Indesit WITP 1021 (EU) Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului
1
GB
WASHING MACHINE
WITP 1021
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Electric and water connections
The first wash cycle
Technical details
Washing machine description, 4-5
Control panel
How to open and shut the drum
Leds
Starting and Programmes, 6
Briefly: how to start a programme
Programme table
Personalisations, 7
Setting the temperature
Functions
Detergents and laundry, 8
Detergent dispenser
Bleach cycle
Preparing your laundry
Special items
Precautions and advice, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning your appliance
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
Cleaning the detergent dispenser
Troubleshooting, 11
Service, 12
Before calling for Assistance
ES
English, 1
GB
ES
Română, 49
RO
CZ
Český, 25
Slovenský, 37
SK
Español, 13
GR
Ελληνικα, 61
2
GB
! Keep this instruction manual in a safe place for future refe-
rence. Should the appliance be sold, transferred or moved,
make sure the instruction manual accompanies the washing
machine to inform the new owner as to its operation and
features.
! Read these instructions carefully: they contain vital infor-
mation on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing
machine.
2. Check whether the
washing machine has been
damaged during transport.
If this is the case, do not
install it and contact your
retailer.
3. Remove the four protec-
tive screws and the rubber
washer with the respective
spacer, situated on the
rear of the appliance (see
figure).
4. Seal the gaps using the
plastic plugs provided.
5. Keep all the parts: you will need them again if the washing
machine needs to be moved to another location.
Warning: should the screws be re-used, make sure you fasten
the shorter ones at the top.
! Packaging materials are not children’s toys.
Levelling
1. Install the washing machine
on a flat sturdy floor, without
resting it up against walls,
furniture cabinets or other.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening or lo-
osening the adjustable front feet
(see figure); the angle of inclina-
tion, measured according to the
worktop, must not exceed .
Levelling your appliance correctly will provide it with stability
and avoid any vibrations, noise and shifting during operation.
If it is placed on a fitted or loose carpet, adjust the feet in
such a way as to allow enough room for ventilation beneath
the washing machine.
Putting your appliance in place and moving it.
If your washing machine
is equipped with a special
set of retractable wheels
you can easy move it.
To lower the wheels and
thus move the appliance
effortlessly, just pull the
lever, situated on the left-
hand side beneath the
base. Once the appliance
is in the required position,
put the lever back in place. The washing machine is now
firmly in place (see figure).
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it is
perfectly clear.
2. Connect the other end of
the water inlet hose to the
washing machine,
screwing it onto the applian-
ces cold water inlet, situated
on the top right-hand side
on the rear of the appliance
(see figure).
3. Make sure there are
no kinks or bends in the
hose.
! The water pressure at the tap must be within the values
indicated in the Technical details table
(on the next page).
! If the water inlet hose is not long enough, contact a
specialist store or an authorised serviceman.
! Never use hoses that have already been used.
Installation
3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between 65
and 100 cm from the floor;
alternatively, place it over
the edge of a basin, sink
or tub, fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
! We advise against the use of hose extensions; in case
of absolute need, the extension must have the same
diameter as the original hose and must not exceed 150
cm in length.
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance’s
maximum power load indicated in the Technical
details table (on the right);
the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
the socket is compatible with the washing
machine’s plug. If this is not the case, replace
the socket or the plug.
! The washing machine should not be installed in an ou-
tdoor environment, not even when the area is sheltered,
because it may be very dangerous to leave it exposed to
rain and thunderstorms.
! When the washing machine is installed, the mains so-
cket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or dange-
rously compressed.
! The power supply cable must only be replaced by an
authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before you
use it for the first time, run a wash cycle with detergent
and no laundry, setting the 90°C programme without a
pre-wash cycle.
65 - 100 cm
Technical details
Model
WITP 1021
Dimensions
40 cm wide
85 cm high
60 cm deep
Capacity
from 1 to 5 kg
Electric
connections
Please refer to the technical data plate
fixed to the machine.
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 42 litres
Spin speed
up to 1000 rpm
Test wash
cycles in
accordance
with directives
1061/2010 and
1015/2010.
Programme : Cotton standard 60°C;
Programme : Cotton standard 40°C.
This appliance is compliant with
the following European Community
Directives:
- 2004/108/CE (Electromagnetic
Compatibility)
- 2006/95/CE (Low Voltage)
- 2002/96/CE
4
GB
ON-OFF/LID LOCK led:
If this LED is on, the appliance Lid is locked to prevent it from being opened accidentally; to avoid any damages, you must
wait for the lamp to flash before you open the Lid.
.
! The rapid flashing of the ON-OFF/LID LOCK Led together with the flashing of at least one other LED indicates there is an
abnormality (see page 11).
Control panel
Washing machine description
ON/OFF
button
TEMPERATURE
knob
START/RESET
button
FUNCTION
Buttons
PROGRAMME
knob
LEDs
LID LOCKED
LED
Detergent dispenser to add detergent and fabric sof-
tener (see page 8).
LEDs to find out which wash cycle phase is under way (see
page 5).
FUNCTION keys to select the functions available.
The button corresponding to the function selected will
remain on.
TEMPERATURE knob to set the temperature or the cold
wash cycle (see page 7).
ON/OFF key to turn the washing machine on and off.
START/RESET key to start the programmes or cancel
incorrect settings.
ON-OFF/LID LOCK led, to find out whether the washing
machine is on (flashing) and if the lid may be opened (see
page 5).
PROGRAMME knob to set the programmes (see page 6).
The knob stays still during the cycle.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON/OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 1W
Consumption in Left-on: 1W
5
GB
Fig. 1
Fig. 2
A) Opening (Fig. 1).
Lift the external lid and open it completely.
B) Then open the drum using both hands as
shown in Fig. 2:
- press the button indicated by the arrow in Fig. 2 lightly
downwards, with one hand firmly resting on the doors to
prevent them from suddenly opening and hurting your fingers;
- therefore follow the appliance doors along as these unhook
and open easily.
C) Loading the washing machine. (Fig. 3).
D) Shutting (Fig. 4).
- close the drum fully by first shutting the front door
followed by the rear one;
- then ensure the hooks on the front door are perfectly
housed within the seat of the rear door;
- after the hooks have clicked into position, press both
doors lightly downwards to make sure they do not
come loose;
- finally shut the external lid.
How to open and to close the drum
Fig. 3
Fig. 4
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding button is
illuminated.
If the function selected is incompatible with the program-
me set, the button will flash and the function will not be
enabled.
If you set a function that is incompatible with another fun-
ction you selected previously, only the last one selected
will be enabled.
Leds
The LEDS provide important information.
This is what they can tell you:
Cycle phase under way:
During the wash cycle, the LEDs gradually illuminate on
to indicate the cycle phase under way:
Prewash
Wash
Rinse
Spin cycle
Note: during draining, the LED corresponding to the Spin
cycle phase will be turned on.
6
GB
Starting and Programmes
Programme table
Briefly: starting a programme
1. Switch the washing machine on by pressing button .
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine, add
the detergent and any fabric softener (see page 8)
and shut the appliance door.
3. Set the PROGRAMME knob to the programme required.
4. Set the wash temperature (see page 7).
5. Start he programme by pressing the START/RESET
button. To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
6. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the washing
machine off by pressing button .
Notes
For the anti-crease function: see opposite page. The information contained in the table is purely indicative.
Cotton Standard 20°C (wash cycle 5) ideal for heavily soiled cotton loads. The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying
speed, with repeated and frequent peaks.
Express (programme
9
for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (
9
at 30°C), you can wash different
fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness
%
Energy
consumption
kWh
Total water lt
Cycle
duration
Pre-
wash
Wash
Fabric
softener
Ble-
ach
Cotton
1
Cotton with prewash: extremely soiled whites. 90° 1000
- 5 62 1,82 64 150’
2
Cotton: extremely soiled whites. 90° 1000 -
5 62 1,90 60 135’
Cotton Standard 60°C (1): heavily soiled whites and resistant colours. 60° 1000 -
5 62 0,88 52 160’
Cotton Standard 40°C (2): lightly soiled whites and delicate colours. 40° 1000 -
5 62 0,91 63 150’
5 Cotton Standard 20°C
20° 1000 -
5 - - - 180’
Synthetics
6
Synthetics: heavily soiled fast colours (baby linen, etc.) 60° 800 -
2,5 44 0,85 39 105’
6
Synthetics (3): heavily soiled fast colours (baby linen, etc.) 40° 800 -
2,5 44 0,53 39 95’
7
Synthetics: heavily soiled fast colours (baby linen, etc.) 50° 800 -
2,5 - - - 100’
8
Synthetics: Delicate colours (all types of slightly soiled garments) 40° 800 -
2,5 - - - 70’
9
Express: to refresh lightly soiled garments quickly (not suitable for wool, silk
and clothes which require washing by hand).
30° 800 -
- 3 71 0,25 33 30’
Delicate
10
Wool: for wool, cashmere, etc. 40° 800 -
- 1 - - - 65’
11
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
- 1 - - - 55’
Partial programmes
Rinse - 1000 - -
5 - - - 36’
Delicate rinse cycle - 1000 - -
5 - - - 31
Spin cycle - 1000 - - - - 5 - - - 16’
Delicate spin cycle - 1000 - - - - 5 - - - 12’
Draining - 0 - - - - 5 - - - 2’
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 6; with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
7
GB
Personalisations
C
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash ( ).
Note. To avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner by conti-
nuously rotating the drum at a speed which is slightly faster than the normal washing speed.
When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than the set
frequency.
If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Option Effect Comments Enabled with
programmes:
Bleaching
Bleaching cycle de-
signed to remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(see page 8).
2,
, , 5,
6, 7, 8, Rinse
cycles.
Extra Rinse
Increases the efficien-
cy of the rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, , ,
5, 6, 7, 8, 10,
11 and Rinse
cycles.
1000
500
Reduces the spin
speed.
All program-
mes except
for 11 and
draining.
Anti-crease
Reduces fabric crea-
sing, making ironing
easier.
Setting this function will interrupt programmes 11 with a laundry
soak (Anti-crease) and the Rinse phase indicator light will blink.
To complete the cycle, press the Anti-crease button.
1, 2,
, , 5,
6, 7, 8, 11.
8
GB
Detergent dispenser
Good washing results also depend on the correct dose of
detergent: adding too much detergent won’t necessarily
make for a more efficient wash, and may in fact cause build
up on the interior of your appliance and even pollute the
environment.
! Do not use hand washing detergents because these crea-
te too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open up the detergent
dispenser and pour in the
detergent and fabric softe-
ner, as follows.
compartment 1: Detergent for pre-wash (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately prior
to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
When pouring the softener in compartment 3, avoid excee-
ding the “max” level indicated.
The softener is added automatically into the machine during
the last wash. At the end of the wash programme, some
water will be left in compartment 3. This is used for the inlet
of denser fabric softeners into the machine, i.e. to dilute the
more concentrated softeners. Should more than a normal
amount of water remain in compartment 3, this means the
emptying device is blocked. For cleaning instructions, see
page 10. The fabric softener should not overflow from the
grid.
compartment 4: Bleach
Bleach cycle
Traditional bleach should be used on sturdy white fabrics,
and delicate bleach for coloured fabrics, synthetics and for
wool.
When pouring in the bleach, be careful not to exceed the
“max” level indicated on compartment 4 (see figure).
To run the bleach cycle alone, pour the bleach into com-
partment 4 and set the Rinse programme (for cotton
fabrics) and push the button Bleaching.
Preparing your laundry
Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from whites.
Empty all pockets and check for loose buttons.
Do not exceed theweight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow case or
mesh bag. Wash them separately without exceeding half
the appliance load. Use programme 11 which excludes
the spin cycle automatically.
Quilted coats and windbreakers: if they are padded
with goose or duck down, they can be machine-washed.
Turn the garments inside out and load a maximum of 2-3
kg, repeating the rinse cycle once or twice and using the
delicate spin cycle.
Wool: for best results, use a specific detergent, taking
care not to exceed a load of 1 kg.
Detergents and laundry
9
GB
Precautions and advice
! The washing machine was designed and built in com-
pliance with the applicable international safety regula-
tions. The following information is provided for your safety
and should consequently be read carefully.
General safety
This appliance has been designed for non-
professional, household use and its functions must
not be changed.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and know-
ledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervi-
sed to ensure that they do not play with the appliance.
This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Never touch the washing machine when barefoot
or with wet or damp hands or feet.
Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
Do not touch the drain water as it could reach
very high temperatures.
Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Always keep children well away from the
appliance while in operation.
Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Before loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream.
Old appliances must be collected separately in order to
optimise the recovery and recycling of the materials they
contain and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on
the product reminds you of your obligation, that when you
dispose of the appliance it must be separately collected.
Consumers may take their old appliance to public waste
collection areas, other communal collection areas, or if
national legislation allows return it to a retailer when pur-
chasing a similar new product.
All major household appliance manufacturers are active
in the creation of systems to manage the collection and
disposal of old appliances.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance door,
this is because thanks to the latest technology, your
washing machine only needs less than half the amount
of water to get the best results: an objective reached to
respect the environment.
Saving on detergent, water, energy and time
To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15% energy.
Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on energy.
Use the correct quantity of detergent depending on
the water hardness, how soiled the garments are and
the amount of laundry you have, to avoid wastage and
to protect the environment: despite being biodegra-
dable, detergents do contain ingredients that alter the
natural balance of the environment. In addition, avoid
using fabric softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board’s peak load.
If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
10
GB
Care and maintenance
Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear
of your appliances water system and also prevent leaks.
Unplug your appliance when cleaning it and during all
maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can be cle-
aned with a soft cloth soaked in lukewarm soapy water. Do
not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see
figure). Wash it under running water; this operation should
be repeated frequently.
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unplea-
sant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump that
does not require any maintenance. Sometimes, small items
(such as coins or buttons) may fall into the pre-chamber that
protects the pump, situated in the lower part of the same.
! Make sure the wash cycle has ended and unplug the
appliance.
To recover any objects that have fallen into the pre-
chamber:
1. remove the plinth at
the bottom on the front
side of the washing
machine by pulling from
the side with your hands
(see figure);
2. unscrew the lid
rotating it anticlock-wise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the interior
thoroughly;
4. screw the lid back on;
5. reposition the panel,
making sure the hooks
are securely in place
before you push it onto
the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you
see any cracks, replace it immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use hoses that have already been used.
How to clean the detergent dispenser
Fig. 1
Fig. 2
Cleaning:
Then clean the dispenser under a tap (fig. 3) using an old
toothbrush and, once the pair of siphons inserted in the
top of compartments 1 and 2 (fig. 4) have been pulled
out, check whether the same are not clogged and then
rinse them.
Reassembly:
Do not forget to reinsert
the pair of siphons into the
special housings and then to
replace the dispenser into its
seat, clicking it into place (fig.
4, 2 and 1).
Disassembly:
Press lightly on the large
button on the front of the
detergent dispenser and pull
it upwards (fig. 1).
Fig. 3
Fig. 4
11
GB
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem can’t easily
be solved by consulting the following list.
Troubleshooting
Problem
The washing machine won’t start.
The wash cycle won’t start.
The washing machine fails to load
water.
The washing machine continuou-
sly loads and unloads water.
The washing machine does not
drain or spin.
The washing machine vibrates too
much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same time
as at least one other LED.
There is too much foam.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to
make contact.
There has been a power failure.
The appliance door is not shut properly. The Lid locked Led flashes.
The button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The free end of the hose is underwater (see page 3).
The wall drainage system doesn’t have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and call for Assistance. If the dwelling is on one of the upper floors of
a building, there may be drain trap problems causing the washing machine to load
and unload water continuously. In order to avoid such an inconvenience, special
anti-drain trap valves are available in shops.
The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
The Anti-crease option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The drain hose is bent (see page 3).
The drain duct is clogged.
The drum was not unblocked correctly during installation (see page 2).
The washing machine is not level (see page 2).
The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The water inlet hose is not screwed on correctly (see page 2).
The detergent dispenser is obstructed (to clean it, see page 10).
The drain hose is not secured properly (see page 3).
Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
The detergent is not suitable for machine washing (it should bear
the definition “for washing machines” orhand and machine wash”,or the like).
You used too much detergent.
12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
! Always request the assistance of authorised servicemen.
Notify the operator of:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
Service
13
ES
Español
WITP 1021
ES
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Descripción de la lavadora, 16-17
Panel de control
Cómo abrir y cerrar el cesto
Luces testigo
Puesta en marcha y Programas, 18
En la práctica: poner en marcha un programa
Tabla de programas
Personalizaciones, 19
Seleccione la temperatura
Funciones
Detergentes y ropa, 20
Cajón de detergentes
Ciclo de blanqueo
Preparar la ropa
Prendas especiales
Precauciones y consejos, 21
Seguridad general
Eliminaciones
Ahorrar y respetar el ambiente
Mantenimiento y cuidados, 22
Excluir el agua y la corriente eléctrica
Limpiar la lavadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Cómo limpiar la cubeta de detergente
Limpiar la bomba
Anomalías y soluciones, 23
Asistencia, 24
Antes de llamar a la Asistencia Técnica
LAVADORA
Instrucciones para el uso
14
ES
! Es importante conservar este manual para poder consul-
tarlo en cualquier momento. En caso de venta, de cesión o
de traslado, verifique que permanezca junto con la lavadora
para informar al nuevo propietario sobre el funcionamiento y
brindar las correspondientes advertencias.
! Lea atentamente las instrucciones: ellas contienen impor-
tante información sobre la instalación, el uso y la seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavadora.
2. Controle que la lavadora
no haya sufrido daños du-
rante el transporte. Si estu-
viera dañada no la conecte
y llame al revendedor.
3. Quite los cuatro tornil-
los de protección para el
transporte y la arandela de
goma con el correspon-
diente distanciador, ubica-
dos en la parte posterior
(ver la figura).
4. Cierre los orificios con
los tapones de plástico su-
ministrados con el aparato.
5. Conserve todas las piezas: cuando la lavadora deba ser tran-
sportada nuevamente, deberán volver a colocarse.
Atención: si vuelve a utilizar los tornillos más cortos, se deben
colocar arriba.
! Los embalajes no son juguetes para los niños.
Nivelación
1. Instale la lavadora sobre un
piso plano y rígido, sin apoyarla
en las paredes, muebles ni en
ningún otro aparato.
2. Si el piso no es perfecta-
mente horizontal, compense
las irregularidades desenro-
scando o enroscando los pies
delanteros (véase la figura); el
ángulo de inclinación medido
sobre la superficie de trabajo,
no debe superar los 2º.
Una cuidadosa nivelación brinda estabilidad a la máquina
y evita vibraciones, ruidos y desplazamientos durante el
funcionamiento. Cuando se instala sobre moquetas o alfom-
bras, regule los pies para conservar debajo de la lavadora
un espacio suficiente para la ventilación.
Instalación, desplazamientos.
Si su lavadora està dotada
de un carro especial con
ruedas retráctiles, se faci-
litarà su desplazamiento.
Para hacer descender este
carro y poder moverla sin
esfuerzo, es necesario tirar
la palanca, situada abajo
a la izquierda, debajo del
zócalo. Finalizado el de-
splazamiento es necesario
devolverla a su posición
inicial. A partir de ese momento, la máquina está sólida-
mente colocada.
Conexiones hidráulicas y eléctricas
Conexión del tubo de alimentación de agua
1. Conectar el tubo de
tubo enroscándolo a un
grifo de agua fría con la
boca roscada de 3/4 gas
(ver la figura).
Antes de conectarlo, haga
correr el agua hasta que
esté límpida.
2. Conecte el tubo de
alimentación a la lavadora
enroscándolo en la toma
de agua correspondiente
ubicada en la parte poste-
rior arriba y a la derecha
(véase la figura).
3. Verifique que el tubo no
tenga pliegues ni estran-
gulaciones.
! La presión de agua del grifo debe estar comprendida
dentro de los valores contenidos en la tabla de Datos
técnicos (ver la página del costado).
! Si la longitud del tubo de alimentación no fuera sufi-
ciente, diríjase a una tienda especializada o a un técnico
autorizado.
! No utilice nunca tubos ya usados.
Instalación
15
ES
Conexión del tubo de descarga
Conecte el tubo de descar-
ga, sin plegarlo, a un de-
sagüe de pared ubicado
a una distancia del piso
comprendida entre 65 y
100 cm;
o apóyelo al borde de un
lavabo o de una bañera,
uniendo la guía sumini-
strada con el aparato,
al grifo (véase la figura).
El extremo libre del tubo
de descarga no debe
permanecer sumergido
en el agua.
! No se aconseja utilizar tubos de prolongación, de todos
modos, si es indispensable, la prolongación debe tener
el mismo diámetro del tubo original y no superar los 150
cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
la toma tenga la conexión a tierra y haya sido hecha
según las normas legales;
la toma sea capaz de soportar la carga máxima de
potencia de la máquina indicada en la tabla de Datos
técnicos (ver al costado);
la tensión de alimentación esté comprendida dentro
de los valores indicados en la tabla de Datos técnicos
(ver al costado);
la toma sea compatible con el enchufe de la lavadora.
Si no es así, sustituya la toma o el enchufe.
! La lavadora no debe ser instalada al aire libre, ni siquiera
si el lugar está preparado, ya que es muy peligroso dejarla
expuesta a la lluvia o a las tormentas.
! Una vez instalada la lavadora, la toma de corriente debe
ser fácilmente accesible.
! No utilice alargadores ni conexiones múltiples.
! El cable no debe estar plegado ni sufrir compresiones.
! El cable de alimentación debe ser sustituido sólo por
técnicos autorizados.
¡Atención! La empresa fabricante declina toda responsa-
bilidad en caso de que estas normas no sean respeta-
das.
Primer ciclo de lavado
Después de la instalación y antes del uso, realice un ciclo
de lavado con detergente y sin ropa, seleccionando el
programa a 90ºC sin prelavado.
65 - 100 cm
Datos técnicos
Modelo
WITP 1021
Dimensiones
ancho 40 cm.
altura 85 cm.
profundidad 60 cm.
Capacidad
de 1 a 5 kg.
Conexiones
eléctricas
Ver la placa de características técni-
cas aplicada en la máquina
Conexiones
hídricas
presión máxima 1 MPa (10 bar)
presión mínima 0,05 MPa (0,5 bar)
capacidad del cesto 42 litros
Velocidad de
centrifugado
máxima 1000 r.p.m.
Programas de
control según
las directivas
1061/2010 y
1015/2010.
Programa
: programa normal de
algodón a 60 °C;
Programa
: programa normal de
algodón a 40 °C.
Esta máquina cumple con lo estable-
cido por las siguientes Directivas de la
Comunidad:
- 2004/108/CE (Compatibilidad Elec-
tromagnética)
- 2006/95/CE (Baja Tensión)
- 2002/96/CE
16
ES
Control panel
Luz indicadora de ENCENDIDO/PUERTA BLOQUEADA:
La luz testigo encendida indica que la puerta está bloqueada para impedir aperturas accidentales; para evitar daños es nece-
sario esperar que la luz testigo centellee antes de abrirla.
! El centelleo rápido de la luz indicadora de ENCENDIDO/PUERTA BLOQUEADA simultáneamente con, al menos, el de otra
luz testigo, indica una anomalía (ver la pág. 23).
Botón
START/RESET
Contenedor de detergentes para cargar detergentes y
aditivos (véase la pág. 20).
Luces testigo para seguir el estado de avance del progra-
ma de lavado.
Botones de FUNCIÓN para seleccionar las funciones
disponibles. El botón correspondiente a la función seleccio-
nada permanecerá encendido.
Perilla de TEMPERATURA para seleccionar la temperatura
o el lavado en frío (ver la pág. 19).
Botón de ENCENDIDO/APAGADO para encender y apa-
gar la lavadora.
Botón START/RESET para poner en marcha los progra-
mas o anular las selecciones incorrectas.
Luz testigo de ENCENDIDO/TAPA BLOQUEADA para
saber si la lavadora está encendida (centelleante) y si la
tapa se puede abrir (fija) (véase la pág. 17).
Perilla de PROGRAMAS para seleccionar los programas
(véase la pág. 18).
Durante el programa la perilla no se mueve.
Modalidad de stand by
Esta lavasecadora está en conformidad con las nuevas
normativas vinculadas al ahorro energético. Está dota-
da de un sistema de auto-apagado (stand by) que, en
caso de no funcionamiento, se activa pasados aproxi-
madamente 30 minutos. Presionar brevemente el botón
ENCENDIDO/APAGADO
y esperar que la máquina se
active.
Consumo en off-mode: 1 W
Consumo en Left-on: 1W
Descripción de la lavadora
Perilla de
TEMPERATURA
Perilla de
PROGRAMAS
Luces
testigo
Botones
FUNCIÓN
Botón
ENCENDIDO/
APAGADO
Luz testigo de
TAPA BLOQUEADA
17
ES
Cómo abrir y cerrar el cesto
A) ABERTURA (Fig. 1)
Levante la tapa externa y ábrala completamente.
B) Abertura luego el cesto usando ambas manos,
como se indica en la Fig.2:
- presione el botón indicado por la flecha en la fig.2
y ejerciendo una leve presión hacia abajo, mantenga
apoyada una mano para evitar que las puertas se
abran repentinamente haciendo mal a los dedos;
- luego acompañe las puertitas que se desengan
charán y se abrirán fácilmente.
C) INTRODUCCIÓN DE LA ROPA (Fig. 3)
D) CIERRE (Fig. 4)
- cierre bien el cesto bajando primero la puerta
delantera y apoyando luego la posterior;
- luego verifique que los ganchos de la puerta delantera
estén perfectamente alojados en la sede de la puerta
posterior;
- después de haber escuchado el “clac” correspondi
ente al enganche, ejerza una leve presión hacia abajo
sobre ambas puertas que no se deben desenganchar;
- por último cierre la tapa externa.
Fig. 1
Fig. 2
Botones de FUNCIÓN
Los BOTONES DE FUNCN también actúan como luces
testigo.
Al seleccionar una función, el botón correspondiente se
iluminará.
Si la función seleccionada no es compatible con el progra-
ma elegido, el bon centelleará y la función no se activará.
Cuando se seleccione una función incompatible con otra
seleccionada precedentemente, permanecerá activalo la
última elección realizada.
Luces testigo
Las luces testigo suministran información importante.
He aquí lo que nos dicen:
Fase en curso:
Durante el ciclo de lavado, las luces testigo se encen-
derán progresivamente para indicar su estado de avance.
Prelavado
Lavado
Aclarado
Centrifugado
Nota: durante la fase de descarga se iluminará la luz
testigo correspondiente a la fase de Centrifugado.
Fig. 3
Fig. 4
18
ES
Puesta en marcha y Programas
Tabla de programas
En la práctica: poner en marcha un programa
1. Encienda la lavadora pulsando el botón . Todas las luces
testigo se encenderán durante algunos segundos, luego se
apagarán y la luz indicadora de ENCENDIDO/PUERTA BLO-
QUEADA comenzará a centellear.
2. Cargue la ropa, vierta el detergente y los aditivos (véase la pág.
20) y por último cierre las puertas y la tapa.
3. Seleccione el programa deseado con el mando de PROGRAMAS.
4. Fije la temperatura de lavado (ver la pág. 19).
5. Ponga en marcha el programa pulsando el botón START/
RESET. Para anular, mantenga presionado el botón START/
RESET durante 2 segundos como mínimo.
6. Al finalizar el programa, la luz indicadora de ENCENDIDO/
PUERTA BLOQUEADA centelleará indicando que la puerta
se puede abrir. Extraiga la ropa y deje la puerta semicerrada
para permitir que el cesto se seque. Apague la lavadora
pulsando el botón .
Nota
Para la descripción del antiarrugas: consulte página siguiente. Los datos contenidos en la tabla tienen un valor indicativo.
Programa normal de algodón a 20 °C (programa 5) ideal para cargas de prendas de algodón sucias. Los buenos rendi-
mientos aún en frío, comparables con los de un lavado a 40º, están garantizados por una acción mecánica que trabaja con
variación de velocidad con picos repetidos y cercanos.
Express (programa
9
para Sintéticos) fue estudiado para lavar prendas ligeramente sucias y en poco tiempo: dura sólo 30
minutos y de esa manera hace ahorrar energía y tiempo. Seleccionando el programa (
9
a 30ºC) es posible lavar conjuntamente
tejidos de distinto tipo (excluidas lana y seda), con una carga máxima de 3 kg. Se aconseja el uso de detergente líquido.
La duración del ciclo que se indica en el visor o en el manual es una estimación calculada en base a condiciones estándar. El tiempo efectivo puede
variar en función de numerosos factores como la temperatura y la presión del agua de entrada, la temperatura ambiente, la cantidad de detergente,
la cantidad y el tipo de carga, el equilibrado de la carga y las opciones adicionales seleccionadas.
1) Programa de control según la directiva 1061/2010: seleccione el programa con una temperatura de 60ºC.
Este ciclo es adecuado para limpiar una carga de algodón normalmente sucia, es el más eficiente en lo que se refiere al consumo combinado con la
energía y la cantidad de agua y se usa con prendas lavables a 60ºC. La temperatura efectiva de lavado puede diferir de la indicada.
2) Programa de control según la directiva 1061/2010: seleccione el programa con una temperatura de 40ºC.
Este ciclo es adecuado para limpiar una carga de algodón normalmente sucia, es el más eficiente en lo que se refiere al consumo combinado con la
energía y la cantidad de agua y se usa con prendas lavables a 40ºC. La temperatura efectiva de lavado puede diferir de la indicada.
Para todos los Test Institutes:
2) Programa algodón largo: seleccione el programa con una temperatura de 40ºC.
3) Programa sintético largo: seleccione el programa 6 con una temperatura de 40ºC.
Programas
Descripción del Programa
Temp.
max.
C)
Velocidad
x.
(r.p.m.)
Detergentes
Carga máx.
(Kg.)
Humedad
residual %
Consumo de
energía kWh
Agua total lt
Duracn del
ciclo
Prela-
vado
Lavado Suavizante
Blanquea-
dor
Algodón
1
Prelavado Algodón: blancos sumamente sucios.
90° 1000
- 5 62 1,82 64 150’
2
Algodón: blancos sumamente sucios.
90° 1000 -
5 62 1,90 60 135’
Programa normal de algodón a 60 °C (1): blancos y colores resistentes
muy sucios.
60° 1000 -
5 62 0,88 52 160’
Programa normal de algodón a 40 °C (2): blancos y colores delicados
muy sucios.
40° 1000 -
5 62 0,91 63 150’
5 Programa normal de algodón a 20 °C
20° 1000 -
5 - - - 180’
Sintéticos
6
Sintéticos:
Colores resistentes muy sucios (ropa para recién nacidos, etc.)
60° 800 -
2,5 44 0,85 39 105’
6
Sintéticos (3):
Colores resistentes muy sucios (ropa para recién nacidos, etc.)
40° 800 -
2,5 44 0,53 39 95’
7
Sintéticos:
Colores resistentes muy sucios (ropa para recién nacidos, etc.)
50° 800 -
2,5 - - - 100’
8
Sintéticos:
Colores delicados (ropa de todo tipo poco sucia)
40° 800 -
2,5 - - - 70’
9
Express: para refrescar pidamente prendas poco sucias (no se aconseja utilizar-
lo para lana, seda y prendas para lavar a mano).
30° 800 -
- 3 71 0,25 33 30’
Delicados
10
Lana: para lana, cachemira, etc.
40° 800 -
- 1 - - - 65’
11
Seda/Cortinas: para prendas de seda, viscosa, lencería.
30° 0 -
- 1 - - - 55’
Programas parciales
Aclarado
- 1000 - -
5 - - - 36’
Aclarado delicado
- 1000 - -
5 - - - 31
Centrifugado
- 1000 - - - - 5 - - - 16’
Centrifugado delicado
- 1000 - - - - 5 - - - 12’
Desagüe
- 0 - - - - 5 - - - 2’
19
ES
Personalizaciones
C
Seleccione la temperatura
Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas en la pág. 18).
La temperatura se puede disminuir hasta el lavado en frío ( ).
! Para evitar vibraciones excesivas, antes de cada centrifugado, la máquina distribuye la carga de modo uniforme, esto se
produce efectuando rotaciones continuas del cesto a una velocidad ligeramente superior a la del lavado.
Aún cuando después de repetidos intentos, la carga no se distribuye perfectamente, la máquina realiza el centrifugado a
una velocidad inferior a la prevista.
Cuando existe un excesivo desequilibrado, la máquina efectúa la distribución en lugar del centrifugado.
Los intentos de equilibrado pueden aumentar la duración total del ciclo hasta un máximo de 10 minutos.
Funciones
Las distintas funciones de lavado previstas por la lavadora permiten obtener la limpieza y el blanco deseados. Para activar
las funciones:
1. pulse el botón correspondiente a la función deseada de acuerdo con la tabla que se encuentra debajo;
2. el encendido del botón correspondiente indica que la función está activa.
Nota: El centelleo rápido del botón indica que la función correspondiente no se puede seleccionar para el programa elegido.
Funciones Efecto Notas para el uso Activa con los
programas:
Antimancha
Ciclo de blanqueo
adecuado para eli-
minar las manchas
más resistentes.
Recuerde verter el blanqueador en la cubeta adicional 4 (ver la
pág. 20).
2,
, , 5,
6, 7, 8, Acla-
rado.
Enjuague
Extra
Aumenta la eficacia
del enjuague.
Es aconsejable con la lavadora a plena carga o con dosis elevadas
de detergente.
1, 2,
, ,
5, 6, 7, 8, 10,
11 Aclarado
1000
500
Disminuye la veloci-
dad de centrifuga-
do.
Todos excep-
to el 11 y la
Descarga.
Antiarrugas
Reduce las arrugas
en los tejidos, facili-
tando el planchado
Seleccionando esta función, los programas 11 se interrumpirán con
la ropa en remojo (Antiarrugas) y el piloto de la fase Aclarado
centelleará:
Para completar el ciclo, pulse el botón Antiarrugas.
1, 2,
, ,
5, 6, 7, 8, 11.
20
ES
Cajón de detergentes
El buen resultado del lavado depende también de la cor-
recta dosificación del detergente: si se excede la cantidad,
no se lava de manera más eficaz, sino que se contribuye a
encostrar las partes internas de la lavadora y a contaminar
el ambiente.
! No use detergentes para el lavado a mano porque produ-
cen demasiada espuma.
! Utilice detergentes en polvo para prendas de algodón
blancas, para el prelavado y para lavados con una tempera-
tura mayor que 60ºC.
! Respete las indicaciones que se encuentran en el envase
de detergente.
Extraiga el cajón de de-
tergentes e introduzca el
detergente o el aditivo de
la siguiente manera:
cubeta 1: Detergente para prelavado (en polvo)
cubeta 2: Detergente para lavado (en polvo o líquido)
El detergente líquido es conveniente colocarlo directamente
en la cuba utilizando la correspondiente bola de dosificación.
cubeta 3: Aditivos (suavizante, etc.)
Cuando vierta el suavizante en el compartimiento 3, tenga
cuidado de no superar el nivel “max” indicado.
El suavizante se introduce automáticamente
en la máquina durante el último aclarado. Al finalizar el
programa de lavado, en el compartimiento 3 permanece
una cantidad residual de agua. La función de la misma es la
introducción de suavizantes muy densos o diluir a aquellos
concentrados. Si en el compartimiento 3 permaneciera más
agua de la normal, esto significa que el dispositivo de vacia-
do está obstruido. Para la limpieza, véase la pág. 22.
cubeta 4: Blanqueador
Ciclo de blanqueo
El blanqueador tradicional debe utilizarse para los tejidos
resistentes blancos, mientras que el delicado debe utilizar-
se para la lana y los tejidos coloreados y sintéticos.
Al verter el blanqueador no debe superar el nivel “máx.” indi-
cado en la cubeta 4 (véase la figura).
Para realizar sólo el blanqueo, vierta el blanqueador en la cu-
beta 4 y seleccione el programa Aclarado (para los tejidos
de algodón) y pulse el botón-función Antimancha .
Detergentes y ropa
Preparar la ropa
Subdivida la ropa según:
- el tipo de tejido / el símbolo en la etiqueta.
- los colores: separe las prendas de color y las blancas.
Vacíe los bolsillos y controle los botones.
No supere los valores indicados, referidos al peso de
la ropa seca:
Tejidos resistentes: max 5 kg.
Tejidos sintéticos: max 2,5 kg.
Tejidos delicados: max 2 kg.
Lana: max 1 kg.
¿Cuánto pesa la ropa?
1 sábana 400/500 g
1 funda 150/200 g
1 mantel 400/500 g
1 albornoz 900/1.200 g
1 toalla 150/250 g
Prendas especiales
Cortinas: pliéguelas y colóquelas dentro de una funda
o de una bolsa de red. Lávelas solas sin superar la media
carga. Utilice el programa 11 que excluye automáticamente
el centrifugado.
Cazadoras acolchadas con plumas y anoraks: si el
relleno es de pluma de ganso o de pato, se pueden lavar en
la lavadora. Poner las prendas del revés y realizar una carga
xima de 2-3 kg. repitiendo el enjuague una o dos veces y
utilizando el centrifugado delicado.
Lana: para obtener los mejores resultados, utilice un de-
tergente específico y no supere 1 kg. de carga.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Indesit WITP 1021 (EU) Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului