Simplicity BLIZZARD SNOW SERIES Manual de utilizare

Marca: Simplicity

Model: BLIZZARD SNOW SERIES

Categorie: Accesorii pentru autovehicule

Tip: Manual de utilizare

Acest manual este potrivit și pentru

12Z314-0110-E1

English

bg cs hr slet hu

Èeština

lt lv pl ro ru

eesti keel Hrvatski Latviešu Polski Ðóññêèé

Românã

Áúëãàðñêè LietuviųMagyar Slovenšèina

Operator’s Manual

Èíñòðóêöèè çà åêñïëîàòàöèÿ

Návod k obsluze

Kasutusjuhend

Priruènik za operatora

Kezelési útmutató

Naudojimo instrukcija

Operatora rokasgrāmata

Instrukcja obs³ugi

Manual de utilizare

Ðóêîâîäñòâî ïî ýêñïëóàòàöèè

Priroènik za uporabo

Form No. 277615EST

Revision: B

E 2009 Briggs & Stratton Corporation,

Briggs & Stratton is a registered trademark

of Briggs & Stratton Corporation

Model 120000

150000

200000

210000

Snow Seriest

Snow Series MAXt

Not for Reproduction

BRIGGSandSTRATTON.COM

Not for Reproduction

7 8

Not for Reproduction

4 BRIGGSandSTRATTON.COM

General Information

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on your

engine (see the Features and Controls page).

Date of purchase:

Engine model:

MM/DD/YYYY

Model: Code:Ty pe:

Engine Power Rating Information

The gross power rating for individual gas engine models is labeled in accordance with

SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been obtained and corrected in

accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060

RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be

lower and is affected by, among other things, ambient operating conditions and

engine-to-engine variability. Given both the wide array of products on which engines are

placed and the variety of environmental issues applicable to operating the equipment,

the gas engine will not develop the rated gross power when used in a given piece of

power equipment (actual “on-site” or net power). This difference is due to a variety of

factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling,

carburetor, fuel pump, etc.), application limitations, ambient operating conditions

(temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing

and capacity limitations, Briggs & Stratton may substitute an engine of higher rated

power for this Series engine.

Operator Safety

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

Fuel Shutoff

Read Manual

Choke

Oil

Fuel

On Off

Stop

Wear Eye

Protection

Slow

Fast

SAFETY AND CONTROL SYMBOLS

Hazardous

Chemical

Frostbite

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING

Certain components in this product and its related accessories contain chemicals

known to the State of California to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling.

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Briggs & Stratton does not approve or authorize the use of these engines on 3-wheel

All Terrain Vehicles (ATVs), motor bikes, fun/recreational go -karts, aircraft products,

or vehicles intended for use in competitive events. Use of these engines in such

applications could result in property damage, serious injury (including paralysis), or

even death.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

WARNING

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes before removing t he fuel

cap.

• Fill fuel tank outdoors or in well -ventilated area.

• Do not overfill fuel tank. To allow for expansion of the gasoline, do not fill above

the bottom of the fuel tank neck.

• Keep gasoline away f rom sparks, open flames, pilot lights, heat, and other

ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

• If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

When Operating Equipment

• Do not tip engine or equipment at angle which causes gasoline to spill.

• Do not choke the carburetor to stop engine.

• Never start or run t he engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel tank must be empty or f uel

can leak out and result in a fire or explosion.

When Transporting Equipment

• Transport with fuel tank EMPTY or with fuel shut-off valve OFF.

When Storing Gasoline Or Equipment With Fuel In Tank

• Store away from furnaces, stoves, water heaters or other appliances that have

pilot light or other ignition source because they can ignite gasoline vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

Engines give off carbon monoxide, an odorless, colorless, poison gas .

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

Not for Reproduction

Rapid r etraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

• When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly t o avoid kickback.

• Remove all external equipment/engine loads before starting engine.

• Direct-coupled equipment components such as, but not limited to, blades,

impellers, pulleys, sprockets, etc., must be securely attached.

Rotating parts can contact or entangle hands, feet, hair, clothing, or

accessories.

Traumatic amputation or severe laceration can result.

WARNING

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

• It is a violation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest -covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only c orrect tools.

• Do not tamper with governor spring, links or other parts to increase engine

speed.

• Replacement parts must be the s ame and installed in the same position as the

original parts.

• Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Not for Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Compare the illustration

with your engine to familiarize yourself with the location of

various features and controls.

A. Engine Identification

Model Type Code

B. Spark Plug

C. Choke

D. Primer

E. Fuel Shut-off Valve

F. Starter Cord Handle

G. Finger Guard

H. Stop Switch (optional) *

I. Fuel Tank and Cap

J. Oil Fill Cap

K. Dipstick/Oil Fill

L. Oil Drain Plug

M. Muffler

Muffler Guard (optional)

Muffler Deflector

N. Safety Key

O. Push Button Electric Start

P. Snow Hood

Q. Power Cord Receptacle

R. Electric Starter

S. Throttle Control (optional) *

* Some engines and equipment have r emote controls. See the equipment manual for

location and operation of remote controls.

Operation

Oil capacity (see the Specifications section)

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to

select the best v iscosity for the outdoor temperature range expected.

SAE 30

10W-30

Synthetic 5W-30

5W-30

°F °C

* Below 40°F(4°C) the use of SAE 30 will result in hard starting.

** Above 80°F(27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

How To Check/Add Oil - Figure

2 3

Before adding or checking the oil

• Place engine level.

• Clean the oil fill area of any debris.

Models with oil fill cap (Figure 2)

1. Remove the oil fill cap (A).

2. To add oil, pour the oil slowly into the engine oil fill (B). Fill to point of overflowing.

3. Replace and tighten the oil fill cap.

Models with extended dipstick (Figure 3)

1. Remove the dipstick (C) and wipe with a clean cloth.

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be at the top of the full indicator

(D) on the dipstick.

4. To add oil, pour the oil slowly into the engine oil fill (B). Do not overfill. After adding

oil, wait one minute and then recheck the oil level.

5. Replace and tighten the dipstick.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) o r up to 15% MTBE (methyl tertiary

butyl ether) is acceptable.

NOTICE: Do not use unapproved gasolines, such as E85. Do not mix oil in gasoline or

modify the engine to run on alternate fuels. This will damage the engine components and

void the engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See

Storage. All fuel is not the same. If starting or performance problems occur, change fuel

providers or change brands. This engine is certified to operate on gasoline. The

emissions control system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is acceptable. To remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions. See a Briggs & Stratton

Authorized Dealer for high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

How To Add Fuel - Figure

WARNING

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes before removing t he fuel

cap.

• Fill fuel tank outdoors or in well -ventilated area.

• Do not overfill fuel tank. To allow for expansion of the gasoline, do not fill above

the bottom of the fuel tank neck.

• Keep gasoline away f rom sparks, open flames, pilot lights, heat, and other

ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

• If fuel spills, wait until it evaporates before starting engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap (A) (Figure 4).

2. Fill the fuel tank (B) with gasoline. To allow f or expansion of the gasoline, do not fill

above the bottom of the fuel tank neck (C).

3. Reinstall the fuel cap.

How To Start The Engine - Figure

5 6 7

Rapid r etraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

• When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly t o avoid kickback.

• Remove all external equipment/engine loads before starting engine.

• Direct-coupled equipment components such as, but not limited to, blades,

impellers, pulleys, sprockets, etc., must be securely attached.

WARNING

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

Not for Reproduction

Engines give off carbon monoxide, an odorless, colorless, poison gas .

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

• Usea3-wireextensioncord.

• First attach extension cord to electric starter connector and then into a wall

receptacle. If additional extension cord is required, use a 3-wire.

• If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualified person in order to avoid a hazard.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Note: Some engines and equipment have remote controls. See the equipment manual

for location and operation of remote controls.

1. Check the oil level. See the How To Check/Add Oil section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Push the stop switch (E), if equipped, to the on position (Figure 5).

Move the throttle control lever (B), if equipped, to the fast

position (Figure 6).

Operate the engine with the throttle control lever in the f ast position.

4. Turn the fuel shut-off valve (A), if equipped, to the on position (Figure 6).

5. Push in the safety key (C).

6. Turn the choke control knob (D) to the choke

position.

Note: Choke is usually unnecessary when restarting a warm engine.

7. Push the primer (F)twotimes.SeeFigure6.

Note: Priming is usually unnecessary when restarting a warm engine.

8. Rewind Start: Firmly hold the starter cord handle (G, Figure 6). Pull the starter cord

handle slowly until resistance is felt, then pull rapidly.

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

WARNING: Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go. Broken bones, fractures,

bruises or sprains could result. When starting engine, pull the starter cord slowly until

resistance is f elt and then pull rapidly to avoid kickback.

9. Electric Start: First connect the extension cord to the power cord receptacle (H,

Figure 7) and then into a wall receptacle. If an additional extension cord is required,

make sure it is a 3-wire.

WARNING: If the extension cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person in order to avoid a

hazard.

10. Electric Start: Depress the push button (I). After you start the engine, first

disconnect the extension cord from the wall receptacle and then from the power cord

receptacle (H).

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

NOTICE: To extend the life of t he starter, use short starting cycles (five seconds

maximum). Wait one minute between starting cycles.

11. Allow the engine to warm up for several minutes. Then, slowly move the choke

control knob to the run

position.

How To Stop The Engine - Figure

8 9

WARNING

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop engine.

1. Move the stop switch (A), if equipped, to the stop position (Figure 8).

Move the throttle control lever (B), if equipped, to slow

and then to the stop

position (Figure 9).

2. Remove the safety key (C, Figure 9). Keep the safety k ey out of reach of children.

3. After the engine stops, turn the fuel shut-off valve (D) to the closed position.

Maintenance

Use only original equipment replacement parts. Other parts may not perform as

well, may damage the unit, and may result in injury. In addition, use of other parts

may void your warranty.

We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts.

NOTICE: All the components used to build this engine must remain in place for proper

operation.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Use only c orrect tools.

• Do not tamper with governor spring, links or other parts to increase engine

speed.

• Replacement parts must be the s ame and installed in the same position as the

original parts.

• Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Maintenance Chart

First 5 Hours

• Change oil

Every8HoursorDaily

• Check engine oil level

Every 50 Hours or Annually

• Change engine oil

• Check muffler and muffler guard

Annually

• Replace spark plug

• Check valve clearance **

** Not required unless engine performance problems are noted.

Not for Reproduction

BRIGGSandSTRATTON.COM

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor was set at the factory to

operate efficiently under most conditions. However, if adjustments are required, see any

Briggs & Stratton Authorized Dealer for service.

NOTICE: The manufacturer of the equipment on which this engine is installed specifies

the top speed at which the engine will be operated. Do not exceed this speed.

How To Replace The Spark Plug - Figure

Check the gap (A, Figure 10) with a wire gauge (B). If necessary, reset the gap. Install

and tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications section.

Note: In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same

type for replacement.

How To Access The Spark Plug - Figure

11 12

To access the spark plug, the snow hood must be removed as follows:

1. Remove the safety key (A, Figure 11). Keep the safety key out of reach of children.

2. Grasp the choke control knob (B) and pull up to remove.

3. Remove the mounting screws (C, Figure 12).

4. Carefully remove the top part of the snow hood (D). Do not disconnect the primer

hose (E) or the stop switch wire (F).

5. The spark plug (G) can now be accessed.

6. Before installation of the snow hood, make sure that the primer hose and the stop

switch wire are connected.

7. Mount the top part of the snow hood to the snow hood base (H). Make sure the t op

interlocks with the base. Secure with the mounting screws.

8. Align the slots in the choke control knob with the tabs on the c hoke shaft (I) and then

push down to install. If the knob is not installed correctly, the choke will not operate.

9. Do not install the safety key until you are ready to start the engine.

Inspect Muffler And Spark Arrester - Figure