Yamaha RHP80 Manualul proprietarului

Marca: Yamaha

Model: RHP80

Tip: Manualul proprietarului

LEVEL

PAD

RIM

LEVEL

PAD

RIM

If the following trouble occurs when the Real Head Pad is used, please check the following

points before asking your dealer for assistance.

INTRODUCTION

Thank you for purchasing the YAMAHA Real Head Pad RHP80/100/120/120SD. The

YAMAHA Real Head Pad series was developed as a trigger pad for use with an elec-

tric drum system. The pads utilize Remo Coated Ambassador heads. This system

delivers a richer, closer to acoustic feeling that extends greater expressive potential to

the drummer. Just like a real, high quality acoustic drum, the shell is made of birch

then covered with a clear finish.

To get the most out of your YAMAHA Real Head Pad Series, please read this manual

carefully. After reading, please keep it in a safe place for future reference.

OWNER’S MANUAL

Before setup, please make sure that all of the items listed below are present and accounted

for. If anything is missing, please contact the dealer from whom you purchased the unit.

Gray Flat Cushion

(Bottom)

Yellow Cushion

(Top)

■ About Replacing Worn Parts

(Rubber Hoop Cover, Cushions, etc.)

• This product uses parts (drum head, cushion, rubber hoop cover, Output Level Adjustment

knob, output jacks, etc.) that will wear or deteriorate over time. How these parts wear or

deteriorate will depend upon the environment, length of time, etc., in which the device is

used.

• Please ask the dealer from whom you purchased the device about replacing worn parts.

• Do not disassemble (except for when replacing the head or a cushion as described in this manual) or alter the

product. Doing so may result in damage or deterioration to the product.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a

heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation,

discoloration, damage or deterioration.

• To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the

product is soiled, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out

thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may result in

discoloration or deformation. Also pay close attention so as not to let the water and detergent come into

contact with the cushions used in the product, it may result in deterioration.

• When connecting or disconnecting cables, make sure to hold the cable by the plug. Also, make sure heavy or sharp

objects are not placed upon the cable. If excessive force is placed on the wire, it may result in the wire breaking.

• Pad Units (RHP80/100/120/

120SD) x1

• Stereo Phone Cable

(3m) x1

■ Handling Precautions

■ Inside This Package

Pad Unit

NOTE : When you use the corrugated cushion, put the

yellow cushion that was installed at the factory

on the bottom, then the corrugated cushion on

top with the corrugated side of the cushion in

contact with the drum head (in this case the

flat, gray cushion is not needed).

NOTE : When the corrugated cushion is not used, make

sure the other cushions are positioned in the

same manner as when the unit was shipped

from the factory, with the flat, gray cushion on

the bottom and the yellow cushion in contact

with the drum head. If the cushions are

reversed, it may result in deterioration of the

cushions.

■ What is Explained in this Manual

• The RHP80/100/120 are tom type (8”/10”/12”) trigger pads with rod clamps that can be

attached to a tom stand or rack.

• The RHP120SD is a 12” snare drum type trigger pad. It can be set on a snare stand

(YAMAHA:SS642, etc.).

RHP80 (8”)

RHP120SD (12”)

RHP120 (12”)

RHP100 (10”)

Rod Clamp Rod Clamp Rod Clamp

LEVEL

PAD

RIM

Drum Head

Rod Clamp

(The RHP120SD is not equipped with this clamp)

Clamp Bolt

(The RHP120SD is not

equipped with this bolt)

Hoop

Tuning Bolt

Lug

Shell

OUTPUT Jack

Bottom Cover

• Corrugated

Cushion x1

■ Replacing the Cushion

Like acoustic drums, the Real Head Pad’s drum head will wear over time. When it is time to

change the old head with a new one, please do so on your own. We recommend the use of

Remo Coated Ambassador 8", 10" and 12" drum heads, but you may use any other head that

you prefer. Just keep in mind that depending upon the drum head you use, the feel, sound,

output, etc. may be slightly different.

For sensing and sound deadening purposes,

the Real Head Pads utilize a cushion that pro-

vides support to the entire drum head from

within the pad. You can use the supplied cor-

rugated cushion in place of the cushion that

was installed at the factory. Use of the corru-

gated cushion offers a firmer feeling head.

Select the best cushion according to the type

of drum head you use.

