Yamaha MCR-640 Manualul proprietarului

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

RECEIVER/CD PLAYER

AMPLI-TUNER/LECTEUR CD

MCR

-

640

(R-840

+

CD-640

+

NS-BP300)

i

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou de

méthodes autres que ceux décrits ci-dessous, peuvent

entraîner une exposition à un rayonnement dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die Einstellung

bzw. die Ausführung von anderen als in dieser Anleitung

beschriebenen Vorgängen kann zu Gefährdung durch

gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande av

åtgärder på annat sätt än så som beskrivs häri kan resultera i

farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure non

specificati in questo manuale possono risultare in esposizione

a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos que

no se especifican enste manual pueden causar una exposición

peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of procedures

anders dan beschreven in dit document kan leiden tot

blootstelling aan gevaarlijke stralen.

ПРЕДОСТЕРЕЖЕНИЕ

Использование органов управления или произведение

настроек или выполнение процедур, не указанных в

данной инструкции, может отразиться на выделении

опасной радиации.

CD-640

DANGER:

CAUTION:

AVOID DIRECT EXPOSURE TO THE BEAM

INVISIBLE LASER RADIATION WHEN OPEN

DO NOT STARE INTO BEAM

INVISIBLE LASER RADIATION WHEN OPEN

CD-640

ii

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten

muutto saattaa altistaa vaaralliselle säteilylle tai muille

vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for

stråling.

Bemærk: Netafbryderen er sekundært indkoblet og ofbryder

ikke strømmen fra nettet. Den indbyggede netdel er derfor

tilsluttet til lysnettet så længe netstikket sidder i stikkontakten.

N

Observer: Nettbryteren er sekundert innkoplet. Den

innebygdenetdelen er derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för osynlig

laserstrålning, som överskrider gränsen för laserklass 1.

Observera! Strömbrytaren är sekundärt kopplad och inte bryter

inte strömmen från nätet. Den inbyggda nätdelen är därför

ansluten till elnätet så länge stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1

ylittävälle näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja

roiskevedelle.

Huom. Toiminnanvalitsin on kytketty toisiopuolelle, eikä se

kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on

kytkettynä sähköverkkoon aina silloin, kun pistoke on

pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA

EJ STRÅLEN.

iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place and away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the following

minimum clearances.

Top: 30 cm (R-840 Only)

Rear: 10 cm

Sides: 10 cm

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high

humidity (i.e. a room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp

the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. Yamaha will not

be held responsible for any damage resulting from use of this unit

with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable and

outdoor antennas disconnected from a wall outlet or this unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press to set it to standby mode and

disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the outlet,

then leave this unit alone.

19 When using this unit for a long time, this unit may become warm.

Turn the power off, then leave this unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug

can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

22 Excessive sound pressure from earphones and headphones can

cause hearing loss.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt to

service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam. When this unit is plugged into the wall

outlet, do not place your eyes close to the opening of the disc tray

and other openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit itself

is turned off by . This state is called standby mode. In this

state, this unit is designed to consume a very small quantity of

power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

The laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

LASER

Type Semiconductor laser GaAs/GaAlAs

Wave length 780 nm

Output Power 10 mW

1 En

English

PREPARATIONINTRODUCTION

TUNER

OPERATIONS

OTHER

OPERATIONS

ADDITIONAL

INFORMATION

BASIC

OPERATIONS

FEATURES ............................................................. 2

SUPPLIED ACCESSORIES ................................. 2

PLAYABLE DISC AND FILE FORMAT ............ 3

CONTROLS AND FUNCTIONS.......................... 4

Receiver (R-840)........................................................ 4

CD player (CD-640) .................................................. 5

Remote control........................................................... 6

PREPARATIONS ................................................... 8

Connecting speakers/external components/

antennas ................................................................. 8

Connecting power cables........................................... 9

Connecting an iPod™.............................................. 10

Connecting USB devices ......................................... 10

Installing the batteries in the remote control ........... 11

Using the remote control ......................................... 11

Adjusting the Clock ................................................. 12

SYSTEM OPERATIONS..................................... 13

Basic system operations........................................... 13

Changing the brightness of the front panel

display ................................................................. 14

Using headphones.................................................... 14

DISC AND USB DEVICE OPERATIONS......... 15

Playback operations................................................. 15

Switching the playback information display ........... 16

Repeating playback (Repeat Play)........................... 16

Repeating a specified section (Repeat A-B)............ 17

Playing back randomly (Random Play)................... 17

Customizing playback order (Program Play) .......... 17

FM TUNING......................................................... 18

Automatic tuning ..................................................... 18

Manual tuning.......................................................... 18

Automatic preset tuning........................................... 18

Manual preset tuning ............................................... 19

Selecting preset stations........................................... 19

RADIO DATA SYSTEM TUNING

(EUROPE MODEL ONLY)............................. 20

Displaying the Radio Data System information ...... 20

Using the TP (traffic program) data service ............ 21

CT (clock time) settings........................................... 21

SETTING THE TIMER .......................................22

Setting the clock timer............................................. 22

Setting the sleep timer ............................................. 23

SETTING THE AUTO-STANDBY MODE........24

CONTROLLING iPod™......................................25

Using iPod™ ........................................................... 25

TROUBLESHOOTING........................................26

Receiver (R-840)...................................................... 26

Remote control ........................................................ 28

CD player (CD-640) ................................................ 28

NOTES ABOUT HANDLING COMPACT

DISCS .................................................................30

GLOSSARY...........................................................30

Audio information ................................................... 30

Copyright and logo marks ....................................... 30

SPECIFICATIONS ...............................................31

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATIONS

TUNER OPERATIONS

OTHER OPERATIONS

ADDITIONAL INFORMATION

FEATURES

2 En

INTRODUCTION

Receiver (R-840)

• Minimum RMS output power per channel

65W + 65W (6Ω, 1kHz, 10% THD)

• 30-station FM preset tuning

• iPod playability (with rechargeable function)

• Pure Direct mode

• Adjustable Display Brightness

CD player (CD-640)

• Plays Audio CDs, MP3/WMA discs

• CD-R, CD-RW Disc Playability

• Plays MP3/WMA files stored on a USB device

• Linked operation with the receiver such as

Pure Direct mode, Adjustable Display

Brightness and INPUT mode

■ About this manual

• In this manual, “R-840” is described as “receiver” and “CD-640” is described as “CD player”.

• This manual describes how to operate the system using a remote control except when it is not available. Some of these operations are

also available using the front panel buttons.

• y indicates a tip for your operation.

• Notes contain important information about safety and operating instructions.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

This product includes the following accessories. Before connecting this system, make sure you received all of the following parts.

FEATURES

SUPPLIED ACCESSORIES

USB

Indoor FM antenna

Batteries (x2)

(AAA, R03, UM-4)

Remote

control

iPod dock cover*

USB cap*

* The USB cap and the iPod dock cover are supplied

with this product to cover the USB port and the

iPod dock when not in use.

iPod

INPUT

VOLUME

CD player

Receiver

System control

cable (0.6 m)

RCA stereo

cable (1.0 m)

CAUTION

Keep the USB cap out of the reach of children,

so that it is not mistakenly swallowed.

3 En

English

INTRODUCTION

■ Playable MP3 and WMA files (USB

device and Data Disc)

MP3

* Variable bitrate is also supported.

WMA

•Version 8

• Version 9 (Standard and variable bitrates are supported.

Professional and Lossless are not supported.)

* Variable bitrate is also supported.

Notes

• Playback for Data Disc starts in alphanumeric order.

• Playback for USB starts in order by date and time of creation.

• Copyright-protected WMA (DRM) files cannot be played back

by the CD player.

• The disc must be ISO 9660 compatible.

• Elapsed time may not be displayed correctly while playing back

variable bitrate contents.

* The root is counted as one of the folders.

■ Playable discs

Use compact discs bearing the marks below.

To play back an 8-cm (3-inch) CD

Place it in the inner recessed area of the disc tray. Do not

put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.

PLAYABLE DISC AND FILE FORMAT

Format

Bitrate

(kbps)

Sampling

frequency

(kHz)

MPEG 1 Audio Layer-3 32-320 * 32/44.1/48

MPEG 2 Audio Layer-3, 2 8-160 * 16/22.05/24

MPEG-2.5 Audio Layer-2 8-160 * 8/11.025/12

Profile

Bitrate

(kbps)

Sampling

frequency

(kHz)

High Profile 32-320 * 32/44.1/48

Mid Profile 16-32 16/22.05

Data Disc USB

Maximum total number of file

and folder*

512 999

Maximum folder number* 255 255

Maximum file number per

folder

511 255

....

Compact discs (digital audio)

....

CD-R, CD-RW digital audio discs

• CD-R or CD-RW discs bearing one of

the following phrases.

FOR CONSUMER

FOR CONSUMER USE

FOR MUSIC USE ONLY

• Finalized CD-R or CD-RW discs.

Note

The CD player may not be able to play some

CD-R/CD-RW discs or discs on which

recording was not made correctly.

To prevent a malfunction of this unit:

• Do not use any nonstandard

shaped disc (heart, etc.) available

on the market because it might

damage the unit.

• Do not use a disc with tape, stickers, or paste on it. If

you use such a disc, the disc may get stuck in the

unit, or damage to the unit may result.

Note: Do not use any lens cleaners as they may be a

cause of malfunction.

CONTROLS AND FUNCTIONS

4 En

■ Front panel

1 INPUT

Selects an input source.

2 On/Standby indicator

Lights up in green when the receiver is turned on. Lights

up in amber when the receiver is in standby mode.

3 TP indicator

Lights up when the receiver is receiving a Radio Data

System station which contains the TP (Traffic Program)

data service (☞p.21).

4 Remote control sensor

Receives signals from the remote control.

5 PRESET indicator

Lights up when you select preset radio stations (☞p.19).

6 TUNED indicator

Lights up when the receiver is tuned into a station.

7 STEREO indicator

Lights up when the receiver is receiving a strong signal

from an FM stereo broadcast.

8 SLEEP indicator

Lights up when the sleep timer is on (☞p.23).

9 Front panel display

Shows the various information such as the tuning

frequency.

0 VOLUME

Adjusts the volume level.

A (On/Standby)

Turns the receiver on or sets it to standby mode.

B PHONES jack

Outputs audio signals for private listening with

headphones.

C TIMER indicator

Lights up when the timer is set (☞p.22).

D BASS

Adjusts the low frequency response (☞p.13).

E TREBLE

Adjusts the high frequency response (☞p.13).

F BALANCE

Adjusts the audio output balance of the left to right

speakers to compensate for imbalances caused by speaker

locations or listening room conditions.

G PRESET d / u

Selects a preset station. The input source is changed to

FM. Operable even when the receiver is in standby mode

(☞p.19).

H PURE DIRECT

Turns on or off Pure Direct mode (☞p.13).

When Pure Direct mode is on, the indicator lights up in

blue.

I h / e

Starts and pauses the playback of iPod. The input source is

changed to iPod. Operable even when the receiver is in

standby mode.

J iPod dock

Connect your iPod (☞p.10).

CONTROLS AND FUNCTIONS

Receiver (R-840)

INPUT

BASS

PHONES

VOLUME

MIN MAX

TREBLE BALANCE

PRESET PURE DIRECT

LR

PRESET

TP

TUNED

STEREO SLEEP

kHz MHz

iPod

TIMER

1

@

IJBCD E F G H

234 5 67 98

A

Top viewFront view

5 En

CONTROLS AND FUNCTIONS

English

INTRODUCTION

■ Front panel

1 USB port

Connect your USB device.

2 p (play) indicator

Appears during playback.

3 CD indicator

Appears when an audio CD is loaded.

4 Music data type indicator

Indicates the type of music data stored on the disc in the

disc tray or on the USB device connected to the USB port.

5 Time display mode indicators

Indicate the kind of time information displayed on the

front panel display (☞p.16).

6 PROG indicator

Lights up when Program play mode is selected.

7 RANDOM indicator

Lights up when Random play mode is selected.

8 REP OFF S ALL A-B indicator

Lights up when Repeat play mode is selected.

9

Returns to the beginning of the current track. Press and

hold to fast reverse. Press twice to skip to the previous

track (☞p.15).

0

Starts or pauses playback (☞p.15).

When this button is pressed during standby mode, the

receiver automatically turns on and the input source

changes to either CD or USB, whichever was last selected.

A

Skips to the next track. Press and hold to fast forward

(☞p.15).

B (On/Standby)

Turns on the CD player or sets it to standby mode.

When this button is pressed during standby mode, the

receiver automatically turns on and the input source

changes to either CD or USB, whichever was selected last.

C e (pause) indicator

Lights up while the CD player is paused.

D Disc tray

Holds a disc to be played back.

E Front panel display

Shows the current status of the CD player.

F

Opens and closes the disc tray.

When this button is pressed during standby mode, the

receiver automatically turns on and the input source

changes to CD.

G

Stops playback (☞p.15).

CD player (CD-640)

USB

PROG RANDOMCD MP3 WMA TRACK TOTAL REMAIN REP OFF S ALL A-B

1

@

BCDE

234 5

7

98

A

6

F

G

6 En

CONTROLS AND FUNCTIONS

This remote control can operate the system components

(including tuner functions) and an iPod stationed in the

iPod dock on the top of the receiver.

To operate the CD player, tuner functions, or an iPod

using the remote control, you need to set the receiver to

corresponding input mode (☞8Input selection keys).

To operate your iPod

Press the corresponding iPod operation key on the remote

control.

The iPod operation keys are indicated with in the

section below. See page 25 for more information on the

operation of your iPod.

1 Infrared signal transmitter

Sends signals to the system you want to control.

2 (On/Standby)

Turns the system on or sets it to standby mode.

3 MENU

Returns to the upper level in the iPod menu.

4

Skips to the next song. Press and hold to fast forward.

5

Skips to the beginning of the current track. Press twice to

skip back to the previous track. Press and hold to fast

reverse.

6 ENTER

Press ENTER to enter the selected group. (Pressing

ENTER starts playback when a song is selected.)

7

Starts or Pauses Playback.

8 Input selection keys

Select the input source on the receiver.

When selecting an input source, press the corresponding

input selection key (or turn INPUT on the front panel).

The name of the corresponding input source appears on

the front panel display of the receiver.

y

When CD or USB is selected as an input source, the CD player

turns on automatically and when other input source is selected,

the CD player sets to standby mode.

9 MEMORY

Stores a preset station in the memory (☞p.19). Starts

Automatic preset tuning (☞p.18).

0 TP

Enters TP (Traffic Program) data service receiving mode

(☞p.21).

Remote control

1

M

N

O

P

Q

R

S

t

U

V

W

X

Y

Z

[

\

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

7 En

CONTROLS AND FUNCTIONS

English

INTRODUCTION

A MONO

Sets FM broadcasting receiving mode to monaural mode.

B DISPLAY

Switches the information shown on the front panel display

of the receiver and CD player (☞p.16, p.20).

C OPTION

Enters option menu mode.

See pages 19, 21 and 24 for option menu items.

D , , , , ENTER

For selecting and confirming an item.

E

Pauses playback (☞p.15).

F

Stops playback (☞p.15).

G ,

Rewind and fast-forward music.

H Numeric keys

Input numbers.

I PROGRAM

Sets the CD player to the track program mode (☞p.17).

J RANDOM

Turns on/off the Random Play (☞p.17).

K TIMER

Shows the current time on the front panel display of the

receiver.

And sets the clock (☞p.12) or the timer (☞p.22).

L SLEEP

Sets the sleep timer on the system (☞p.23).

M

Opens and closes the disc tray.

N ,

Press or to switch an item in the selected group

(☞p.25).

O SHUFFLE

Selects mode of Shuffle Play (☞p.25).

P REPEAT

Selects mode of Repeat Play (☞p.25).

Q TUNING

Press TUNING for manual tuning and press and

hold TUNING for automatic tuning (☞p.18).

R PRESET u / d

Selects a preset station (☞p.19).

S PURE DIRECT

Turns on or off Pure Direct mode (☞p.13).

T VOLUME +/–

Adjusts the overall volume level on the receiver.

U

Starts playback (

☞p.15).

V MUTE

Turn off the volume (☞p.14).

W ,

Skips to the beginning of the current track or next track.

X CLEAR

Clears an entry.

Y ENTER

Confirms an entry.

Z A-B

Sets start and end points of a section and plays back the

specified section repeatedly (☞p.17).

[ REPEAT

Selects the Repeat Play mode (☞p.16).

\ DIMMER

Changes the brightness of the front panel display (☞p.14).

/

d

/

d

/

d

PREPARATIONS

8 En

PREPARATION

Make sure you read the following procedure and note carefully before connecting the system. The remote control

and linked operation of the system only work when the receiver and the CD player are connected via

the system control cable. For information on the speakers (NS-BP300), refer to the owner’s manual supplied with it.

Connecting the system

1 Connect the AUDIO IN ( PLAYER L/R) jacks of the receiver to the AUDIO OUT ( L/R) jacks of the CD player

using the supplied audio RCA stereo cable.

2 Connect the SYSTEM CONNECTOR ( TO:PLAYER) jack of the receiver to the SYSTEM CONNECTOR

( TO:RECEIVER) jack of the CD player using the supplied system control cable.

3 Connect the speaker terminals (L) of the receiver to the speaker terminals of the left speaker and the speaker terminals

(R) of the receiver to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set

(NS-BP300).

4 Connect the supplied FM antenna to the ANTENNA jack.

• Do not connect this unit or other components to the main power until all connections between components are complete.

• Do not let the bare speaker wires touch each other or any metal part of the receiver. This could damage the receiver and/or the

speakers.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be

heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also,

refer to the owner’s manual for each of your components.

Notes

• The system control connection is used to transmit the remote control signals from the receiver to the CD player.

• When connecting speakers other than NS-BP300, use speakers having more than 6Ω impedance.

• If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use

commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.

PREPARATIONS

Connecting speakers/external components/antennas

CAUTION

A A

B

Receiver (R-840)

(Europe model)

CD player (CD-640)

Left speaker

(NS-BP300)

Right speaker

(NS-BP300)

RCA stereo cable

(supplied)

System control cable

(supplied)

DVD player etc.

Subwoofer

Audio

out

RCA

stereo

cable

PREPARATIONS

9 En

English

PREPARATION

After you made all connections, connect the power cables of this system and other components to AC wall outlets.

Connecting power cables

To AC wall outlet

CD player (CD-640)

Receiver (R-840)

PREPARATIONS

10 En

The receiver is equipped with the iPod dock on the top

panel where you can station your iPod and control

playback of your iPod using the supplied remote control.

Use this receiver with iPod dock adapter (supplied with

your iPod or commercially available) appropriate for your

iPod. If you use this receiver without using an appropriate

iPod dock adapter, loose connection may result.

y

When the receiver is turned on or in standby mode, connect the

iPod during the playback. The receiver automatically starts

playback of iPod (for the fifth or later generation of iPod, iPod

touch, iPod Classic, or iPod nano).

Notes

• Only iPod (Click and Wheel), iPod nano, iPod Classic, iPod

mini and iPod touch are supported.

• Do not connect any iPod accessories (such as headphones, a

wired remote control, or an FM transmitter) to your iPod when

it is stationed in the iPod dock.

• Unless your iPod is firmly stationed in the iPod dock, audio

signals may not be output properly.

• Once the connection between your iPod and the receiver is

complete and the receiver is set to iPod mode (☞p.6),

“CONNECTED” appears on the front panel display. If the

connection between your iPod and the receiver fails, a status

message appears on the front panel display. For a complete list

of connection status message, see the iPod section in

“TROUBLESHOOTING” (☞p.26).

• When your iPod is stationed in the iPod dock of the receiver,

your iPod can be charged automatically even when the receiver

is in standby mode.

• You can disconnect the iPod during the playback.

This CD player has a USB port and can access MP3 or

WMA files saved on your USB device. Connect your USB

device to the USB port on the front panel of the CD

player.

■ Supported USB devices

This CD player supports USB mass storage class devices

(e.g., flash memories, card readers or portable audio

players) using FAT16 or FAT32 format.

Notes

• Some devices may not work properly even if they meet the

requirements.

• Do not connect devices other than the USB mass storage class

devices.

• When you insert two or more memory cards at the same time

using card readers, etc., only one of the memory cards is

recognized.

• Yamaha and suppliers accept no liability for the loss of data

saved on the USB devices connected to the receiver. As a

precaution, it is recommended that the files are made backup

copies.

• Playability of and power supply to all kind of USB devices are

not guaranteed.

• When your USB device is connected to the USB port, your

USB device can be charged automatically even when the CD

player is in standby mode. Some USB devices cannot be

charged in standby mode.

• You can disconnect the USB device during the playback.

Connecting an iPod™

iPod

INPUT

PHONES

BASS

-+ -+ LR

TREBLE BALANCE

PRESET PURE DIRECT

VOLUME

MIN MAX

Receiver

iPod

iPod dock adapter

Connecting USB devices

USB

CD player

USB device

PREPARATIONS

11 En

English

PREPARATION

■ Notes on batteries

• Change both batteries when the operation range of the

remote control decreases.

• Use AAA, R03, UM-4 batteries.

• Make sure that the polarities are correct. See the

illustration inside the battery compartment.

• Remove the batteries if the remote control is not to be

used for an extended period of time.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean the

battery compartment thoroughly before installing new

batteries.

• Do not throw away batteries with general house waste;

dispose of them correctly in accordance with your local

regulations.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of the receiver during

operation.

Notes

• The area between the remote control and the receiver must be

clear of large obstacles.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– high humidity, such as near a bath

– high temperature, such as near a heater or a stove

– extremely low temperatures

– dusty places.

• Do not expose the remote control sensor to strong lighting, in

particular, an inverter type fluorescent lamp; otherwise, the

remote control may not work properly. If necessary, position the

system away from direct lighting.

Installing the batteries in the

remote control

1

3

2

Using the remote control

INPUT

BASS

PHONES

VOLUME

MIN MAX

TREBLE BALANCE

PRESET PURE DIRECT

LR

30˚ 30˚

Within 6 m

(20 feet)

Receiver (R-840)

PREPARATIONS

12 En

Before starting playback operation, follow the procedure

below to adjust the clock setting of the receiver.

Notes

• Use the remote control to set the clock. You cannot set the clock

with the buttons on the receiver.

• The receiver supports 24-hour clock display.

• If you do not touch any key for 90 seconds, the receiver returns

to normal mode.

1 Press to turn the receiver on.

The front panel display lights up.

2 Press TIMER to show the current time.

If the clock is not set, “SET TIME” flashes on the

display.

Press ENTER to proceed to step 3.

3 Press / to select “TIME”, and press

ENTER.

The receiver enters clock setting mode. The hour

digits start flashing.

4 Set the hour using / , and press .

The minute digits start flashing.

5 Set the minutes using / , and press

ENTER.

The hour and minute digits start flashing.

To change the hour or minutes again, press or ,

do steps 4 and 5, and proceed to step 6.

6 Press ENTER.

The clock is set.

The hour and minute segments stop flashing and

remain on. The receiver returns to the normal mode.

y

You can return to the previous screen by pressing .

Adjusting the Clock

TIMER

ENTER

,

Flashes

SYSTEM OPERATIONS

13 En

English

BASIC

OPERATIONS

BASIC OPERATIONS

Follow the procedure below to select an input source and adjust the sound settings on the system.

1 Press (On/Standby) to turn on the receiver.

Depending on the input mode of the receiver, the CD

player also turns on by the system control connection

(☞p.8). The front panel display lights up.

y

This system has an auto-standby function (☞p.24) which

automatically sets it to standby mode if not operated for

30 minutes while the receiver is set to CD or USB input mode.

2 Press one of the input selection keys (or

rotate INPUT on the front panel) to select the

desired input source.

3 Start playback on the selected source

component or select a radio station.

For information on the disc/USB device playback,

see page 15, and for information on tuning, see

page 18.

4 Press VOLUME +/– (or turn VOLUME on the

front panel) to adjust the volume to the

desired output level.

5 Rotate BASS, TREBLE, or BALANCE on the

front panel of the receiver to adjust the

following settings.

BASS: Adjusts the low frequency response.

TREBLE: Adjusts the high frequency response.

BALANCE: Adjusts the volume level of each left

and right speaker channel.

■ Pure Direct mode

Pure Direct mode bypasses the tone control circuit and

turns off the front panel display, allowing you to enjoy

pure high-fidelity sound.

Press PURE DIRECT (or PURE DIRECT on the

front panel) to turn on Pure Direct mode.

The front panel display automatically turns off. PURE

DIRECT on the front panel is backlit in blue.

Notes

• If you carry out operations while Pure Direct mode is turned on,

the front panel display lights up briefly to acknowledge the

command.

• While the Pure Direct mode is turned on, neither BASS,

TREBLE, nor BALANCE is available.

SYSTEM OPERATIONS

INPUT

BASS

PHONES

VOLUME

MIN MAX

TREBLE BALANCE

PRESET PURE DIRECT

LR

TP

TIMER

USB

INPUT

(On/Standby) VOLUME

PURE

DIRECTBASS BALANCE

TREBLE

(On/Standby)

VOLUME +/–

Input selection

keys

PURE DIRECT

MUTE

Basic system operations

SYSTEM OPERATIONS

14 En

To turn off Pure Direct mode

Press PURE DIRECT again. The PURE DIRECT

backlight turns off and the front panel display turns on.

■ Muting the sound (MUTE)

Press MUTE to reduce the current volume level

by approximately 20dB.

“MUTE ON” appears on the front panel display.

Press MUTE again to restore the audio output to the

previous volume level.

You can dim the front panel display of the receiver. The

front panel display of the CD player also dims by the

system control connection (☞p.8). (The default setting is

“DIMMER OFF”.)

Press DIMMER.

You can choose your desired brightness of the front panel

display between normal (bright), mid dim, and dim.

You can connect your headphones to the PHONES jack on

the front panel of the receiver.

The sound from the speakers and the subwoofer stops.

Changing the brightness of the

front panel display

Using headphones

DIMMER

INPUT

PHONES

DISC AND USB DEVICE OPERATIONS

15 En

English

BASIC

OPERATIONS

You can enjoy playing back your audio CDs, and MP3 or WMA files recorded on a disc/USB device. Some operations

may be different or restricted depending on the disc/USB device. Before playing back, check the compatibility of your

disc/USB device with this system (☞p.3).

■ To start disc playback

1 Select CD as an input source (☞p.13).

2 Press to open the disc tray and load a

CD.

3 Press .

Playback starts automatically.

For an audio CD, playback starts from the first track,

and for MP3 or WMA files, playback starts in

alphanumeric order by the filename.

y

You can also close the disc tray by pressing on the front

panel of the CD player.

■ To start USB device playback

1 Select USB as an input source (☞p.13).

2 Connect your USB device to the USB port on

the CD player.

The total number of files are displayed.

The reading time may exceed 30 seconds depending

on the number of files/folders.

3 Press to start playback.

The files are played back in the sequence of the date

and time created.

Notes

• Total time does not appear for USB device playback.

• If the USB device is partitioned, only the first partition is

displayed.

• Some files may not work properly depending on the USB

device specification.

• Copyright-protected files cannot be played back.

• This system can play back files of 4 GB in size or less.

To stop playback

Press .

For audio CD, the total track number and total time of the

disc are displayed and for MP3/WMA disc or USB device,

the total file number is displayed on the front panel.

To pause playback

Press .

To return to normal playback, press .

To skip tracks

• To return to the start of the current track, press .

• To skip to the next track, press .

• To skip to the previous track, quickly press twice.

To fast reverse or fast forward

• To fast reverse, press .

• To fast forward, press .

To return to normal playback, press .

y

Only a low sound is heard during fast-reverse or fast-forward.

DISC AND USB DEVICE OPERATIONS

Playback operations

,

USB

CD

,

DISC AND USB DEVICE OPERATIONS

16 En

You can switch the disc playback information shown in

the CD player’s front panel display. Available information

differs depending on the type of the disc/USB device.

Press DISPLAY repeatedly while playing back a

disc/USB device.

Each time you press the key, the information display

changes as described in “Playback information for audio

CDs” and “Playback information for MP3 or WMA files

recorded on discs/USB devices”.

Notes

• Some information may not be available depending on a disc/

USB device.

• Some special characters may not be shown properly.

■ Playback information for audio CDs

The following information can be displayed during

playback of an audio CD.

■ Playback information for MP3 or WMA

files recorded on discs/USB devices

The following information is available during playback of

an MP3 or WMA disc/USB device.

Note

After a file name is displayed for a few seconds, the screen

automatically returns to the elapsed time display.

You can play back a single track or all tracks on a disc/

USB device repeatedly.

1 Play back the disc/USB device you want to

repeat.

2 During the playback of the disc/USB device,

press REPEAT to select the desired Repeat

Play mode.

Each time you press the key, the Repeat Play mode

indicator in the CD player’s front panel display

changes as follows.

To cancel Repeat Play

Press REPEAT repeatedly so that the Repeat Play mode

indicator disappears from the front panel display.

Note

The Repeat play mode is canceled when the disc/USB device is

removed.

y

“REP OFF” appears when the system is set to Pure Direct mode.

Switching the playback

information display

DISPLAY

1Elapsed time of the current track (Default)

2Remaining time of the current track

3Remaining time of the disc

1Elapsed time of the current file

2File name

Repeating playback

(Repeat Play)

REPEAT

Off (Normal playback)

REP S (Repeat Play by the current track)

REP ALL (Repeat Play by disc/USB)

Pagina se încarcă ...

Yamaha MCR-640 Manualul proprietarului

Yamaha MCR-640 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente