Yamaha 900SW Manual de utilizare

Categorie
Amplificatoare audio
Tip
Manual de utilizare

Acest manual este potrivit și pentru

Soavo-900SW
SUBWOOFER SYSTEM
UB
OWNER’S MANUAL
i En
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
IMPORTANT
Please record the serial number of this system in the
space below.
Model:
Serial No.:
The serial number is located on the rear of the main
unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Explanation of Graphical Symbols
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
Be sure to allow spaces of at least 20 cm above,
behind and on both sides of the unit.
Do not place the following objects on the unit:
A vessel with water in it.
If the vessel falls by vibrations and water spills, it
may cause damage to the unit, and/or you may get an
electric shock.
ii En
We Want You Listening For A
Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion – and, most importantly,
without affecting your sensitive hearing.
Since hearing damage from loud
sounds is often undetectable until it is
too late, YAMAHA and the
Electronic Industries Association’s
Consumer Electronics Group
recommend you to avoid prolonged
exposure from excessive volume
levels.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE : DO NOT MODIFY
THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2 IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could
void your FCC authorization to use this product in
the USA.
3 NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result
in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
iii En
Thank you for selecting this YAMAHA subwoofer system.
Please read the following operating precautions before use.
YAMAHA will not be held responsible for any damage and/or
injury caused by not following the cautions below.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a cool, dry, clean place - away from
windows, heat sources, sources of excessive vibration, dust,
moisture and cold. Avoid sources of humming (transformers,
motors).
3 Never open the cabinet. If something drops into the set, contact
your dealer.
4 The voltage to be used must be the same as that specified on
the rear panel. Using this unit with a higher voltage than
specified is dangerous and may cause a fire and/or electric
shock.
5 To reduce the risk or fire or electric shock, do not expose this
unit to rain or moisture.
6 Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and the
wires connected to other equipments. Never pull the wires
themselves.
7 When not planning to use this unit for a long period (ie.,
vacation, etc.), disconnect the AC power plug from the wall
outlet.
8 Since this unit has a built-in power amplifier, heat will radiate
from the rear panel. Place the unit apart from the walls,
allowing at least 20 cm of space above, behind and on both
sides of the unit to prevent fire or damage. Furthermore, do not
position with the rear panel facing down on the floor or other
surfaces.
9 Do not cover the rear panel of this unit with a newspaper, a
tablecloth, a curtain, etc. in order not to obstruct heat radiation.
If the temperature inside the unit rises, it may cause fire,
damage to the unit and/or personal injury.
10 Do not place the following objects on this unit:
- Glass, china, small metallic etc.
If glass etc. falls by vibrations and breaks, it may cause bodily
injury.
- A burning candle etc.
If the candle falls by vibrations, it may cause fire and bodily
injury.
- A vessel with water in it
If the vessel falls by vibrations and water spills, it may cause
damage to the speaker, and/or you may get an electric shock.
11 Do not place this unit where foreign objects such as water drips
might fall. It might cause a fire, damage to this unit, and/or
personal injury.
12 Never put a hand or a foreign object into the YST port located
on the front side of this unit. When moving this unit, do not
hold the port as it might cause personal injury and/or damage
to this unit.
13 Never place a fragile object near the YST port of this unit. If
the object falls or drops by the air pressure, it may cause
damage to the unit and/or personal injury.
14 Never open the cabinet. It might cause an electric shock since
this unit uses a high voltage. It might also cause personal injury
and/or damage to this unit.
15 When using a humidifier, be sure to avoid condensation inside
this unit by allowing enough spaces around this unit or
avoiding excess humidification. Condensation might cause a
fire, damage to this unit, and/or electric shock.
16 Super-bass frequencies reproduced by this unit may cause a
turntable to generate a howling sound. In such a case, move
this unit away from the turntable.
17 This unit may be damaged if certain sounds are continuously
output at high volume level. For example, if 20 Hz-50 Hz sine
waves from a test disc, bass sounds from electronic
instruments, etc. are continuously output, or when the stylus of
a turntable touches the surface of a disc, reduce the volume
level to prevent this unit from being damaged.
18 If you hear distorted noise (i.e., unnatural, intermittent
“rapping” or “hammering” sounds) coming from this unit,
reduce the volume level. Extremely loud playing of a movie
soundtrack’s low frequency, bass-heavy sounds or similarly
loud popular music passages can damage this speaker system.
19 Vibration generated by super-bass frequencies may distort
images on a TV. In such a case, move this unit away from the
TV set.
20 Do not attempt to clean this unit with chemical solvents as this
might damage the finish. Use a clean, dry cloth.
21 Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that the
unit is faulty.
22 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
23 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
24 Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or installation of
speakers.
CAUTION: Read this before operating your unit.
This unit features a magnetically shielded design, but
there is still a chance that placing it too close to a TV set
might impair picture color. Should this happen, move
this unit away from the TV set.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. In this state, this unit is designed
to consume a very small quantity of power.
1 En
VOLTAGE SELECTOR
(Asia and General models only)
The voltage selector switch on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging this unit into the AC main supply. Voltages
are 110/120/220/230-240 V AC, 50/60 Hz.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
GETTING STARTED ............................................. 2
Features .................................................................. 2
About this manual .................................................. 2
Supplied accessories ............................................. 2
Controls and functions........................................... 3
Preparing the remote control................................. 5
PLACEMENT ........................................................ 6
CONNECTIONS .................................................... 7
Connecting to the amplifier equipped
with subwoofer (line out) terminal(s)........................ 7
Connecting to an amplifier not equipped
with a subwoofer (line out) terminal
........................ 9
Connecting to the ground terminal ..................... 12
Connecting the power cable ................................ 12
USING THIS UNIT ............................................... 13
Adjusting the sound balance............................... 13
Storing the sound balance settings .................... 14
Setting the sleep timer ......................................... 14
Operating the power of this unit using
the remote control of your amplifier ................... 15
Frequency response............................................. 16
Advanced Yamaha
Active Servo Technology II ............................... 17
TROUBLESHOOTING ........................................ 18
SPECIFICATIONS .............................................. 19
IMPORTANT:
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured
BLUE must be connected to the terminal which is
marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected
to the terminal which is marked with the letter L or
coloured RED. Making sure that neither core is
connected to the earth terminal of the three pin plug.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug
to wide slot and fully insert.
This Class B digital apparatus complies with
Canadian ICES-003.
CONTENTS
1
2
2 En
High 600 W dynamic power
L.F.E input terminal
Sleep timer
Remote control capability
You can make setting changes and adjustments for this
unit by using the remote control from your listening
position.
Advanced Yamaha Active Servo Technology II
This unit employs Advanced Yamaha Active Servo
Technology II which Yamaha has developed for
reproducing higher quality super-bass sound.
Two input connections
This unit can be easily added to your existing audio
system by connecting to either the speaker terminals or
the line output (pin jack) terminals of the amplifier.
Optimum bass sounds with various settings
Setting high cut and phase keeps the optimum sound
quality balance between the front speakers and this unit.
B.A.S.S. mode button
This unit is equipped with the B.A.S.S. mode button so
that you can enjoy bass sound that matches any kind of
source.
In this manual, operations that can be performed using either the front panel of this unit or the remote control are
explained using the remote control.
y indicates a tip for your operation.
Notes contain important information about safety and operating instructions.
Check that you have received all of the following parts.
GETTING STARTED
Features
About this manual
Supplied accessories
Power cable
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
Remote control
Batteries (2)
(AA, R6, UM-3)
3 En
GETTING STARTED
Front panel
1 Remote control sensor
Receives signals from the remote control.
2 STANDBY/ON indicator
Green: Lights up when this unit is on.
Red: Lights up when this unit is in the standby mode.
Orange: Lights up when the sleep timer is on.
3 PHASE indicator
Green
: Lights up when the phase is set in the reverse mode.
Red: Lights up when the phase is set in the regular mode.
4 STANDBY/ON switch
Turns on or sets this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power.
5 H-CUT control
Adjusts the high frequency cut off point depending on the
connected front speakers or your preference (see page 13).
6 VOLUME control
Adjusts the volume level. Turn the control clockwise to
increase the volume, counterclockwise to decrease the
volume.
7 B.A.S.S. indicators
Light up to indicate the currently selected B.A.S.S.
number (1, 2 or 3) (see page 13).
8 PRESET indicators
Light up to indicate the currently selected PRESET
number (1, 2 or 3) (see page 14).
If you set this unit to the standby mode when one of the
PRESET indicators is lit, no PRESET indicator lights up
when you turn on this unit next time.
The PRESET indicator turns off when you press any
button other than PRESET 1, 2, or 3, or when you
operate any other function of this unit.
Controls and functions
H-CUT
SUBWOOFER SYSTEM Soavo-900SW
STANDBY
/ON
STANDBY
/ON
PHASE
123123
B.A.S.S.
PRESET
140Hz
40Hz
VOLUME
10
0
1
2
3
456
7
8
Note
H-CUT
140Hz
40Hz
One graduation
of this control
represents 10 Hz.
Notes
4 En
GETTING STARTED
Rear panel
1 GND terminal
See page 12 for connection information.
2 INPUT 3 terminals
See pages 7 - 8 for connection information.
3 INPUT 2 (LFE) terminals
See page 8 for connection information.
4 OUTPUT terminals
See page 10 for connection information.
5 INPUT 1 terminals
See pages 10 - 11 for connection information.
6 AC IN
Connects the supplied power cable (see page 12).
7 POWER switch
Switches the power (ON/OFF) of this unit.
Normally, set this switch to the ON position. When this
unit is not used for a long period of time, set the switch to
the OFF position.
Remote control
1 STANDBY
Sets this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power.
2 POWER
Turns on this unit.
3 B.A.S.S.
Selects a mode that is suitable for the source.
Each time you press B.A.S.S., the B.A.S.S. indicator
changes between 1, 2, and 3.
4 PRESET
Stores or recalls the B.A.S.S., volume, high-cut frequency
and phase settings (see page 14).
5 HIGH CUT /
Adjusts the high frequency cut off point depending on the
connected front speakers or your preference (see page 13).
6 SLEEP
Sets the sleep timer (see page 14).
7 PHASE
Switches the phase mode.
Normally, set this unit to the reverse position. However,
according to your speaker systems or the listening
condition, there may be cases when better sound quality is
obtained by setting this switch to the normal position.
Select the better position by monitoring the sound.
8 MEMORY
Stores the B.A.S.S., volume, high-cut frequency and phase
settings (see page 14).
9 VOLUME /
Adjusts the volume of this unit.
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
INPUT
3
INPUT
2
INPUT 1
L
L
L
R
R
R
LR
MONO
POWER
ON
OFF
Note
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
1
2
3
4
59
8
7
6
5 En
GETTING STARTED
Installing the batteries in the remote
control
1 Press the mark on the battery cover and
open the cover.
2 Insert the two supplied type AA, R6, UM-3
batteries following the indications (+/–)
inside the battery compartment.
3 Close the battery cover.
Replacing the batteries
Change all of the batteries if you notice conditions such as
the operation range of the remote control decreases.
Do not use an old battery together with a new one.
Do not use different types of batteries (for example,
alkaline and manganese) together. Each type of battery
has its own characteristics even if they are similar in
shape.
If the batteries run out, immediately remove them from
the remote control to prevent an explosion or acid leak.
Dispose of the batteries according to the regional
regulations.
If a battery starts leaking, dispose of it immediately. Be
careful not to let leaking battery acid come into contact
with your skin or clothing. Before inserting new
batteries, wipe the compartment clean.
Using the remote control
The remote control transmits a directional infrared ray. Be
sure to aim the remote control directly at the remote control
sensor on the main unit during operation.
Handling the remote control
Be careful not to spill liquid on the remote control.
Be careful not to drop the remote control.
Do not leave the remote control in the following places:
– hot or humid places, such as near a heater or in a
bathroom
– extremely cold places
– dusty places
Preparing the remote control
Notes
3
1
2
Remote control
sensor
Approximately
6 m (20 ft)
6 En
The position of the subwoofer is not so critical because bass sound is not highly directional. For a sonorous sound field,
the use of two subwoofers is recommended, although you can obtain a good effect with one subwoofer. ( : subwoofer,
: front speaker)
When using one subwoofer
Place the subwoofer on the outside of either the right or the
left front speaker.
y
If the subwoofer is placed directly facing the wall, the bass
sound may lessen because the sound from the subwoofer
and the sound reflected by the wall may cancel each other
out. To prevent this from happening, face the subwoofer
obliquely to the wall ( or ).
When using two subwoofers
Place the subwoofers on the outside of each front speaker.
PLACEMENT
A
A B
B
7 En
See pages 7 - 8 when your amplifier has subwoofer (line out) terminal(s), or see pages 9 - 11 when your amplifier has no
subwoofer (line out) terminal.
Do not connect the power cord of this unit and other components into an AC outlet until all connections between
components are completed.
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. Also, refer to the owner’s
manual of your component to be connected to this unit.
The connection methods or the names of the terminals may differ depending on the component. Refer to the owner’s
manual of your component as well.
When your amplifier has a one-channel subwoofer terminal
Connect the subwoofer (or low pass etc.) terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit
using a commercially available mono pin cable.
When your amplifier has two-channel subwoofer terminals
Using one subwoofer
Connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit and “R” side
subwoofer terminal of your amplifier to the INPUT 3 ( ) terminal of this unit using a commercially available audio pin
cable.
Some amplifiers have line output terminals labeled PRE OUT. When you connect this unit to the PRE OUT terminals
of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier has only one
set of PRE OUT terminals, do not connect this unit to the PRE OUT terminals. Instead, connect this unit to the speaker
terminals of the amplifier (see pages 9 - 10).
When connecting to a monaural line output terminal of the amplifier, connect the INPUT 3 ( /MONO) terminal.
When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT
terminals on the rear panel of this unit. If connected, they will not produce sound.
CONNECTIONS
Notes
Connecting to the amplifier equipped with subwoofer (line out) terminal(s)
1
L
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Amplifier
Mono pin cable (not included)
Subwoofer
L
R
Notes
L
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Audio pin
cable
(not included)
Amplifier
Subwoofer
8 En
CONNECTIONS
Using two subwoofers
Connect the “R” side subwoofer terminal of your amplifier to the INPUT 3 ( ) terminal on this unit using a commercially
available mono pin cable, and connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( /MONO)
terminal of this unit using a commercially available mono pin cable.
Connecting to an amplifier equipped with a high cut function
If your amplifier can cut off high frequencies from the signals for sending to the subwoofer, connect
the amplifier to the INPUT 2 (LFE) terminal of this unit. This brings you higher sound quality
because the signal routing in this unit is shortened by bypassing the built-in HIGH CUT (high cut)
circuit.
R
L
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
INPUT
3
INPUT
2
INPUT 1
Mono pin cable
(not included)
Amplifier
Subwoofer
Subwoofer
L
L
R
R
R
R
MONO
INPUT
3
INPUT
2
9 En
CONNECTIONS
Connect an amplifier (and front speakers) to this unit using commercially available speaker cables. Refer to the following
instructions to make connections.
Connecting to the speaker cable
1 Remove approximately 10 mm (3/8”) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
3 Turn the knob counterclockwise to loosen.
4 Insert the bare wire into the hole in the side
of each terminal.
5 Turn the knob clockwise to tighten.
6 Test the firmness of the connection by
pulling gently on the cable at the terminal.
Do not let the bare speaker wires touch each other,
because this could damage this unit or the amplifier,
or both of them.
For connection, keep the speaker cables as short as
possible. Do not bundle or roll up the excess part of the
cables. If the connections are faulty, no sound will be
heard from this unit or the speakers, or both of them.
Make sure that the + and – polarity markings of the
speaker terminals are observed and set correctly. If these
cables are reversed, the sound will be unnatural and lack
bass.
Do not insert the insulation into the hole. The sound may
not be produced.
Banana plug connection
1 Tighten the knob.
2 Insert the banana plug connecter into the
end of the corresponding terminal.
Connecting to an amplifier not equipped with a subwoofer (line out) terminal
2
Notes
12
5
3
4
10 mm
(3/8”)
1
2
10 En
CONNECTIONS
When your amplifier has one set of front speaker terminals
Connect the speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect the OUTPUT terminals
of this unit to the front speakers using a commercially available speaker cable.
y
Connecting front speakers via this unit does not affect the sound quality.
Using one subwoofer
Using two subwoofers
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Front speaker (R) Front speaker (L)
Speaker terminals
Amplifier
Subwoofer
OUTPUT
TO SPEAKERS
FROM
AMPLIFIER
INPUT 3
INPUT 2
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
INPUT
3
INPUT
2
INPUT 1
Front speaker (R) Front speaker (L)
Speaker terminals
Subwoofer (R)
Amplifier
Subwoofer (L)
11 En
CONNECTIONS
When your amplifier has two sets of front speaker terminals and both terminals can output
sound signals simultaneously
Connect one set of front speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect another
set of front speaker terminals of the amplifier to the front speakers using commercially available speaker cables.
Set the amplifier so that both sets of front speaker terminals output sound signals simultaneously.
When your amplifier cannot output sound signals simultaneously even if you connect in this way, follow “When your
amplifier has one set of front speaker terminals” on page 10.
Using one subwoofer
Using two subwoofers
Note
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
Front speaker (R)
Front speaker (L)
Speaker
terminals
Amplifier
Subwoofer
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
INPUT 1
INPUT
3
INPUT
2
INPUT 1
Front speaker (R)
Speaker
terminals
Front speaker (L)
Subwoofer (R) Subwoofer (L)
Amplifier
12 En
CONNECTIONS
If this unit or the amplifier makes a hamming noise when
connecting to the speaker terminals of your amplifier,
connect both of the GND (ground) terminals on your
amplifier and this unit using commercially available
grounding wire as shown in fig. .
When your amplifier has no GND (ground) terminal,
connect to the screw that fastens the top cover of your
amplifier as shown in fig. .
When connecting the GND (ground) terminal, make sure
the power cables of the amplifier and this unit are not
plugged into the AC outlet.
Plug the supplied power cable into the AC IN of this unit
after all other connections are complete, and then plug the
power cable to an AC outlet.
Do not use other power cables. Use the provided cable.
Use of other power cables may result in fire hazard or
electrical shock.
Do not plug the power cable into the AC outlet of your
amplifier. Doing so may create distorted sounds or turn
off the power of your amplifier.
Connecting to the ground terminal
Note
A
B
OUTPUT
TO SPEAKERS
FROM AMPLIFIER
INPUT 1
L
L
L
R
R
R
LR
MONO
INPUT
3
INPUT
2
A B
Connecting the power cable
Notes
POWER
ON
OFF
To the AC
outlet
13 En
Before using this unit, adjust the volume balance of this unit to obtain the optimum volume and tone balance between the
front speakers and this unit by following the procedures below.
1 Set POWER switch on the rear panel of this
unit to the ON position, and then press
POWER to turn on this unit.
The STANDBY/ON indicator lights up green.
2 Press VOLUME to set the volume level of
this unit to the minimum (0).
3 Turn on the power of all other components.
4 Play back a source containing low-
frequency components and adjust the
volume level of your amplifier to the desired
listening level.
Set the tone control on your amplifier to the center
position.
5 Press HIGH CUT / to adjust to the
position where the desired response can be
obtained.
Normally, set the position to a level slightly higher
than the minimum frequency of the front speaker.
* To find out the minimum frequency of the front
speaker, refer to the owner’s manual of the front
speaker.
6 Press VOLUME to increase the volume
gradually to adjust the volume balance
between the front speaker and this unit.
Normally, set the volume to a level where you can
obtain a little more bass effect than when this unit is not
used.
y
If you cannot obtain the desired response, repeat steps
5 and 6.
7 Press PHASE to select the regular or
reverse mode.
Normally, set it to the reverse mode. If you cannot
obtain the desired response, set it to the regular mode.
8 Press B.A.S.S. to select a mode that is
suitable for the source.
1: WIDE
When a movie source is played, the low- frequency
effects are enhanced so that you can enjoy more
powerful sound.
2: NORMAL
When a music or movie etc. source is played, you can
enjoy natural bass sounds.
3: NARROW
When an ordinary music source is played, the
excessive low-frequency signals are cut off to make the
sound clearer.
USING THIS UNIT
Adjusting the sound balance
POWER
ON
OFF
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
1
2,6
1
Remote control Rear panel
SUB
W
STANDBY
/ON
14 En
USING THIS UNIT
You can store up to 3 sets of your favorite settings (volume,
high-cut, phase and B.A.S.S. setting) in this unit.
Storing the setting
In the following procedure, PRESET 1 is used as an
example.
1 Adjust the sound balance between the
volume, high cut, phase and
B.A.S.S. (see
page 13).
2 Press MEMORY.
The PRESET indicators on the front panel flash.
3 Press PRESET 1.
The PRESET 1 indicator lights up. The current setting
is stored as PRESET 1.
y
In step 3, pressing a stored number overwrites the old
setting.
While the VOLUME control or the H-CUT control is
rotating by pressing a PRESET, pressing another
PRESET is ineffective.
Recalling a setting
Press PRESET you want to recall (1, 2 or 3).
Memory back-up
Even if you turn off this unit by using the POWER switch
on the rear panel, this unit recalls the last setting when the
power is turned back on (Last memory function).
If the power is cut for more than one week, the setting is
cleared.
If you set the sleep timer, this unit automatically turns to
the standby mode after 120 minutes.
Press SLEEP.
The color of the STANDBY/ON indicator changes to
orange.
Pressing SLEEP again cancels the sleep timer.
Storing the sound balance settings
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
H-CUT
SUBWOOFER SYSTEM Soavo-900SW
STANDBY
/ON
STANDBY
/ON
PHASE
123123
B.A.S.S.
PRESET
1
00H
z
40Hz
VOLUM E
10
0
1
1
1
2
1
1
3
Remote control
Front panel
STANDBY/ON indicator
900SW
3 123
PRESET
Note
Setting the sleep timer
POWER
STANDBY
SLEEP
PHASE
MEMORY
PRESET
HIGH CUT
VOLUME
213
B.A.S.S.
SLEEP
SUB
W
STANDBY
/ON
15 En
USING THIS UNIT
* This function is available only for Yamaha amplifiers
that meet the following conditions:
– The amplifier was released in 2005 or later.
– The remote control of the amplifier has two different
buttons for STANDBY and ON.
When the AMP ID library code of the remote control has
been changed, this function may not work.
Setting
1 Set POWER switch on the rear panel to the
OFF position.
2 Set POWER switch to the ON position while
pressing and holding
STANDBY/ON switch
on the front panel.
Continue holding down
STANDBY/ON
switch for 3 seconds or longer.
After the STANDBY/ON indicator flashes 4 times, the
setting is completed.
Canceling
1 Set POWER switch on the rear panel to the
OFF position.
2 Set POWER switch to the ON position while
pressing and holding
STANDBY/ON switch
on the front panel.
Continue holding down
STANDBY/ON
switch for 3 seconds or longer.
After the STANDBY/ON indicator flashes 2 times, the
setting is completed.
Place this unit within the operating range of the remote
control of the amplifier. If you place this unit far away from
the amplifier, you may not be able to operate this unit with
the remote control.
Operating the power of this unit using
the remote control of your amplifier
Note
H-CUT
SUBWOOFER SYSTEM Soavo-900SW
STANDBY
/ON
STANDBY
/ON
PHASE
123123
B.A.S.S.
PRESET
10
0H
z
4
0
H
z
VOLUM E
10
0
POWER
ON
OFF
POWER switch
STANDBY/ON switch
Rear panel
Front panel
SUB
W
STANDBY
/ON
Note
SUB
W
STANDBY
/ON
16 En
USING THIS UNIT
Frequency response of this unit
The figures below show the optimum adjustment of each control and the frequency response when this subwoofer is
combined with a typical front speaker system.
EX.1 When combined with a 10 cm or 13 cm (3-15/16” or 5-2/16”) acoustic suspension, 2 way system
front speakers
If you are using Soavo-1 speakers as front speakers, use the following example as a reference when adjusting settings.
EX.2 When combined with a 20 cm or 25 cm (7-14/16” or 9-13/16”) acoustic suspension, 2 way system
front speakers
* These diagrams do not depict actual frequency response characteristics accurately.
Frequency response
reverse mode
(Green)
reverse mode
(Green)
20 50 100 200 500Hz
40
50
60
70
80
90
dB
H-CUT 140 Hz
Frequency response graph*
H-CUT
140Hz
40Hz
VOLUME
10
0
(H-CUT) (VOLUME)
O
OFER SYSTEM
S
PHASE
1
(PHASE)
20 50 100 200 500Hz
40
50
60
70
80
90
dB
Soavo-900SW (H-CUT 60 - 70 Hz)
Front
speaker
Frequency response graph*
H-CUT
140Hz
40Hz
VOLUME
10
0
(H-CUT) (VOLUME)
O
OFER SYSTEM
S
PHASE
1
(PHASE)
20 50 100 200 500Hz
40
50
60
70
80
90
dB
Soavo-900SW (H-CUT 50 - 60Hz)
Front
speaker
Frequency response graph*
1 / 1

Yamaha 900SW Manual de utilizare

Categorie
Amplificatoare audio
Tip
Manual de utilizare
Acest manual este potrivit și pentru