■ Replacing the Drum Head

■ Troubleshooting

●

Multiple sounds are produced when the pad is struck once (Double Trigger).

Yellow Cushion

(Bottom)

Corrugated Cushion

(Top)

■ Part Names

The plug with the

two black rings

When the corrugated cushion is not used.

(As shipped from the factory)

When the corrugated cushion is used.

Rod Clamp

(The RHP120SD is not

equipped with this clamp)

● No Sound, Volume is Low

Problem

Is the Real Head Pad’s OUTPUT

jack properly connected to the In-

put jack on the DTXTREME/DTX/

DTXPRESS with the supplied ste-

reo phone cable (the plug with two

black rings)?

Is the Real Head Pads Output

LEVEL Adjustment set too low?

Is the drum head on the real head

pad too loose?

Is the DTXTREME/DTX/DTXPRESS

properly connected to a pair of

headphones or the external audio

device?

Is the DTXTREME/DTX/

DTXPRESS properly setup?

What to check.

If the pad is connected with a monaural phone cable

(the plug with one black ring), the rim shot s o u n d

will not be produced. Also, if the Real Head Pad is con-

nected to an INPUT number on the DTX/DTXPRESS

that is not capable of producing rim shots, the sound

will not be produced. (Refer to the “Connections” sec-

tion above.)

If the level is set too low, the signal level sent when the pad

is hit will be very low so, the DTXTREME/DTX/DTXPRESS

will not be able to produce sufficient volume from this low

level signal.

If the drum head is too loose, the output from the rim sensor

may be reduced. Use a tuning key to adjust the tension on the

head. (Refer to the previous “Setting Up” section.)

Check connections, power switches or volume settings

on the external devices.

Check if the volume setting assigned to each of the

DTXTREME/DTX/DTXPRESS’s INPUT numbers is not

set too low (refer to the “To Increase the Sound Vol-

ume” section above).

Also, check to see if the headphone volume etc. is not

set too low.

Problem

Is the Real Head Pad’s Output

LEVEL adjustment knob set too

high?

What to check.

If the Output LEVEL knob is set too high, the large sig-

nal remains for a longer time causing the DTXTREME/

DTX/DTXPRESS to produce multiple triggers. Use the

previously explained Output LEVEL adjustment to set

the level to a proper level.

❇ If the double triggers continue even after you have tried the solutions listed above, use the DTXTREME/DTX/

DTXPRESS “Self Rejection” function to control the problem. Refer to the Owner’s Manual supplied with the

DTXTREME/DTX/DTXPRESS for more information.

■ Setting Up

Insert the Tom Holder (6-sided), on a rack stand

or tom stand, into the Rod Clamp attached to

the Pad, and tighten the Clamp Bolt firmly.

(RHP80/100/120)

* Only the following inputs can be used.

DTXTREME: INPUT 1-8, 9/10-15/16

DTX: INPUT 9/10, 11/12

DTXPRESS: INPUT 9/10

Since other INPUTS are designed for use with pad trigger/rim switch

type pads (TP-80S, etc.), only the pad will be able to produce sound

when a Real Head Pad is connected.

Controls the trigger output level produced by the Real Head Pads. Output produced by either the

pad section (the drum head section) or rim section (rim shot) can be controlled individually. Turn

the LEVEL adjustment knob to the right (+) to increase the level. Turn to the left (-) to decrease

the level. Adjust the level according to the amount of strength you use when playing the pad and

rim, the required dynamic range, or specific needs regarding the devices that you use.

NOTE : When the Real Head Pad is used with the DTXTREME/DTX/

DTXPRESS, the value on the Input Level display, found in the

Trigger Edit Mode’s [PAD GAIN] page, should be set to a value

somewhere between 90% and 95% when the pad is struck at ff (the

rim should be set the same for rim shots). For more information,

please refer to the “Owner’s Manual” supplied with your DTXTREME/

DTX/DTXPRESS.

If the Output LEVEL is set too high, the dynamic range may be

reduced, or problems such as double triggers (when a single stroke

produces multiply triggered sounds), and cross talk (hitting the pad

causes the sound assigned to the rim to be produced or vice versa)

may occur.

: Do not put excessive pressure on the level adjustment knob, it may

result in damage.

■ Specifications

Pad Diameter 8 inches

Size (including protrusions)

237(W) x 291(D) x 140(H)mm

Weight 1,740g

Includes Rod Clamp

● RHP80

Pad Diameter 10 inches

Size (including protrusions)

299(W) x 342(D) x 140(H)mm

Weight 2,080g

Includes Rod Clamp

● RHP100

Pad Diameter 12 inches

Size (including protrusions)

350(W) x 392(D) x 140(H)mm

Weight 2,390g

Includes Rod Clamp

● RHP120

Pad Diameter 12 inches

Size (including protrusions)

350(W) x 350(D) x 94(H)mm

Weight 1,990g

● RHP120SD

Sensor System Dual Trigger Type (Pad/Rim)

Control Output LEVEL Volume x2 (Pad/Rim)

Output Jack Standard Stereo Phone Jack (stereo)

Accessories Stereo Phone Cable (3m) x1, Corrugated Cushion x1, Owner’s Manual (this booklet) x1

* Improvements may result in a change in the specifications and/or design of the product without notice.

● For All types

Tom Holder

Rod Clamp

Insert

Clamp Bolt

NOTE : When attaching the Real Head Pads to a rack

system, we recommend that either the YAMAHA

Rack System RS100 or RS95 be used. Using a

ball clamp type tom holder like the RS100

allows the attachment of large pads like the

RHP120. A cylinder type tom holder like the

RS95 allows the attachment of lighter pads up

to the RHP80. When a large pad such as the

RHP100/120 is attached to the RS95, we

recommend that the tom holder TPCL100

(optional) be used. The RS60 and RS80 may

not provide adequate support for the Real Head

Pads. If you already own the RS80 rack

(RHP120SD)

The snare drum pad can setup on a snare

drum stand (YAMAHA: SS642, etc.) in the

same manner as a normal snare drum.

LEVEL

Adjustment

Knob

LEV

PAD

RIM

LEVEL

PAD

RIM

Sensor Location

Sensor LocationSensor Location

Sensor Location

■ Output Level (LEVEL) Adjustment

Use the supplied stereo phone cable to connect the pad’s output jack to the input (SNARE,

TOM1, etc.) of the DTXTREME/DTX/DTXPRESS. Connect the cable’s L-shaped plug to the pad.

NOTE : The RHP80/100/120/120SD Real Head Pads are dual trigger type electronic drum pads. Both the pad (the

drum head section) and the rim (the hoop section around the head that is used for rim shots) are individually

equipped with trigger sensors. A separate sound can be assigned to the rim to allow for rim shots *.

■ Connections

● About Rim Shot Sensitivity

The locations of the RHP80/100/120/120SD’s trigger sensors are shown in the illustration.

The highest sensitivity can be found in the direct vicinity of the sensor and will decrease as

you move away from the sensor. If you are going to use rim shots, we recommend that the

area of highest sensitivity be placed in an optimum position when setting up the pad.

To Increase the Sound Volume

To change the volume of the sound assigned to individual pads when the Real Head Pads are used

with the DTXTREME/DTX/DTXPRESS, first adjust the Output LEVEL as described previously,

then use the (VOICE) EDIT Mode to set the volume on the DTXTREME/DTX/DTXPRESS. Please

refer to the “Owner’s Manual” supplied with your DTXTREME/DTX/DTXPRESS.

SPECIAL MESSAGE SECTION

NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is

approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that

the charger is intended for the battery being charged.

When installing batteries, do not mix batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation

may result in overheating and battery case rupture.

Warning: Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the

laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.

Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.

NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.

Model Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

system, adding the VK80 Rack Reinforcement

Kit (optional) will increase the strength of the

rack to that of the RS95.

NOTE : Drum head tension can be adjusted by

tightening or loosening the tuning bolts on the

hoop with a tuning key.However, there will be

no change in the tone produced by the

DTXTREME/DTX/DTXPRESS, etc.

: Make sure the pads are properly setup on the

rack or stand. If the clamp bolts, etc. are not

tightened sufficiently, the pad may fall off

resulting in injury. Also, if the rack or stand is

not setup on a flat surface, the rack or stand

may overturn resulting in injury.

NOTE : Please make sure that head tension is even all

the way around the head. Uneven tension may

produce wrinkles, which may shorten the life of

the drum head.

NOTE : Make sure the drum head is tightened within a

proper range. Over tightening may result in

damage to the drum head, shell, etc. An overly

loosened head may result in a shorter life of

the drum head, cushion, or noise. Also, when

the head is too loose a metallic noise may

occur when playing rim shots, likewise, the

output from the rim sensor may be reduced and

the sound produced by the DTXTREME/DTX/

DTXPRESS may be reduced or not sound at

all when playing rim shots. The head may also

become loose over time, so occasionally

retighten the head.

● When the pad is hit, the sound assigned to the rim is also produced, or

vice versa (cross talk).

❇

If the cross talk continues even after you have tried the solutions listed above, use the DTXTREME/DTX/DTXPRESS

“Specified Rejection” function to control the problem (can be used on the following channels DTXTREME: INPUTS 9/

10-15/16, DTX: INPUTS 9/10, 11/12, DTXPRESS: INPUT 9/10). Refer to the Owner’s Manual supplied with the

DTXTREME/DTX/DTXPRESS for more information.

Problem

Is the Real Head Pad’s Output

LEVEL Adjustment knob set too

high?

What to check.

If the rim’s Output LEVEL knob is set too high, sympa-

thetic vibrations produced when the pad is hit may be trans-

mitted through the shell, etc. and picked up by the sensor

located in the rim which in turn causes the sound assigned

to the rim to be produced. Use the previously explained

Output LEVEL Adjustment to set the level to a proper level.

● When mounted on the rack and a pad is hit, a sound that is assigned to

another pad is also produced (cross talk).

❇ If the cross talk continues between other pads, even after you have tried the solutions listed above, use the

DTXTREME/DTX/DTXPRESS “Specified Rejection” function to control the problem. Refer to the Owner’s Manual

supplied with the DTXTREME/DTX/DTXPRESS for more information.

Problem

Is the rack system’s strength ad-

equate, or are sections of the rack

loose?

Is the Output LEVEL Adjustment

knob on each of the pads con-

nected to the rack system set too

high?

What to check.

If the clamp bolts, etc. are not tightened firmly when the

rack is assembled, the unstable section of the rack will

move about when the pad is hit. Vibrations are then trans-

mitted to sensors in the other pads resulting in other

sounds being produced. Please make sure that the rack

or stand is assembled firmly.

If the Output LEVEL knob on any of the pads is set too

high, sympathetic vibrations produced when another pad

is hit may be transmitted through the rack pipe, etc. and

picked up by the pad’s trigger sensor which in turn causes

the sound assigned to the pad to be produced. Use the

previously explained Output LEVEL Adjustment and set

the level to a proper level.

● When a rim shot is played, a metallic noise is produced.

For more information on the problems listed above and other problems, please refer to the “Owner’s Manual” supplied with

the DTXTREME/DTX/DTXPRESSS. If you can not solve the problem on your own, please contact the dealer from whom you

purchased the device.

Problem

Is the drum head on the Real Head

Pad too loose?

What to check.

When the drum head is too loose, a metallic noise may

be produced when a rim shot is played.

Use the tuning key to adjust head tension. (Refer to the

previous “Setting Up” section.)

3m Cable with Standard

Phone Plug (Stereo)

Connect

OUTPUT Jack

Location

OUTPUT Jack

Location

OUTPUT Jack

Location

OUTPUT Jack

Location

Yamaha RHP80 Manualul proprietarului

Marca: Yamaha

Model: RHP80

Tip: Manualul proprietarului

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha RHP80 El kitabı
français: Yamaha RHP80 Le manuel du propriétaire
čeština: Yamaha RHP80 Návod k obsluze
русский: Yamaha RHP80 Инструкция по применению
English: Yamaha RHP80 Owner's manual
polski: Yamaha RHP80 Instrukcja obsługi
Deutsch: Yamaha RHP80 Bedienungsanleitung
日本語: Yamaha RHP80 取扱説明書
italiano: Yamaha RHP80 Manuale del proprietario
español: Yamaha RHP80 El manual del propietario
svenska: Yamaha RHP80 Bruksanvisning
dansk: Yamaha RHP80 Brugervejledning
português: Yamaha RHP80 Manual do proprietário
Nederlands: Yamaha RHP80 de handleiding

Lucrări conexe

Alte documente

Nerf E8575 Spiderbolt Powered Blaster Toy Manualul utilizatorului