Silvercrest SDM 1500 C2 Operating Instructions Manual

Tip
Operating Instructions Manual

Acest manual este potrivit și pentru

IAN 280641
STEAM MOP SDM 1500 C2
STEAM MOP
Operating instructions
УРЕД ЗА ПОЧИСТВАНЕ С ПАРА
Ръководство за експлоатация
MOP CU ABURI
Instrucţiuni de utilizare
ΣΦΟΥΓΓΑΡΙΣΤΡΑ ΑΤΜΟΥ
Οδηүίες χρήσης
DAMPFMOPP
Bedienungsanleitung
GB / CY Operating instructions Page 1
RO Instrucţiuni de utilizare Pagina 19
BG Ръководство за експлоатация Cтраница 37
GR / CY Οδηүίες χρήσης Σελίδα 55
DE / AT / CH Bedienungsanleitung Seite 73
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.
Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции
на уреда.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
C
A
B
GB
CY
 1
SDM 1500 C2
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Information concerning these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operating components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Unpacking and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package contents and transport inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disposal of packaging materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Assembling the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Handling and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Filling with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
After use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Maintenance/changing the fi lter . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Kompernass Handels GmbH warranty . . . . . . . . . . . . . . . . . . . . . . .15
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Ordering spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2
GB
CY
SDM 1500 C2
Introduction
Information concerning these operating instructions
Congratulations on the purchase of your new appliance.
You have selected a high-quality product. The operating instructions are part of
this product. They contain important information on safety, usage and disposal.
Before using the product, familiarise yourself with all operating and safety instructions.
Use the product only as described and for the specifi ed areas of application.
Please also pass on these operating instructions to any future owner.
Copyright
This documentation is protected by copyright.
Any copying or reproduction, including in the form of extracts, or any reproduction
of images (even in a modifi ed state), is permitted only with the written authorisation
of the manufacturer.
Intended use
This appliance is intended exclusively for cleaning indoor fl oors. The appliance is
not intended for any other purpose, nor for use beyond the scope described. The
appliance is not intended for use in commercial or industrial environments.
The manufacturer accepts no responsibility for damage caused by failure to observe
these instructions, improper use or repairs, unauthorised modifi cations or the use
of unapproved replacement parts. The operator bears sole liability.
GB
CY
 3
SDM 1500 C2
Safety instructions
RISK OF ELECTRIC SHOCK!
Connect the appliance only to mains power sockets supplying
a mains power voltage of 220 - 240 V
~
, 50/60 Hz.
In the event of operating malfunctions, and before cleaning
the appliance, disconnect the plug from the mains power
socket.
To disconnect the power cable, always pull the plug from the
socket, do not pull the power cable itself.
Do not kink or crush the power cable, and route the cable
so that it cannot be stepped on or tripped over.
To avoid risks, arrange for defective plugs and/or power
cables to be replaced at once by qualifi ed technicians or
our Customer Service Department.
Make sure that the power cable does not become wet or
damp during use. Route the cable in such a way that it
cannot be crushed or damaged.
To prevent risks, stop using the appliance immediately if it
is damaged.
Disconnect the appliance from the mains power socket before
lling it with water, changing accessories or cleaning it.
Use the appliance only in dry indoor areas, not
outdoors.
Never submerse the appliance in water or other liquids!
Never aim the steam jet directly at electrical appliances or
equipment which contains electrical components, such as
the interior of ovens.
4
GB
CY
SDM 1500 C2
RISK OF ELECTRIC SHOCK!
Operate the appliance only with dry hands and never without
shoes (i.e. not barefoot). This will help reduce the eff ect of
an electric shock in the event of a malfunction.
Never aim the appliance at moisture-sensitive objects.
This appliance may be used by persons with limited physical,
sensory or mental capabilities or lack of experience and
knowledge, provided that they are under supervision or have
been told how to use the appliance safely and are aware of
the potential risks. Children must not use the appliance as a
plaything. Cleaning and user maintenance tasks may not be
carried out by children unless they are supervised.
WARNING! RISK OF INJURY!
Some parts of the appliance may become hot during use!
There is a risk of scalding!
Allow the accessories used to cool down before dismantling
them.
Use only the original accessory parts for this appliance.
Other accessories may not meet the safety requirements.
The appliance may not be used if it has been dropped, if there
are any obvious signs of physical damage or if it is leaking.
The appliance must be kept out of the reach of children if it
is switched on or is cooling down.
Never direct the steam at people or animals. Hot steam can
cause serious injuries!
Always pull the plug out of the power socket during each
break in use, as well as after use and before any cleaning.
GB
CY
 5
SDM 1500 C2
RISK OF BURNS!
Caution! Hot surface!
This symbol warns you about escaping steam.
Please follow the safety instructions!
CAUTION! MATERIAL DAMAGE!
Use the appliance only on fl oors made of marble, stone, tile,
parquet fl ooring or hardwood that have been treated and
are impervious to water.
Never use the appliance ...
... on untreated or permeable fl oors,
... on glass surfaces,
... on soft plastic surfaces,
... on fl oors that have been treated with wax,
... on carpets with wool content.
Always comply with the cleaning instructions of the carpet
manufacturer. Before cleaning, check also whether the car-
pet is suitable for steam cleaning. Use the appliance only
on parquet fl oors if they have been hard-sealed.
Do not leave the appliance standing on wooden fl oors for
any length of time while it is switched on. This might cause
the wood to swell.
Do not operate the appliance with an empty water tank.
Otherwise, the pump could run dry and overheat.
Do not use an external timer switch or a separate remote
control system to operate the appliance.
Never leave the appliance unattended during operation.
Do not use the appliance outdoors.
6
GB
CY
SDM 1500 C2
CAUTION! MATERIAL DAMAGE!
Ensure that the appliance, the power cable and the plug do
not come into contact with heat sources such as hotplates or
naked fl ames.
Operating components
Figure A:
1 “Handle” release button
2 Carrying handle
3 Main unit
4 Connection nozzle
5 Steam foot
6 Pad
7 Filter
8 Water tank
9 Water tank” release button
0 POWER control lamp
q Red control lamp “high steam level”
w Green control lamp “low steam level”
e MODE button
r “Steam” button
Figure B:
t Notch
z Upper cable hook
u On/off switch
i Lower cable hook
Figure C:
o Replacement pad
p Carpet ring
a Carpet ring release aid
GB
CY
 7
SDM 1500 C2
Unpacking and installation
Safety instructions
WARNING
During the fi rst use of the appliance there is a risk
of injury and/or damage to property!
To avoid risks, observe the following safety instructions:
Do not allow children to play with packaging materials.
There is a risk of suff ocation.
Package contents and transport inspection
The appliance is supplied with the following components as standard (see fold-
out page):
Main unit
Steam foot
Carpet cleaning ring
2 pads
Operating instructions
NOTE
Check the package for completeness and for signs of visible damage.
If the delivery is incomplete or damage has occurred as a result of defec-
tive packaging or during transport, contact the service hotline (see section
Service).
Unpacking
Remove all parts of the appliance and the operating instructions from the box.
Remove all packaging materials and any fi lms and labels.
8
GB
CY
SDM 1500 C2
Disposal of packaging materials
The packaging protects the appliance from damage during transport. The packaging
materials have been selected for their environmental friendliness and ease of
disposal, and are therefore recyclable.
Returning the packaging into the material cycle conserves raw materials and
reduces the amount of waste generated. Dispose of packaging materials that
are no longer needed in accordance with applicable local regulations.
NOTE
If possible, keep the appliance's original packaging during the warranty
period so that the appliance can be packed properly for return shipment
in the event of a warranty claim.
Assembling the appliance
Push the main unit 3 onto the connection nozzle 4 on the steam foot 5 and
press the main unit 3 down until the round catch clicks into place.
Attach a pad 6 from below onto the steam foot 5.
NOTE
If you intend to clean carpeting with the steam mop, fi t the steam foot 5
onto the carpet ring p. Ensure that the carpet ring unlocking aid a is in
line with the connection nozzle 4. Push the steam foot 5 onto the carpet
ring p so that it clicks audibly into place. This will allow the pad 6 to
glide over the carpet.
To remove the carpet ring p, press your foot onto the carpet ring release
aid a and pull the steam foot 5 carefully off the carpet ring p.
Handling and operation
This section provides you with important information on handling and using the
appliance.
Filling with water
CAUTION – PROPERTY DAMAGE!
Never operate the appliance without water in the water tank 8!
The pump could overheat and be damaged!
1) Push the “Water tank” release button 9 downwards and simultaneously
pull the water tank 8 towards the rear and off the appliance with a tilt
movement.
2) Turn the water tank 8 and unscrew the cap.
3) Fill the water tank 8 with tap water up to the MAX mark.
GB
CY
 9
SDM 1500 C2
NOTE
If the mains water in your location is rated as hard, it is recommended that
you mix the mains water with some distilled water. Otherwise, the jets for
the steam blast function could calcify (become blocked) prematurely.
To extend the optimal steam blast function, mix mains water with
distilled water according to the table:
Water hardness Ratio of distilled
water to
tap water
very soft/soft 0
medium 1:1
hard 2:1
very hard 3:1
The water hardness level can be queried at your local water works.
4) Attach and hand-tighten the clamp.
5) Turn the water tank 8 around again and place it back onto the main unit 3:
First fi t the lower part into the main unit 3 and then fl ip the top part into the
device. Push it fi rmly into place so that the water tank 8 audibly clicks into
place and sits fi rmly on the main unit 3.
Operation
CAUTION – PROPERTY DAMAGE!
If you are not sure whether the fl oor is suitable for cleaning, please carry
out a tolerance test using a concealed part of the fl oor.
Always comply with the cleaning instructions of the carpet manufacturer.
Before cleaning, check also whether the carpet is suitable for steam clean-
ing.
Never use the appliance without a pad 6 on the steam foot 5.
Otherwise the fl oor could get scratched!
Never operate the appliance without water in the water tank 8!
The pump could overheat and be damaged!
NOTE
Before you clean the fl oor with the steam mop, we recommend that you
vacuum the fl oor to remove any loose particles of dirt.
Once the appliance is assembled and fi lled with water:
1) Press and hold in the “Handle” release button 1 and fl ip the handle up-
wards so that it clicks into place.
10
GB
CY
SDM 1500 C2
2) If not already done: Completely unwind the power cable from the cable
hooks z/i. To facilitate the unwinding of the cable, you can fl ip down the
upper cable hook z by pulling it out a little and turning it at the same time.
3) Run the cable through the notch t on the rear of the handle so that the
cable does not hang down into the working area.
4) Insert the plug into the mains power socket.
5) Set the on/off switch u to “I”. The on/off switch u lights up, the red
POWER control lamp 0 ashes.
6) Use the MODE button e to select the desired level of steam generation:
Press 1 x: low steam level, green control lamp w lights up.
Press 2 x: high steam level, red control lamp q lights up.
Press 3 x: no steam, standby, POWER control lamp 0 lights up.
NOTE
We recommend the high steam level especially for moisture- and heat-
resistant fl oor coverings, such as tiles.
We recommend the low steam level especially for moisture- and heat-
sensitive fl oor coverings, such as parquet fl ooring.
7) Wait around 30 seconds while the appliance heats up.
8) Press the “Steam” button r. The appliance starts generating steam and,
after a short time, steam is emitted through the pad 6.
9) Wipe over the desired area.
If the water tank 8 becomes empty during use:
NOTE
Once the water tank 8 has been pumped empty, the pump will continue
running a little while until the empty water tank 8 is indicated by the simul-
taneous fl ashing of the red control lamp “high steam level” q, the green
control lamp “low steam level” w and POWER control lamp 0.
Press the “Steam” button r again to stop steam production.
Set the on/off switch u to “O”.
Remove the water tank 8, fi ll it and replace the water tank 8 as
described in the section “Filling with water”.
Set the on/off switch u to “I”.
Select the desired steam level as described above and press the
“Steam” button r.
GB
CY
 11
SDM 1500 C2
10) When you are fi nished treating all of the surfaces, press the “Steam”
button r to stop steam production.
11) Set the on/off switch u to “O”. The POWER control lamp 0 goes out.
12) Remove the power plug from the mains power socket.
NOTE
If you see streaks on the fl oor after cleaning with the appliance, this may
be due to the previously used cleaning fl uids. Simply clean the fl oor again
using the steam mop. The smears should now be gone.
After use
1) Allow the appliance to cool down.
2) Remove the pad 6.
3) Remove the water tank 8 from the appliance and empty it.
4) Pull the upper cable hook z out a little and turn it back upwards.
Wind the cable back around the two cable hooks z/i.
Fix the end of the power cable using the cable clip located on the cable.
Cleaning and care
RISK OF ELECTRIC SHOCK!
Always remove the mains power plug before cleaning the appliance!
WARNING – RISK OF INJURY!
Allow the appliance to cool down before cleaning it. Risk of burns!
CAUTION – PROPERTY DAMAGE
When cleaning the surfaces use neither abrasive or chemical cleaners,
nor sharp or scratchy objects.
Empty the water tank 8 after every use.
After each use, remove the pad 6 from the steam foot 5 and wash it out.
12
GB
CY
SDM 1500 C2
Note the following washing instructions when you wash the pad 6 in the
washing machine:
Wash at max. 60°C
Do not tumble dry
Do not iron
If necessary, wipe the appliance with a damp cloth. For stubborn soiling use
a mild detergent on the cloth.
Maintenance/changing the fi lter
After 4–6 months or approximately 100 cleaning cycles (one cycle corresponds
to one water tank fi lling), you will need to change the fi lter 7. Please contact
our Service Department for replacement fi lters.
RISK OF ELECTRIC SHOCK!
Before changing the fi lter 7, always pull out the mains plug!
1) To remove the fi lter 7, fi rst remove the water tank 8 from the appliance.
2) Pull the fi lter 7 upwards out of the appliance.
3) Insert the new fi lter 7.
4) Replace the water tank 8.
GB
CY
 13
SDM 1500 C2
Troubleshooting
Programme Possible causes Possible solutions
The appliance is
not working.
The plug is not connected.
Connect the appliance to a
mains power socket.
The appliance
produces no steam.
The "Steam" button r has
not been pressed.
Press the "Steam" button r.
There is no water in the
water tank 8.
Fill the water tank 8 with
tap water.
The fi lter 7 is blocked. Change the fi lter 7.
No steam setting has
been selected.
Use the MODE button e to
select the desired level of steam.
The pump makes
unusually loud
noises.
There is no water in the
water tank 8.
Fill the water tank 8 with
tap water.
A whitish edge
forms on the fl oor
when the appliance
stops briefl y during
operation.
Lime has collected.
Wipe the limescale away with a
damp cloth. If necessary, add a
little descaler onto the cloth.
14
GB
CY
SDM 1500 C2
Storage
Fold the handle by pressing the “Handle” release button 1.
Pull the upper cable hook z out a little and turn it back upwards.
Wind the cable back around the two cable hooks z/i.
Carry the appliance using the carrying handle 2.
Store the appliance in a dry and dust-free location.
Disposal
Do not dispose of the appliance in your normal domestic waste.
This product is subject to the provisions of European Directive
2012/19/EU-WEEE (Waste Electrical and Electronic Equipment).
Dispose of the appliance via an approved waste disposal company or your
municipal waste disposal facility. Please comply with all applicable regulations.
Please contact your waste disposal facility if you are in any doubt.
Appendix
Technical data
Voltage supply 220 - 240 V
~
(AC) | 50 / 60 Hz
Power consumption 1370 - 1630 W
Protection rating
IPX4
Protected against water splashes
from any direction.
Information on the pads 6/o
Material composition 100% polyester
Wash at max. 60°C
Do not tumble dry
Do not iron
GB
CY
 15
SDM 1500 C2
Kompernass Handels GmbH warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this product
has any faults, you, the buyer, have certain statutory rights. Your statutory rights
are not restricted in any way by the warranty described below.
Warranty conditions
The validity period of the warranty starts from the date of purchase. Please keep
your original receipt in a safe place. This document will be required as proof of
purchase.
If any material or production fault occurs within three years of the date of purchase
of the product, we will either repair or replace the product for you at our discretion.
This warranty service is dependent on you presenting the defective appliance
and the proof of purchase (receipt) and a short written description of the fault
and its time of occurrence.
If the defect is covered by the warranty, your product will either be repaired or
replaced by us. The repair or replacement of a product does not signify the begin-
ning of a new warranty period.
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs eff ected under the warranty.
This also applies to replaced and repaired components. Any damage and defects
present at the time of purchase must be reported immediately after unpacking.
Repairs carried out after expiry of the warranty period shall be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance with strict quality guidelines
and inspected meticulously prior to delivery.
The warranty covers material faults or production faults. The warranty does not
extend to product parts subject to normal wear and tear or fragile parts such as
switches, batteries, baking moulds or parts made of glass.
The warranty does not apply if the product has been damaged, improperly used
or improperly maintained. The directions in the operating instructions for the product
regarding proper use of the product are to be strictly followed. Uses and actions
that are discouraged in the operating instructions or which are warned against
must be avoided.
This product is intended solely for private use and not for commercial purposes.
The warranty shall be deemed void in cases of misuse or improper handling, use
of force and modifi cations / repairs which have not been carried out by one of
our authorised Service centres.
16
GB
CY
SDM 1500 C2
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
Please have the till receipt and the item number (e.g. IAN 12345) available
as proof of purchase.
You will fi nd the item number on the type plate, an engraving on the front
page of the instructions (bottom left), or as a sticker on the rear or bottom of
the appliance.
If functional or other defects occur, please contact the service department
listed either by telephone or by e-mail.
You can return a defective product to us free of charge to the service address
that will be provided to you. Ensure that you enclose the proof of purchase
(till receipt) and information about what the defect is and when it occurred.
You can download these instructions along with many other manuals,
product videos and software on www.lidl-service.com.
Service
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
CY
Service Cyprus
Tel.: 8009 4409
IAN 280641
Importer
Please note that the following address is not the service address. Please use the
service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
GB
CY
 17
SDM 1500 C2
Ordering spare parts
You can order the following replacement parts for product SDM 1500 C2:
2 x Replacement pad 1 x Filter
Order the replacement parts via the Service Hotline (see section „Service“) or
simply visit our website at www.kompernass.com.
NOTE
Have the IAN number of the appliance ready (can be found on the cover
of these operating instructions) when you place your order.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

Silvercrest SDM 1500 C2 Operating Instructions Manual

Tip
Operating Instructions Manual
Acest manual este potrivit și pentru

în alte limbi