Yamaha SLG130NW Manualul proprietarului

Marca
Yamaha
Categorie
accesorii pentru chitară
Model
SLG130NW
Tip
Manualul proprietarului
1
Thank you for purchasing the Yamaha Silent Guitar. In order to obtain the
maximum performance and enjoyment from your Silent Guitar, we urge you
to read this Owner’s Manual thoroughly before using the instrument. Please
keep this Owner’s Manual in a safe place for later reference.
Contents
Precautions .................................................................... 3
Main Body/Accessories ................................................ 4
Nomenclature ................................................................ 5
Attaching the Frame ...................................................... 7
About the Strap Pin ...................................................................... 7
Changing Strings .......................................................... 8
Power Supply ................................................................. 9
Supplying AC Power ..................................................................... 9
Installing the Battery ..................................................................... 9
Connecting External Devices ..................................... 10
AUX IN jack ................................................................................ 11
Output Jacks (LINE OUT Jack/Headphone Jack) ...................... 11
Using the Controls ...................................................... 12
Using the LINE OUT jack ........................................................... 12
Using the stereo earphones ....................................................... 12
Using the Soft Case .................................................... 13
Specifications .............................................................. 14
SLG110N/130NW
Owner’s Manual
English
02_slg110n_en.indd 1 10/10/20 20:53
2
SPECIAL MESSAGE SECTION
92-BP
This product utilizes batteries or an external power supply (adaptor). DO NOT
connect this product to any power supply or adaptor other than one described
in the manual, on the name plate, or specifically recommended by Yamaha.
This product should be used only with the components supplied or; a cart,
rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please
observe all safety markings and instructions that accompany the accessory
product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained
in this manual is believed to be correct at the time of printing. However, Yamaha
reserves the right to change or modify any of the specifications without notice or
obligation to update existing units.
Do not attempt to service this product beyond that described in the user-
maintenance instructions. All other servicing should be referred to qualified
service personnel.
This product, either alone or in combination with an amplifier and headphones
or speaker/s, may be capable of producing sound levels that could cause
permanent hearing loss. DO NOT operate for long periods of time at a high
volume level or at a level that is uncomfortable. If you experience any hearing
loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before dam-
age occurs.
NOTICE:
Service charges incurred due to a lack of knowledge relating to
how a function or effect works (when the unit is operating as designed) are
not covered by the manufacturer’s warranty, and are therefore the owner’s re-
sponsibility. Please study this manual carefully and consult your dealer before
requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that
are both user safe and environmentally friendly. We sincerely believe that our
products and the production methods used to produce them meet these goals.
In keeping with both the letter and the spirit of the law, we want you to be
aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable bat-
tery which (if applicable) is soldered in place. The average life span of this type
of battery is approximately five years. When replacement becomes necessary,
contact a qualified service representative to perform the replacement.
This product may also use “household” type batteries. Some of these may be
rechargeable. Make sure that the battery being charged is a rechargeable type
and that the charger is intended for the battery being charged.
When installing batteries, do not mix old batteries with new, or with batteries of
a different type. Batteries MUST be installed correctly. Mismatches or incorrect
installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble or incinerate any battery. Keep
all batteries away from children. Dispose of used batteries promptly and as
regulated by the laws in your area. Note: Check with any retailer of household
type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or
for some reason its useful life is considered to be at an end, please observe all
local, state, and federal regulations that relate to the disposal of products that
contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please
contact Yamaha directly.
NAMEPLATE LOCATION:
The nameplate is located on the back of
the product. The model number, serial number, power requirements, etc., are
located on this plate. You should record the model number, serial number, and
the date of purchase in the spaces provided below and retain this manual as a
permanent record of your purchase.
Model Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
FCC INFORMATION (U.S.A.)
pliance with FCC regulations does not guarantee that interference will
not occur in all installations. If this product is found to be the source of
interference, which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna.
If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-
axial type cable.
If these corrective measures do not produce satisfactory results, please
contact the local retailer authorized to distribute this type of product. If
you cannot locate the appropriate retailer, please contact Yamaha Corpo-
ration of America, Electronic Service Division, 6600 Orangethorpe Ave,
Buena Park, CA 90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modifications not expressly
approved by Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT
:
When connecting this product to accessories and/or
another product use only high-quality shielded cables. Cable/s supplied
with this product MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC authorization to use
this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital de-
vices. Compliance with these requirements provides a reasonable level
of assurance that your use of this product in a residential environment
will not result in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not installed and
used according to the instructions found in the user’s manual, may cause
interference harmful to the operation of other electronic devices. Com-
CANADA*
THIS DIGITAL APPARATUS DOES NOT EXCEED THECLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET
OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX AP-
PAREILS NUMERIQUES DE LACLASSE B” PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIO ELECTRI QUE EDICTE PAR
LE MINISTERE DES COMMUNICATIONS DU CANADA.
This applies only to products distributed by Yamaha Canada Music Ltd.
Ceci ne s’applique quaux produits distribs par Yamaha Canada Musique Ltée.
02_slg110n_en.indd 2 10/10/20 20:53
3
Your Silent Guitar will give you years of reliable service if you follow the simple rules given below:
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points, in accordance with your national legislation and the Directives
2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact
your local municipality, your waste disposal service or the point of sale where you purchased the
items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
Location
Do not expose it to the following conditions to avoid
deformation, discoloration, or more serious damage.
Direct sunlight (e.g. near a window).
High temperatures (e.g. near a heat source, outside,
or in a car during the daytime).
Excessive humidity.
Excessive dust.
Strong vibrations.
Power Supply
Turn the power switch OFF when not in use.
If you use an AC power adaptor, unplug the adaptor
from the AC outlet if not to be used for an extended
period of time.
If you use an AC power adaptor, make sure that the
AC outlet you are using is easily accessible.
Do not install this equipment in a confined space
such a book case or similar unit.
If some trouble or malfunction occurs, immediately
turn off the power switch and unplug the adaptor
from the outlet.
This product is not disconnected from the AC power
source as long as the adaptor is connected to the
outlet, even if the power switch is turned off.
Unplug the AC power adaptor during electric storms.
Avoid plugging the AC power adaptor into the same
AC outlet as appliances with high power consump-
tion, such as electric heaters or ovens. Also avoid
using multi-plug adaptors since these can result in
reduced sound quality and possible damage.
If the instrument is not going to be used for an
extended period of time, or when battery power
is depleted, we recommend that the batteries be
removed in order to avoid power consumption or
leakage.
Never dismantle the batteries and never dispose
batteries in fire.
Never touch any fluid that may leak from the battery.
If the fluid should come in contact with the eyes,
mouth, or skin, wash immediately with water and
consult a doctor.
Turn Power OFF When Making Connections
To avoid damage to the Silent Guitar and other
devices to which it is connected (a sound system,
for example), turn the power switches of all related
devices OFF prior to connecting or disconnecting
audio cables.
Handling and Transport
Never apply excessive force to the controls, connec-
tors or other parts.
Always unplug cables by gripping the plug firmly,
not by pulling on the cable.
Disconnect all cables before moving the unit.
Physical shocks caused by dropping, bumping,
or placing heavy objects on the unit can result in
scratches and more serious damage.
Cleaning
Clean the guitar body with a dry soft cloth.
A slightly damp cloth may be used to remove stub-
born grime and dirt.
Never use cleaners such as alcohol or thinner.
Electrical Interference
This unit contains electric circuitry and may cause
interference if placed too close to radio or television
receivers. If this occurs, move it further away from
the affected equipment.
YAMAHA is not responsible for damage
caused by improper handling or operation.
02_slg110n_en.indd 3 10/10/20 20:53
4
Main Body/Accessories
After opening the packaging, please check that all the parts listed below are in-
cluded.
• Main body
• Left frame
• AC adaptor
PA-D012(A), PA-130(A), PA-D09
*
Product numbers may vary according to
the region. Additionally, instruments sold
in some countries may not be supplied
with an AC adaptor.
• Stereo earphones
• Soft case
02_slg110n_en.indd 4 10/10/20 20:53
5
Nomenclature
Front
Rear
Fingerboard
Neck
Saddle
Tuning peg
Nut
Body
Pickup
(underneath
the saddle)
Controls
See page 6.
Frame attachment screw 1
(Doubles as the strap pin)
Left frame
(Removable)
Right frame (Fixed)
Bridge
Horn (Leg support)
Frame attachment screw 2
(Doubles as the strap pin)
Finger rest
OPEN
LINE OUT
AUX IN
AUX VOL
MIN MAX
02_slg110n_en.indd 5 10/10/20 20:53
6
use 6LR61 9V
alkaline battery
Controls
VOLUME control
Battery compartment
EFFECT switch
POWER lamp
AUX IN jack
AUX IN
level control
Cord hook
LINE OUT jack
DC-IN jack
(Power adaptor connector)
BASS control
TREBLE control
PHONES ON/OFF
switch
PHONES jack
Nomenclature
OPEN
LINE OUT
AUX IN
AUX VOL
MIN MAX
OFF ON
PHONES
VOLUME BASS TREBLE
OFF
REV1
REV2
ECHO
CHORUS
EFFECT
02_slg110n_en.indd 6 10/10/20 20:53
7
When shipped from the factory, the left frame is not attached to the Silent Guitar’s
main body.
Before using the instrument, please properly attach the left frame using the proce-
dure described below.
After the frame is attached, make sure attachment screws 1 and 2 are tightened firmly. Using the instru-
ment with the screws loose will result in rattle or other noise during performance.
When transporting the instrument, please carry the instrument by its neck or main body. Holding the
instrument by only its left or right frame will result in damage of the frame or the frame’s fixed parts.
1.
Fully loosen [frame attachment screw 1] located in the
area behind the 12
th
fret, and [frame attachment screw 2]
located at the end of the Silent Guitar’s main body.
2.
Insert the lower rod of the left frame fully into the
bracket hole on the Silent Guitar’s main body.
Next, insert the upper rod fully into the bracket hole.
Make sure that the upper and lower ends of the left
frame are not reversed.
Do not place any excess force on the frame’s rods.
The rods may become damaged.
3.
After confirming that both rods of the left frame are
fully inserted, turn the attachment screws clockwise and
secure the left frame to the Silent Guitar’s main body.
W h e n m o v in g a n y m o v ab l e p a r ts ,
make sure that your fingers or hand do
not become pinched in the parts.
Do not tighten the attachment screws
when the frame is removed. It will re-
sult in the damage of parts, which will
cause problems when re-attaching the
frame.
Attaching the Frame
Attachment of the frame is now complete.
To remove the frame, simply reverse the order of the procedure described above, removing the upper
rod from tha main body before removing the lower rod.
About the Strap Pin
The frame attachment screw can be used as a strap pin for a separately purchased guitar strap.
Make sure that the strap is firmly hooked onto the strap pin so the instrument does not drop during
performance.
Frame attachment screw 1
Frame attachment screw 2
q
Rod
w
Rod
OPEN
LINE OUT
AUX IN
AUX VOL
MIN MAX
q
First, insert the
lower rod into the
main body.
w
Then, insert the
upper rod.
02_slg110n_en.indd 7 10/10/20 20:53
8
Changing Strings
1.
Thread the string through the corresponding string hole on the bridge, then tie the string as shown in
the illustration below.
After tying the knot, pull both ends of the string to make the knot firm on the bridge.
2.
Next, tie the strings to the pegs.
Hold the guitar so the head is facing you and wind the strings onto the pegs as shown in the illustra-
tion below.
3.
After all six strings are strung, tune the guitar properly.
As the strings get old, sound quality will gradually decrease, and it will become
difficult to tune the instrument. Change the strings as soon as you think they are
getting old.
Make sure you purchase a set of nylon guitar strings. The Silent Guitar uses a
string length of 650mm (25-9/16 inch).
The end of the strings are sharp and can cut fingers. Use caution when changing strings.
When changing or adjusting strings, do not put your face close to the instrument. The string may sud-
denly break resulting in eye or other unexpected injuries.
The pickup sensor is set into the bridge underneath the saddle. When changing strings, please change
them one at a time to prevent the saddle or pickup from moving.
If the saddle is removed, make sure that the sensor does not get moved. When attaching the saddle,
make sure that the saddle’s lowest end is positioned under the first string.
Winding the 4
th
, 5
th
and 6
th
strings
B
Make the first wind to the left of the
hole, and the remaining winds to the
right.
Winding the 1
st
, 2
nd
and 3
rd
strings
A
Make the first wind to the right of the
hole, and the remaining winds to the
left.
bridge
neck side
* If the string slips (1
st
, 2
nd
, 3
rd
strings) tie one more knot.
Make sure the last knot is
positioned over the edge of
the bridge.
A
A
A
B
B
B
02_slg110n_en.indd 8 10/10/20 20:53
9
Power Supply
The Silent Guitar operates either on battery power or with an AC adaptor however,
it will consume more power when the reverb function is in use. For that reason, we
recommend that it be powered with the supplied AC power adaptor for normal use.
Always turn the PHONES ON/OFF switch OFF before making AC power
connections or replacing the battery.
When battery power becomes low, the effect does not operate, the lamp will not light, and noise will be
present. Replace the battery with a new alkaline battery as soon as possible.
Always follow the +/– signs when inserting the battery. Improper insertion may result in fire.
If the instrument is not going to be used for an extended period of time, or when battery power is de-
pleted, we recommend that the batteries be removed in order to avoid power consumption or leakage.
Supplying AC Power
1.
Plug the adaptor’s DC output cable into the Silent Guitar’s DC IN jack, making sure the plug is firmly
inserted into the jack.
2.
Plug the AC adaptor into a convenient wall AC power socket.
Battery power is automatically disconnected when the AC adaptor is connected.
When the AC adaptor is used, the batteries may leak. To prevent leakage we recommend that you re-
move the batteries from the instrument. When the AC adapter is used.
When using an AC adaptor, make sure you use only one of the following recommended adaptors (Rec-
ommended Adaptors: PA-D012(A), PA-130(A), PA-D09, PA-3C). The use of any other adaptor may result
in damage to the instrument or cause fire, etc. Please use with caution.
Installing the Battery
1.
Be sure to use a 9-volt alkaline battery 6LR61. (not supplied)
When using a battery, please use an alkaline battery. Use of a manganese battery will result in an
extremely shorter battery life depending upon the type of battery used.
2.
Remove the battery compartment cover, located on
the back side of the Silent Guitar, by sliding the
tab labeled “OPEN” toward the head of the guitar.
3.
Attach the 9-volt battery 6LR61 to the battery
snap, and place it in the battery case.
Take careful note of the polarity markings (+/-) as
shown in the illustration when connecting the bat-
tery. (Reversed polarity may damage the circuit.)
4.
Close the battery compartment cover.
6LR61 9V
Alkaline battery
Battery compart-
ment cover
Battery snap
02_slg110n_en.indd 9 10/10/20 20:53
10
OPEN
LINE OUT
AUX IN
AUX VOL
MIN MAX
LINE OUT
AUX IN
PHONES
DC-IN
LINE OUT
AUX IN
AUX VOL
MIN MAX
Connecting External Devices
Silent Guitar
or
Power adaptor
Electric
outlet
• Using the cord hook
Wrap the power adaptor’s cord around the cord
hook (prevents cord from being unplugged).
Cord hook
From the LINE OUT jack,
etc.
CD player
Portable music player
Cassette player
Electronic metronome
To the LINE IN jack,
etc.
Guitar amplifier,
Powered speaker
Electronic tuner
When connecting the instrument to external audio equipment, check the jack size and make sure to use
a plug size that corresponds to the jack being used, and properly connect the cable to the jack.
P.A. mixer, Recording device
(Monaural output)
6LR61
Alkaline
battery
Stereo earphones
Recorder, Mixer, etc.
(Stereo output)
02_slg110n_en.indd 10 10/10/20 20:53
11
AUX IN jack
The AUX IN jack can be used to connect an external stereo signal source to the Silent Guitar.
Connecting the audio output of a CD player, portable music player, etc., to the instrument allows you
to play along with the external audio source.
The AUX IN jack’s signal level can be controlled with the AUX IN level control.
Output Jacks (LINE OUT Jack/Headphone Jack)
The LINE OUT jack can be connected to an external input jack on a device such as a guitar amplifier,
powered speaker, mixing console, etc., using a separately purchased standard monaural phone cable.
This allows monitoring or recording of the Silent Guitar’s sound via an external device.
Connecting the LINE OUT jack to the INPUT jack on an electronic tuner, allows tuning of the instru-
ment in the same manner as other electronic instruments.
When using the supplied stereo earphones, insert the earphone plug into the headphones jack (PHONES)
and turn the headphone ON/OFF switch to its “ON” position.
The LINE OUT jack is a monaural type jack while the headphones jack is stereo.
Before connecting the Silent Guitar to any external devices, make sure that the power of
all related devices is turned OFF. Set the volume level of any external audio sources to the
minimum level before connecting anything. High volume settings could cause damage to
the equipment and your hearing.
Be careful not to step on the cord. The cord may break, equipment may be damaged, and
this may cause a substantial shock to your ears.
The signal from the Silent Guitar’s output jacks must NEVER be returned to the AUX IN jack,
either directly or through external equipment. Doing so will result in feedback which may
cause damage to the internal electronics.
Connecting External Devices
02_slg110n_en.indd 11 10/10/20 20:53
12
Using the Controls
Using the LINE OUT jack
(Using with a guitar amplifier or powered speaker, etc.)
1.
Use a standard phone plug cable to connect the Silent Guitar’s LINE OUT jack to the input jack on the
guitar amplifier or powered speaker, etc.
When the cable’s plug is inserted into the LINE OUT jack, power will be supplied to the Silent Guitar
and the power lamp will light.
Before making any connections, make sure that the output volume on the guitar amplifier or pow-
ered speaker, etc., is turned down or its power is switched OFF.
When the guitar is not being used, disconnect the cable’s plug to save battery.
2.
Rotate the VOLUME knob while playing, and adjust the volume to a suitable level.
If the sound is distorted when playing vigorously, turn the VOLUME knob slightly to the left.
3.
Rotate the BASS and TREBLE control knobs to adjust the sound quality.
Rotate the BASS knob to the right to increase the low frequencies, and to the left to decrease the low
frequencies.
Rotate the TREBLE knob to the right to increase the high frequencies, and to the left to decrease the
high frequencies.
4.
You can add different effects to the guitar’s tone using the EFFECT function.
OFF .................Disengages the effect function. Only the original non-processed guitar sound is heard.
REV1 ...............Adds reverb similar to what you would normally experience in a room.
REV2 ...............Adds reverb similar to what you would normally experience in a hall.
CHORUS.........The chorus effect makes it sound as if two guitars are being played.
ECHO ..............Adds an echo effect to the guitar’s sound.
Power consumption is slightly lower when the EFFECT switch is set to the “OFF” position compared
to the other EFFECT setting positions.
Noise may be produced when changing the setting with the EFFECT switch.
A time lag may occur when switching to another effect causing a delay until the next effect is produced.
Using the stereo earphones
(or stereo output to an external device)
When using the instrument with the supplied stereo earphones or a separately purchased pair of
headphones, or when you want to send the instrument’s stereo output to an external device, use
the headphones (PHONES) jack for connecting the earphones or external device.
1.
Set the headphones ON/OFF switch, located on the right side of the control panel, to its “ON” position
to supply power to the Silent Guitar. The power lamp will light.
When using the LINE OUT jack, audio output is delivered to the headphones jack regardless of the
headphones ON/OFF switch position.
When the power is
ON, the lamp lights.
Adjusts high
frequencies
Adjusts the
volume
Selects
the effect.
Adjusts low
frequencies
OFF ON
PHONES
VOLUME BASS TREBLE
OFF
REV1
REV2
ECHO
CHORUS
EFFECT
02_slg110n_en.indd 12 10/10/20 20:53
13
When putting the Silent Guitar into the supplied soft case, remove the left frame
from the Silent Guitar, and then place in the individual parts in the case as shown
in the illustration below.
Placing the instrument in the soft case does not guarantee against any dam-
ages to individual parts.
The soft case is designed for storing and transporting the instrument, and protecting it from dust, etc. Do
not position the instrument with its bridge side facing down in the case, and do not cause any damage to
the instrument by placing any objects on top of the case, hitting it, etc.
Power adaptor
Left frame
Using the Soft Case
Silent Guitar
main body
Using the Controls
/
Using the Soft Case
Put the left frame into the case’s
larger pocket.
Put the power adaptor into the
smaller pocket in the case and
secure the cover using the Vel-
cro® tape.
When laying the case down
with the instrument packed in-
side, make sure that the case is
placed with the guitars bridge
side facing up.
2.
Insert the earphone plug into the headphone jack. When connecting the instrument to an external de-
vice, connect the external device to the PHONES jack using a cable with a stereo plug.
3.
The remaining procedures are the same as described above in the “Using the LINE OUT jack” sec-
tion’s steps 2 through 4.
When using a pair of headphones, do not operate at high volume levels for long periods of time. Do-
ing so can lead to irreparable damage to your hearing.
Do not disconnect or connect the plug when the headphones are placed over your ears.
02_slg110n_en.indd 13 10/10/20 20:53
14
Specifications
Neck
Mahogany
Body
Maple
Fingerboard
Rosewood (SLG130NW : Ebony)
Bridge
Rosewood
Frame Unit
Maple (SLG130NW : Rosewood/Maple)
Strings
Nylon Guitar Strings
Sensors
B-BAND
Connectors/Controls
AUX IN
AUX IN Level Control
LINE OUT jack (monaural)
PHONES jack (stereo)
Volume
BASS control
TREBLE control
EFFECT switch (OFF/REV1/REV2/CHORUS/ECHO)
PHONES switch (ON/OFF)
LINE OUT Jack with POWER Switch
(Inserting a plug into the jack switches the power on)
Power Supply
AC Adaptor/battery
(6LR61 or 6F22) x1 dual power source
* Recommended AC Adaptors: PA-D012(A), PA-130(A), PA-
D09, PA-3C
* Recommended Battery: 6LR61 alkaline battery
Battery Life
Continuous Use
Using Alkaline battery : approximately 20 hours
Using Manganese battery : approximately 9 hours
With the effect activated
Using Alkaline battery : approximately 13 hours
Using Manganese battery : approximately 5 hours
String Length
650 mm (25-9/16”)
Dimensions
(with the left frame attached and to the end of the strap pin)
965 (L) x 365 (W) x 80 (H) mm
38” (L) x 14-3/8” (W) x 3-1/8” (H)
Weight
approximately 1.8 kg (3 lbs. 15 oz.)
* Design and specifications are subject to change without notice.
02_slg110n_en.indd 14 10/10/20 20:53
/

Acest manual este, de asemenea, potrivit pentru