Philips S9111/41 Manual de utilizare

S91xx/S90xx

1

S91XX, S90XX

ENGLISH 4

БЪЛГАРСКИ 25

ČEŠTINA 47

EESTI 68

HRVATSKI 89

MAGYAR 110

ҚАЗАҚША 131

LIETUVIŠKAI 152

LATVIEŠU 174

POLSKI 195

ROMÂNĂ 216

РУССКИЙ 237

SLOVENSKY 260

SLOVENŠČINA 281

SRPSKI 302

УКРАЇНСЬКА 323

4

Introduction

Congratulations on your purchase and welcome to Philips!

To fully benet from the support that Philips offers, register your

product at www.philips.com/welcome.

Please read this user manual, as it contains information about the features of

this shaver as well as some tips to make shaving easier and more enjoyable.

General description (Fig. 1)

1 Comb for beard styler attachment

2 Click-on beard styler attachment

3 Click-on trimmer attachment

4 Click-on shaving unit

5 On/off button

6 Socket for small plug

7 Exclamation mark

8 Replacement reminder

9 Battery charge indicator

10 Travel lock symbol

11 Cleaning reminder

12 Replacement symbol

13 SmartClean system

14 Cap of SmartClean system

15 On/off button

16 Cleaning symbol

17 Drying symbol

18 Ready symbol

19 Charge symbol

20 Cleaning cartridge for SmartClean system

21 Adapter

22 Small plug

23 Retaining ring holder

24 Pouch

Note: The accessories supplied may vary for different products. The box shows

the accessories that have been supplied with your appliance.

Important

Read this user manual carefully before you use the shaver and

the SmartClean system. Save this user manual for future reference.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut off the adapter to

replace it with another plug, as this causes a hazardous situation.

- The shaver and the SmartClean system are not intended for use

by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of these

appliances by a person responsible for their safety.

ENGLISH

- Children should be supervised to ensure that they do not play with

the shaver and the SmartClean system.

- Always unplug the shaver before you clean it under the tap.

Caution

- Never immerse the SmartClean system in water nor rinse it under

the tap.

- Never use water hotter than 80°C to rinse the shaver.

- Do not use the shaver, SmartClean system, adapter or any other part

if it is damaged, as this may cause injury. Always replace a damaged

adapter or part with one of the original type.

- Only use the SmartClean system with the original cleaning cartridge.

- Always place the SmartClean system on a stable, level and horizontal

surface to prevent leakage.

- Always make sure that the cartridge compartment is closed before you

use the SmartClean system to clean or charge the shaver.

- When the SmartClean system is ready for use, do not move it to

prevent leakage of cleaning uid.

- The SmartClean system thoroughly cleans but does not disinfect your

shaver, therefore do not share the shaver with others.

- Never use compressed air, scouring pads, abrasive cleaning agents or

aggressive liquids such as petrol or acetone to clean the appliance.

- Water may leak from the socket at the bottom of the shaver when you

rinse it. This is normal and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

Compliance with standards

- This shaver is waterproof and complies with the internationally

approved safety regulations. It is suitable for use in the bath or shower

and for cleaning under the tap. For safety reasons, the shaver can

therefore only be used cordlessly.

- The shaver and the SmartClean system comply with all applicable

standards and regulations regarding exposure to electromagnetic elds.

General

- The adapter is equipped with an automatic voltage selector and is

suitable for mains voltages ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of less

than 24 volts.

- Maximum noise level: Lc = 69dB(A)

The display

Note: Before you use the shaver for the rst time, remove the protective foil

from the display.

- S91XX/SH90XX

ENGLISH 5

Charging

- Charging takes approx. 1 hour.

Note: This appliance can only be used cordlessly.

- Quick charge: When you connect the appliance to the mains,

it produces a sound. Then the lights of the battery charge indicator light

up one after the other continuously. When the shaver contains enough

energy for one shave, the bottom light of the battery charge indicator

starts to ash slowly.

- If you leave the appliance connected to the mains, the charging process

continues. To indicate that the appliance is charging, rst the bottom

light ashes white and then lights up white continuously. Then the

second light ashes and then lights up continuously, and so on until the

shaver is fully charged.

Battery fully charged

Note: This appliance can only be used cordlessly.

Note: When the battery is full, the display switches off automatically after

30 minutes. When you press the on/off button during or after charging,

you hear a sound to indicate that the shaver is still connected to the mains.

- When the battery is fully charged, all lights of the battery charge

indicator light up white continuously.

Battery low

- When the battery is almost empty, the bottom light ashes orange and

you hear a sound.

Remaining battery capacity

- The remaining battery capacity is indicated by the lights of the battery

charge indicator that light up continuously.

ENGLISH6

Cleaning reminder

For optimal shaving performance, we advise you to clean the shaver after

every use.

- When you switch off the shaver, the cleaning reminder ashes to

remind you to clean the shaver.

Travel lock

You can lock the shaver when you are going to travel. The travel lock

prevents the shaver from being switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter the travel lock mode.

, While you activate the travel lock, the travel lock symbol lights up

white continuously. When the travel lock is activated, the shaver

produces a sound and the travel lock symbol ashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The travel lock symbol ashes and then lights up continuously.

The shaver is now ready for use again.

Note: You can also deactivate the travel lock by connecting the appliance to

the mains.

ENGLISH 7

Replacing shaving heads

For maximum shaving performance, we advise you to replace the shaving

heads every two years.

- The appliance is equipped with a replacement reminder which reminds

you to replace the shaving heads. The replacement reminder lights up

white continuously and the arrows ash white. You hear a beep to

indicate you have to replace the shaving heads.

Note: After replacing the shaving heads, you need to reset the shaver by

pressing the on/off button for 7 seconds.

Exclamation mark

Blocked shaving heads

- If the shaving heads are blocked, the exclamation mark lights up orange

continuously. The replacement reminder and the cleaning reminder

ash white alternately and you hear a sound. In this case, the motor

cannot run because the shaving heads are soiled or damaged.

- When this happens, you have to clean the shaving heads or replace

them.

Overheating

- If the appliance overheats during charging, the exclamation mark ashes

orange.

- When this happens, the shaver automatically switches off. Charging

continues once the appliance is back to the normal temperature.

Charging

Charging takes approx. 1 hour.

A fully charged shaver has a shaving time of up to 50 minutes.

Note: You cannot use the appliance while charging.

Charge the shaver before you use it for the rst time and when the display

indicates that the battery is almost empty .

Charging with the adapter

1 Make sure the appliance is switched off.

2 Insert the small plug into the appliance (1) and put the adapter in the

wall socket (2).

ENGLISH8

Charging in the SmartClean system (specic types only)

1 Put the small plug in the SmartClean system.

2 Put the adapter in the wall socket.

3 Press the top cap to be able to place the shaver in the holder

(‘click’).

4 Hold the shaver upside down above the holder. Make sure the front

of the shaver points towards the SmartClean system.

5 Place the shaver in the holder (1), tilt the shaver backwards (2) and

press down the top cap to connect the shaver (‘click’) (3).

Note: The battery symbol ashes slowly to indicate the appliance is charging.

Using the shaver

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you expect and your skin

may even become slightly irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times a week) with this shaver

for a period of 3 weeks to allow your skin to adapt to the new shaver.

Tip: To ensure the best result, we advise you to pre-trim your beard if you have

not shaved for 3 days or longer.

Note: This appliance can only be used cordlessly.

1 Press the on/off button once to switch on the shaver.

, The display lights up for a few seconds.

ENGLISH 9

2 Move the shaving heads over your skin in circular movements.

- Do not make straight movements.

3 Press the on/off button once to switch off the shaver.

, The display lights up for a few seconds and then shows the remaining

battery charge.

Wet shaving

You can also use this shaver on a wet face with shaving foam or shaving gel.

To shave with shaving foam or shaving gel, follow the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure that the shaving unit

glides smoothly over your skin.

4 Press the on/off button once to switch on the shaver.

5 Move the shaving heads over your skin in circular movements.

Note: Rinse the shaver under the tap regularly to ensure that it continues to

glide smoothly over your skin.

6 Dry your face and thoroughly clean the shaver after use (see chapter

‘Cleaning and maintenance’).

Note: Make sure you rinse all foam or shaving gel off the shaver.

ENGLISH10

Using the click-on attachments

Note: The accessories supplied may vary for different products. The box shows

the accessories that have been supplied with your appliance.

Using the trimmer attachment

You can use the trimmer attachment to groom your sideburns and

moustache.

