Yamaha VS-10 Manual de utilizare
- Categorie
- Receptoare AV
- Tip
- Manual de utilizare
VS-10
POWER
STANDBY
NATURAL SOUND HOME THEATER SYSTEM VS-10
OPEN
DIGITAL
DIGITAL
DOLBY
SURROUND
OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
VS-10
Home Theater Sound System
Systèm audio home cinéma
UCA
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the manufac-
turer, or sold with the apparatus. When a
cart is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION
INTRODUCTIOIN
PREPARATIONS
PLAYBACK
SETUP MENU APPENDIX
English
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation instruc-
tions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regula-
tions, Part 15 for Class “B” digital devices. Compliance
with these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line filter/
s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to coaxial type
cable.
If these corrective measures do not produce satisfac-
tory results, please contact the local retailer autho-
rized to distribute this type of product. If you can not
locate the appropriate retailer, please contact Yamaha
Electronics Corp., U.S.A. 6660 Orangethorpe Ave,
Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
IMPORTANT SAFETY INSTRUCTIONS
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume
levels.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, and
clean place with at least 10 cm above, behind and on
the both sides of this unit - away from direct sunlight,
heat sources, vibration, dust, moisture, and/or cold.
3 Position this unit away from other electrical
appliances, motors and transformers to avoid
humming sounds, do not place this unit where it may
get exposed to rain or any kind of liquid to prevent
fire or electrical shock.
4 Avoid extreme temperature swings or excessive use
of humidifier in the room where this unit is installed
to prevent condensation inside this unit, which may
cause an electrical shock, fire damage to this unit,
and/or personal injury.
5 Do not cover this unit with a newspaper, a tablecloth,
a curtain, etc. in order not to obstruct heat radiation.
If the temperature inside this unit rises, it may cause
fire, damage to this unit and/or personal injury.
6 Avoid installing this unit in a place where foreign
objects and liquid might fall. It might cause a fire,
damage to this unit and/or personal injury. Do not
place the following objects on this unit:
• Other components, as they may cause damage
and/or discoloration on the surface of this unit.
• Burning objects (i.e., candles), as they may cause
fire, damage to this unit and/or personal injury.
• Containers with liquid in them, as they may cause
an electrical shock to the user and/or damage to
this unit.
7 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
8 When moving this unit, be sure to first disconnect the
power cord from the AC outlet and disconnect all
cords connecting this unit to other equipment.
9 Do not use force on switches, controls or connection
cables. Never pull the cables when disconnecting
them.
10 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may result in fire or other accidents.
YAMAHA will not be held responsible for any damage
resulting from the use of this unit with a voltage other
than that specified.
11 Do not attempt to clean this unit with chemical
solvents; this might damage the finish. Use a clean,
dry cloth.
12 Disconnect the power cord from the wall outlet when
not planning to use this unit for a long period of time,
or during an electrical storm, as they may cause
damage by lightning.
13 Do not attempt to modify or fix this unit. Contact the
qualified YAMAHA service personnel when any
service is needed. Cabinet should never be opened
for any reasons.
14 Be sure to read ‘TROUBLESHOOTING’ section
regarding common operating errors before
concluding that this unit is faulty.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
• The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows:
The wire which is coloured BLUE must be connected to
the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured BROWN
must be connected to the terminal which is marked with
the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
1
English
PREPARATION
REMOTE CONTROL
APPENDIX
PREPARATION
OPERATION
FEATURES
● Home Theater Sound
This system delivers a realistic and powerful sound
experience like that found in a movie theater just by
connecting the VS-10 to the TV. You can also enjoy
stronger bass and surround effects by adding the
separately available YAMAHA NX-SW10, consisting
of a subwoofer, a center speaker and two rear
speakers.
● Includes Dolby Digital, Dolby Pro
Logic and DTS Decoders
This system can reproduce the sound field of the
software with the g, s or
logo mark.
● Virtual Surround (available for Virtual
Dolby Digital)
The VS-10 can produce a virtual surround sound field
when playing software with the g,
s or logo mark so that you can
enjoy surround effects that give a motion to sound and
make you feel like you are in action.
