Philips S5510/45 Manual de utilizare

Series S5000

19

18

22

26

20

25

27

21

23 24

4

3

5

9

8

10

11

13

12

14

17

1

2

7

6

16

15

1

Series S5000

ENGLISH 4

БЪЛГАРСКИ 36

ČEŠTINA 72

EESTI 104

HRVATSKI 137

MAGYAR 170

ҚАЗАҚША 204

LIETUVIŠKAI 239

LATVIEŠU 272

МАКЕДОНСКИ 305

POLSKI 342

ROMÂNĂ 376

РУССКИЙ 410

SLOVENSKY 447

SLOVENŠČINA 480

SHQIP 512

SRPSKI 545

УКРАЇНСЬКА 578

4

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Protection cap for nose trimmer attachment

(specic types only)

2 Click-on nose trimmer attachment

(specic types only)

3 Comb for beard styler attachment

(specic types only)

4 Click-on beard styler attachment

(specic types only)

5 Click-on trimmer attachment

(specic types only)

6 Protection cap for shaving unit

(specic types only)

7 Click-on shaving unit

8 On/off button

9 Turbo button (specic types only)

10 Handle

11 Socket for small plug

12 Battery charge indicator with 1 light

13 Battery charge indicator with 3 lights

14 Travel lock symbol

15 Replacement reminder

16 Cleaning reminder

17 Cleaning cartridge for SmartClean system

18 SmartClean system (specic types only)

19 Cap of SmartClean system

20 On/off button

21 Battery symbol

22 Cleaning symbol

ENGLISH

23 Replacement symbol

24 Ready symbol

25 Adapter

26 Small plug

27 Pouch (specic types only)

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Important safety information

Read this important information carefully before you

use the appliance and its accessories and save it for

future reference. The accessories supplied may vary

for different products.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug, as

this causes a hazardous situation.

- This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use

of the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not

be made by children without supervision.

- Always unplug the shaver before you clean it

under the tap.

- Always check the appliance before you use it. Do

not use the appliance if it is damaged, as this may

cause injury. Always replace a damaged part with

one of the original type.

ENGLISH 5

Caution

- Never immerse the cleaning system or the

charging stand in water and do not rinse it under

the tap.

- Never immerse the shaver in water. Do not use

the shaver in the bath or in the shower.

- Never use water hotter than 80°C to rinse the

shaver.

- Only use this appliance for its intended purpose as

shown in the user manual.

- Do not use the adapter in or near wall sockets

that contain or have contained an electric air

freshener to prevent irreparable damage to the

adapter

- For hygienic reasons, the appliance should only be

used by one person.

- Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as petrol

or acetone to clean the appliance.

- If your shaver comes with a cleaning system,

always use the original Philips cleaning uid

(cartridge or bottle, depending on the type of

cleaning system).

- Always place the cleaning system on a stable, level

and horizontal surface to prevent leakage.

- If your cleaning system uses a cleaning cartridge,

always make sure that the cartridge compartment

is closed before you use the cleaning system to

clean or charge the shaver.

- When the cleaning system is ready for use, do not

move it to prevent leakage of cleaning uid.

- Water may drip from the socket at the bottom

of the shaver when you rinse it. This is normal

ENGLISH6

and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

Electromagnetic elds (EMF)

- This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic elds.

General

- This shaver can be safely cleaned under the tap.

- The appliance is suitable for mains voltages ranging

from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe

low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

The display

Charging

Battery charge indicator with 3 lights

- Charging takes approx. 1 hour

- Quick charge (specic types only): When the

appliance is connected to the mains, the lights of

the battery charge indicator light up one after the

other continuously. When the appliance contains

enough energy for one shave, the bottom light of

the battery charge indicator ashes slowly.

- If you leave the appliance connected to the

mains, the charging process continues. To indicate

that the appliance is charging, rst the bottom

light ashes and then lights up continuously.

Then the second light ashes and then lights up

continuously, and so on until the appliance is fully

charged.

ENGLISH 7

Battery charge indicator with 1 light

- Charging takes approx. 1 hour.

- Quick charge (specic types only): When the

appliance does not contain enough energy for one

shave, the battery charge indicator ashes quickly.

When the battery charge indicator starts ashing

slowly, the appliance contains enough energy for

one shave .

- If you leave the appliance connected to the mains,

the charging process continues. To indicate that

the appliance is charging, the battery charge

indicator ashes slowly.

Battery fully charged

Note: You can also use this appliance directly from the

mains.

Note: When the battery is full, the display switches off

automatically after 30 minutes.

When the battery is fully charged, all lights of the

battery charge indicator light up continuously.

- Battery charge indicator with 3 lights

- Battery charge indicator with 1 light

ENGLISH8

Battery low

When the battery is almost empty, the battery

charge indicator ashes orange.

- Battery charge indicator with 3 lights

- Battery charge indicator with 1 light

Remaining battery capacity

Battery charge indicator with 3 lights

- The remaining battery capacity is indicated by the

lights of the battery charge indicator that light up

continuously.

Cleaning reminder

For optimal shaving performance, we advise you to

clean the shaver after every use.

- When you switch off the shaver, the cleaning

reminder ashes to remind you to clean the

shaver.

ENGLISH 9

Travel lock

You can lock the shaver when you are going to

travel. The travel lock prevents the shaver from being

switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

- While you activate the travel lock, the travel lock

symbol lights up continuously. When the travel

lock is activated, the travel lock symbol ashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

- The travel lock symbol ashes and then lights up

continuously.

The shaver is now ready for use again.

Replacing shaving heads

For maximum shaving performance, we advise

you to replace the shaving heads every two years.

- The appliance is equipped with a replacement

reminder which reminds you to replace the

shaving heads. The replacement reminder lights up

white continuously.

Note: After replacing the shaving heads, you need to

reset the replacement reminder by pressing the on/off

button for 7 seconds.

3 sec.

ENGLISH10

Turbo setting (specic types only)

- The appliance is equipped with a Turbo or Turbo+

setting. This setting is intended for quicker and

more intense shaving and makes hard-to-reach

areas easier to shave.

Activating the Turbo setting

1 To activate the Turbo setting, press the Turbo

button once.

Deactivating the Turbo setting

1 To deactivate the Turbo setting, simply press

the Turbo button once again.

Charging

Charging takes approx. 1 hour.

Note: You can also use this appliance directly from the

mains.

Charge the shaver before you use it for the rst

time and when the display indicates that the battery

is almost empty.

Charging with the adapter

1 Insert the small plug into the appliance and put

the adapter in the wall socket.

ENGLISH 11

Charging in the SmartClean system

(specic types only)

1 Put the small plug in the SmartClean system.

2 Put the adapter in the wall socket.

3 Press down the top cap to be able to place the

shaver in the holder (‘click’).

4 Hold the shaver upside down above the holder.

Make sure the front of the shaver points

towards the SmartClean system.

5 Place the shaver in the holder, tilt the shaver

backwards and press down the top cap to

connect the shaver (‘click’).

- The battery symbol ashes slowly to indicate the

shaver is charging.

Using the shaver

Switching the appliance on and off

1 To switch on the appliance, press the on/off

button once.

2 To switch off the appliance, press the on/off

button once.

- Battery charge indicator with 3 lights: The display

lights up for a few seconds to show the remaining

battery status.

ENGLISH12

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times

a week) with this shaver for a period of 3 weeks to

allow your skin to adapt to the new shaver.

Note: You can also use the shaver directly from the

mains.

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

3 Clean the shaver after use (see chapter

‘Cleaning and maintenance’).

Turbo setting (specic types only)

The appliance is equipped with a Turbo or Turbo+

setting for easy shaving of hard-to reach areas.

1 Switch on the shaver.

2 Press the Turbo button once to switch on the

Turbo setting if you want to shave hard-to-

reach areas more quickly.

3 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

4 To deactivate the Turbo setting simply press

the Turbo button once.

ENGLISH 13

Using the click-on attachments

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Removing or attaching the click-on

attachments

1 Make sure the appliance is switched off.

2 Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you pull it off

the appliance.

3 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

Using the trimmer attachment

You can use the trimmer attachment to groom

your sideburns and moustache.

1 Make sure the appliance is switched off.

2 Insert the lug of the attachment into the slot

in the top of the shaver. Then press down

the trimmer attachment to attach it to the

appliance (‘click’).

3 Switch on the appliance.

4 You can now start trimming.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

ENGLISH14

Using the beard styler attachment

1 Make sure the appliance is switched off.

2 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

Using the beard styler attachment with

comb

You can use the beard styler attachment with the

comb attached to style your beard at one xed

setting, but also at different length settings.

You can use it also to pre-trim any long hairs before

shaving to have a more comfortable shave.

The hair length settings on the beard styler

attachment correspond to the remaining hair length

after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding

grooves on both sides of the attachment

(‘click’).

2 Press the length selector and then push it

to the left or right to select the desired hair

length setting.

3 Switch on the appliance.

4 You can now start styling your beard by

moving the attachment upwards with gentle

pressure making sure the front of the comb is

in full contact with the skin.

5 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

2

1

ENGLISH 15

Using the beard styler attachment without

comb

You can use the beard styler attachment without the

comb to contour your beard, moustache, sideburns

or neckline to a length of 0.5mm.

1 Pull the comb off the attachment.

Note: Grab the comb in the centre to pull it off the

attachment. Do not pull at the sides of the comb.

2 Switch on the appliance.

3 You can now start contouring your beard,

moustache, sideburns or neckline by moving

the styler downwards with gentle pressure

while holding it perpendicular to the skin.

4 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Using the nose trimmer attachment

You can use the nose trimmer attachment to trim

your nose hair.

Make sure your nostrils are clean.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Switch on the appliance.

3 Carefully insert the attachment into one of

your nostrils.

Do not insert the attachment more than 0.5cm

into your nostrils.

ENGLISH16

4 Slowly move the attachment around to remove

all unwanted hairs in your nostrils.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Trimming ear hair

You can use the nose trimmer attachment to trim

your ear hair. Make sure your outer ear channels are

clean and free from wax.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Switch on the appliance.

3 Slowly move the attachment along the rim of

the ear to remove hairs that stick out beyond

the rim.

4 Insert the attachment into the outer ear

channel.

Do not insert the attachment more than 0.5cm

into your ear channel, as this could damage the

eardrum.

5 Slowly turn the attachment around to remove

all unwanted hairs from your outer ear

channel.

6 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

ENGLISH 17

Cleaning and maintenance

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Cleaning the shaver in the SmartClean

system (specic types only)

Do n ot tilt the SmartClean system to prevent

leakage.

Note: Hold the SmartClean system while you prepare

it for use.

Note: If you clean the shaver in the SmartClean

system once a week, the SmartClean cartridge will last

approximately three months.

Preparing the SmartClean system for use

1 Put the small plug in the back of the

SmartClean system.

2 Put the adapter in the wall socket.

3 Press the button on the side of the SmartClean

system and lift the top part of the SmartClean

system.

4 Pull the seal off the cleaning cartridge.

5 Place the cleaning cartridge in the SmartClean

system.

1

2

ENGLISH18

6 Push the top part of the SmartClean system

back down (‘click’).

Using the SmartClean system

Always make sure to shake excess water off the

shaver before you place it in the SmartClean

system.

1 Press down the top cap to be able to place the

shaver in the holder (‘click’).

2 Hold the shaver upside down above the holder.

Make sure the front of the shaver points

towards the SmartClean system.

3 Place the shaver in the holder, tilt the shaver

backwards and press down the top cap to

connect the shaver (‘click’).

- The battery symbol ashes slowly to indicate that

the shaver is charging.

ENGLISH 19

4 Press the on/off button on the SmartClean

system to start the cleaning program.

- During the cleaning program (which takes approx.

10 minutes), the cleaning symbol ashes.

- When the cleaning program has been completed,

the ready symbol lights up continuously.

- The battery symbol lights up continuously to

indicate that the shaver is fully charged. This takes

approx. 1 hour.

Note: If you press the on/off button of the

SmartClean system during the cleaning program, the

program aborts. In this case, the cleaning symbol stops

ashing.

Note: If you remove the adapter from the wall socket

during the cleaning program, the program aborts.

Note: 30 minutes after the charging phase has been

completed, the SmartClean system switches off

automatically.

5 To let the shaver dry, you can leave it in the

SmartClean system until your next shave.

You can also remove the shaver from the

SmartClean system, shake off excess water,

open the shaving unit and let the shaver air dry.

Replacing the cartridge of the SmartClean

System

Replace the cleaning cartridge when the

replacement symbol ashes orange or when you are

no longer satised with the cleaning result.

If you clean the shaver in the SmartClean system

once a week, the SmartClean cartridge will last

approximately three months

ENGLISH20

Pagina se încarcă ...

Philips S5510/45 Manual de utilizare

Philips S5510/45 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente