Yamaha CP4 Stage Manualul proprietarului

Marca: Yamaha

Model: CP4 Stage

Categorie: Echipamente muzicale

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

Owner’s Manual

STAGE PIANO

2 CP4 STAGE/CP40 STAGE Owner’s Manual

SPECIAL MESSAGE SECTION (for CP4 STAGE)

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these graph-

ics on the enclosure. The explanation of these graphics

appears on this page. Please observe all cautions indicated

on this page and those indicated in the safety instruction sec-

tion.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important operat-

ing and maintenance (servicing) instruc-

tions in the literature accompanying the

product.

The lightning flash with arrowhead sym-

bol, within the equilateral triangle, is

intended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufficient magnitude to constitute a

risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is prop-

erly installed and used in its normal and customary manner,

all foreseeable risks have been eliminated. DO NOT modify

this unit or commission others to do so unless specifically

authorized by Yamaha. Product performance and/or safety

standards may be diminished. Claims filed under the

expressed warranty may be denied if the unit is/has been

modified. Implied warranties may also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The infor-

mation contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to

change or modify any of the specifications without notice or

obligation to update existing units.

ENVIRONMENTAL ISSUES: Yamaha strives to produce

products that are both user safe and environmentally

friendly. We sincerely believe that our products and the pro-

duction methods used to produce them, meet these goals. In

keeping with both the letter and the spirit of the law, we

want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargeable battery which (if applicable) is soldered in

place. The average life span of this type of battery is approx-

imately five years. When replacement becomes necessary,

contact a qualified service representative to perform the

replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away from

children. Dispose of used batteries promptly and as regu-

lated by applicable laws. Note: In some areas, the servicer is

required by law to return the defective parts. However, you

do have the option of having the servicer dispose of these

parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and fed-

eral regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the manu-

facturer’s warranty, and are therefore the owners responsi-

bility. Please study this manual carefully and consult your

dealer before requesting service.

NAME PLATE LOCATION: The graphic below indicates

the location of the name plate. The model number, serial

number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this

manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

92-469- 1 (rear)

CP4 STAGE/CP40 STAGE Owner’s Manual 3

SPECIAL MESSAGE SECTION (for CP40 STAGE)

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING:

Do not place this product in a position where anyone

could walk on, trip over, or roll anything over power or connecting cords

of any kind. The use of an extension cord is not recommended! If you

must use an extension cord, the minimum wire size for a 25’ cord (or

less) is 18 AWG. NOTE: The smaller the AWG number, the larger the

current handling capacity. For longer extension cords, consult a local

electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or mod-

ify any of the specifications without notice or obligation to update exist-

ing units.

This product, either alone or in combination with an amplifier and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult

an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and/or accessory mounting

fixtures that are either supplied with the product or as optional accesso-

ries. Some of these items are designed to be dealer assembled or

installed. Please make sure that benches are stable and any optional

fixtures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your

dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately five years. When replacement becomes nec-

essary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating

and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all local,

state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist

you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the rear of the product. The model num-

ber, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of

purchase in the spaces provided below and retain this manual as a per-

manent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP

(rear)

CAN ICES-3 (B)/NMB-3(B)

AC adaptor

(can_b_02)

4 CP4 STAGE/CP40 STAGE Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the

cord, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• (For CP40 STAGE) Use the specified adaptor (page 54) only. Using

the wrong adaptor can result in damage to the instrument or

overheating.

• (For CP4 STAGE) Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• (For CP4 STAGE) Be sure to connect to an appropriate outlet with a

protective grounding connection. Improper grounding can result in

electrical shock. (For details on grounding, see page 15.)

• This instrument contains no user-serviceable parts. Do not open the

instrument or attempt to disassemble or modify the internal

components in any way. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualified

Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or

wet conditions, place on it any containers (such as vases, bottles or

glasses) containing liquids which might spill into any openings. If

any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet.

Then have the instrument inspected by qualified Yamaha service

personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

• When one of the following problems occurs, immediately turn off

the power switch and disconnect the electric plug from the outlet.

Then have the device inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

Power supply/Power cord (CP4 STAGE)

Power supply/AC power adaptor (CP40 STAGE)

Do not open

Water warning

Fire warning

If you notice any abnormality

DMI-5 1/2

CP4

IMPORTANT SAFETY INSTRUCTIONS (for CP4 STAGE)

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong is provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

(UL60065_03)

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CP4 STAGE/CP40 STAGE Owner’s Manual 5

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality, or

possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord can

damage it.

• Remove the electric plug from the outlet when the instrument is not

to be used for extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• (For CP4 STAGE) Do not place objects in front of the instrument’s

air vent, since this may prevent adequate ventilation of the internal

components, and possibly result in the instrument overheating.

• Before moving the instrument, remove all connected cables, to

prevent damage to the cables or injury to anyone who might trip

over them.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug from

the outlet. Even when the power switch is turned off, electricity is

still flowing to the product at the minimum level. When you are not

using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Before connecting the instrument to other electronic components,

turn off the power for all components. Before turning the power on

or off for all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

instrument to set the desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps

on the panel or keyboard. This could cause physical injury to you or

others, damage to the instrument or other property, or operational

failure.

• (For CP4 STAGE) Do not insert anything into the instrument’s air

vent. This could cause physical injury to you or others, damage to

the instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons, switches

or connectors.

• Do not use the instrument/device or headphones for a long period of

time at a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or

ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

(For CP40 STAGE) Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the

minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Power supply/Power cord (CP4 STAGE)

Power supply/AC power adaptor (CP40 STAGE)

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

6 CP4 STAGE/CP40 STAGE Owner’s Manual

NOTICE

To avoid the possibility of malfunction/damage to the product, damage to data, or damage to other property, follow the

notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise,

the instrument, TV, or radio may generate noise. When you use the instrument along with an application on your iPad, iPhone

or iPod touch, we recommend that you set “Airplane Mode” to “ON” on that device in order to avoid noise caused by

communication.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or

unstable operation.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-

impregnated wiping cloths.

• During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the

instrument. If water is left, the wooden parts may absorb the water and be damaged. Make sure to wipe any water off

immediately with a soft cloth.

 Saving data

• Data in the Edit Buffer will be lost, when you turn off the power to the instrument. Store the data in User Memory, or save it on

external devices, such as a USB flash-memory device or a computer. (For details on the Edit Buffer and User Memory, see the

Reference Manual pdf document.)

• Data stored in User Memory may be lost due to malfunction or incorrect operation. Save any important data on external

devices, such as a USB flash-memory device or a computer.

• To protect against data loss through media damage, we recommend that you save your important data onto two USB flash-

memory devices or computers.

Information

 About copyrights

• Copying of the commercially available data, including, but not limited to, MIDI data and/or audio data is strictly prohibited

except for your personal use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to

which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software,

style files, MIDI files, Wave data, musical scores and sound recordings. Any unauthorized use of such programs and contents

outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T

MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• This device is capable of using various types/formats of music data by optimizing them to the proper format music data for

use with the device in advance. As a result, this device may not play them back precisely as their producers or composers

originally intended.

 About this manual

• The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat

different from those on your instrument.

• In cases where no significant difference exists between CP4 STAGE and CP40 STAGE diagrams and screen images, those

corresponding to CP4 STAGE are shown in this manual.

• Square brackets indicate buttons from the control panel in addition to jacks and terminals from the rear panel.

• Windows is a registered trademark of Microsoft

Corporation in the United States and other countries.

• Apple, Mac, Macintosh, iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective

companies.

• Specifications and descriptions in this Owner's Manual are for information purposes only. Yamaha Corporation reserves the

right to modify products or specifications at any time without prior notice. Since specifications, equipment, and options may

not be the same in every locale, please check with your Yamaha dealer. For the most up-to-date information, please download

the latest version (pdf) from the following web page:

http://download.yamaha.com/

CP4 STAGE/CP40 STAGE Owner’s Manual 7

Welcome

Thank you for purchasing the Yamaha CP4 STAGE or CP40 STAGE Stage Piano. Please read this owner’s manual

carefully before using the instrument in order to take full advantage of its various features. When you have finished

reading the manual, keep it in a safe, accessible place, and refer to it when you need to better understand an operation

or function.

Accessories

• Owner’s Manual (this book)

• Power cord (CP4 STAGE) / Power adaptor (CP40 STAGE)*

• Foot pedal (FC3A)

*May not be included in your area. Please check with your Yamaha dealer.

Using the Manuals

Four different manuals have been prepared for your CP4 STAGE or CP40 STAGE — this Owner’s Manual, the Reference

Manual, the Synthesizer Parameter Manual, and the Data List. A hard-copy version of the Owner’s Manual comes

together with the instrument, and the other three manuals are provided as pdf files on the Yamaha Downloads web page

(described later).

 Owner’s Manual (this booklet)

This Owner’s Manual describes how to set up your CP4 STAGE or CP40 STAGE and perform basic operations. This is the

document you should read first when you start playing and using the instrument.

 Reference Manual (pdf document)

The Reference Manual describes the design of the CP4 STAGE and CP40 STAGE and all of the parameters that may be

set. The manual includes the following:

Design of the CP4 STAGE & CP40 STAGE

•Makeup

• Controllers

• Tone Generator

• Effect Unit

•Memory

Reference

• Performances

• File Area

• Utility Area

Appendix

•MIDI

 Synthesizer Parameter Manual (pdf document)

The Synthesizer Parameter Manual provides a description of Voice parameters, effect types, effect parameters, and MIDI

messages often used on Yamaha electronic instruments. We recommend that you first read this Owner’s Manual and the

Reference Manual, and then refer to the Synthesizer Parameter Manual if you wish to know more about a specific Voice

parameter, effect, or the like.

 Data List (pdf document)

The Data List provides tables of the Voices, Performances, and effects found on the CP4 STAGE and CP40 STAGE in

addition to MIDI-related content.

8 CP4 STAGE/CP40 STAGE Owner’s Manual

How to use the PDF manuals

The Reference Manual, the Synthesizer Parameter Manual, and the Data List are provided as data documents in PDF

format. The PDF manuals listed above can be obtained from the Yamaha Downloads web page. To do so, go to the

web page using the following URL, enter “CP4” or “CP40” into the “Model Name” field, and then click “Search.”

Yamaha Downloads:

http://download.yamaha.com/

These PDF files can be viewed and read on a computer. When using Adobe

Reader

to view a PDF file, you can

search for specific words, print a specific page or link to open a desired section in the manual. The term search and

link functions are especially convenient methods of navigating through a PDF file, and we recommend that you use

them. The latest version of Adobe Reader can be downloaded from the following URL.

http://www.adobe.com/products/reader

Latest firmware version

Yamaha may from time to time update product firmware and the other associated software without prior notice. We

recommend that you check our web site for later releases and upgrade the firmware of your CP4 STAGE/CP40 STAGE

or the associated software.

http://www.yamahasynth.com/

Note that the explanations in this Owner’s Manual apply to the version of firmware released when this Owner’s Manual

was produced. For details on additional functions in later releases, refer to the above web site.

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authori-

ties or dealer and ask for the correct method of disposal.

(weee_eu_en_02)

CP4 STAGE/CP40 STAGE Owner’s Manual 9

Principal Features

 Authentic acoustic- and electric-piano sounds of unparalleled quality

Building on our decades of accomplishment in the production of stage pianos, we have delicately adjusted the sound of

each individual key and realized perfect balance over the full length of the keyboard, creating full-bodied piano tones

ideal for solo performances and ever-present sounds well suited for playing within an ensemble. Furthermore, by

analyzing and replicating the sound-producing mechanisms of classic electric pianos using cutting-edge technologies,

we have been able to achieve an extremely smooth response in the CP4 STAGE and CP40 STAGE keyboards. Through

the modeling both of original pre-amplifiers and of effectors responsible for the rich variety of tones indispensable to

quality sound production, we have faithfully reproduced many electric piano sounds now regarded as classics.

 Wealth of voices and effects for greater flexibility in live performances

In addition to piano voices, your CP4 STAGE or CP40 STAGE also offers a diverse selection of other musical instruments,

such as strings, guitar, and bass. With many versatile effects such as choruses and flangers also built-in, you can easily

create a rich tapestry of different sounds for your stage performances.

 Weighted hammer-action, 88-key keyboards that feel just like the real thing

The CP4 STAGE and CP40 STAGE employ an 88-key keyboard with a weighted hammer-action design that is virtually

indistinguishable from an actual piano. The CP4 STAGE also features a wooden keyboard.

 Easy overlaying and division of keyboard zones

Using your stage piano’s layering and splitting functions, you can easily layer the Parts that make up each Performance

or assign them to specific left-hand and right-hand zones.

 Record and playback functions for audio

Your CP4 STAGE or CP40 STAGE can record keyboard performances as audio data (Wave files) on a USB flash-memory

device. Wave files from a USB flash-memory device can also be played back as backing tracks for your performances.

What’s more, you can also connect a portable music player and output its audio from the stage piano together with the

music being played on the instrument.

 Convenient master-keyboard function

Using your stage piano’s master-keyboard function, which has been specially crafted for use in live-performance

settings, up to four virtual zones can be set up along the keyboard and assigned to four different tone generators,

including other MIDI instruments.

10 CP4 STAGE/CP40 STAGE Owner’s Manual

Table of Contents

PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using the Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Principal Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Component Names & Functions 12

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting Up 15

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Turning On and Off the Stage Piano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Adjusting Volume and LCD Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Basic Operations & Display Content 19

Cursor Types & Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing & Setting Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Displaying Menus & Making Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Changing Panes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Entering Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Exiting from the Current Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Performances 21

Parts Within a Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Changing Performances & Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Quick Start Guide 22

Playing Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Layering Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Splitting the Keyboard for Left and Right Hands . . . . . . . . . . . . . . . . . . . . . 25

Practicing with the Metronome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Changing Sounds Using Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Raising or Lowering the Pitch of Keyboard Notes . . . . . . . . . . . . . . . . . . . . 29

Storing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Selecting a Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

CP4 STAGE/CP40 STAGE Owner’s Manual 11

Creating Your Own Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Recording Your Playing as Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Playing Audio Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

File Operations Using a USB Flash-Memory Device . . . . . . . . . . . . . . . . . . 39

Configuring Utility Settings for the Overall System. . . . . . . . . . . . . . . . . . . . 41

Using with a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using with a Portable Music Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Using with Other MIDI Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Appendix 48

Shift Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

On-screen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

12 CP4 STAGE/CP40 STAGE Owner’s Manual

Component Names & Functions

Control Panel

(Illustration shows the CP4 STAGE.)

Pitch bend wheel (page 28)

Use this controller to raise or lower the pitch of played

notes in a continuously variable manner.

Modulation wheel (page 28)

Use this controller to add varying degrees of vibrato and

other effects to played notes.

[MASTER VOLUME] dial (page 18)

Turn this dial to adjust the overall volume of the stage

piano.

Part buttons (page 23)

The following Part buttons control different Parts:

[MAIN] button

Press to activate the Solo function and turn off all Parts

other than the MAIN Part.

[LAYER] button

[SPLIT] button

On the CP4 STAGE, the [LAYER] and [SPLIT] buttons can

be used to toggle on and off the corresponding Parts; on

the CP40 STAGE, both of these buttons toggle on and off

the SPLIT/LAYER Part. On both the CP4 STAGE and

CP40 STAGE, the MAIN Part is always on and cannot be

turned off.

[PART SELECT] button (page 23)

Use this button to change the currently selected Part.

Part sliders (page 28)

Use these sliders to adjust three parameters (Volume,

Chorus, and Reverb) for each of the Parts.

[SLIDER FUNCTION] button (page 28)

Use this button to change the parameter currently

assigned to the Part sliders (

). Each time you press this

button, the assigned parameter will change and the

indicator lights to its left will turn on and off to show the

current assignment.

[METRONOME] button (page 27)

Use this button to toggle the metronome on and off.

AUDIO PLAY/REC buttons (pages 35 and 36)

Use these buttons to control the playback and recording

of audio files.

[] (Stop) button

This button is used to stop playback and recording of an

audio file.

[ ] (Play) button

This button is used to start playback and recording of an

audio file. The indicator light above it will turn on during

playback and recording.

[ ] (Record) button

This button is used to open the screen for recording an

audio file. The indicator light above it will turn on during

recording.

[CHORUS] and [REVERB] SYSTEM EFFECT

buttons (page 34)

Use these buttons to toggle the instrument’s main chorus

and reverb effects on and off.

[A] and [B] PART EFFECT buttons (page 34)

Use these buttons to toggle Insertion Effect A and

Insertion Effect B on and off.

[MASTER COMP] button (page 42)

Use this button to toggle the instrument’s master

compressor on and off.

A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3

CP4 STAGE/CP40 STAGE Owner’s Manual 13

Component Names & Functions

[-] and [+] TRANSPOSE buttons (page 29)

Use these buttons to raise and lower the pitch of the

keyboard in steps of one semitone.

[FILE] button (page 39)

Use this button to open the File area in order to perform

file-related operations on the instrument itself or on the

connected USB flash-memory device.

[UTILITY] button (page 41)

Use this button to open the Utility area in order to set

parameters that affect the instrument as a whole.

[EDIT] button (page 31)

Use this button to edit Performances (page 21) and also

to compare edited and unedited versions. (For details on

the Compare Performance function, see the Reference

Manual (pdf).)

[STORE] button (pages 30 and 34)

Use this button to store Performances and Utility settings.

LCD (Liquid Crystal Display) (page 19)

Using the LCD, you can confirm system messages,

parameter settings, and a range of other information

depending on the function currently being used.

Data Dial (page 19)

Use this dial to change the value indicated by the on-

screen cursor.

[-1/NO] and [+1/YES] buttons (page 19)

Use these buttons to increase or decrease the value

indicated by the on-screen cursor in single units.

[PERFORMANCE PLAY/SELECT] button

(page 30)

Use this button to open the screen for selecting

Performances.

[PANEL LOCK] button (page 42)

Use this button to toggle the Panel Lock function on and

off. When on, control panel operations will be

deactivated.

[SHIFT] button (page 48)

Use this button in combination with others to perform a

range of different operations.

[EXIT] button (page 20)

The functions accessible using the stage piano’s screens

are arranged in a hierarchical structure. Press this button

to leave the current screen and move one step back

towards the top of the current area.

[ENTER] button

Use this button to make menu selections and confirm

settings. It can also be used to execute a range of

functions.

[ ], [ ], [ ], and [] (Cursor) buttons

(page 19)

Use these buttons to move the cursor on-screen in the

corresponding direction and to move between screen’s

panes.

Voice Category buttons (page 22)

Use these buttons to select different Voice categories.

MASTER EQUALIZER (EQ) sliders (page 29)

Use these sliders to adjust the gain in the corresponding

master-EQ frequency band.

C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

14 CP4 STAGE/CP40 STAGE Owner’s Manual

Component Names & Functions

Rear Panel

CP4 STAGE

CP40 STAGE

[] switch (page 17)

On the CP4 STAGE, this Power switch turns the stage

piano on ( ) and off (). On the CP40 STAGE, it is

known as the Standby/On switch and sets the instrument

to on ( ) or Standby mode ( ).

[AC IN] jack (page 15)

Use this jack for the power cord that came with the

instrument.

DC IN jack (page 15)

Use this jack for the power adaptor that came with the

instrument.

Music stand attachment holes

Use these two holes to attach a music stand (sold

separately).

[PHONES] jack (page 16)

Use this standard 1/4” stereo audio jack to connect a pair

of headphones.

UNBALANCED [L/MONO] and [R] OUTPUT

jacks (page 16)

Use these two standard 1/4" mono audio jacks together to

output unbalanced stereo signals. Alternatively, if mono

output is required, only the [L/MONO] jack should be

connected.

BALANCED [L] and [R] OUTPUT jacks

(page 16)

Use these two XLR-type jacks together to output

balanced audio signals.

[AUX IN] jack (page 45)

Use this Auxiliary Input stereo mini-jack to connect other

audio equipment so that its output can be mixed with that

of the stage piano.

NOTE To balance the volumes of the stage piano and the

connected audio equipment, adjust the output volume of

the latter.

[TO HOST] USB terminal (page 44)

Use this terminal to connect your stage piano to the USB

terminal of a computer using a USB cable.

[TO DEVICE] USB terminal (page 39)

Use this terminal to connect a USB flash-memory device

to your stage piano.

[IN] and [OUT] MIDI terminals (page 45)

Use these two MIDI terminals to link up your stage piano

with other MIDI devices.

[SUSTAIN] FOOT SWITCH jack (page 17)

Use this jack to connect an FC3A Foot Switch (provided)

or an optional FC4A or FC5 Foot Switch for use as a

dedicated sustain pedal.

[ASSIGNABLE] FOOT SWITCH jack (page 17)

Use this jack to connect an optional FC4A or FC5 Foot

Switch in order to perform a range of freely assignable

functions.

FOOT CONTROLLER jack(s) (page 17)

The CP4 STAGE features two foot controller jacks, labeled

[1] and [2]; the CP40 STAGE has one. They can be used

to connect an optional FC7 Foot Controller in order to

perform a range of freely assignable functions.

Air vent

This vent prevents the instrument from overheating.

CP4 STAGE only

CP40 STAGE only

CP4 STAGE only

CP4 STAGE/CP40 STAGE Owner’s Manual 15

Setting Up

Power Supply

CP4 STAGE

Ensure that the [ ] (Power) switch on the

rear panel is set to the Off ( ) position.

2 Insert the appliance end of the bundled

power cord (see below) into the [AC IN] jack,

also on the rear panel.

3 Plug the other end of the power cord into a

domestic-use, AC wall outlet.

NOTE Carry out this procedure in reverse order when

disconnecting the power cord.

WARNING

Use only the AC power cord supplied with your stage piano.

The use of an inappropriate replacement can lead to

overheating or electric shock.

WARNING

The power cord supplied with your stage piano must not be

used with other electrical equipment. Failure to observe this

precaution can result in the equipment being damaged or

lead to the outbreak of fire.

WARNING

Make sure your CP4 STAGE meets the voltage requirement

for the country or region in which it is being used. The power

cord includes a grounding pin to prevent electrical shock

and damage to the equipment. When connecting to an outlet,

connect the adaptor’s ground lead to the ground screw. If

you are unsure how to make this connection, contact your

Yamaha dealer or service center.

CAUTION

The stage piano remains charged and draws a small amount

of power even when the [] (Power) switch is set to the Off

position. If it will not be used for an extended period of time,

therefore, be sure to unplug the power cord from the wall

outlet.

CP40 STAGE

Ensure that the [ ] (Standby/On) switch on

the rear panel is set to the Standby ( )

position.

2 Connect the DC power cord from the bundled

power adaptor (see below) to the DC IN jack

on the rear panel.

3 Plug the adaptor’s AC power cord into a

domestic-use, AC wall outlet.

NOTE Carry out this procedure in reverse order when

disconnecting the power adaptor.

WARNING

Be sure to use only the power adaptor supplied with your

stage piano. Use of a different adaptor is inherently

dangerous and may result in equipment damage,

overheating, or the outbreak of fire.

WARNING

Make sure your CP40 STAGE meets the voltage requirement

for the country or region in which it is being used.

CAUTION

The stage piano remains charged and draws a small amount

of power even when the [] (Standby/On) switch is set to the

Standby position. If it will not be used for an extended period

of time, therefore, be sure to unplug the power adaptor from

the wall outlet.

[ ] switch

[AC IN] jack

DC IN jack

16 CP4 STAGE/CP40 STAGE Owner’s Manual

Setting Up

Connecting Audio

Equipment

Your stage piano does not come with built-in speakers. In

order to hear what you play, therefore, you will need to

connect it to other audio equipment such as amplifiers

and speakers. You can also plug a set of headphones

into the [PHONES] jack in order to monitor the sound

directly. Audio equipment can be connected in a number

of different ways, two of which are described below.

Based on the illustrations, choose the connection format

most suited to your setup.

CAUTION

To prevent hearing loss, avoid using headphones at high

volumes for extended periods of time.

NOTICE

Whenever connecting other audio equipment, ensure that all

devices are turned off.

Output via amplifiers or powered

speakers

Using a pair of keyboard amplifiers or powered speakers,

you can accurately reproduce the full richness of your

stage piano’s Performances (page 21) and effects,

including stereo panning. In this type of situation,

connections to the amplifiers or speakers should be

made via the UNBALANCED [L/MONO] and [R] OUTPUT

jacks on the rear panel. If you would prefer to monitor

your playing using a single keyboard amplifier or

powered speaker, the UNBALANCED [L/MONO]

OUTPUT jack should be used.

Output via a mixer

It is commonplace for musical instruments to be

connected to a mixer in recording and live-performance

environments. In addition to the unbalanced jacks

mentioned above, the CP4 STAGE also features a pair of

professional-use, balanced XLR jacks that prevent

unwanted noise from entering output signals. When

connecting to a mixer, we recommend that these

BALANCED [L] and [R] OUTPUT jacks be used. (As the

CP40 STAGE does not feature balanced output jacks, its

UNBALANCED [L/MONO] and [R] OUTPUT jacks should

be used in this type of situation.)

NOTE The sound output via the headphones is identical to that

output via the UNBALANCED [L/MONO] and [R] OUTPUT

jacks and the BALANCED [L] and [R] OUTPUT jacks.

Furthermore, plugging in or disconnecting a set of

headphones has no effect on the sound being output via

these jacks.

Left keyboard amplifier Right keyboard amplifier

[L/MONO] and [R] OUTPUT jacks

[PHONES] jack

OUTPUT R

OUTPUT L

[L] and [R]

OUTPUT jacks

[PHONES] jack

Amplifier

Left

speaker

Right

speaker

Mixer

CP4 STAGE/CP40 STAGE Owner’s Manual 17

Setting Up

Connecting Pedals

Two different types of pedal can be used with your stage

piano — foot switches, such as the bundled FC3A and

the optional FC4A and FC5, and a foot controller like the

optional FC7. Both are connected via the rear panel,

although the jacks used and the corresponding functions

differ as described below.

Foot switches

The FC3A Foot Switch that comes with your stage piano

is connected via the [SUSTAIN] FOOT SWITCH jack. It

functions in the same way as the damper pedal of an

acoustic piano, allowing notes played while it is operated

to sustain for longer than normal after you release the

corresponding keys.

The FC3A can also function as a half-damper pedal, and

in such a case, the damper effect will depend on the

degree to which the pedal is operated. You can activate

the half-damper playing technique as follows:

Press [UTILITY]; select 03: Controller using [ ] and [ ]

and press [ENTER]; set Sustain to “FC3 Half On” using

[-1/NO] and [+1/YES]; press [EXIT] several times to

return to the Performance screen (page 22).

An optional FC4A or FC5 Foot Switch can be connected

via the [ASSIGNABLE] FOOT SWITCH jack so that

various functions can be assigned to it. This allows you to

control the assigned parameter by foot.

NOTE Refer to the Reference Manual (pdf) for details on how to

assign a parameter to an FC4A or FC5 Foot Switch.

Foot controllers

Used to control an assigned parameter, an FC7 Foot

Controller (sold separately) is connected via the [1] and

[2] FOOT CONTROLLER jacks on the CP4 STAGE or via

the [FOOT CONTROLLER] jack on the CP40 STAGE. This

allows you to control assigned parameter(s) such as Part

volume(s) by foot.

NOTE Refer to the Reference Manual (pdf) for details on how to

assign a parameter to an FC7 Foot Controller.

Turning On and Off the

Stage Piano

Turning on

Ensure that your stage piano’s [MASTER

VOLUME] dial and the volumes of any

connected keyboard amplifiers or powered

speakers are turned fully down (i.e., to MIN or

0).

2 Set the [ ] switch on the rear panel to the

On ( ) position.

3 Turn on the keyboard amplifiers or powered

speakers.

Turning off

Ensure that the volumes of your stage piano

and any connected keyboard amplifiers or

powered speakers are turned fully down (i.e.,

to MIN or 0).

2 Turn off the keyboard amplifiers or powered

speakers.

3 On the CP4 STAGE, set the [] switch on the

rear panel to the Off () position; on the

CP40 STAGE, set it to the Standby ( )

position.

CP4 STAGE

CP40 STAGE

18 CP4 STAGE/CP40 STAGE Owner’s Manual

Setting Up

Auto Power-Off

The Auto Power-Off function automatically turns off your

stage piano after a certain period of inactivity, which is

approximately 30 minutes by default.

If you would like to disable this function, turn off the stage

piano once and then turn it back on while holding down

the leftmost key on the keyboard. The message “Auto

power off disabled” will be displayed on-screen, and this

function will remain disabled until you set a new Auto

Power-Off time.

If necessary, use the following procedure to set the time

until the Auto Power-Off function turns off the stage piano.

Press [UTILITY]; select 01: General using [ ] and press

[ENTER]; select AutoOff using [ ]; set the desired time

using [-1/NO] and [+1/YES] or the Data Dial; press

[STORE].

NOTICE

• The stage piano remains charged and draws a small

amount of power even when turned off by the Auto Power-

Off function. To shut it down completely, therefore, unplug

it from the wall outlet.

• In certain modes of operation such as when data has been

edited, the Auto Power-Off function may not turn off the

stage piano when the set period of inactivity has elapsed.

We recommend, therefore, that you always turn off the

instrument manually when you are finished using it.

• If your stage piano is connected to other equipment such

as amplifiers, speakers, or a computer, but you do not

intend to use it for some time, we recommend that you

turn off all devices as described in their owner’s manuals.

Doing so eliminates the risk of damage to the other

equipment. If you do not want the stage piano to turn off

automatically when connected to other equipment, disable

the Auto Power-Off function.

• Any unsaved data will be lost when the Auto Power-Off

function turns off the stage piano. Be sure, therefore, to

store your work before it does so.

• If the stage piano’s AutoOff parameter is set to “off”, that

setting will be retained when you import system data that

was saved externally, regardless of the Auto Power-Off

setting contained in that data. If, however, a specific Auto

Power-Off time has been set using the AutoOff parameter

and system data is imported, the Auto Power-Off setting

contained in that data will be applied.

• It should be noted that executing the Factory Set function

(page 43) will cause the Auto Power-Off time to revert to

the default setting of 30 minutes.

NOTE

• Settings for the Auto Power-Off function do not represent exact

times and there may be some variation.

• When the Auto Power-Off function has turned off the instrument,

you will first need to return the [ ] switch to the Off () position in

the case of the CP4 STAGE or the Standby () position in the

case of the CP40 STAGE before turning it back on.

Adjusting Volume and LCD

Contrast

While playing your stage piano, you can adjust the output

volume either on the instrument itself or via your keyboard

amplifiers or powered speakers. The stage piano’s

volume is adjusted using the [MASTER VOLUME] dial.

Set the instrument’s volume to close to 70% of the

maximum, and then raise the volume on the keyboard

amplifiers or powered speakers by an appropriate

amount.

NOTE The stage piano’s [MASTER VOLUME] dial cannot be used

to adjust the volume of audio being input via the [AUX IN]

jack (page 45).

CAUTION

To prevent hearing loss, avoid using headphones at high

volumes for extended periods of time.

If you find it difficult to read the on-screen text, you can

adjust the LCD contrast using the [-1/NO] and [+1/YES]

buttons with the [UTILITY] button held down.

NOTE The Contrast parameter on the General screen from the

Utility area can also be used to adjust the LCD contrast as

described above. Refer to the Reference Manual (pdf) for

details.

70%

LoudestQuietest

CP4 STAGE/CP40 STAGE Owner’s Manual 19

Basic Operations & Display Content

Cursor Types & Operations

The following two types of cursor are used on-screen to

highlight the current selection:

 Arrow cursor

The arrow cursor ( ) flashes to the left of the currently

selected item. You can move this cursor up, down, left,

and right, depending on the current screen, using the

[ ], [ ], [], and [ ] buttons.

 Flashing cursor

On naming screens, the currently selected character will

itself flash on and off. You can move this cursor to the left

and right only using the [] and [ ] buttons.

[ ], [ ], [], and [ ] buttons

The [ ], [ ], [], and [ ] buttons can be used to move

the cursor in the corresponding direction on-screen. The

[ ] and [ ] buttons can also be used to display menu

items and to move between panes on screens containing

more than one.

Changing & Setting Values

Data Dial

The Data Dial can be turned clockwise to increase values

and vice-versa. In addition, when adjusting parameters

with a wide range of possible settings, you can turn the

Data Dial with the [SHIFT] button held down to increase

or decrease in units of 10.

[-1/NO] and [+1/YES] buttons

The [+1/YES] button increases the current setting by one

each time it is pressed; the [-1/NO] button decreases it. If

you hold down either button, the setting will change

continuously. In addition, when adjusting parameters with

a wide range of possible settings, you can press these

buttons with the [SHIFT] button held down to increase or

decrease accordingly in units of 10.

Increase

setting

Decrease

setting

Decrease setting

by one

Increase setting

by one

20 CP4 STAGE/CP40 STAGE Owner’s Manual

Basic Operations & Display Content

Displaying Menus &

Making Selections

Certain editing areas contain a number of different

screens that can be selected from a menu as follows.

Use the [ ] and [ ] buttons to change the currently

displayed menu item, and press the [ENTER] button to

make a selection. The up and down More symbols (

and ) shown to the left of the menu item number

indicate that the menu contains more items above and/or

below the one displayed.

Changing Panes

Certain editing screens are split over a number of

different panes. In such a case, up and down More

symbols ( and ) will be shown at the bottom-right of

the screen. You can use the [ ] and [ ] buttons in such

a situation to move between panes.

Entering Text

When editing parameters supporting text input, such as

the name of a Performance, first use the [ ] and [ ]

buttons to move the flashing cursor to the character you

wish to change. You can then change the character at

that position using the [-1/NO] and [+1/YES] buttons or

the Data Dial.

Exiting from the Current

Screen

You can press the [EXIT] button to move one step back in

the stage piano’s menu structure. Pressing the [EXIT]

button several times will return you to the Performance

screen — that is, the first one displayed when the

instrument is turned on.

Menu item

number

Screen name

More menu items below

More menu items above

and below

More menu items above

Editable parameters

More symbol indicating additional pane(s)

Flashing cursor shows selected character

Pagina se încarcă ...

Yamaha CP4 Stage Manualul proprietarului

Marca: Yamaha

Model: CP4 Stage

Categorie: Echipamente muzicale

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha CP4 Stage El kitabı
français: Yamaha CP4 Stage Le manuel du propriétaire
čeština: Yamaha CP4 Stage Návod k obsluze
русский: Yamaha CP4 Stage Инструкция по применению
English: Yamaha CP4 Stage Owner's manual
suomi: Yamaha CP4 Stage Omistajan opas
polski: Yamaha CP4 Stage Instrukcja obsługi
Deutsch: Yamaha CP4 Stage Bedienungsanleitung
italiano: Yamaha CP4 Stage Manuale del proprietario
español: Yamaha CP4 Stage El manual del propietario
svenska: Yamaha CP4 Stage Bruksanvisning
dansk: Yamaha CP4 Stage Brugervejledning
português: Yamaha CP4 Stage Manual do proprietário
Nederlands: Yamaha CP4 Stage de handleiding

Lucrări conexe

Alte documente

Hikoki BL36200 Manual de utilizare