● Eight DSP programs including
YAMAHA CINEMA DSP
Connecting the YAMAHA NX-SW10 (sold
separately) allows eight different DSP programs to be
used to enhance the power and realism of various
sources, from movies to concerts, sporting events and
games. Moreover, the SILENT CINEMA program
allows you to enjoy Virtual Surround by connecting
the headphones.
● Preset Remote Control
The remote control can be used to control not only the
control center, but component from other
manufacturers merely by setting the proper
manufacturer code.
PREPARATION
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works.
©1992 – 1997 Dolby Laboratories, Inc. All rights
reserved.
CONTENTS
y indicates a tip for your operation.
APPENDIX
GLOSSARY................................................................ 31
TROUBLESHOOTING ............................................ 32
SPECIFICATIONS.................................................... 33
INDEX ........................................................................ 34
REMOTE CONTROL
OPERATING OTHER COMPONENTS USING
THE REMOTE CONTROL .................................. 27
OPERATION
OPERATING THE UNIT ......................................... 17
USING CONVENIENT FUNCTIONS .................... 19
DSP PROGRAM (DIGITAL SOUND FIELD
PROCESSOR EFFECT)........................................ 21
MENU FUNCTIONS................................................. 24
PREPARATION
FEATURES .................................................................. 1
GETTING STARTED ................................................. 2
NAMES OF ALL PARTS ............................................ 4
SPEAKER PLACEMENT .......................................... 6
INSTALLATION ......................................................... 7
CONNECTIONS.......................................................... 9
ADJUSTING THE SPEAKER
OUTPUT LEVELS ................................................. 15
Manufactured under license from Digital Theater
Systems, Inc. US Pat. No. 5,451,942 and other world-
wide patents issued and pending. “DTS”, “DTS Digital
Surround”, are trademarks of Digital Theater Systems,
Inc. Copyright 1996 Digital Theater Systems, Inc. All
Rights Reserved.
2
Connecting to a TV (monitor), DVD player, Satellite tuner and VCR
TV (monitor)
VIDEO
OUT
AUDIO
OUT
L
R
DVD player
VIDEO
OUT
OPTICAL DIGITAL
OUTPUT
Satellite tuner
VIDEO
OUT
AUDIO
OUT
L
R
VCR
Control center VS-10 (rear panel)
VIDEO
IN
AUDIO
IN
L
AUDIO
OUT
R
1
2
Audio connection cord (2 pin) (x 1)
Supplied cords
Commercially available cable
Optical fiber cable
Video connection cord (x 1)
R
L
V
R
L
V
Connection Guide
DIGITAL 1
(V/PCM)
VIDEO 1 TV
VIDEO SIGNAL
INPUT
MAIN SPEAKERS
SUBWOOFER
OUT
MONITOR
OUT
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
+
+
–
V RL
V RL
V RL
VV R L
V
V
V
R L
R L
■ Inserting the batteries
1 Remove the battery compartment cover.
2 Insert the four batteries (AAA, R03, UM-4 type)
with + and – oriented properly.
3 Close the battery compartment cover.
■ Precautions regarding batteries
Misuse of dry cell batteries may result in leakage or
bursting. Be sure to follow the precautions given below.
• Insert batteries with (+) and (–) oriented according to the
marking in the battery compartment.
• Do not mix old and new batteries.
• Do not mix different types of batteries as they may offer
different voltage and performance even though they have
the same shape.
• Remove all batteries when they can no longer be used or
when the remote control will not be used for an extended
period.
• Do not use rechargeable batteries.
• If leakage occurs, wipe away all battery fluid inside the
compartment.
Preserving the manufacturer code
Replace batteries early before they become unusable.
The manufacturer code set by the user will be preserved
for about two minutes when batteries run out or when
they are removed. Note that the manufacturer code
setting may be lost if more than two minutes elapses.
Readying the Remote Control
Connection guide
Audio connection cord
(2 pin, 1.5 m)
Batteries (AAA, R03, UM-4 type)Remote control
GETTING STARTED
Checking the Package Contents
Check that the following accessories are included in the package.
Video connection cord (1.5 m)
Installation attachments
for the control center
EFFECT
DSP
SET
AVMUTE
TEST
SUBWOOFER
+
SUBWOOFER
–
NIGHT MODE
231
564
8
MENU
97
0
+–
ENTER
LAST
–
VOL VOL
+
VS10 TV VCR CBL
ON/OFF
CH
CH
MEMORY
Supporting stand
Bottom pads (x 4)
Side pads (x 2)
3
English
PREPARATION
POWER
STANDBY
NATURAL SOUND HOME THEATER SYSTEM VS-10
OPEN
DIGITAL
DIGITAL
DOLBY
SURROUND
■ Battery replacement cycle
Replace all four batteries when the operational range of the
remote control starts to become shorter.
■ Precautions on handling the
remote control
• The remote control may not be able to operate the
control center when an object blocks the remote control
sensor on the unit.
• Do not subject the remote control to impact. Do not
allow it to get wet or place it in a location subject to high
humidity.
• The remote control operations become difficult when
direct sunlight or other strong light (such as from an
inverter fluorescent lamp) strikes the sensor. Adjust the
relative positions of the light and the control center if
this happens.
• Remote control operations may not be possible if another
remote control is being operated at the same time.
30°30°
Approx. 20 cm – 6 m
Control center
Operational Area of the Remote Control
GETTING STARTED
4
NAMES OF ALL PARTS
Control Center (Front Panel)
POWER
STANDBY
PHONES
INPUT
SILENT
DIGITAL2 VIDEO2
DSP VOLUME
POWER
NATURAL SOUND HOME TH
E
OPEN
DSP selector button (page 22)
VOLUME N/B (page 17)
INPUT selector
button (page 17)
STANDBY indicator
When this indicator lights up,
this unit consumes a very
small quantity of power to
receive infrared-signals from
the remote control.
VIDEO 2 audio input
terminals
DIGITAL 2 optical
digital input terminal
PHONES jack
Used to connect the headphones.
No sound can be heard from the
speakers when the headphones are
connected.
POWER (page 17)
Turns the power of the control
center on and off. This button
also turns off the subwoofer’s
power when the YAMAHA NX-
SW10 (sold separately) is
connected. The STANDBY
indicator lights when power is
turned off using p on the
remote control.
Processing indicators (page 23) VIRTUAL indicator Phones indicator
Lights when the headphones are connected.
EFFECT OFF indicator
Lights when the sound field
effects is not turned on.
TRUBASS indicator (page 19)
Shows the various information such as DSP
program name, level or operational status
To open the front door
Press downward “OPEN” on the left
bottom of the front door. When the
parts inside the front door are not used,
put the front door back.
Display
As the display becomes brighter for a few seconds each time this unit is operated, you can check the current operation clearly.
DIGITAL 2 / VIDEO 2
video input terminal
5
English
PREPARATION
Remote Control
Not used with this unit. (page 30)
TEST (page 15)
SUBWOOFER + (page 19)
MENU + (page 24)
Numeric buttons (page 27)
AV selector button (page 17)
CH
g
(page 27)
VOL + (page 17)
Not used with this unit.
(pages 29 and 30)
Transmission indicator
EFFECT ON/OFF (page 23)
t (page 19)
NIGHT MODE (page 19)
SUBWOOFER – (page 19)
MENU – (page 24)
MENU (page 24)
SET/DSP (pages 22 and 27)
MUTE (page 19)
VOL – (page 17)
Remote control selector buttons
(page 27)
p
(power) (page 17)
EFFECT
DSP
SET
AVMUTE
TEST
SUBWOOFER
+
SUBWOOFER
–
NIGHT MODE
231
564
8
MENU
97
0
+–
ENTER
LAST
–
VOL VOL
+
VS10 TV VCR CBL
ON/OFF
CH
CH
MEMORY
MEMORY (page 20)
NAMES OF ALL PARTS
6
■ Main speakers NX-VS10M
Place the main speakers an equal distance from each side of
the TV monitor.
Placing the main speakers at almost the same height as your
listening position is more effective.
■ YAMAHA center speaker
NX-VS10C (sold separately)
Place the center speaker on top of the television and align
the front surface of the speaker with the front surface of the
television monitor. If the speaker cannot be placed on top of
the television, place it on a rack beneath the television as
close to the television monitor as possible.
■ YAMAHA rear speakers NX-VS10E
(sold separately)
Depending on room conditions, it is possible to place
YAMAHA rear speakers NX-VS10E on shelves or hang
them on the wall. Speakers should be placed about 1.5 m
above the floor when you sit on the floor, or about 1.8 m
above the floor when you sit on the chair.
■ YAMAHA subwoofer SW-VS10
(sold separately)
Place the subwoofer at the outside of the either right or left
main speaker and turn it slightly toward the center of the
room to reduce the wall reflections. Try altering the position
of the subwoofer versus the listening position as the relative
position will affect the way the bass sounds.
CAUTION
Although these main speakers are magnetically shielded,
they may still affect the color on the television monitor
when using the speakers near the television. Adjust the
relative positions of the speakers and the television if this
happen. Perform the following steps if you are using a
magnetically shielded television.
1 Turn off the television.
2 Wait awhile and turn the television back on.
You can also use the screw holes on the bottom of the main
speakers for installing the speakers on commercially
available speaker stands.
SPEAKER PLACEMENT
Although speakers should ideally be placed as shown below, satisfactory effects may be obtained even if you do not strictly
follow these guidelines.
1.5 - 1.8 m
Right rear
speaker
Rear speakers (sold separately)
Place behind or to the sides of the listening position.
Left rear
speaker
Subwoofer (sold separately)
Place near the right or left main speaker.
Center speaker (sold separately)
Place above the TV monitor in the center.
Main speakers
Place in each side of the TV monitor.
About 1.8 mAbout 1.5 m
When sitting on the floor. When sitting on the chair.
60 mm
A screw with a diameter of 4 mm can be used.
(Hole depth: 8 mm)
7
English
PREPARATION
INSTALLATION
Depending on room conditions, the control center can be installed vertically or horizontally.
Precautions before installation
• Do not touch the adhesive surface after peeling off the pad as this will weaken its adhesive strength.
• Thoroughly wipe clean the surface where the pad is to be applied. Note that adhesive strength is weakened if the surface is
dusty, oily or wet.
Installing the Control Center Horizontally
Apply the four supplied bottom pads to the bottom of the control center.
Peel off the seals of the bottom pads and apply to the four indented parts (screwed parts) on the bottom
of the control center.
CAUTIONS
• Be sure to use the bottom pads when installing the control center horizontally. Otherwise, the front door of the control
center cannot open.
• Be sure to apply the bottom pads to the indented parts (screwed parts) on the bottom panel. Do not apply them to the
indented parts on the top of the control center.
Bottom panel
Bottom pad
Peel off the seal.
Apply to the indented part.
8
Note
• Using only the supporting stand makes the control center unstable and the front door cannot open. Be sure to use the side pads as well.
CAUTIONS
• Be sure to place the control center with the left side down.
• When installing the control center vertically on a high place such as on a shelf, do not place close to the edge.
Installing the Control Center Vertically
Apply the two supplied side pads to the side of the control center and attach to the supplied supporting stand.
1 Peel off the seals of the side pads and apply to the two indented parts (near to the front panel) on the
left side of the control center.
2 Attach the control center with the pads applied side facing down to the supporting stand as shown in
the illustration below.
A supporting stand
Lift in this direction.
Front panel
Apply to the indented part.
Bottom panel
Rear panel
Apply to the indented part.
Side pad
Peel off the seal.
Front panel
INSTALLATION
9
English
PREPARATION
NATURAL SOUND HOME THEATER SYSTEM VS-10
DIGITAL
DIGITAL
DOLBY
SURROUND
CONNECTIONS
CAUTION
Always be sure to turn off the power of the control center and any component to be connected when making connections.
To ensure proper connections
• Connect the white plug of the connection cord to the left “L” (white) audio signal terminal and connect the red plug to the
right “R” (red) terminal.
• Insert the plug securely. If the plug is not inserted securely, noise may result or sound may not be output.
• Since the method of connection and terminal names differ depending on the component being used, be sure to refer to the
instruction manuals for all components being connected.
• After connections have been made, check one more time that wiring has been made properly.
Page 12
Pages 13 and 14
Page 14
Pages 10 and 11
Video game player,
DVD player,
Camcorder, etc.
TV (monitor)
VCR, etc.
DVD player, etc.
Control center
Main speakers
To AC outlet
YAMAHA subwoofer, center speaker
and rear speakers NX-SW10
(sold separately)
10
DIGITAL 1
(V/PCM)
VIDEO 1 TV
VIDEO SIGNAL
INPUT
MAIN SPEAKERS
SUBWOOFER
OUT
MONITOR
OUT
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
+
–
+
–
RL
OUTPUT INPUT
AUDIO/VIDEO
IN
AUDIO/VIDEO
OUT
R L
AUDIO
IN R
VIDEO IN
VIDEO OUT
AUDIO
IN L
R
L
AUDIO
OUT R
AUDIO
OUT L
Connect the audio output terminals on the TV (monitor) to the TV audio input terminals on the control center using the
supplied audio connection cord and the video input terminal on the TV (monitor) to the MONITOR OUT terminal on the
control center using the supplied video connector cord.
y
• The sound from the TV can be heard using the speakers connected to the control center. (Although you can also hear the sound from the TV
speakers, we recommend you to reduce the TV volume so that you may enjoy the full benefit of the VS-10.)
• To monitor the picture output from the component such as a DVD player, cable TV tuner, camcorder, video game player, etc. of which the
video output terminal is connected to the video input terminal on the control center (as described on pages 11 and 12), switch the video
input of the TV (monitor) connected to the MONITOR OUT terminal on the control center.
• The TV (monitor) without the audio output terminals cannot be connected to the control center.
TV (monitor)VCR, etc.
Audio connection cord (supplied)
Control center (rear panel)
Connecting a TV or VCR
■ Connecting a TV (monitor)
Video connection cord
(supplied)
CONNECTIONS
As this terminal is used for an
examination in the factory, do not
connect any equipment to this terminal.
11
English
PREPARATION
DIGITAL 1
(V/PCM)
VIDEO 1 TV
VIDEO SIGNAL
INPUT
MAIN SPEAKERS
SUBWOOFER
OUT
MONITOR
OUT
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
+
––
RL
OUTPUT
OPTICAL DIGITAL
OUTPUT
OUTPUT OUTPUT
R L
R L
VIDEO IN VIDEO IN
VIDEO OUT
AUDIO
OUT R
AUDIO
OUT L
VIDEO
OUT
AUDIO IN LAUDIO IN R
Connect the optical digital output terminal on the DVD player, etc. to the DIGITAL 1 (optical) digital input terminal on the
control center using a commercially available optical fiber cable. This connection brings you digital sound.
When connecting the cable TV tuner, etc. without a digital output terminal, connect the audio output terminals to the VIDEO
1 audio input terminals on the control center using a commercially available audio connection cord (2 pin).
Also, connect the video output terminal on the DVD player to the DIGITAL 1 video input terminal on the control center
using a commercially available video connection cord and the video output terminal on the cable TV tuner to the VIDEO 1
video input terminal on the control center using a commercially available video connection cord. However, when the DVD
player, cable TV tuner, etc. has an S video output terminal, connect to the S video input terminal on the TV (monitor) directly
so that you can obtain the high quality picture.
y
• The sound from a DVD player, cable TV tuner, etc. can be heard using the speakers connected to the control center. The sound cannot be
heard from the TV’s speakers. The sound from a DVD player, cable TV tuner, etc. cannot be heard when the power of the control center is
turned off.
• The VS-10 cannot record any audio or video source.
Cable TV tuner, etc.
DVD player, etc.
Control center (rear panel)
■ Connecting a DVD player, cable TV tuner, etc.
Video connection
cord (commercially
available)
Video
connection cord
(commercially
available)
Audio connection cord
(commercially available)
Optical fiber cable
(EIA standard)
(commercially available)
Remove the cap covering the
DIGITAL 1 terminal (optical)
when connecting an optical
fiber cable. Safely store the
cap and always re-insert it in
the terminal when the terminal
is not in use. (This cap
prevents the entrance of dust.)
Anti-dust cap
CONNECTIONS
Anti-dust cap
12
POWER
STANDBY
PHONES
SILEN
T
DIGITAL2 VIDEO2
RL
OUTPUT
OUTPUTOUTPUT
OPTICAL DIGITAL
OUTPUT
AUDIO
OUT R
AUDIO
OUT L
R L
AUDIO
IN L
L
VIDEO OUT
VIDEO IN
VIDEO OUT
VIDEO IN AUDIO
IN R
R
When connecting the video game player, DVD player, etc. with a optical digital output terminal, connect the optical digital
output terminal to the DIGITAL 2 (optical) digital input terminal on the control center using a commercially available optical
fiber cable. This allows you to enjoy a digital sound.
When connecting the camcorder, video game player, etc. without a digital output terminal, connect the audio output terminals
to the VIDEO 2 audio input terminals on the front panel of the control center using a commercially available audio
connection cord (2 pin).
Also, connect the video output terminal on the camcorder, video game player, etc. to the DIGITAL 2 (VIDEO 2) video input
terminal on the control center using a commercially available video connection cord. However, when the camcorder, video
game player, etc. has an S video output terminal, connect to the S video input terminal on the TV (monitor) directly so that
you can obtain the high quality picture.
y
• The sound from camcorder, video game player, etc. can be heard using the speakers connected to the control center. The sound cannot be
heard from the TV’s speakers. The sound from a camcorder, video game, etc. cannot be heard when the power of the control center is
turned off.
• The VS-10 cannot record any audio or video source.
Video game player or DVD
player, etc. which has an optical
digital output terminal
Camcorder or video game
player, etc. which has no
optical digital output terminal
Audio connection
cord (commercially
available)Optical fiber cable
(EIA standard)
(commercially
available)
Connect either.
Control center (Front panel)
■ Connecting a camcorder, video game player, etc.
Video connection
cord
(commercially
available)
Remove the cap covering the DIGITAL 2 terminal
(optical) when connecting an optical fiber cable.
Safely store the cap and always re-insert it in the
terminal when the terminal is not in use. (This cap
prevents the entrance of dust.)
Anti-dust cap
Video
connection cord
(commercially
available)
CONNECTIONS
Less than 14 mm
Use the optical fiber cable of which the plug
dimensions are less than 14 mm.
Anti-dust cap
Optical fiber cable
13
English
PREPARATION
DIGITAL 1
(V/PCM)
VIDEO 1 TV
VIDEO SIGNAL
INPUT
MAIN SPEAKERS
SUBWOOFER
OUT
MONITOR
OUT
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
+
–
+
–
AC OUTLET
0.8A MAX. 120V
60Hz 100W MAX.
UNSWITCED
+
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
–
+
–
1
2
3
MAIN SPEAKERS
CAUTIONS
• Do not let the bare speaker wire touch each other and do not let them touch any metal part of the speakers. This could
damage the speakers.
• Do not mistakenly connect positive (+) to negative (–) or vice versa when connecting speaker cords.
• Insert the speaker cords securely so that positive (+) and negative (–) do not short. The speaker may not output any
sound or may output noise, causing damage to the speakers, if speaker cords are not inserted securely.
• Only insert the bare wire portion of the speaker cords into the holes. Sound will not be output if you insert as far as the
plastic insulation part of the cord.
• Secure the speaker cords so that they will not catch on hands or feet.
Connecting the Main Speakers
Connect the main speakers to the control center.
Note
• Do not connect any speakers to the speaker terminals on the control center except for the supplied main speakers (NX-VS10M). Damage
may result if a different speaker is connected.
Right main speaker (Rear panel) Left main speaker (Rear panel)
Bare wire
Tab
Control center (Rear panel)
1 Open the tab.
2 Insert the bare wire of the speaker cord into
the hole.
3 Return the tab until it clicks.
• Connect the white cord to the + terminal (red), and the
black cord to the – terminal (black).
• Once connected, pull gently on the speaker cords to
check that they are connected securely.
CONNECTIONS
14
DIGITAL 1
(V/PCM)
VIDEO 1 TV
VIDEO SIGNAL
INPUT
MAIN SPEAKERS
SUBWOOFER
OUT
MONITOR
OUT
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
+
–
+
–
0.8A MAX. 120V
60Hz 100W MAX.
UNSWITCHED
AC OUTLET
Once all connections have been made, check them one more
time. Finally, insert the plug of the power supply cord for
the control center into an AC outlet. Disconnect the power
supply cord if you will not use the unit for an extended
period.
■ AC OUTLET (UNSWITCHED)
(Except for Australia model)
Use this outlet to connect the power cord of your
component to this unit. This outlet will supply power to any
connected component regardless of the operation of the
POWER switch on the control center (or p on the remote
control). The maximum power that can be connected to the
AC OUTLET is 100 W.
To AC outlet
Control center
Note
• When the power of the control center is turned off, that of the YAMAHA subwoofer SW-VS10 is also turned off accordingly.
y
• For details regarding connections, please refer to the instruction manuals for your subwoofer or the owner’s manual for the YAMAHA
subwoofer, center speaker and rear speakers NX-SW10 (sold separately).
Connecting the AC Power Supply Cord
Match the mark on the
plug with the mark on
the terminal and insert.
To SYSTEM
CONNECTOR terminal
System connector cable
supplied with the
YAMAHA NX-SW10
To SYSTEM
CONNECTOR
terminal
YAMAHA subwoofer, center speaker and
rear speakers NX-SW10 (sold separately)
Control center
Connecting the Control Center to the Subwoofer
Although the VS-10 alone can be used to reproduce rich and natural sounding audio, the additional use of a subwoofer allows
you to enjoy powerful bass tones.
Connecting the YAMAHA subwoofer, center speaker and rear speakers NX-SW10 (sold separately) can not only increase
bass sensitivity but improve the surround effect.
When connecting your subwoofer, connect
the input terminal on the subwoofer to the
SUBWOOFER OUT terminal on the control
center using a commercially available audio
connection cord (1 pin).
CONNECTIONS
AC OUTLET (UNSWITCHED)
15
English
PREPARATION
EFFECT
DSP
SET
AVMUTE
TEST
SUBWOOFER
+
SUBWOOFER
–
NIGHT MODE
231
564
8
MENU
97
0
+–
ENTER
LAST
–
VOL VOL
+
VS10 TV VCR CBL
ON/OFF
CH
CH
MEMORY
1
2
RIGHTCENTERLEFT
RIGHT
SURROUND
LEFT
SURROUND
RIGHTLEFT
RIGHT
SURROUND
LEFT
SURROUND
Rear speakers
Main
speaker
● When the NX-SW10 is connected:
(Virtual)(Virtual)
2 Press TEST.
A test tone (like pink noise) will be output in the
following order.
● When only the VS-10 is connected or the
VIRTUAL SURROUND is selected:
1 Press p to turn on the power.
If the STANDBY indicator is lit, turn on the power
using p on the remote control. If the main power is
off (when the STANDBY indicator is not lit), turn on
the power by pressing POWER on the control center.
CAUTION
When the NX-SW10 (sold separately) is connected to the
control center, insert the plug of the AC power supply
cord of the subwoofer SW-VS10 into an AC outlet
beforehand and turn on the power of the control center.
ADJUSTING THE SPEAKER OUTPUT LEVELS
When reproducing the source encoded with a Dolby Digital, Dolby Surround or DTS, it is important to adjust the sound
output level heard at the listening position to the same from each speaker. Therefore, the best performance of these digital
sound fields can be obtained. Even when the other sound field is selected, you can enjoy the characteristics of each sound
field.
Speaker output levels may be adjusted using the remote control before playback by following the steps.
Main
speaker
Main
speaker
Main
speaker
16
3 Adjust the level of the test tone using VOL +/–.
(Adjust to your listening level.)
Pressing VOL + increases the level, while pressing
VOL – decreases the level.
4 Adjust the sound output level of each speaker
while listening to the test tone.
Pressing f increases the level, while pressing w
decreases the level.
y
• When only the VS-10 is connected:
Adjust the sound output levels of the rear virtual speakers and the
main speakers so that they become almost the same.
• When the NX-SW10 is connected:
Adjust the sound output levels of the center speaker and the rear
speakers so that they become almost the same as that of the main
speakers.
Notes
• When the sound output levels of the main speakers are adjusted,
adjust the sound output levels of the center speaker, rear speakers
and rear virtual speakers again.
• The sound output levels of right and left virtual speakers cannot
be adjusted separately. While one level is adjusted, the other is
also adjusted similarly.
• When the headphones are connected, the order of each speaker
from which a test tone is heard is the same as that of VS-10 only.
However, the sound output level of main speakers cannot be
adjusted. Only the sound output level of rear speakers can be
adjusted, however, that level cannot be adjusted for each right or
left rear speaker separately. (Adjustable range: –3 to +3 dB)
5 When the adjustment is complete, press TEST.
A test tone stops.
y
The sound output level can be adjusted in the following range.
• When only the VS-10 is connected or the VIRTUAL
SURROUND is selected:
– Right and left main speakers: –10 to ±0 dB
– Rear virtual speakers: –3 to +3 dB
– The minimum level for the main speakers is –10 dB, while that
for the rear virtual speakers is –3 dB.
• When the NX-SW10 is connected:
– Right and left main speakers: –10 to ±0 dB
– Center speaker: –20 to +6 dB
– Right and left rear speakers: –20 to +6 dB
– The minimum level for the main speakers is –10 dB, while that
for the center speaker and the rear speakers is –20 dB.
EFFECT
DSP
SET
AVMUTE
TEST
SUBWOOFER
+
SUBWOOFER
–
NIGHT MODE
231
564
8
MENU
97
0
+–
ENTER
LAST
–
VOL VOL
+
VS10 TV VCR CBL
ON/OFF
CH
CH
MEMORY
5
4
3
ADJUSTING THE SPEAKER OUTPUT LEVELS
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
Pagina se încarcă ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
Yamaha VS-10 Manual de utilizare
- Categorie
- Receptoare AV
- Tip
- Manual de utilizare
în alte limbi
- Türkçe: Yamaha VS-10 Kullanım kılavuzu
- français: Yamaha VS-10 Manuel utilisateur
- čeština: Yamaha VS-10 Uživatelský manuál
- русский: Yamaha VS-10 Руководство пользователя
- English: Yamaha VS-10 User manual
- suomi: Yamaha VS-10 Ohjekirja
- polski: Yamaha VS-10 Instrukcja obsługi
- Deutsch: Yamaha VS-10 Benutzerhandbuch
- italiano: Yamaha VS-10 Manuale utente
- español: Yamaha VS-10 Manual de usuario
- svenska: Yamaha VS-10 Användarmanual
- dansk: Yamaha VS-10 Brugermanual
- português: Yamaha VS-10 Manual do usuário
- Nederlands: Yamaha VS-10 Handleiding
Lucrări conexe
-
Yamaha AV-S77 Manualul proprietarului
-
-
-
-
Yamaha NX-S100S Manual de utilizare
-
-
Yamaha DVR-S200 Manual de utilizare
-
-
Yamaha AVXS80 Manual de utilizare
-