1 Pull the shaving unit straight off the appliance.

Note: Do not twist the shaving unit while you pull it off the appliance.

2 Insert the lug of the trimmer attachment into the slot in the top of

the shaver. Then press down the trimmer attachment to attach it to

the appliance (‘click’).

3 Press the on/off button once to switch on the appliance.

, The display lights up for a few seconds.

4 You can now start trimming.

5 Press the on/off button once to switch off the appliance.

, The display lights up for a few seconds to show the remaining

battery charge.

6 Pull the trimmer attachment straight off the appliance.

Note: Do not twist the trimmer attachment while you pull it off the appliance.

7 Insert the lug of the shaving unit into the slot in the top of the

appliance. Then press down the shaving unit to attach it to the

appliance (‘click’).

Using the beard styler attachment

1 Make sure the appliance is switched off.

2 Pull the shaving unit straight off the appliance.

Note: Do not twist the shaving unit while you pull it off the appliance.

ENGLISH 11

3 Insert the lug of the beard styler attachment into the slot in the top

of the appliance. Then press down the beard styler attachment to

attach it to the appliance (‘click’).

Using the beard styler attachment with comb

You can use the beard styler attachment with the comb attached to style

your beard at one xed setting, but also at different length settings. The hair

length settings on the beard styler attachment correspond to the remaining

hair length after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding grooves on both sides of the

beard styler attachment (‘click’).

2 Press the length selector and then push it to the left or right to

select the desired hair length setting.

3 Press the on/off button once to switch on the appliance.

4 You can now start styling your beard.

Using the beard styler attachment without comb

You can use the beard styler attachment without the comb to contour

your beard, moustache, sideburns or neckline.

1 Pull the comb off the beard styler attachment.

Note: Grab the comb in the centre to pull it off the beard styler attachment.

Do not pull at the sides of the comb.

2 Press the on/off button once to switch on the appliance.

ENGLISH12

3 You can now start contouring your beard, moustache, sideburns or

neckline.

Cleaning and maintenance

Cleaning the shaver in the SmartClean system

Note: The accessories supplied may vary for different products. The box shows

the accessories that have been supplied with your appliance.

The SmartClean system comes in two types. The features available on your

SmartClean system may differ per type:

- SmartClean system Basic has one phase: the rinsing phase.

- SmartClean system Plus has two phases: the rinsing phase and the

drying phase.

Preparing the SmartClean system for use

Do not tilt the SmartClean to prevent leakage.

Note: Hold the SmartClean while you prepare it for use.

1 Put the small plug in the back of the SmartClean system.

2 Put the adapter in the wall socket.

3 Press the button on the side of the SmartClean system (1) and lift

the top part of the SmartClean system (2).

ENGLISH 13

4 Pull the seal off the cleaning cartridge.

5 Place the cleaning cartridge in the SmartClean system.

6 Push the top part of the SmartClean system back down (‘click’).

Using the SmartClean system

Always make sure to shake excess water off the shaver before you place

it in the SmartClean.

1 Press the top cap to be able to place the shaver in the holder

(‘click’).

ENGLISH14

2 Hold the shaver upside down above the holder. Make sure the front

of the shaver points towards the SmartClean system.

3 Place the shaver in the holder (1), tilt the shaver backwards (2)

and press down the top cap to connect the shaver (‘click’) (3).

, The battery symbol starts to ash, which indicates that the shaver

is charging.

4 Press the on/off button on the SmartClean system to start the

cleaning program.

, During the rinsing phase, the rinsing symbol will ash.

Note: The rinsing phase takes approx. 10 minutes.

, SmartClean systems Plus only:

During the drying phase, the drying symbol will ash.

Note: The drying phase takes approx. 4 hours.

, When the cleaning program has been completed, the ready symbol

lights up continuously.

, The battery symbol lights up continuously to indicate that the shaver

is fully charged.

Note: Charging takes approx. 1 hour.

Note: If you press the on/off button of the SmartClean system during the cleaning

program, the program aborts. In this case, the rinsing or drying symbol stops ashing.

Note: If you remove the adapter from the wall socket during the cleaning

program, the program aborts.

Note: 30 minutes after the cleaning program and charging have been

completed, the SmartClean switches off automatically.

ENGLISH 15

Replacing the cartridge of the SmartClean System

- Replace the cleaning cartridge when the replacement symbol ashes

orange or when you are no longer satised with the result.

