Yamaha V1 Manualul proprietarului

Marca: Yamaha

Model: V1

Categorie: Routere

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

V1.2

Wireless DCP Owner’s Manual

Wireless DCP

Owner’s Manual

Introduction

Thank you for downloading the Wireless DCP app for Yamaha Matrix Processor MTX-series.

Wireless DCP allows these processors to be controlled remotely using smart devices. In specific

terms, it has been designed to allow users to control volumes and presets on MTX processors via

a simple, intuitive graphical interface from anywhere within wireless range.

The latest version of the firmware for MTX-series products can be downloaded from the follow-

ing web site.

http://www.yamahaproaudio.com/

The descriptions in this document use display examples on an iOS device. If you are using an

Android device, the instructions are the same; simply follow along with the display on your

device.

Notices

• The Wireless DCP application and this manual are copyright of Yamaha Corporation.

• Copying of the Wireless DCP application or reproduction of this manual in whole or in part by any means

is expressly forbidden without the written consent of Yamaha Corporation.

• Yamaha Corporation makes no representations or warranties with regard to the use of the Wireless DCP

application and this manual and cannot be held responsible for the results of usage thereof.

• Screen displays as illustrated in this manual are for instructional purposes and may appear somewhat

different from those on your smart device.

• Apple, the Apple Logo, iPhone, iPod touch, iPad, and iOS are trademarks of Apple Inc., registered in the

U.S. and other countries.

• Android is a trademark of Google Inc.

• Company and product names used in this manual are trademarks or registered trademarks of their

respective companies.

• Future upgrades of the Wireless DCP application and any changes in specifications and functions will be

announced separately.

Wireless DCP Owner’s Manual

1. System Requirements .......................................................................3

2. Getting Started................................................................................3

3. Configuration .................................................................................4

3.1 MTX Processor........................................................................................................4

3.2 iOS Device ...............................................................................................................7

3.3 Wireless DCP.........................................................................................................11

3.3.1 Offline Demo Mode ....................................................................................12

3.3.2 Making Connections...................................................................................14

3.3.3 Entering a PIN ............................................................................................15

3.3.4 Resetting PINs ...........................................................................................17

3.3.5 Manual IP...................................................................................................18

4. Controller Screen........................................................................... 23

5. Preset Screen ............................................................................... 25

6. Player Screen ............................................................................... 26

7. Settings Screen............................................................................. 30

7.1 Overview................................................................................................................30

7.2 Selecting a Device..................................................................................................32

7.3 Changing PINs.......................................................................................................33

7.4 Staff Settings.........................................................................................................34

7.5 Device Date and Time ............................................................................................35

7.6 Style (Controller Formats) .....................................................................................36

7.7 Displaying App Information ...................................................................................37

8. Troubleshooting ............................................................................ 38

Contents

Wireless DCP Owner’s Manual

1. System Requirements

• Smart devices supported:

iPhone (iPhone3GS or later), iPod touch (3rd generation or later), iPad

Android OS 4.2 or later

Please refer to the Yamaha Pro Audio website shown below for the latest tested Android devices

and OS versions.

http://www.yamahaproaudio.com

• Yamaha Matrix Processor MTX-series

• Wi-Fi access point (preferably with 802.11n, 5-GHz capability)

• Cat 5e cable (for connecting MTX processor and Wi-Fi access point)

2. Getting Started

Set up your Wi-Fi access point as described in the manual that came with it. While no special settings

are needed, we recommend using WPA security or the like in order to prevent unwanted devices from

joining the network. Less experienced Wi-Fi users may benefit from the following suggestions.

1. Assign a name to your wireless network.

2. Activate a security mode (such as WPA2) and set a password.

3. Select a wireless mode such as 802.11n or 802.11g.

4. If available, enable Auto Channel Selection so that the wireless channel with the lowest level

of interference will be automatically selected.

We recommend using 802.11n networks as they support faster communication between smart devices

and Wi-Fi access points. We also recommend using Wi-Fi access points with multiple external anten-

nae as this makes it easier to connect to the network. For increased security, meanwhile, we recom-

mend using a stealth mode or MAC address filtering.

Wireless DCP Owner’s Manual

3. Configuration

Using a Cat 5e cable, connect your Wi-Fi access point to the Network port on the MTX processor.

Insert an Ethernet switch as necessary.

3.1 MTX Processor

Smart device

Wi-Fi access point

Computer

MTX processor

Ethernet

switch

Wireless DCP Owner’s Manual

3. Configuration

Refer to the MTX setup manual for instructions on setting the MTX processor.

Configure Wireless DCP according to the MTX Editor User’s Manual.

 Setting the controllers (Wireless DCP dialog box)

 Setting the presets (Preset dialog box)

When the above settings are sent from the MTX Editor to the MTX processor (q), the Wireless

DCP operates to retrieve the contents (w).

Smart device

Wi-Fi access point

Computer

MTX processor

Wireless DCP Owner’s Manual

3. Configuration

 Setting Up

Below are instructions for the basic configuration.

1. Check IP address mode of the MTX processor to which the Wireless DCP will be con-

nected.

Check that DIP SW6 on the rear panel of the MTX processor is set to UNIT ID (upper position).

The IP address of the MTX processor is now set as the UNIT ID (i.e., 192.168.0.[UNIT ID]).

2. Set the PC’s IP address to DHCP (obtain an IP address automatically) for use with

MTX Editor. The PC will obtain its IP address from the DHCP server on the access

point.

3. Change the IP address of the Wi-Fi access point.

The IP address of the MTX processor and the Wi-Fi access point should be the same subnet. Use

192.168.0.254 for the access point Wi-Fi IP address, ensuring this does not conflict with any other

devices on the network, such as a gateway address. Refer to the user manual of your particular

access point to set the IP address of the Wi-Fi access point.

4. Configure the DHCP server function in the Wi-Fi access point.

The IP address of the Wi-Fi access point and the DHCP address range must not have the same IP

address as any other device (i.e., MTX/XMV) in the network. We recommend a setting the DHCP

address within the range of 192.168.0.150 to 192.168.0.200. Refer to the user manual of your partic-

ular access point. It is important to ensure that no IP addresses are duplicated by multiple devices.

5. Launch MTX Editor and configure the Device Configuration Wizard according to the

devices present.

6. Configure the Wireless DCP settings in MTX Editor and store them as a library.

7. Assign the Wireless DCP library to all presets requiring control.

8. Go online and synchronize to the devices.

This will send all configured settings to the MTX processors.

9. Recall the preset made in step 7 from MTX Editor or the front panel of the MTX pro-

cessor.

10. Configure the Wi-Fi settings of the smart device.

Refer to the Wi-Fi configuration in “iOS Device” in section 3.2 about the iOS device.

11. Launch Wireless DCP on your smart device.

12. Confirm that the MTX processor is present in the “Select Device” screen.

If no MTX processor is present, turn off Wi-Fi in the smart device settings, then turn it back on again.

If the “Not connected” screen is displayed, check again that all presets to be controlled have the wire-

less DCP library assigned to them in MTX Editor; otherwise no MTX processor will be recognized by

the Wireless DCP. If the MTX processor is not automatically present in the “Select Device” screen

after the above settings are made, manually add the MTX processor’s IP address (3.3.5 Manual IP).

13. At the “Select Device” screen, select the MTX processor that you configured.

14. Unless a PIN (a four-digit number) has already been set, tap “Join” on the onscreen

keyboard.

15. The “Controller 1” screen will appear.

The Change PINs (page 33), and Staff Settings (page 34) can be configured according to the project.

NOTE

When changing previously configured Wireless DCP library settings, such as assigning parameters to switches and

knobs, the latest settings will not be reflected automatically on the smart device after going online to other devices.

The first time after going online, always recall the preset from the front panel or within MTX Editor.

Wireless DCP Owner’s Manual

3. Configuration

1. Go to Settings. Tap Wi-Fi. 2. Turn on Wi-Fi.

3.2 iOS Device

Wireless DCP Owner’s Manual

3. Configuration

3. Under Choose a Network…, select the Wi-

Fi access point to which the MTX processor

is connected.

4. Enter the Wi-Fi access point’s password.

Refer to Section

2. Getting Started for more

details.

Wireless DCP Owner’s Manual

3. Configuration

5. Configure your network as follows. (Use Procedure 5-1 if the network assigns IP addresses auto-

matically; use Procedure

5-2 if not.)

5-1. Select DHCP if the network’s DHCP

server automatically determines IP

addresses.

5-2. Select Static if you need to manually

set an IP address.

1. Verify that settings have been made for IP

Address, Subnet Mask, Router, and DNS.

2. Press the Home button to complete the network

setting process.

1. IP Address: For the first three numbers, use those

from the MTX processor’s IP address. Set a dif-

ferent value for the fourth number.

2. Subnet Mask: Enter “255.255.255.0”.

3. Router: Enter the IP address of the router or Wi-Fi

access point to be used.

4. Enter the IP address of the DNS or Wi-Fi access

point to be used.

5. Press the Home button to complete the network

setting process.

Wireless DCP Owner’s Manual

3. Configuration

 Key points for network configuration

1. The devices to be connected must have IP addresses from the same network (or subnet).

*: If using a Wi-Fi access point that is not also a router, set the IP address for accessing it.

2. Eight smart devices running Wireless DCP can be connected to each MTX processor. (However, only one

device can be logged into with an administrator PIN.)

3. Connect the MTX processor to the LAN connector of the Wi-Fi access point.

If you connect to a WAN (Internet) connector, the smart device will not be able to communicate properly with

the MTX processor.

Good combination of settings

Incorrect combination of

settings

Router with integrated Wi-Fi*

and DNS

192.168.0.254 192.168.11.1

MTX processor 192.168.0.1 192.168.0.1

Smart device 192.168.0.200 192.168.11.50

Computer 192.168.0.253 192.168.0.253

Smart device

Wi-Fi access point

Computer

MTX processor

Wireless DCP Owner’s Manual

3. Configuration

Tap the Wireless DCP app to launch it. The Select Device screen will be displayed.

3.3 Wireless DCP

Device list

MTX processors available for

connection are displayed

here. When you select one,

the Enter PIN screen will be

displayed.

DEMO button

Tap DEMO on this screen to activate

Offline Demo mode. In this mode, you

can try out Wireless DCP functions and

the user interface without performing any

actual operations on the MTX processor.

Manual IP list button

The Manual IP screen will be

displayed. Refer to Section

3.3.5 Manual IP for details.

If you launch Wireless DCP with Auto-connect mode active, the app will automatically reconnect to

the MTX processor it was most recently used with. You can use the Auto-connect switch to modify

this setting. Refer to Section

3.3.3 Entering a PIN for details.

Wireless DCP Owner’s Manual

3. Configuration

 3.3.1 Offline Demo Mode

In Offline Demo mode, Wireless DCP disconnects from the MTX processor so you can try out the

app’s functions and user interface without performing any actual operations. To activate this

mode, tap DEMO on the Select Device screen.

Controller pane

Use this pane to try out the faders and buttons.

Page button

Tap to display the Select Page screen.

Controller 1 and

Controller 2 buttons

Tap to switch the Controller

pane’s display.

Settings button

Tap to display the

Settings screen.

Player button

Tap to display the

Player screen.

Preset button

Tap to display the

Preset screen.

Wireless DCP Owner’s Manual

3. Configuration

 From Demo mode to Normal mode

On the Settings screen, tap Select Device... to display the Select Device screen. Here, you can

select the MTX processor to be controlled. When you do so, the Enter PIN screen will be dis-

played.

Wireless DCP Owner’s Manual

3. Configuration

 3.3.2 Making Connections

On the Select Device screen, tap the MTX processor to be controlled.

When you select a processor, the Enter PIN screen will be displayed.

Information displayed

Upper line: Device name (configured using MTX Editor)

Lower line: Unit ID and model name

Wireless DCP Owner’s Manual

3. Configuration

 3.3.3 Entering a PIN

Enter a valid PIN to connect to the selected MTX processor.

Reset button

Tap to display the Reset PIN screen.

Cancel button

Tap to return to the Select Device

screen without entering a PIN.

Auto-connect switch

Turn this switch on to connect auto-

matically whenever the app is

launched.

 To enter a PIN

1. Enter your PIN using the keyboard.

2. Tap Join to connect to the MTX processor. Upon connection, the Controller 1 pane will be displayed.

NOTE

PINs take the form of a four-digit number, and none are set when the app is first launched. In this condition, it

is possible to log into Wireless DCP without entering a PIN by simply tapping Join. It is important, therefore, to

set PINs. Refer to Section

7.3 Changing PINs for details.

Wireless DCP Owner’s Manual

3. Configuration

There are two different types of PIN—one for administrator, one for staff. As shown below, cer-

tain functions are available only when logged into the MTX processor using an administrator PIN.

Administrator Staff

Preset



(but restricted by administrator)

Player



(but restricted by administrator)

Device Date and Time



(but restricted by administrator)

Change PIN

 ×

Staff Settings

 ×

Style



(offline demo mode only)

NOTE

If you assigned the same PIN for both administrator and staff, you will not be able to log in as staff.

Wireless DCP Owner’s Manual

3. Configuration

 3.3.4 Resetting PINs

Reset the PINs for Wireless DCP.

 To reset PINs

1. Tap Reset to display the Reset PIN

screen. If, for example, you forget a PIN,

you can use this screen to reset (or

remove) it. Note that both administrator

and staff PINs are reset by this action.

2. Enter the MAC address of the MTX pro-

cessor to connect using the keyboard.

You can check the MAC address from the

MTX Editor.

3. You will be asked to confirm that you wish

to reset the PINs. Tap Yes to do so.

Wireless DCP Owner’s Manual

3. Configuration

 3.3.5 Manual IP

Add the IP address to connect the MTX processor and manually display the device for connection

on the device list.

 Entering the IP address

 Step A : List button

1. Tap the Manual IP list button to display the

Manual IP screen.

2. Tap the + button to display the Add IP

Address screen.

3. Enter the IP address using the keyboard.

4. Tap the Done button to check the added

IP address on the Manual IP screen.

Normally, MTX processors are automatically

detected and displayed on the Select Device list.

However, in rare cases auto-detection may not be pos-

sible with certain Wi-Fi device specifications.

In such cases, use the Manual IP function to instead

manually add the MTX processor’s IP address.

Once the IP address is added into the Manual IP list,

that MTX processor becomes available on the Select

Device list.

Wireless DCP Owner’s Manual

3. Configuration

 Entering the IP address

 Step B : Device name

1. Tap and Hold (Long press) the device

name to display the pop-up screen for

confirming the IP address.

2. Tap the Yes button to add the device’s IP

address into the Manual IP list. An “Added”

popup message displays.

3. Tap the OK button.

Wireless DCP Owner’s Manual

3. Configuration

You can edit the added IP address or delete it.

 Editing the IP address

1. Tap the IP address for editing to display

the Edit IP Address screen.

2. Edit the IP address as desired and tap the

Done button.

Pagina se încarcă ...

Yamaha V1 Manualul proprietarului

Marca: Yamaha

Model: V1

Categorie: Routere

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

V1.2

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha V1 El kitabı
français: Yamaha V1 Le manuel du propriétaire
čeština: Yamaha V1 Návod k obsluze
русский: Yamaha V1 Инструкция по применению
English: Yamaha V1 Owner's manual
suomi: Yamaha V1 Omistajan opas
polski: Yamaha V1 Instrukcja obsługi
Deutsch: Yamaha V1 Bedienungsanleitung
italiano: Yamaha V1 Manuale del proprietario
español: Yamaha V1 El manual del propietario
svenska: Yamaha V1 Bruksanvisning
dansk: Yamaha V1 Brugervejledning
português: Yamaha V1 Manual do proprietário
Nederlands: Yamaha V1 de handleiding

Yamaha V1 Manualul proprietarului

Acest manual este potrivit și pentru

Yamaha V1 Manualul proprietarului

în alte limbi

Lucrări conexe