranica 23

16 HR

Uvod / Opće sigurnosne upute za električni alat

Uvod

Aku odvijač PABS 18-Li B3

Q

Uvod

Čestitamo Vam na kupnji novog uređaja. Ovom

kupnjom odlučili ste se za visokokvalitetan proizvod.

Uputa za uporabu je sastavni dio ovog proizvoda.

Ona sadrži važne upute o sigurnosti, uporabi i

uklanjanju otpada. Prije upotrebe proizvoda upoz-

najte se sa svim njegovim uputama za korištenje i

sigurnosnim uputama. Koristite ovaj proizvod u

skladu s navedenim uputama te u navedene svrhe.

Ukoliko proizvod dajete nekoj drugoj osobi, pre-

dajte toj osobi također i sve upute.

Q

Uporaba u skladu sa namjenom

Ovaj uređaj je namijenjen za bušenje i odvijanje u

drvetu, plastici i metalu. Koristite uređaj isključivo

na opisani način i u navedenim područjima primjene.

Svaki drugi način uporabe i svaka promjena uređaja

smatra se nenamjenskom i krije znatnu opasnost od

nastanka nezgode. Proizvođač ne preuzima odgo-

vornost od štete nastale uslijed korištenja uređaja

protivnog njegovoj namjeni. Uređaj nije namjenjen

za komercijalnu uporabu.

Q

Oprema

1

Prekidač za odabir stupnja brzine

2

Prekidač za odabir smjera okretanja / blokada

3

Prekidač Uklj.-Isklj. / Regulator broja okretaja

4

Držač bita

5

Pričvršćenje pojasa

6

Komplet akumulatora

7

Tipka za deblokiranje kompleta akumulatora

8

LED pokazivača akumutalora

9

Tipka stanje akumulatora

10

Radna LED-svjetiljka

11

Zaglavnik za svrdlo

12

Regulator za odabir okretnog momenta unaprijed

13

Uređaj za brzo punjenje

14

Crvena LED-signalizacija za kontrolu punjenja

15

Zelena LED-signalizacija za kontrolu punjenja

Q

Opseg isporuke

1 aku odvijač s u aku-pakovanjem

1 bit PH2 50 mm

1 uređaj za brzo punjenje

1 kovčeg za nošenje

1 uputstvo za uporabu

Q

Tehnički podaci

PABS 18-Li B3 aku odvijač:

nazivni napon: 18 V

broj okretaja u

praznom hodu: 1. hod: maksimalno

400 min

-1

broj okretaja u

praznom hodu: 2. hod: maksimalno

1400 min

-1

raspon zaglavnika za svrdlo: maksimalno 13 mm

maksimalan

promjer bušotine: čelik: 13 mm,

drvo: 30 mm

PABS 18-Li B3-1 aku-pakovanje:

tip: LITHIUM-ION

nazivni napon: 18 V

kapacitet: 1,3 Ah

sadržaj energije: 23,4 Wh

PABS 18-Li B3-2 uređaj za brzo punjenje:

ULAZ / Input:

nazivni napon: 230–240 V∼, 50 Hz

potrošnja: 45 W

IZLAZ / Output:

nazivni napon: 18 V

struja punjenja: 1,5 A

trajanje punjenja: oko 60 min

zaštitna klasa: II /

Informacija o buci i vibraciji:

Mjerna vrijednost za buku utvrđena sukladno

EN 60745. A-ocjenjena razina buke električnog

alata iznosi tipično:

Razina zvučnog tlaka: 69 dB(A)

Razina snage zvuka: 80 dB(A)

Nesigurnost K: 3 dB

17 HR

Ukupne vrijednosti titranja (vektorski zbroj triju

smjerova) su istražene sukladno EN 60745:

Vijak: Vrijednost emisije titranja

a

h

= 0,824 m / s

2

,

Nesigurnost K= 1,5 m / s

2

,

Bušenje: Vrijednost emisije titranja

a

h,D

= 2,47 m / s

2

,

Nesigurnost K= 1,5 m / s

2

.

Razina titranja, navedena u

ovim uputama, je istražena i određena sukladno

normiranom postupku mjerenja, koji je naveden u

EN 60745 i koji je prikladan za uspoređivanje stroja.

Navedena vrijednost emisije titranja se može koristiti

i za uvodnu procjenu izloženosti.

Razina titranja je promijenljiva, ovisno o korištenju

električnog alata, te može u pojedinim slučajevima

ležati iznad vrijednosti, navedene u ovim uputama.

Razina opterećenja titranja može biti podcjenjena,

ako se električni alat redovito koristi na takav način.

Uputa: Za precizno ocjenjivanje titrajnog otpere-

ćenja tijekom određenog radnog vremena, potrebno

je također uzeti u obzir vremena kad je stroj isključen,

ili je uključen ali se zapravo ne rabi. To može znatno

smanjiti titrajno opterećenje, tijekom cijelog radnog

vremena.

Opće sigurnosne upute

za električni alat

Pročitajte si-

gurnosne upute kao i sve ostale

upute! U slučaju ne pridržavanja sigur-

nosnih uputa kao i ostalih uputa, prijeti opasnost

od

strujnog udara, požara i / ili teških ozljeda.

Sačuvajte sve sigurnosne upute kao i sve

ostale upute za ubuduće!

U sigurnosnim uputa rabljeni izraz „električni alat“

odnosi se na električne uređaje sa mrežnim pogo-

nom (sa mrežnim kabelom) i na električni alat sa

akumulatorskim pogonom (bez mrežnog kabela).

1. Sigurnost na radnom mjestu

a) Vodite uvijek računa o tome, da Vaše

radno mjesto bude čisto i dobro os-

vjetljeno. Nered i ne osvjetljeno područje

rada, može uzrokovati nezgode.

b) Ne rabite stroj u području gdje prijeti

opasnost od eksplozije, gdje se nalaze

zapaljive tekućine, plinovi ili prašine.

Električni alati proizvode iskre, koje mogu za-

paliti prašinu ili pare.

c) Za vrijeme uporabe električnog alata,

držite djecu i druge osobe izvan doh-

vata istoga. U slučaju nepažnje, možete

izgubiti kontrolu nad strojem.

2. Električna sigurnost

a) Mrežni utikač uređaja mora odgova-

rati utičnici.

Utikač se ni na kakav

način

ne smije mijenjati. Ne koristite adap-

terske utičnice zajedno s zaštitno uze-

mljenim uređajima. Neizmijenjeni utikači

i odgovarajuće utičnice smanjuju rizik električ-

nog udara.

b) Izbjegavajte dodir tijela s uzemljenim

površinama kao što su cijevi, radijatori

,

pećnice i hladnjaci. Postoji povećana opa-

snost od električnog udara ukoliko je vaše tijelo

uzemljeno.

c) Uređaj držite podalje od kiše i vlage.

Prodiranje vode u unutrašnjost uređaja pove-

ćava opasnost električnog udara.

d) Ne koristite kabel u neke druge svrhe,

npr. za nošenje uređaja, vješanje ure-

đaja ili za izvlačenje utikača iz utičnice.

Kabel držite podalje od topline, ulja,

oštrih rubova i pokretnih dijelova ure-

đaja. Oštećeni ili spetljani kabel ili utikač po-

većava rizik električnog udara.

e) Kod rada na otvorenome koristite

samo

produžni kabel koji je dozvoljen za

korištenje na otvorenome. Upotreba

produžnog kabla namijenjenog za korištenje n

a

otvorenome smanjuje rizik električnog udara.

f) Ako je korištenje električnog alata u

vlažnim prostorima neizbježno, rabite

Uvod / Opće sigurnosne upute za električni alat

Uvod

18 HR

Opće sigurnosne upute za električni alat

zaštitnu strujnu sklopku. Korištenje zaštitne

strujne sklopke, smanjuje rizik strujnog udara.

3. Sigurnost osoba

a) Budite uvijek pozorni, vodite računa

o tome što radite i razumno pristupite

radu s električnim alatom. Ne rabite

stroj, ako ste umorni ili pod utjecajem

droga, alkohola ili lijekova. Jedan trenu

tak

nepažnje za vrijeme korištenja stroja, može

uzrokovati teške ozljede.

b) Nosite osobnu zaštitnu opremu i uvijek

zaštitne očale. Korištenje osobne zaštitne

opreme, kao maske za prašinu, protuklizne

zaštitne cipele, zaštitnu kacigu ili štitnik za uši,

ovisno o vrsti i uporabi električnog alata,

smanjuje rizik od ozljeda.

c) Spriječite slučajno uključenje. Uvjerite

se u to, da je električni alat isključen,

prije uključenja na struju, podizanja

ili nošenja. Ako pri nošenju uređaja držite

prst na sklopki za UKLJUČENJE / ISKLJUČE-

NJE ili ako je uređaj uključen, prijeti opasnost

od nezgode.

d) Prije uključenja stroja, uklonite alat

za podešavanje ili vijčani ključ. Alat ili

ključ, koji se nalazi u rotirajućem dijelu stroja,

može prouzročiti ozljede.

e) Izbjegavajte nenaravan polažaj tijela.

Vodite računa o tome da sigurno stojite

na tlu i održavate vlastitu ravnotežu.

Na taj način bolje možete kontrolirati uređaj,

posebno u neočekivanim situacijama.

f) Nosite prikladnu odjeću. Ne nosite

široku odjeću ili nakit. Držite kosu,

odjeću i rukavice dalje od pomičnih

dijelova. Opuštena odjeća, nakit ili duga

kosa mogu biti zahvaćeni od pomičnih dijelova.

g) Ako se montira uređaje za usisavanje

i prihvaćanje prašine, uvjerite se u

to da su priključeni i da se pravilno

koriste. Uporaba tih uređaja, smanjuje

ugrožavanje od prašine.

4. Pažljivo postupanje s

električnim uređajima i

njihovo korištenje

a) Nemojte uređaj preopterećivati.

Koristite onaj električni uređaj koji

odgovara za Vaš rad. S odgovarajućim

električnim uređajem bolje i sigurnije ćete radi-

ti u navedenom području rada.

b) Ne koristite električni uređaj s neisprav-

nim prekidačem. Električni uređaj koji se više

ne može uključiti i isključiti opasan je i treba ga

dati popraviti.

c) Izvucite utikač iz utičnice i / ili otklonite

akumulator, prije namještanja uređaja,

zamjene pribora ili odlaganja uređaja.

Ta mjera zaštite spriječava slučajno uključenje

električnog alata.

d) Čuvajte ne korišteni električni uređaj

tako da nije na dohvatu djeci. Ne

dopustite da uređaj koriste osobe

koje s njim nisu upoznate ili koje nisu

pročitale upute. Električni alati su opasni

kada ih korite osobe bez iskustva.

e) Pažljivo održavajte uređaj. Kontroli-

rajte da li pokretni dijelovi uređaja

besprijekorno funkcioniraju i da ne

zapinju, da dijelovi nisu slomljeni ili

tako oštećeni da je funkcija uređaja

upitna. Molimo da oštećene dijelove

dadete popraviti prije korištenja ure-

đaja. Brojne nesreće imaju uzrok zbog loše

održavanih električnih alata.

f) Alat za rezanje treba biti oštar i čist.

Brižljivo njegovani alat za rezanje sa oštrim

reznim rubovima, manje zaglavi i jednostavniji

je za rukovanje.

g) Rabite električni alat, opremu i ugrad-

ni alat, itd. sukladno ovim uputama i

na način kako je propisano za ovaj

posebni tip uređaja. Pri tome uzmite

u obzir radne uvjete i rad koji se izvodi.

Uporaba električnog alata za drugu osim

predviđene primjene, može uzrokovati opasne

situacije.

Opće sigurnosne upute za električni alat

19 HR

5. Uporaba i rukovanje

akumulatorskim alatom

a) Koristite samo one akumulatore koje

je preporučio proizvođač. Kod električnih

uređaja za koje su namijenjene samo određene

vrste akumulatora, postoji opasnost od izbijanja

požara ako se koriste sa drugim vrstama aku-

mulatora.

b) Akumulatore koristite samo u za njih

posebno namijenjenim uređajima.

Upotreba drugih akumulatora može dovesti

do ozljeda i opasnosti od izbijanja požara.

c) Držite neupotrjebljene akumulatore

daleko od kontakta s metalnim pred-

metima poput uredskih spajalica,

kovanica, ključeva, čavala i sl. Malih

metalnih predmeta koji bi mogli prouzročiti

prekid kontakta. Nakon takvog kontakta bi mo-

gao uslijediti kratki spoj koji bi za posljedicu

mogao imati opekline ili čak prouzročiti požar.

d) Kod neispravne upotrebe iz akumulato-

ra može iscuriti tekućina. Izbjegavajte

svaki kontakt s tom tekućinom. Nakon

mogućeg kontakta obavezno mjesto

kontakta isperite vodom. Ako tekućina

dođe u dodir s očima, odmah potražite

pomoć liječnika. Tekućina iz akumulatora u

kontaktu s kožom može prouzročiti ozljede i

opekline kože.

OPREZ! OPASNOST OD EKSPLOZIJE!

Nikada ne punite baterije koje nisu punjive!

6. Servis

a) Električne naprave smiju popravljati

samo ovlašteni serviseri ili električari.

Time ćete zadržati sigurnost vaših uređaja.

Sigurnosne upute za

akumulatorsku bušilicu

Držite uređaj na izoli-

ranim držkama, dok izvodite radove

pri kojima vijak može zahvatiti skrive-

ne električne vodove ili vlastiti mrežni

kabel. Dodir vijka sa vodom pod naponom

može također metalne dijelove uređaja staviti

pod napon i prouzročiti strujni udar.

Sigurnosne upute za punjače

Ovaj uređaj nije namijenjen osobama (uključivši

djecu) s ograničenim tjelesnim, senzoričnim ili

umnim sposobnostima i / ili koje nemaju iskustvo

ili znanje u ophođenju s uređajem, osim ako su

pod nadzorom osobe koja je zadužena za nji-

hovu sigurnost ili ako bi rabili uređaj prema

njenim uputama. Dijeca trebaju biti pod nadzo-

rom, kako se nebi igrala s uređajem.

Dodatne upute

Učvrstite predmet koji obrađujete. Koristite za-

tezne naprave ili škripac kako bi učvrstili pred-

met. Na taj način naprava je bolje učvršćena

nego vašom rukom.

OTROVNI PRAH !

Tijekom upotrebe naprave nastaju opasne /

otrovne čestice prašine koje mogu prouzročiti

opasnosti po zdravlje osoba koje se koriste

napravom ili osoba u neposrednoj blizini. Tije-

kom rada sa napravom uvijek koristite zaštitne

naočale i masku za zaštitu od prašine!

Ne obrađujte nikad materijale koji

sadrže azbest. Azbest izaziva rak.

Električni uređaj držite čvrsto u ruci.

Kod zatezanja i odvrtanja vijaka, može doći

do brzih i snažnih momenata otporne reakcije

uređaja.

Odmah isključite električni uređaj iz

struje u slučaju smetnji ili blokade ure-

đaja. Budite izuzetno oprezni kod rada stroja

i momenata reakcije ,koji mogu prouzročiti po-

vratni udarac. Alat kojim radite blokira, ako

dođe do preopterećenja električnog uređaja ili

ako se alat zaglavi u predmetu koji obrađujete.

Kod radova na uređaju, kao i kod

transporta, odnosno pospremanja

uređaja, obratni sklopnik (zaporka)

postavite na srednju poziciju. Tako ćete

priječiti ne namjerno uključivanje uređaja.

Opće sigurnosne upute za električni alat

20 HR

Opće sigurnosne upute za električni alat / Stavljanje u pogon

OPASNOST! Provjerite, da ne naletite

na vodove struje, vode ili plina, kada

radite sa električnim uređajima. Eventu-

alno izvršite provjeru pomoću uređaja za traže-

nje vodova, prije nego što bušite ili otvarate zid.

Q

Originalna oprema /

dodatni uređaji

Upotrebljavajte isključivo opremu i

dodatne uređaje navedene u uputama

za uporabu. Uporaba drugih alata i druge

opreme, koja nije navedena u ovim uputama,

može dovesti do opasnosti od ozljeda.

Stavljanje u pogon

Q

Punjenje paketa baterija

OPREZ! Uvijek izvucite mrežni utikač prije

vađenja paketa baterija iz punjača ili prije njegovog

postavljanja.

Nikada ne punite paket baterija, kada je vanj-

ska temperatura ispod 10 °C ili iznad 40 °C.

1. Stavite akumulatore

6

u uređaj za brzo pu-

njenje

13

(vidi sliku C).

2. Utaknite mrežni utikač u utičnicu. LED za kontro-

lu punjenja

15

koja sad treperi zeleno, pokazuje

postupak punjenja.

3. Odmah čim LED za kontrolu punjenja

15

pre-

stane treperiti i stalno svijetli zeleno, postupak

punjenja je okončan, te se baterijski sklop

6

može odmah koristiti.

4. Ukoliko LED za kontrolu punjenja

14

zasvijetli

zeleno, punjač za brzo punjenje

13

nalazi se u

Standby-modu; baterijski sklop

6

nije priključen.

5. Ukoliko LED za kontrolu punjenja

14

zasvijetli

crveno, baterijski sklop

6

je postao prevruć;

postupak punjenja je prekinut.

Nikada ne vršite ponovno punjenje paketa

baterija neposredno nakon jednog brzog pu-

njenja. Postoji opasnost da se paket baterija

prepuni, nakon čega bi vijek trajanja punjača i

same baterije bio skraćen.

Punjač između dva postupka punjenja isključite

na minimalno 15 minuta. U tu svrhu izvucite

mrežni utikač.

Q

Umetanje paketa baterija u

uređaj / vađenje paketa baterija

Postavljanje kompleta akumulatora:

Namjestite preklopnika smjera vrtnje

2

na

srednji položaj (blokiranje). Pustite da se akku-

komplet

6

zaglavi u drški.

Vađenje aku-pakovanja:

Pritisnite tipku za deblokiranje

7

i izvadite

aku-pakovanje.

Q

Provjeravanje aku-stanja

Pritisnite za provjeravanje aku-stanja tipku

Akku-LED

9

(vidi također glavni prikaz).

Stanje odnosno ostatak snage bit će prikazan

pomoću tri akku-LED-žaruljice

8

na slijedeći

način:

ZELENO / CRVENO / NARANČASTO = mak-

simalno punjenje / kapacitet

CRVENO / NARANČASTO = srednje punje-

nje / kapacitet

CRVENO = slabo punjenje – aku puniti

Q

Zamjena alata

Vaša akumulatorska bušilica i odvijač ima potpuno

automatsko aretiranje vretena

.

Kada motor miruje, dolazi do blokade pogonske

osovine, tako da steznik za brzo umetanje svrdla

11

možete otvoriti

okretanjem.

Nakon što ste umetnuli željeni alat i nakon što ste

ga okretanjem steznika

učvrstili, možete odmah

nastaviti sa radom. Blokada igle automatski se otpušta

pokretanjem motora (aktiviranje prekidača Uklj. /

Isklj.

3

).

Pagina se încarcă ...

Parkside PABS 18-Li B3 Operation and Safety Notes

Acest manual este potrivit și pentru

Parkside PABS 18-Li B3 Operation and Safety Notes

Lucrări conexe

Alte documente