1 Press the button on the side of the SmartClean system (1) and lift

the top part of the SmartClean system (2).

2 Take the empty cleaning cartridge from the SmartClean system and

pour any remaining cleaning uid out of the cleaning cartridge.

You can simply pour the cleaning uid down the sink.

3 Throw away the empty cleaning cartridge.

4 Unpack the new cleaning cartridge and pull the seal off the cartridge.

5 Place the new cleaning cartridge in the SmartClean system.

6 Push the top part of the SmartClean system back down (‘click’).

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal shaving performance.

Be careful with hot water. Always check if the water is not too hot,

to prevent your hands from getting burnt.

Never dry the shaving unit with a towel or tissue, as this may damage the

shaving heads.

ENGLISH16

1 Rinse the shaving unit under a warm tap for some time.

2 Pull the shaving head holder off the bottom part of the shaving unit.

3 Rinse the shaving head holder under a warm tap.

4 Carefully shake off excess water and let the shaving head holder dry.

5 Reattach the shaving head holder to the bottom part of the shaving

unit (‘click’).

Thorough cleaning method

Make sure the appliance is switched off.

1 Pull the shaving head holder off the bottom part of the shaving unit.

2 Place the retaining ring holder on the retaining ring (1), turn it

anticlockwise (2) and lift it off the shaving head (3).

Remove the retaining ring from the retaining ring holder and repeat this

process for the other retaining rings.

ENGLISH 17

3 Remove the shaving heads from the shaving head holder. Each shaving

head consists of a cutter and guard.

Note: Do not clean more than one cutter and guard at a time, since they are

all matching sets. If you accidentally put a cutter in the wrong shaving guard,

it may take several weeks before optimal shaving performance is restored.

4 Clean the cutter and guard under the tap.

5 After cleaning, place the cutter back into the guard.

6 Put the shaving heads back into the shaving head holder.

Note: Make sure the notches on both sides of the shaving heads t exactly

onto the projections in the shaving-head holder.

7 Place the retaining ring holder on the retaining ring (1), place it

on the shaving head (2) and turn it clockwise (3) to reattach the

retaining ring.

Repeat this process for the other retaining rings.

ENGLISH18

Note: Hold the shaving head holder in your hand when you reinsert the

shaving heads and reattach the retaining rings. Do not place the shaving head

holder on a surface when you do this, as this may cause damage.

8 Reattach the shaving head holder to the bottom part of the

shaving unit.

Cleaning the click-on attachments

Cleaning the trimmer attachment

Clean the trimmer attachment every time you have used it.

1 Switch on the appliance with the trimmer attachment attached.

2 Rinse the trimmer attachment under a hot tap for some time.

3 Carefully shake off excess water and let the trimmer attachment dry.

4 After cleaning, switch off the appliance.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop

of sewing machine oil every six months.

Cleaning the beard styler attachment

Clean the beard styler attachment every time you have used it.

1 Pull the comb off the beard styler attachment.

2 Rinse the beard styler attachment and the comb separately under a

hot tap for some time.

3 Carefully shake off excess water and let the beard styler

attachment and comb dry.

4 Lubricate the teeth with a drop of sewing machine oil every

six months.

Storage

1 Store the shaver in the pouch supplied.

Note: We advise you to let the shaver dry before you store it in the pouch.

ENGLISH 19

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise you to replace the shaving

heads every two years.

Replacement reminder

The shaving unit symbol lights up to indicate that the shaving heads need to

be replaced. Replace damaged shaving heads right away.

Only replace the shaving heads with original SH90 Philips shaving heads.

1 The shaving unit symbol lights up continuously, the arrows ash

white and you hear a beep when you switch off the shaver .

2 Pull the shaving head holder off the bottom part of the shaving unit.

3 Place the retaining ring holder on the retaining ring (1), turn it

anticlockwise (2) and lift it off the shaving head (3).

Remove the retaining ring from the retaining ring holder and repeat this

process for the other retaining rings.

4 Remove the shavings heads from the shaving head holder and throw

them away.

5 Place new shaving heads in the holder.

Note: Make sure the notches on both sides of the shaving heads t exactly

onto the projections in the shaving-head holder.

ENGLISH20

Pagina se încarcă ...

Philips S9111/41 Manual de utilizare

Acest manual este potrivit și pentru

Philips S9111/41 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente