Husqvarna 360BT Manual de utilizare

360BT, 570BTS, 580BTS

EN Operator's manual 2-18

BG Ръководство за експлоатация 19-37

CS Návod k použití 38-53

DA Brugsanvisning 54-69

DE Bedienungsanweisung 70-86

EL Οδηγίες χρήσης 87-104

ES Manual de usuario 105-122

ET Kasutusjuhend 123-138

FI Käyttöohje 139-154

FR Manuel d'utilisation 155-172

HR Priručnik za korištenje 173-188

HU Használati utasítás 189-205

IT Manuale dell'operatore 206-223

LT Operatoriaus vadovas 224-239

LV Lietošanas pamācība 240-256

NL Gebruiksaanwĳzing 257-273

NO Bruksanvisning 274-288

PL Instrukcja obsługi 289-306

PT Manual do utilizador 307-324

RO Instrucţiuni de utilizare 325-341

RU Руководство по эксплуатации 342-360

SK Návod na obsluhu 361-377

SL Navodila za uporabo 378-393

SV Bruksanvisning 394-409

TR Kullanım kılavuzu 410-425

UK Посібник користувача 426-443

Contents

Introduction............................................................... 2

Safety........................................................................4

Assembly.................................................................. 7

Operation.................................................................. 8

Maintenance........................................................... 11

Troubleshooting...................................................... 14

Transportation and storage.....................................15

Technical data.........................................................16

Declaration of Conformity....................................... 17

Introduction

Product description

This product is a backpack blower with a fuel engine.

We have a policy of continuous product development

and therefore reserve the right to modify the design

and appearance of products without prior notice.

Intended use

Use the product to blow leaves and other unwanted

material from areas such as lawns, pathways and

asphalt roads.

Product overview (360BT)

11

5

1

26

7

28

2

15

19

16

21

22

20

23

22

18

3

4

17

24

25

12

14

10

6

12 13

89

27

1. Frame

2. Harness

3. Engine cover

4. Fan cover

5. Air intake screen

6. Fan

7. Air filter

8. Starter rope handle

9. Fuel tank

10. Pad

11. Spark plug

12. Vibration damping system

13. Choke control

14. Control handle

15. Start/stop switch with throttle control

16. Throttle trigger

17. Pipe angle

18. Clamp

19. Flexible hose

20. Control pipe

21967 - 001 - 20.01.2023

21. Cable clamp

22. Intermediate pipe

23. Blower nozzle

24. Operator's manual

25. Combination wrench

26. Air purge bulb

27. Idle speed screw

28. Handlebar (accessory)

Product overview (570BTS, 580BTS)

27

26

34

17

19 18

2

15

14 29

23

22

16

20

21

19

9

8

24

25

28

2

7

1

511

10

12 13

6

12

1. Frame

2. Harness

3. Engine cover

4. Fan cover

5. Air intake screen

6. Fan

7. Air filter

8. Starter rope handle

9. Fuel tank

10. Hip pad

11. Spark plug

12. Vibration damping system

13. Choke control

14. Control handle

15. Stop switch with throttle control

16. Throttle trigger

17. Pipe angle

18. Clamp

19. Flexible hose

20. Control pipe

21. Cable clamp

22. Intermediate pipe

23. Blower nozzle

24. Operator's manual

25. Combination wrench

26. Air purge bulb

27. Idle speed screw

28. Handlebar (accessory)

29. Flat nozzle (accessory)

Symbols on the product

WARNING! This product can be

dangerous and cause serious injury or

death to the operator or others. Be

careful and use the product correctly.

Read the operator's manual carefully

and make sure that you understand the

instructions before use.

1967 - 001 - 20.01.2023 3

Use approved hearing protection

and approved eye protection. If the

environment contains dust, use a

breathing mask.

Use approved protective gloves.

Mixture of gasoline and two-stroke oil.

Air purge bulb.

Keep all body parts away from hot

surfaces.

Choke, open position.

Choke, closed position.

This product complies with applicable

EC Directives.

This product conforms to applicable UK

regulations.

Noise emission to the environment

label as per EU and UK directives

and regulations, and New South

Wales legislation "Protection of

the Environment Operations (Noise

Control) Regulation 2017". The

guaranteed sound power level of the

product is specified in

Technical data

on page 16

and on the label.

Look out for thrown objects.

Thrown objects can cause

serious injury. Use personal

protective equipment.

Keep a safety distance at a

minimum of 15 m to persons

or animals.

yyyywwxxxxx

The rating plate shows the

serial number. yyyy is the

production year and ww is

the production week.

Note: Other symbols/decals on the product refer

to certification requirements for other commercial

areas.

Euro V Emissions

WARNING: Tampering with the

engine voids the EU type-approval of

this product.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not

from the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not

from the manufacturer or not approved by the

manufacturer.

• the product is not repaired at an approved

service center or by an approved authority.

Safety

Safety definitions

The definitions below give the level of severity for

each signal word.

WARNING: Injury to persons.

CAUTION: Damage to the product.

Note: This information makes the product easier

to use.

General safety instructions

WARNING: Read the warning

instructions that follow before you use

the product.

• Do not do changes to the product without

approval from the manufacturer and always

41967 - 001 - 20.01.2023

use original accessories. Modifications and/or

accessories that are not approved can result in

serious injury or the death of the operator or

others.

• Do not use a damaged product. Do the safety

checks and maintenance given in this operator's

manual. All other maintenance must be done by

approved servicing personnel.

• All servicing and repair operations must be done

by approved servicing personnel. If a part of

the product is defective, speak to your servicing

dealer.

Safety instructions for operation

WARNING: Read the warning

instructions that follow before you use

the product.

• This product can be dangerous and cause

serious injury or death to the operator or others.

Be careful and use the product correctly.

• Do an inspection of the product before use. Refer

to

Maintenance on page 11

.

• Do not operate the product when you are tired,

ill or under the influence of alcohol or other

drugs that can decrease your vision, judgment

or coordination.

• Install all covers and guards before use. To

prevent electrical shock, make sure that the

spark plug cap and ignition cable are not

damaged.

• Do not touch the spark plug or ignition cable

when the engine is on.

• Keep a safety distance at a minimum of 15

m to persons or animals. If persons, children

or animals come nearer than 15 m, stop the

product. Point the product away from persons,

animals, open windows and other objects.

• Do not let children operate the product. Make

sure that all operators read and understand the

contents of this operator's manual.

• Keep hands or other objects away from the

blower housing during operation. Rotating parts

can cause serious injury.

• Do not use the product if the air intake screen

is not installed. Always make sure that the

air intake screen is installed and not damaged

before use.

• If an emergency occurs, release the waist belt

and chest belt of the harness and let the product

fall.

• Obey national regulations and directives.

• Keep all body parts away from hot surfaces.

• This product produces an electromagnetic field

during operation. This field may under some

circumstances interfere with active or passive

medical implants. To reduce the risk of serious or

fatal injury we recommend persons with medical

implants to consult their physician and the

medical implant manufacturer before operating

this product.

• Too much vibration can cause damage to the

circulation or the nervous system. Speak to your

physician if you have symptoms, for example

numbness, loss of feeling, tingling, pricking, pain,

loss of strength or changes in skin color in your

fingers, hands or wrists.

• Look out for thrown objects. Thrown objects can

cause serious injury.

• Do not use the product in bad weather, for

example fog, rain, strong winds and too cold

environments. To do work in bad weather can

cause tiredness and dangerous conditions.

• Make sure that you can move and keep a stable

position. Do a check of the work area for possible

obstacles, for example rocks. Be careful if you

operate the product on a slope.

• Do not put the product on the ground with the

engine on.

• Do not operate the product from high positions,

for example on a ladder.

• Make sure that you can always be heard if an

accident occurs.

• Make sure that the exhaust fume outlet is not

blocked. To prevent damage to the product, keep

obstacles at a minimum distance of 50 cm from

the exhaust fume outlet.

• Do not start the product indoors, in bad airflow

or near flammable material. The engine exhaust

fumes contain carbon monoxide, which can

cause carbon monoxide poisoning. The engine

exhaust fumes are hot and can contain sparks

which can start a fire.

Personal protective equipment

WARNING: Read the warning

instructions that follow before you use

the product.

• Use approved personal protective equipment

when you use the product. Personal protective

equipment cannot fully prevent injury but it can

decrease the degree of injury. Speak to your

dealer for more information.

• Use approved hearing protection. Long-term

exposure to noise can result in permanent

hearing damage.

• Use approved eye protection. If you use a visor,

you must also use approved protective goggles.

Approved protective goggles must agree with the

ANSI Z87.1 standard in the USA or EN 166 in

EU countries.

• Use protective gloves during operation and

maintenance.

• Use protective boots or shoes with non-slip

soles.

• Use clothing of strong fabric and of full length.

Do not use jewelry or open shoes. To decrease

the risk on injury, your clothing must be close-

1967 - 001 - 20.01.2023 5

fitting but not limit your movements. Put your hair

above your shoulders to prevent that your hair

enters rotating parts or catches on branches.

• Use breathing protection when there is a risk of

dust.

• Keep first aid equipment near.

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use

the product.

• Do not use a product with defective safety

devices.

• Do a check of the safety devices regularly. Refer

to

Maintenance on page 11

.

• If the safety devices are defective, speak to your

Husqvarna servicing dealer.

To do a check of the muffler

WARNING: Do not use a product

with a defective muffler.

WARNING: The muffler becomes

very hot during and after operation, also

at idle speed. Use protective gloves to

prevent burn injuries.

WARNING: The inner side of the

muffler contains chemicals that may be

carcinogenic. Do not touch the muffler if

it is damaged.

• Regularly do a visual check of the muffler. The

muffler keeps noise levels to a minimum and

sends exhaust fumes away from the operator.

Refer to

To do maintenance on the muffler on

page 12

.

To do a check of the vibration damping system

1. Make sure that there are no cracks or

deformation on the vibration damping units.

2. Make sure that the vibration damping units are

correctly attached to the engine unit and handle

unit.

Refer to

Product overview (360BT) on page 2

for information about where the vibration damping

system is on your product.

To do a check of the start/stop switch

1. Use the start/stop switch to stop the engine.

2. Make sure that the engine stops fully.

To see where the start/stop switch is on your

product, refer to

Product overview (360BT) on page

2

.

Harness safety

• Make sure that the waist belt is attached and

correctly adjusted. Loose ends of the harness

can enter rotating parts and cause damage to

the fan. If the fan is damaged, loose parts of the

product can eject and cause injury or damage.

Fuel safety

WARNING: Read the warning

instructions that follow before you use

the product.

• Do not mix or add the fuel indoors or near a heat

source.

• Do not start the product if there is fuel or oil on

the product or on your body.

• Do not start the product if the engine has a fuel

leak. Examine the engine for fuel leaks regularly.

• Always be careful with fuel. Fuel is flammable

and the fuel fumes are explosive and can cause

serious injury or death.

• Do not breathe in the fuel fumes, it can cause

injury. Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put the product or a fuel container near

warm objects, an open flame, a spark or a pilot

light.

• Always use approved containers for storage and

transportation of fuel.

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you use

the product.

• Stop the engine, remove the spark plug and let

the engine become cool before maintenance and

assembly.

• A blocked spark arrestor screen causes the

engine to become too hot which causes damage

to the engine.

61967 - 001 - 20.01.2023

Assembly

Introduction

WARNING: Read and understand

the safety chapter before you assemble

the product.

To assemble the blower pipe and the

control handle on the product

1. Attach the flexible hose (A) to the pipe angle and

the control pipe (B) with the clamps (C) and (D).

B

D

A

C

Note: Lubricate the control pipe and the

flexible hose to make them more easy to

assemble.

2. Attach the handle holder (E) to the control pipe.

Align the handle holder with the flange on the

control pipe.

E

3. Adjust the position and angle of the control

handle to a safe and correct work position.

Tighten the knob.

4. Attach the cable to the flexible hose with the

cable clamp.

5. Attach the intermediate pipe to the control pipe.

Note: If it is a requirement to use a longer

circular blower pipe, an extended intermediate

pipe is available.

6. Attach the blower nozzle to the intermediate

pipe.

Note: The blower nozzle can only be installed

on the intermediate pipe.

To assemble the handlebar (optional

accessory)

1. Disassemble the intermediate pipe.

2. Remove the knob from the holder and push the

holder onto the control pipe.

3. Install the handlebar and the knob. Tighten the

knob.

4. Assemble the intermediate pipe.

To assemble the flat nozzle (optional

accessory)

The flat nozzle gives a higher air speed than the

blower nozzle.

1967 - 001 - 20.01.2023 7

• Remove the blower nozzle from the intermediate

pipe and install the flat nozzle.

Operation

Introduction

WARNING: Read and understand

the safety chapter before you use the

product.

Fuel

This product has a two-stroke engine.

CAUTION: Incorrect type of fuel can

result in engine damage. Use a mixture

of gasoline and two-stroke oil.

Premixed fuel

• Use Husqvarna premixed alkylate fuel for

best performance and extension of the engine

life. This fuel contains less harmful chemicals

compared to regular fuel, which decreases

harmful exhaust fumes. The quantity of remains

after combustion is lower with this fuel, which

keeps the components of the engine more clean.

To mix fuel

Gasoline

• Use good quality unleaded gasoline with a

maximum of 10% ethanol contents.

CAUTION: Do not use gasoline

with an octane grade less than 90

RON/87 AKI. Use of a lower octane

grade can cause engine knocking,

which causes engine damages.

Two-stroke oil

• For best results and performance use Husqvarna

two-stroke oil.

• If Husqvarna two-stroke oil is not available, use

a two-stroke oil of good quality for air-cooled

engines. Speak to your servicing dealer to select

the correct oil.

CAUTION: Do not use two-

stroke oil for water-cooled outboard

engines, also referred to as outboard

oil. Do not use oil for four-stroke

engines.

To mix gasoline and two-stroke oil

Gasoline, liter Two-stroke

oil, liter

2% (50:1)

5 0.10

10 0.20

15 0.30

20 0.40

CAUTION: Small errors can

influence the ratio of the mixture

drastically when you mix small quantities

of fuel. Measure the quantity of oil

carefully and make sure that you get the

correct mixture.

1. Fill half the quantity of gasoline in a clean

container for fuel.

2. Add the full quantity of oil.

3. Shake the fuel mixture.

81967 - 001 - 20.01.2023

4. Add the remaining quantity of gasoline to the

container.

5. Carefully shake the fuel mixture.

CAUTION: Do not mix fuel for more

than 1 month at a time.

To fill the fuel tank

WARNING: Obey the procedure

that follows for your safety.

1. Stop the engine and let the engine become cool.

2. Clean the area around the fuel tank cap.

3. Shake the container and make sure that the fuel

is fully mixed.

4. Remove the fuel tank cap slowly to release the

pressure.

5. Fill the fuel tank.

CAUTION: Make sure that there

is not too much fuel in the fuel tank.

The fuel expands when it becomes

hot.

6. Tighten the fuel tank cap carefully.

7. Clean fuel spillage on and around the product.

8. Move the product 3 m/10 ft or more away from

the refueling area and fuel source before you

start the engine.

Note: To see where the fuel tank is on your

product, refer to

Product overview (360BT) on page

2

and

Product overview (570BTS, 580BTS) on page

3

.

To start the product

1. For 360BT. If the engine is cold, push the choke

lever to the closed choke position. Refer to

Symbols on the product on page 3

.

2. For 570BTS and 580BTS. If the engine is

cold, push the choke lever to the closed choke

position. Refer to

Symbols on the product on

page 3

.

3. Push the air purge bulb again and again until fuel

starts to fill the air purge bulb. It is not necessary

to fill the air purge bulb fully.

4. Push the start/stop switch with throttle control to

the 1/3 speed position. Refer to

To operate the

throttle control/stop switch on page 10

.

5. Put the product on a flat surface on the ground.

6. Hold the product with the left hand.

CAUTION: Do not use your feet

to hold the product.

7. Pull the starter rope handle slowly until

resistance occurs.

1967 - 001 - 20.01.2023 9

8. Pull the starter rope handle quickly with the right

hand. Pull the starter rope handle again and

again until the engine starts.

Note: Do not pull the starter rope handle to full

extension and do not let go of the starter rope

handle.

9. If the engine is cold, push the choke lever to

the open choke position gradually until the choke

lever stops.

10. If the engine is cold, let the engine operate for

2-3 minutes to become warm before operation.

WARNING: Air is released

when the engine is started and when

the product is set at idle speed. Do

not let persons to come near the

product or the blower tube.

To operate the throttle control/stop

switch

A

B

C

D

• Apply full throttle (A).

• Apply 1/3 speed (B).

• Apply idle speed (C).

• Stop the product (D).

To operate the product

• This blower is a backpack type, and is carried

using a shoulder harness while operating. It is

operated and controlled with the handle on the

tube using the right hand.

• Operate the product at usual work hours. Obey

local regulations.

• Decrease the pieces of equipment and select the

correct speed for your task. Use the throttle at

lowest position possible to prevent more noise

and dust than necessary.

• Keep the blower nozzle near the ground.

Note: Husqvarna recommends that you use

the full blower nozzle extension.

• Make a note of the wind direction and operate

the product in the direction of the wind.

• Use applicable garden tools to release material

from the ground.

• In areas with dust, use spray equipment to wet

the area. This decreases the operation time.

• After operation, keep the product in storage

vertically.

To stop the product

CAUTION: Do not stop the product

at full speed.

1. Put the start/stop switch with throttle control in

the stop position. Refer to

To operate the throttle

control/stop switch on page 10

.

To adjust the harness

A correctly adjusted harness and product makes

operation easier.

1. Put on the harness of the product.

2. Tighten the side straps until the product is tight

against your body.

For 570BTS, 580BTS:

3. Put the waist belt around your waist.

4. Tighten the waist belt strap. Make sure that the

weight of the blower stays on your hips.

5. Connect the chest strap to the clip.

6. Tighten the strap.

10 1967 - 001 - 20.01.2023

Maintenance

Introduction

WARNING: Read and understand

the safety chapter before you do

maintenance on the product.

Maintenance schedule

Maintenance Daily Weekly Monthly

Clean the external surfaces. X

Make sure that the control handle operates correctly. X

Make sure that the start/stop switch operates correctly. Refer to

To do a

check of the start/stop switch on page 6

.X

Examine the engine, the fuel tank and the fuel lines for leaks. Examine the

fuel filter for contamination. Replace the fuel filter if it is necessary. X

Clean the air filter. Replace the air filter if it is necessary. X

Tighten nuts and screws. X

Examine the air intake and make sure that it is not blocked. X

Examine the starter and the starter rope for damages. X

Examine the vibration damping units for damages, cracks and deformation.

Make sure that the vibration damping units are correctly installed. X

Examine the spark plug. Refer to

To do a check of the spark plug on page

11

.X

Clean the cooling system. X

Clean the external surface of the carburetor and the area around it. X

Clean the fuel tank. X

Examine all cables and connections. X

Examine and clean the spark arrestor screen on the muffler (for products

without catalytic converter). X

Examine and clean the spark arrestor screen on the muffler (for products

with catalytic converter). X

Examine the spark plug. Replace if it is necessary. X

To adjust the idle speed

1. Make sure that the air filter is clean and that the

air filter cover is attached.

2. Adjust the idle speed with the idle speed screw.

To see where the idle speed screw is on your

product, refer to

Product overview (360BT) on

page 2

.

To do a check of the spark plug

CAUTION: Use the recommended

spark plug. Refer to

Technical data on

page 16

. An incorrect spark plug can

cause damage to the product.

1. Stop the engine and let the product become cool.

2. Clean the spark plug if it is dirty.

1967 - 001 - 20.01.2023 11

3. Make sure that the electrode gap is correct.

Refer to

Technical data on page 16

.

4. Replace the spark plug monthly or more

frequently if it is necessary.

To do maintenance on the muffler

1. Stop the engine and let the muffler become cool.

Always use protective gloves.

2. Remove the screws (A), the screws (B) and the

exhaust duct (C).

B

C

D

A

3. Remove the spark arrester screen (D) and clean

it with a wire brush. Replace the spark arrester

screen if it is damaged.

4. Remove dirt from muffler and from the exhaust

port of the cylinder with the wire brush.

5. Attach the spark arrester screen (D) and the

exhaust duct (C) with the screws (B). Tighten the

screws to 2–3 Nm.

6. Tighten the screws (A) to 8–12 Nm. Make sure

that the muffler is correctly attached to the

product.

To examine and clean the cooling

system

The cooling system includes the cooling fins on the

cylinder and the air intake screen.

1. Stop the engine.

2. Make sure that the cooling system is not dirty or

blocked. If it is necessary, clean the air intake

screen and cooling fins.

CAUTION: A dirty or blocked

cooling system can increase the

temperature of the engine and cause

damage to the product. A clogged

air intake screen decreases the blow

force.

3. Examine the cooling system for damages. Make

sure that the parts are attached correctly to the

product.

Air filter

CAUTION: Do not use a product

without an air filter or with a damaged air

filter. Dust in the air can cause damage

to the engine.

Note: An air filter that has been used for a long

time cannot be fully cleaned. Replace the air filter

regularly and always replace a defective air filter.

Note: Clean the air filter regularly from dirt and

dust. This prevents carburetor malfunctions, starting

problems, loss of engine power, wear to engine parts

and more fuel consumption than usual. Clean the air

filter at an interval of 40 hours of operation or less if

it is heavy operation conditions.

To clean the air filter (360BT)

1. Push the choke control to the closed position.

2. Remove the air filter cover (A).

3. Remove the air filter (B) from the filter frame.

AB

4. Clean the air filter with warm water with soap.

5. Clean the inner surface of the air filter cover (A)

with a brush.

6. Apply oil to the air filter. Refer to

To apply oil to

the foam air filter (360BT) on page 12

.

7. Put the air filter in the filter frame.

8. Attach the air filter cover to the product.

To apply oil to the foam air filter (360BT)

CAUTION: Always use Husqvarna

special air filter oil. Do not use other

types of oil.

WARNING: Put on protective

gloves. The air filter oil can cause skin

irritation.

12 1967 - 001 - 20.01.2023

1. Put the foam air filter in a plastic bag.

2. Put the oil in the plastic bag.

3. Rub the plastic bag to supply the oil equally

across the foam air filter.

4. Push the unwanted oil out of the foam air filter

while in the plastic bag.

To clean the air filter (570BTS, 580BTS)

CAUTION: Do not put oil on the

foam element of the air filter in 570BTS

and 580BTS.

1. Loosen the fasteners that holds the air filter

cover in position.

2. Remove the air filter cover (A).

A

B

C

3. Remove the foam filter (B) and the paper filter

(C) from the filter frame.

4. Replace the paper filter (C).

5. Clean the foam filter (B) with warm soap water.

6. Make sure that the foam filter (B) is dry.

7. Clean the inner surface of the air filter cover with

a brush (A).

To replace the harness

WARNING: A damaged harness

can make the product fall and cause

injuries. Make sure to install the clamp

correctly.

1. Stop the engine.

2. Remove the clamp from the strap.

3. Push the end of the strap through the eyelet.

4. Pull the new strap through the eyelet.

5. Put the pin into the strap to attach the clamp to

the new strap.

1967 - 001 - 20.01.2023 13

Troubleshooting

The engine is not possible to start

Check Possible

cause

Solution

Stop button. Stop position Set the stop switch to the start position.

Starter pawl/s. Blocked or

worn starter

pawl/s.

Adjust or replace the starter pawl/s.

Clean around the starter pawl/s.

Speak to an approved servicing dealer.

Fuel tank. Incorrect fuel

type.

Drain the fuel tank and use correct fuel.

Carburetor. Adjustment of

the idle speed.

Adjust the idle speed with the idle adjustment screw.

Spark (no

spark).

Spark plug

dirty or wet.

Make sure that the spark plug is dry and clean.

Electrode gap

on the spark

plug is incor-

rect.

Clean the spark plug. Make sure that the electrode gap is correct. Make

sure that the spark plug is installed with a suppressor.

Refer to technical data for the correct electrode gap.

Spark plug.

Spark plug is

loose.

Tighten the spark plug.

There is un-

wanted mate-

rial on the

spark plug

electrodes.

Make sure that the fuel mixture is correct.

Make sure that the air filter is clean.

Engine starts but stops again

Check Possible

cause

Solution

Fuel tank. Incorrect fuel

type.

Drain it and use the correct fuel.

Carburetor. Engine will not

operate cor-

rectly at idle

speed.

Speak to your servicing dealer.

Air filter. Clogged air fil-

ter.

Clean the air filter.

14 1967 - 001 - 20.01.2023

Transportation and storage

WARNING: To prevent the risk of

fire, make sure that there are no leaks or

fumes during transportation or storage.

Make sure that there is no risk of sparks

or fire.

• Empty the fuel tank before transportation or long-

term storage. Push the air purge bulb to make

sure that all fuel is removed. Discard the fuel at

an applicable disposal location.

• Make sure that the product is clean and that a full

servicing is done before long-term storage.

• Remove the spark plug and put approximately

15 ml of two-stroke oil into the cylinder. Turn the

product 3 times and install the spark plug again.

• Attach the product safely to the vehicle during

transportation.

• Keep the product in a dry, cool and clean space

with good airflow. Keep the product away from

children.

1967 - 001 - 20.01.2023 15

Technical data

360BT 570BTS 580BTS

Engine

Cylinder displacement, cm365.6 65.6 75.6

Idle speed, rpm 2000 2000 2000

Catalytic converter No No No

Ignition system

Spark plug NGK CMR7H NGK CMR7H NGK CMR7H

Electrode gap, mm 0.6–0.7 0.6–0.7 0.6–0.7

Fuel and lubrication system

Fuel tank capacity, l / cm32.2 / 2200 2.2 / 2200 2.6 / 2600

Weight

Weight without fuel, kg 10.5 11.2 11.8

Noise emissions 1

Sound power level, measured dB (A) 110 110 111

Sound power level, guaranteed LWA dB

(A) 111 110 112

Sound levels 2

Equivalent sound pressure level at the operator’s ear, measured according to EN15503 dB(A):

Equipped with blower nozzle (original) 104 103 100

Vibration levels 3

Equivalent vibration levels (ahv,eq) at han-

dles, measured according to EN 15503,

m/s22.5 1.8 1.6

Fan performance

Max. air velocity with blower nozzle, m/s 104 106 92

Air flow with blower nozzle, m3/min 18 22 26

1Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive

2000/14/EC. Reported sound power level for the machine has been measured with the original blower

nozzle that gives the highest level. The difference between guaranteed and measured sound power

is that the guaranteed sound power also includes dispersion in the measurement result and the

variations between different machines of the same model according to Directive 2000/14/EC.

2Reported data for noise pressure level has a typical statistical dispersion (standard deviation) of 1.0 dB

(A).

3Reported data for vibration level has a typical statistical dispersion (standard deviation) of 1.0 m/s2.

16 1967 - 001 - 20.01.2023

Declaration of Conformity

EC Declaration of Conformity

We, Husqvarna AB, SE-561 82 Huskvarna,

Sweden, tel: +46-36-146500, declare on our sole

responsibility that the product:

Description Backpack blower

Brand Husqvarna

Type / Model 360BT, 570BTS, 580BTS

Identification Serial numbers dating from 2022 (360BT), 2023 (570BTS, 580BTS) and onwards.

complies fully with the following EU directives and

regulations:

Regulation Description

2006/42/EC ”relating to machinery”

2014/30/EU ”relating to electromagnetic compatibility”

2000/14/EC ”relating to the noise emissions in the environment”

2011/65/EU ”on the restriction of the use of certain hazardous substances in electrical and elec-

tronic equipment”

and that the following standards and/or technical

specifications are applied: EN ISO 12100:2010,

CISPR 12:2009, EN 15503:2009+A2:2015, EN IEC

63000:2018

RISE SMP Svensk Maskinprovning AB, Box 7035,

SE-750 07 Uppsala, Sweden has performed

voluntary type examination on behalf of Husqvarna

AB.

Certificate Number: SEC/22/2566 - 360BT,

SEC/10/2276 - 570BTS, SEC/10/2277 - 580BTS

RISE SMP Svensk Maskinprovning AB, Box 7035,

SE-750 07 Uppsala, Sweden has also verified

agreement with appendix V of the council's directive

2000/14/EG.

For information relating to noise emissions, refer to

Technical data on page 16

.

Huskvarna, 2023-01-01

Stefan Holmberg, R&D Director, Technology

Management, Husqvarna AB.

Responsible for technical documentation

1967 - 001 - 20.01.2023 17

UK Declaration of Conformity

We, Husqvarna AB, SE-561 82 Huskvarna,

Sweden, tel: +46-36-146500, declare on our sole

responsibility that the product:

Description Backpack blower

Brand Husqvarna

Type / Model 360BT, 570BTS, 580BTS

Identification Serial numbers dating from 2022 (360BT), 2023 (570BTS, 580BTS) and onwards.

complies fully with the following UK regulations:

Description

The Supply of Machinery (Safety) Regulations 2008

Electromagnetic Compatibility Regulations 2016

The Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001, Schedule 8

The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regula-

tions 2012

and that the following standards and/or technical

specifications are applied: EN ISO 12100:2010,

CISPR 12:2009, EN 15503:2009+A2:2015, EN IEC

63000:2018

For information relating to noise emissions, refer to

Technical data on page 16

.

Huskvarna, 2023-01-01

Stefan Holmberg, R&D Director, Technology

Management, Husqvarna AB.

Responsible for technical documentation

UK Importer:

Husqvarna UK Ltd

Preston Road, Co. Durham

DL5 6UP

18 1967 - 001 - 20.01.2023

Съдържание

Въведение............................................................. 19

Безопасност...........................................................22

Монтаж...................................................................24

Операция............................................................... 26

Поддръжка.............................................................29

Отстраняване на проблеми..................................32

Транспорт и съхранение.......................................34

Технически характеристики..................................35

Декларация за съответствие................................37

Въведение

Описание на продукта

Този продукт е преносимо компресорно

оборудване с двигател с вътрешно горене.

Ние имаме политика на непрекъснато

усъвършенстване на продуктите и затова си

запазваме правото да променяме тяхната

конструкция и външен вид без предизвестие.

Предназначение

Използвайте продукта за събиране на листа или

други нежелани предмети от зони като морави,

пътеки и асфалтирани пътища.

Общ преглед на продукта (360BT)

11

5

1

26

7

28

2

15

19

16

21

22

20

23

22

18

3

4

17

24

25

12

14

10

6

12 13

89

27

1. Рамка

2. Самар

3. Капак на двигателя

4. Капак на вентилатора

5. Филтър на смукателния въздухопровод

6. Вентилатор

7. Въздушен филтър

8. Ръкохватка на въжето на стартера

9. Резервоар за гориво

10. Подложка

11. Запалителна свещ

12. Антивибрационна система

13. Смукач

14. Ръкохватка за управление

15. Превключвател за стартиране/спиране с

регулатор на дроселната клапа

1967 - 001 - 20.01.2023 19

16. Регулатор за газта

17. Тръбно коляно

18. Скоба

19. Мека връзка

20. Основна тръба

21. Скоба на кабел

22. Междинна тръба

23. Дюза за компресорно оборудване

24. Ръководство за оператора

25. Комбиниран гаечен ключ

26. Купол на горивната помпа

27. Винт за обороти на празен ход

28. Ръкохватка (принадлежност)

Общ преглед на продукта (570BTS, 580BTS)

27

26

34

17

19 18

2

15

14 29

23

22

16

20

21

19

9

8

24

25

28

2

7

1

511

10

12 13

6

12

1. Рамка

2. Самар

3. Капак на двигателя

4. Капак на вентилатора

5. Филтър на смукателния въздухопровод

6. Вентилатор

7. Въздушен филтър

8. Ръкохватка на въжето на стартера

9. Резервоар за гориво

10. Подложка за бедро

11. Запалителна свещ

12. Антивибрационна система

13. Смукач

14. Ръкохватка за управление

15. Превключвател за спиране с регулатор на

дроселната клапа

16. Регулатор за газта

17. Тръбно коляно

18. Скоба

19. Мека връзка

20. Основна тръба

21. Скоба на кабел

22. Междинна тръба

23. Дюза за компресорно оборудване

24. Ръководство за оператора

25. Комбиниран гаечен ключ

26. Купол на горивната помпа

27. Винт за обороти на празен ход

28. Ръкохватка (принадлежност)

29. Плосък накрайник (принадлежност)

20 1967 - 001 - 20.01.2023

Pagina se încarcă ...

Husqvarna 360BT Manual de utilizare

Husqvarna 360BT Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente