Yamaha CD-S700 Manualul proprietarului

Compact Disc Player

Lecteur Compact Disque

G

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

i

CAUTION

VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN. AVOID EXPOSURE TO BEAM.

ADVARSEL

SYNLIG OG USYNLIG LASERSTRALING VED

ÅBNING. UNDGÅ UDSÆTTELSE FOR STRÅLING.

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING NÅR

DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR

STRÅLEN.

VARNING

SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ

STRÅLEN.

VARO!

AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA

NÄKYMÄTTÖMÄLLE LASER SÄ TEILYLLE. ÄLÄ

KATSO SÄTEESEEN.

VORSICHT

SICHTBARE UND UNSICHTBARE

LASERSTRAHLUNG WENN ABDECKUNG

GEÖFFNET. NICHT DEM STRAHL AUSSETSEN.

DANGER

VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN. AVOID DIRECT EXPOSURE TO

BEAM.

ATTENTION

RAYONNEMENT LASER VISIBLE ET INVISIBLE EN

CAS D’OUVERTURE. EXPOSITION DANGEREUSE

AU FAISCEAU.

ПРЕДУПРЕЖДЕНИЕ

ПPИ OTKPЫTИИ УCTPOЙCTBA BЫ MOЖETE

ПОДBEPГHУTБСЯ ВОЗДЕЙСТВИЮ BИДИMOГO И

HEBИДИMOГO ЛAЗEPHOГO ИЗЛУЧEHИЯ.

ИЗБЕГAИTE BOЗДЕЙСТВИЯ ЛУЧA.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou

de méthodes autres que ceux décrits ci-dessous,

peuvent entraîner une exposition à un rayonnement

dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die

Einstellung bzw. die Ausführung von anderen als in

dieser Anleitung beschriebenen Vorgängen kann zu

Gefährdung durch gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande

av åtgärder på annat sätt än så som beskrivs häri kan

resultera i farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure

non specificati in questo manuale possono risultare in

esposizione a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos

que no se especifican enste manual pueden causar una

exposición peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of

procedures anders dan beschreven in dit document kan

leiden tot blootstelling aan gevaarlijke stralen.

ЕРЕЖЕНИЕ

Использование органов управления или произведение

настроек или выполнение процедур, не указанных в

данной инструкции, может отразиться на выделении

опасной радиации.

ii

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai

asetusten muutto saattaa altistaa vaaralliselle säteilylle tai

muille vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse

for stråling.

Bemærk: Netafbryderen POWER er sekundært indkoblet

og ofbryder ikke strømmen fra nettet. Den indbyggede

netdel er derfor tilsluttet til lysnettet så længe netstikket

sidder i stikkontakten.

N

Observer: Nettbryteren POWER er sekundert innkoplet.

Den innebygdenetdelen er derfor ikke frakoplet nettet så

lenge apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för

laserklass 1.

Observera! Strömbrytaren POWER är sekundärt kopplad

och inte bryter inte strömmen från nätet. Den inbyggda

nätdelen är därför ansluten till elnätet så länge

stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä

käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina

tippu-ja roiskevedelle.

Huom. Toiminnanvalitsin POWER on kytketty

toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä

sähköverkkoon aina silloin, kun pistoke on pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

ÄLÄ KATSO SÄTEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

10 cm (3 15/16 in) on the top, 10 cm (3 15/16 in) on the left

and right, and 10 cm (3 15/16 in) on the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cables.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage resulting

from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or the unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the power cable from the wall

outlet.

16 Install this unit near the wall outlet and where the power cable

can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section in this

manual on common operating errors before concluding that

this unit is faulty.

18 Before moving this unit, press POWER to turn off this unit

and then disconnect the power cable from the wall outlet.

19 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

20 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the wall outlet. Voltages are:

.....................................AC 110/120/220/230-240 V, 50/60 Hz

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a qualified

service person should remove the cover or attempt to service this

device.

DANGER

This unit emits visible laser radiation when open. Avoid direct eye

exposure to beam. When this unit is plugged into the wall outlet, do

not place your eyes close to the opening of the disc tray and other

openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

As long as this unit is connected to the wall outlet, it is

not disconnected from the AC power source even if

you turn off this unit by POWER.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

The laser component in this product is capable of

emitting radiation exceeding the limit for Class 1.

1 En

PREPARATIONINTRODUCTION

OPERATION

ADDITIONAL

INFORMATION

English

FEATURES............................................................. 2

SUPPLIED ACCESSORIES ................................. 2

CONTROLS AND FUNCTIONS ......................... 3

Front panel................................................................. 3

Front panel display .................................................... 4

Remote control........................................................... 5

Installing batteries in the remote control ................... 6

Using the remote control ........................................... 6

CONNECTIONS .................................................... 7

Connecting your amplifier......................................... 7

Connecting the supplied power cable........................ 8

Connecting USB devices........................................... 8

BASIC OPERATION............................................. 9

Starting playback ....................................................... 9

Pausing playback ..................................................... 10

Stopping playback ................................................... 10

Turning off the power.............................................. 10

Playing back a desired track .................................... 10

To improve audio quality (PURE DIRECT mode)

............................................................................. 10

Skipping to the beginning of a desired track ........... 11

Advancing or reversing playback rapidly................ 11

Changing front panel display................................... 12

Changing the brightness of the front panel display

............................................................................. 12

RANDOM-SEQUENCE PLAY .......................... 13

REPEAT PLAY .................................................... 13

Repeating a selected item ........................................ 13

Repeat A-B .............................................................. 14

PROGRAM PLAY ............................................... 15

Stopping program playback..................................... 16

Clearing programmed track ..................................... 16

NOTES ABOUT DISCS/MP3, WMA FILES .... 17

TROUBLESHOOTING....................................... 19

SPECIFICATIONS .............................................. 20

CONTENTS

INTRODUCTION

PREPARATION

OPERATION

ADDITIONAL INFORMATION

■ About this manual

• y indicates a tip for your operation.

• In this manual, audio CDs are referred to as “Audio CD”, MP3/WMA discs as “Data Disc”, and MP3/WMA files

stored on the USB device as “USB”.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

2 En

INTRODUCTION

◆ Optical Digital Output

◆ Coaxial Digital Output

◆ CD-R, CD-RW Disc Playability

(For details, refer to page 17.)

◆ MP3, WMA Disc Playability

◆ MP3, WMA File Playability Stored on USB Device

◆ Program Play (Audio CD only)

◆ Random-Sequence Play

◆ Single Track/Entire Disc Repeat Play

◆ Repeat A-B Play (Audio CD only)

◆ Adjustable Display Information and Brightness

◆ PURE DIRECT Function

Please check that you received all of the following parts:

FEATURES

SUPPLIED ACCESSORIES

Remote control RCA stereo cable

Batteries (× 2)

(AA, R6, UM-3)

Power cable

3 En

English

INTRODUCTION

1 POWER

Press to turn the power to ON/OFF.

y

The POWER indicator above lights up when this unit is turned

on.

2 USB port

Connect your USB device. See page 8 for details.

3 PURE DIRECT

Turn PURE DIRECT mode on or off to improve audio

quality.

y

The PURE DIRECT indicator above lights up when this unit is in

PURE DIRECT mode. See page 10 for details.

4 Disc tray

Load a disc.

5 (Open/Close)

Open or close the disc tray.

6 / (Skip/Search backward),

/ (Skip/Search forward)

/ : Skip to the next track.

/ : Skip back to the beginning of the current

track.

/ (twice): Skip to the previous track.

Press and hold / or / to search

backward/ forward.

y

Each time you press and hold / or / , the

search speed increases by 2 levels.

7 (Play)

Start playback.

8 (Pause)

Pause playback. Press or to resume playback.

9 (Stop)

Stop playback.

0 USB indicator

Lights on/off when this unit is in USB/disc mode, and

blinks when this unit is reading the USB device.

A Front panel display

Shows the current status of this unit.

B Remote control sensor

Receives signals from the remote control.

CONTROLS AND FUNCTIONS

Front panel

CONTROLS AND FUNCTIONS

4 En

1 Lights up the icon for the selected playback mode.

2 Shows the time displays. (Refer to page 12.)

3 Shows the track number selected or being played back.

4 Shows the file number.

5 Lights up when this unit is in disc mode (refer to page 9) and

also when an Audio CD is recognized on the tray.

6 Lights up when MP3 file is played back.

7 Lights up when WMA file is played back.

Front panel display

Audio CD

Data Disc USB

English

CONTROLS AND FUNCTIONS

5 En

INTRODUCTION

1 Infrared signal transmitter (p. 6)

Send infrared signals to this unit.

2 CD/USB (p. 9)

Switch between disc mode and USB mode.

3 DIMMER (p. 12)

Select brightness level for the front panel display.

4 Numeric buttons (p. 10)

Select a track directly.

5 PROGRAM (p. 15)

Turn program mode on or off.

6 / (Search backward/forward) (p. 11)

Search tracks backward/forward.

7 / (Skip backward/forward) (p. 11)

Skip to the next/previous track or skip back to the

beginning of the current track.

8 OPEN/CLOSE (p. 9)

Open or close the disc tray.

9 PURE DIRECT (p. 10)

Turn PURE DIRECT mode on or off.

0 DISPLAY (p. 12)

Switch the time display.

A ENTER (p. 15)

Confirm the track number when this unit is in program

input mode.

B CLEAR (p. 16)

Clear programmed track.

C REPEAT (p. 13)

Repeat playback of a single track or all tracks.

D RANDOM (p. 13)

Set random-sequence play.

E A/B (p. 14)

Set repeat A-B.

F (Pause) (p. 10)

Pause playback.

G (Play) (p. 9)

Start playback.

H (Stop) (p. 10)

Stop playback.

Remote control

CONTROLS AND FUNCTIONS

6 En

1 Press the part and slide the battery

compartment cover off.

2 Insert two supplied batteries (AA, R6, UM-3)

according to the polarity markings (+ and –)

on the inside of the battery compartment.

3 Slide the cover back until it snaps into place.

■ Notes on batteries

• Change both batteries when the operation range of the

remote control decreases.

• Use AA, R6, UM-3 batteries.

• Make sure that the polarities are correct. See the

illustration inside the battery compartment.

• Remove the batteries if the remote control is not to be

used for an extended period of time.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean the

battery compartment thoroughly before installing new

batteries.

• Do not throw away batteries with general house waste;

dispose of them correctly in accordance with your local

regulations.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of this unit during

operation.

■ Handling the remote control

• The area between the remote control and this unit must

be clear of large obstacles.

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity, such as near a bath

– high temperature, such as near a heater or a stove

– extremely low temperatures

– dusty places

• Do not expose the remote control sensor to strong

lighting, in particular, an inverter type fluorescent

lamp; otherwise, the remote control may not work

properly. If necessary, position the unit away from

direct lighting.

Installing batteries in the remote

control

Using the remote control

Within 6 m

(20 ft)

English

7 En

PREPARATION

• Before making any connection, switch OFF the power to the unit, the amplifier and any other component.

• Connections should be made to the correct input terminals of the amplifier or another component.

• If the placement of this unit causes noise to another equipment, such as a tuner, move them further away from each

other.

To connect this unit to your amplifier, choose one of the ways listed below.

When the ANALOG OUT terminals of this

unit are used ( )

Connect these terminals to the CD (or AUX) terminals of

the amplifier by using a supplied RCA stereo cable. For

details concerning these connections, refer to the

operation instructions of the amplifier being used.

• Be sure that the left (L) and right (R) of these terminals

are connected to the corresponding (left and right)

terminals of the amplifier or other component.

When the DIGITAL OUT (OPTICAL) terminal

of this unit is used ( )

Connect this terminal to the optical input terminal of an

amplifier with a commercially available optical cable.

• Use a reliable optical cable.

When the DIGITAL OUT (COAXIAL) terminal

of this unit is used ( )

Connect this terminal to the digital input terminal of an

amplifier with a commercially available coaxial cable.

CONNECTIONS

Connecting your amplifier

CAUTION

Coaxial cableOptical cable

Amplifier

RCA stereo

cable

(supplied)

• The digital output is turned off when this unit is in PURE DIRECT mode.

CONNECTIONS

8 En

■ VOLTAGE SELECTOR

(Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

the supplied power cable into the wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a straight

slot screwdriver.

Voltages are as follows:

.............................. AC 110/120/220/230-240 V, 50/60 Hz

■ Connecting this unit to the wall outlet

Plug the supplied power cable into the AC IN on the rear

panel of this unit and then plug the power cable into the

wall outlet after all other connections are complete.

This unit has a USB port and can access MP3 or WMA

files saved on your USB device. Connect your USB

device to the USB port on the front panel of this unit.

Do not disconnect your USB device while playing back

from the USB device, or when the USB indicator blinks.

■ Supported USB devices

This unit supports USB mass storage class devices (e.g.,

flash memories, card readers or portable audio players)

that use FAT16 or FAT32 format.

• Some devices may not work properly even if they meet the

requirements.

• Do not connect devices other than USB mass storage class

devices: USB chargers, USB hubs, PCs, external HDD, etc.

• When you insert two or more memory cards at the same time

into a card reader connected to the USB port on this unit, only

one of the memory cards is recognized.

• Yamaha and suppliers accepts no liability for the loss of data

saved on the USB devices connected to this unit. As a

precaution, it is recommended that the files are made backup

copies.

• Playability of and power supply to all kind of USB devices are

not guaranteed.

Connecting the supplied power

cable

To the wall outlet with the

supplied power cable

Asia and General models

only

Europe and U.K. models

Connecting USB devices

CAUTION

Notes

English

9 En

OPERATION

This manual describes how to operate this unit by using the remote control.

To operate this unit from the front panel, use the corresponding buttons on the front panel.

The , and icons indicate music data formats that can be

used in the operation.

1 Press POWER to turn on the power.

2 Press CD/USB to switch between disc mode

and USB mode.

When USB mode is selected, the USB indicator lights

up, and when disc mode is selected, the USB

indicator lights off.

y

This setting is retained even if you turn off this unit.

■ Playing back discs

1 Press OPEN/CLOSE to open the disc tray,

and load a disc.

• When you load a disc, set the disc on the inside of the disc

guides (4 marks on the disc tray).

• The disc may not be read correctly, if it is set incorrectly. In this

case, open the disc tray and set the disc again.

2 Press OPEN/CLOSE to close the disc tray.

y

You can also close the disc tray by pressing h, a numeric button,

or by pressing the front edge of the disc tray gently. If the tray is

closed in one of these ways, playback starts automatically.

3 Press h to start playback.

For an Audio CD, playback starts from the first track,

and for a Data Disc, in alphanumeric order by

filename.

BASIC OPERATION

Audio CD Data Disc USB

Starting playback

Audio CD Data Disc

Disc tray

Label side up.

Notes

Audio CD

Data Disc

Total number of tracks Total recorded time of a disc

Total number of files

Display information in step 2

BASIC OPERATION

10 En

■ Playing back USB devices

Connect your USB device to the USB port on the

front panel. (For details, refer to page 8.)

When USB mode is selected (USB indicator lights up),

first filename is displayed in the front panel display (refer

to page 12), and playback starts automatically in order by

date and time of creation if playable files are in the USB

device.

To disconnect USB devices

Press to stop playback, and then disconnect the USB

device.

Do not disconnect your USB device while playing back from the

USB device, or when the USB indicator blinks.

Press e.

To resume playback, press e again (or press h).

Press s.

If you press h again, playback starts from the first track.

Press POWER again.

If you turn off the power when disc mode is selected, the

next time you turn the power on, playback starts

automatically of the disc on the tray. If you turn off the

power when USB mode is selected, playback will start

automatically of the USB device connected.

Select a desired track by using the numeric

buttons.

Example: To select track number 12

Press “1”, and then press “2”.

Following information is displayed.

Playback starts in 2 seconds.

This operation is not available for Data Disc and USB.

y

You can also select and playback a desired track during playback.

Press PURE DIRECT.

This unit is set to PURE DIRECT mode.

• The PURE DIRECT indicator lights up.

• The digital output is turned off.

• The front panel display is turned off and only the minimum

required indicators and messages are displayed during

playback.

Connect using the ANALOG OUT terminals when you use

PURE DIRECT mode (refer to page 7).

Note

Pausing playback

Stopping playback

USB

USBAudio CD Data Disc

Turning off the power

Playing back a desired track

Note

To improve audio quality (PURE

DIRECT mode)

Note

Audio CD

+

The selected track number

USBAudio CD Data Disc

English

BASIC OPERATION

11 En

OPERATION

y

• Press PURE DIRECT again to turn off PURE DIRECT mode.

• This setting is retained even if you turn off this unit.

To play back from the beginning of the next

track, press once.

To play back from the beginning of the current

track, press once.

To play back from the beginning of the previous

track, press twice.

y

• These operations can also be performed for Data Disc/USB.

• These operations can also be performed when the unit is

paused.

• These operations can also be performed using b/w and

f/a on the front panel.

To advance rapidly, press once during

playback.

To reverse rapidly, press once during

playback.

To resume playback, press at the desired

point.

y

• These operations can also be performed for Data Disc/USB.

• The sound can be heard (although slightly garbled) during these

operation in either direction. This is convenient for locating a

precise position within a track, or for reviewing the contents

quickly. Sound may not be heard depending on the MP3/WMA

file.

• Each time you press or , the search speed increases

by 2 levels.

• These operations can also be performed pressing and holding

b/w or f/a on the front panel for more than 2

seconds.

Skipping to the beginning of a

desired track

USBAudio CD Data Disc

Advancing or reversing playback

rapidly

USBAudio CD Data Disc

BASIC OPERATION

12 En

■ When playing back an Audio CD

You can select the following front panel displays (1 - 3) by pressing DISPLAY.

■ When playing back a Data Disc or USB device

You can temporarily display the filename by pressing DISPLAY.

These front panel display examples are for an MP3 file.

* 28 characters maximum

This unit can only show alphanumeric characters.

Press DIMMER to change the brightness level for

the front panel display.

Each time you press DIMMER, the brightness level

changes in the following order:

Max (brightest) J Level1 (default) J Level2 J Level3

(darkest) J Max

• Brightness is slightly decreased during playback, except when

the level is set to maximum.

• Brightness may temporarily be decreased for some operations,

except when the level is set to maximum.

• This setting is retained even if you turn off this unit.

Changing front panel display

Note

Audio CD

1 Elapsed time of the current track (Default)

2 Remaining time of the current track

3 Remaining time of the disc

USBData Disc

1 Elapsed time of the current track

2 Filename*

Returns to the normal display after displaying

a filename.

Changing the brightness of the front panel display

Notes

English

13 En

OPERATION

You can play back the tracks in random sequence.

To perform random-sequence play

Press , and then, RANDOM.

To cancel random-sequence play

Press .

These operations can also be performed for Data Disc/USB.

You can play back a single track or all tracks repeatedly

by pressing REPEAT during playback. The repeat

playback mode changes each time you press REPEAT.

S (Single repeat)

A single track is played back repeatedly.

ALL (Full repeat)

All tracks (the entire disc) are played back repeatedly.

These operations can also be performed for Data Disc/USB.

y

Repeat play also works for program play and random-sequence

play.

RANDOM-SEQUENCE PLAY

USBAudio CD Data Disc

+

Note

REPEAT PLAY

Repeating a selected item

USBAudio CD Data Disc

(Single repeat)

(Full repeat)

(off)

Note

REPEAT PLAY

14 En

You can repeat a specified section of a track by pressing

A/B during playback to set two points (start and end

points).

1 Press A/B to select the start point of repeat

play.

2 Press A/B to select the end point of repeat

play.

The selected section is played back repeatedly.

To cancel repeat A-B

Press A/B again to make “A-B” disappear from the front

panel display.

• You cannot set repeat A-B from one track to another track.

• This operation is not available for Data Disc and USB.

• If you stop playback by pressing , repeat A-B is canceled.

• You cannot use repeat A-B when this unit is in PURE DIRECT

mode.

Repeat A-B

Audio CD

“A-” lights up.

“A-B” lights up.

Notes

English

15 En

OPERATION

You can customize the playback order of up to 50 tracks

stored on an Audio CD. This operation is not available for

Data Disc and USB.

1 Press s to stop playback.

2 Press PROGRAM.

This unit is set to program input mode.

3 Program a desired track by pressing the

corresponding numeric button and ENTER.

Following information is displayed.

When you press “6”:

When you press ENTER:

Repeat this operation to program more tracks.

You can select the same track again.

Pressing PROGRAM in program input mode exits to normal

playback mode, though programmed tracks are stored.

4 Press h to start program play.

Following information is displayed.

PROGRAM PLAY

Audio CD

• In this mode, the front panel

display shows as normally, even

when this unit is in PURE

DIRECT mode.

+

Note

The selected track number

Total number of tracks

currently programmed

Total time of the tracks

currently programmed

Current track

Elapsed time of the

current track

PROGRAM PLAY

16 En

Press s.

To restart program play, press h after pressing

PROGRAM.

Playback starts from the first programmed track number.

There are several methods, as described below.

■ Clearing the last programmed track

Press CLEAR during program input mode.

Following information is displayed.

The last programmed track is cleared.

■ Clearing all programmed tracks

Press CLEAR after exiting program input

mode.

Following information is displayed.

All programmed tracks are cleared.

The display is turned off after 2 seconds.

Switching to USB mode, opening the disc tray or switching off

the POWER clears all programmed tracks.

Stopping program playback

Clearing programmed track

Note

Total number of the

tracks currently

programmed

Total time of the

tracks currently

programmed

Pagina se încarcă ...

Yamaha CD-S700 Manualul proprietarului

Yamaha CD-S700 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente