6
● Do not charge other battery types with the supplied
charger. Confirm there is no flammable material within
2 m of the charger during charging.
● For long-term storage of the battery, make sure it is
fully charged every half year to ensure the battery
quality. Otherwise, damage may occur.
● DO NOT place the battery near heating or fire source.
Avoid direct sunlight.
● DO NOT swallow the battery to avoid chemical burns.
● DO NOT place the battery in the reach of children.
● CAUTION: Risk of explosion if the battery is replaced by
an incorrect type.
● Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result
in an explosion.
● Do not subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas.
● When the device is powered off and the RTC battery is
full, the time settings can be kept for 90 days.
● In the first use, power on the device and charge the RTC
battery with the lithium battery for more than 10
hours.
● The battery voltage is 3.7 V, and the battery capacity is
5400 mAh.
Maintenance
● If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
● Wipe the device gently with a clean cloth and a small
quantity of ethanol, if necessary.
● If the device is used in a manner not specified by the
manufacturer, the protection provided by the device
may be impaired.
● Please notice that the current limit of USB 3.0
PowerShare port may vary with the PC brand, which is
likely to result in incompatibility issue. Therefore, it’s
advised to use regular USB 3.0 or USB 2.0 port if the
USB device fails to be recognized by PC via USB 3.0
PowerShare port.
● Your camera will periodically perform a self-calibration
to optimize image quality and measurement accuracy.
In this process the image will pause briefly and you will
hear a “click” as a shutter moves in front of the
detector. The self-calibration will be more frequent
during the startup or in very cold or hot environments.
This is a normal part of operation to ensure optimum
performance for your camera.
Using Environment
● DO NOT expose the device to extremely hot, cold,
dusty, corrosive, saline-alkali, or damp environments.
Make sure the running environment meets the
requirement of the device. The operating temperature
shall be -20 °C to 60 °C (-4 °F to 140 °F), and the
operating humidity shall be less than 95%.
● Place the device in a dry and well-ventilated
environment.
● DO NOT expose the device to high electromagnetic
radiation or dusty environments.
● DO NOT aim the lens at the sun or any other bright
light.
● When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may
burn out.
● The device is suitable for indoor conditions.
● The pollution degree is 2.
● The protection level is IP67.
Calibration Service
● We recommend you send the device back for
calibration once a year, and please contact the local
dealer for the information on maintenance points. For
more detailed calibration services, please visit
https://www.hikmicrotech.com/en/support/calibration
-service.html.
Technical Support
● https://www.hikmicrotech.com/en/contact-us.html will
help you as a HIKMICRO customer to get the most out
of your HIKMICRO products. The portal gives you access
to our support team, software and documentation,
service contacts, etc.
Emergency
● If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing
Subdistrict, Binjiang District, Hangzhou, Zhejiang 310052,
China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products might
be subject to export controls in various countries or
regions, including without limitation, the United States,
European Union, United Kingdom and/or other member
countries of the Wassenaar Arrangement. Please consult
your professional legal or compliance expert or local
government authorities for any necessary export license
requirements if you intend to transfer, export, re-export
the thermal series products between different countries.
1. Kurze Beschreibung
Die Wärmebildkamera zur Brandbekämpfung ist eine
robuste, kompakte, hochwertige Wärmebildkamera, die
für Inspekteure entwickelt wurde, um bei völliger
Dunkelheit und Rauch zu beobachten und so dazu
beizutragen, Leben zu retten, Eigentum zu schützen und
die Sicherheit der Inspekteure zu gewährleisten.
Verschiedene Bildmodi können die meisten Szenarien
abdecken.
Sie können auf Ihrem Telefon über HIKMICRO Viewer die
Live-Ansicht anzeigen und Fotos aufnehmen. Sie können
Bilder offline analysieren und einen Bericht über die App
generieren und teilen. Scannen Sie die QR-Codes auf der
Abdeckung, um die App herunterzuladen.
Sie können den HIKMICRO Analyzer
(https://www.hikmicrotech.com/de/industrial-
products/hikmicro-analyzer-software.html)
herunterladen, um Bilder professionell offline zu
analysieren und auf Ihrem PC einen Bericht in einem
individuellen Format zu erstellen.