Yamaha SLB300 Manualul proprietarului

Tip
Manualul proprietarului
1
SLB300 Owners Manual
SLB300
Owners Manual
Thank you very much for purchasing the Yamaha “SILENT Bass
TM
.
This product is a brand-new type of electric upright bass that achieves natural sound and
resonance by using the SRT POWERED system to reproduce studio-quality sound in
which the body resonance of a double bass was recorded using a high-quality micro-
phone, all the while keeping a semi-solid body structure that emphasizes quietness and
portability.
In order to obtain the maximum performance and enjoyment from this product, we urge
you to read this Owner’s Manual thoroughly before using the instrument. Please keep this
Owners Manual, together with the warranty, in a safe place for later reference.
Contents
Included Accessories ...................................................................7
Parts and their Names ..................................................................8
Front ..........................................................................................8
Rear ..........................................................................................8
Battery Case/External Output (LINE OUT) Jack .......................9
Controls .....................................................................................9
Setup ............................................................................................12
Tuning .....................................................................................12
Attaching the Frame Unit ........................................................14
About the End Pin ...................................................................15
Attaching the Optional Accessories ........................................15
Preparing the Power Supply (How to Replace Batteries) .......16
Connection Example ...............................................................17
Turning the Power On and Off ................................................18
About the Mute ........................................................................18
Changing Strings ........................................................................19
Putting the Bass into the Soft Case ..........................................21
Specifications .............................................................................22
SLB300 Owner’s Manual
2
1. IMPORTANT NOTICE: DO NOT MODIFY
THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could
void your FCC authorization to use this product in
the USA.
3. NOTE: This product has been tested and found
to comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result
in harmful interference with other electronic
devices. This equipment generates/uses radio fre-
quencies and, if not installed and used according
to the instructions found in the users manual, may
cause interference harmful to the operation of
other electronic devices. Compliance with FCC
regulations does not guarantee that interference
will not occur in all installations. If this product is
found to be the source of interference, which can
be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to co-axial
type cable.
If these corrective measures do not produce satis-
factory results, please contact the local retailer
authorized to distribute this type of product. If you
can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those prod-
ucts distributed by Yamaha Corporation of Amer-
ica or its subsidiaries.
* This applies only to products distributed by Yamaha Corporation of America. (class B)
FCC INFORMATION (U.S.A.)
3
SLB300 Owners Manual
(can_b_02)
COMPLIANCE INFORMATION STATEMENT
(Supplier’s declaration of conformity procedure)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Electric Upright Bass
Model Name : SLB300
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may
cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
* This applies only to products distributed by Yamaha Corporation of
America.
(FCC SDoC)
SLB300 Owner’s Manual
4
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even
death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions
include, but are not limited to, the following:
This instrument contains no user-serviceable parts. Do not
open the instrument or attempt to disassemble or modify
the internal components in any way. If it should appear to
be malfunctioning, discontinue use immediately and have
it inspected by qualified Yamaha service personnel.
Repairs or part replacement should not be attempted unless
instructions are provided in the manual.
Do not expose the instrument to rain, use it near water or in
damp or wet conditions, or place on it any containers (such
as vases, bottles or glasses) containing liquids which
might spill into any openings. If any liquid such as water
seeps into the instrument, turn off the power immediately.
Then have the instrument inspected by qualified Yamaha
service personnel.
Do not put burning items, such as candles, on the unit. A
burning item may fall over and cause a fire.
Follow the precautions below. Failure to do so might result
in explosion, fire, overheating or battery fluid leakage.
- Do not tamper with or disassemble batteries.
- Do not dispose of batteries in fire.
- Do not attempt to recharge batteries that are not designed to be
charged.
- Keep the batteries separate from metallic objects such as
necklaces, hairpins, coins, and keys.
- Use the specified battery type (page 9) only.
- Use new batteries, all of which are the same type, same model,
and made by the same manufacturer.
- Always make sure all batteries are inserted in conformity with
the +/- polarity markings.
- When the batteries run out, or if the instrument is not to be
used for a long time, remove the batteries from the instrument.
- When using Ni-MH batteries, follow the instructions that came
with the batteries. Use only the specified charger device when
charging.
Keep batteries away from small children who might
accidentally swallow them.
If the batteries do leak, avoid contact with the leaked fluid. If
the battery fluid should come in contact with your eyes,
mouth, or skin, wash immediately with water and consult a
doctor. Battery fluid is corrosive and may possibly cause
loss of sight or chemical burns.
When one of the following problems occur, immediately
turn off the power switch (If you are using batteries, remove
all batteries from the instrument.) Then have the device
inspected by Yamaha service personnel.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the instrument.
- If any cracks or breakages exist on the instrument.
When moving any movable parts, be careful not to pinch
your fingers or hands, to avoid possible injury.
Do not carry the supplied soft case over your shoulder
while riding a motorcycle or bicycle, etc. Doing so could
cause you to fall or have an accident.
PRECAUTIONS
Do not open
Water warning
Fire warning
Battery
If you notice any abnormality
Handling warning
About the supplied soft case
DMI-7 1/2
5
SLB300 Owners Manual
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or
others, or damage to the instrument or other property. These precautions include, but are not limited
to, the following:
Assemble the instrument in the proper sequence by
following the assembly instructions in this manual. Also,
make sure to tighten the screws or bolts regularly. Failure
to do so might result in damage to the instrument or even
injury.
Before moving the instrument, remove all connected
cables, to prevent damage to the cables or injury to anyone
who might trip over them.
Do not stand the instrument in an unstable place, and make
sure to lay it on the floor. Putting it in an unstable position
could cause the instrument to fall and result in damage or
injury.
Handle the neck and the body when moving the instrument.
Handling the instrument by only the side plate unit could
result in malfunction to the side plate unit.
Before connecting the instrument to other electronic
components, turn off the power for all components. Before
turning the power on or off for all components, set all
volume levels to minimum.
Be sure to set the volumes of all components at their
minimum levels and gradually raise the volume controls
while playing the instrument to set the desired listening
level.
Do not insert your finger or hand in any gaps on the
instrument. Also take care that the frame unit and the
optional accessories does not pinch your finger. Failure to
do so might result in injury.
Do not rest your weight on, or place heavy objects on the
instrument, and do not use excessive force on the buttons,
switches or connectors.
Keep small parts out of the reach of infants. Your children
may accidentally swallow them.
Do not use the instrument for a long period of time at a
high or uncomfortable volume level, since this can cause
permanent hearing loss. If you experience any hearing loss
or ringing in the ears, consult a physician.
The ends of the strings are sharp and can cut fingers. Use
caution when changing strings.
When changing or adjusting strings, do not put your face
close to the instrument. The string may suddenly break
resulting in eye injury or other accidents.
Do not swing the supplied soft case or the strap. Doing so
could cause an accident
Always turn the power off when the instrument is not in use.
Make sure to discard used batteries according to local regulations.
Assembly
Transport / Installation
Connections
Handling caution
About the supplied soft case
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument.
DMI-7 2/2
SLB300 Owner’s Manual
6
NOTICE
To avoid the possibility of malfunction/damage to the product or damage to other
property, follow the notices below.
Handling
• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent the possi-
bility of panel disfiguration, damage to the internal components or unstable operation.
Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone,
or other electric devices. Otherwise, the instrument, TV, or radio may generate noise.
• When cleaning the instrument, use a soft cloth. Do not use paint thinners, solvents,
alcohol, cleaning fluids, or chemical-impregnated wiping cloths.
About the supplied soft case
Do not use the supplied soft case to store any other instrument not intended for use with
the supplied case.
• Do not drop or subject the supplied soft case to strong shock with the instrument stored
inside. Doing so may damage the instrument.
• Do not expose the supplied soft case to direct sunlight (such as in a car during the day),
or extremely high temperatures (such as close to a heater). Doing so may result in dis-
coloration or deterioration.
• Do not place near oils or chemicals. They may deteriorate the cover.
• Do not use the supplied soft case if it is torn or split.
About this manual
• The illustrations as shown in this manual are for instructional purposes only, and may
appear somewhat different from those on your instrument.
(rear_en_01)
The model number, serial number, power requirements, etc., may be found on or
near the name plate, which is at the rear of the unit. You should note this serial
number in the space provided below and retain this manual as a permanent
record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
7
SLB300 Owners Manual
Included Accessories
After opening the packaging, please check that all the parts listed below are
included.
• Main body x 1
• Owner’s Manual (this document) x 1
• List of service locations x 1
Optional Accessories
• Stand for SILENT Bass
TM
(BST1)
• Knee support for SILENT Bass
TM
(BKS2)
• Extension frame for SILENT Bass
TM
(BEF2)
To purchase these optional accessories, please inquire with your
authorized Yamaha dealer.
• Frame unit x 1 • End pin x 1 • Mute x 1
* Two AA batteries (alkaline or nickel hydride) are required
to use this product.
• Allen wrench x 1
• Soft case x 1
SLB300 Owner’s Manual
8
Parts and their Names
Battery Case/
Output Jack
Section
see page 9.
Front Rear
Frame unit
fixing knob 1
Frame unit
armrest
Controls
see page 9.
Frame unit
fixing knob 2
Nut
Tuning peg
Fingerboard
Neck
Frame unit
End pin
End pin stopper
Ta il w i re
Saddle
Pickup
(inside the slot
on the side of the
body)
Escutcheon
Tailpiece
Bridge
Body
4th string (E)
3rd string (A)
2nd string (D)
1st string (G)
9
SLB300 Owners Manual
Battery Case/External Output (LINE OUT) Jack
Controls
q[POWER] (power switch)
This switch turns the power for the built-in SRT POW-
ERED preamplifier on and off.
Power Switch and LINE OUT Jack Status Correspondence Table
This product is designed so that the power can be turned
on only when a plug (cable) is inserted into the LINE OUT
jack. When a plug is not inserted into the LINE OUT jack,
the power will remain off regardless of the position of the
power switch.
If the power switch is off while a plug (cable) is inserted
into the LINE OUT jack, the Piezo Pickup signal will be
directly output to the LINE OUT jack (passive output).
Passive output is used in emergency situations when
there are no batteries, or when using sound reproduction
on an external device, such as a preamplifier.
Since the power is turned off during passive output, the
SRT POWERED preamplifier will not operate. Except for
the power switch, the knobs on the control panel will all be
disabled.
Power switch
ON OFF
LINE OUT
jack
Plug inserted
Power on
SRT POWERED preamplifier
operating
Power off
Passive output
Plug not
inserted
Power off
Not operating
NOTICE
q
w
e
r
u
i
t
y
NOTE
SLB300 Owner’s Manual
10
w [VOLUME] knob
This adjusts the volume.
e Status display LED (directly beneath the volume control knob)
This displays information such as the BYPASS function status, SRT POWERED microphone
type, and remaining battery power. The LED status can be checked from the diagonal direction
(performance posture) relative to the knob.
r [TREBLE] knob
This adjusts the level of the upper frequencies (TREBLE). This uses a peaking filter to amplify or
decrease the characteristic frequencies optimized for this product.
Turn to the right to create a brighter sound that can cut through the sound of other instru-
ments in a band.
Turn to the left for a soft, natural sound fit for bowing.
t [BASS] knob
This adjusts the level of the lower frequencies (BASS). This uses a peaking filter to amplify or
decrease the fundamental frequencies mainly of the 3rd and 4th strings.
Turn to the right to emphasize the low frequencies and create a warm, fat sound.
Turn to the left to cut the low frequencies for a clean sound that does not clash with other low-
pitched instruments.
When using passive output with the power switch off, the signal output decreases relative to the length of
the connected cable. When using the SRT POWERED preamplifier with the power switch on, the cable
length has virtually no effect on the signal output.
Turn the power off or turn the output volume all the way down for any connected amplifier, powered
speaker, or the like before turning the power for this product on or off.
Status Orange Green Red
Power switch on
Flashes based on
microphone type
––
Switch to microphone type 1
and check selection status
Flashes 1 time
––
Switch to microphone type 2
and check selection status
Flashes 2 times
––
Switch to microphone type 3
and check selection status
Flashes 3 times
––
Using bypass
–On
Out-of-battery warning
––
Flashes
NOTE
NOTICE
11
SLB300 Owners Manual
y[BYPASS] button
This button bypasses all controls except for the [VOL-
UME] of the SRT POWERED preamplifier. You can use
this button to instantly switch between the processed
SRT POWERED sound and the dry signal output. While
the bypass function is enabled, the LED for e is lit up in
green.
u[BLEND] knob
This adjusts the amount of mixing between the signal
from the pickup and the simulated microphone signal.
Turn it all the way to the left to set the signal from the
pickup to 100%. Turn it all the way to the right to set the
simulated microphone signal to 100%.
i [MIC TYPE] button
This selects the type of microphone to be simulated in the SRT POWERED system. Press and
hold the microphone type switching button (BLEND knob) until the status display LED flashes to
change the microphone type. The microphone type switches in order as follows: microphone type
1 microphone type 2 microphone type 3 microphone type 1. If you press the button
quickly, you can check the microphone type currently selected from the number of flashes.
Microphone type 1: Rich
Well-balanced, rich sound from a classic vintage vacuum-tube microphone.
Microphone type 2: Simple
Clear, clean sound from a dynamic microphone.
Microphone type 3: Warm
Warm sound with low-frequency emphasis from a famous vacuum-tube microphone, different
from type 1.
If you want to output the dry sound while still in active
output, use the bypass function with the power switch
on.
q
w
e
r
u
i
t
y
NOTE
SLB300 Owner’s Manual
12
Setup
Tuning
The SILENT Bass
TM
is shipped from the factory with the bridge in place and the strings
slightly loosened. The bridges height is set to an average person’s height. Since the posi-
tion of the bridge will sometimes shift during transport, make sure to properly adjust the
position of the bridge before tuning the strings.
The lower side of the bridge supports the 1st string
(G), the higher side supports the 4th string (E). When
looking at the bridge from the side, the surface that
has a sharper curve should face the fingerboard (fac-
ing up when in the playing position). (Fig. 1)
The correct position for the bridge is where the surface
of the bridge facing the tailpiece is at a right angle to
the body surface on which the bridge rests. [Fig. 2]
Position the bridge so that its legs do not come in con-
tact with the escutcheon (the plastic part).
Adjustments If the Bridge Is Leaning
After tuning, check that the surface of the bridge fac-
ing the tailpiece is vertical to the body surface on
which the bridge rests. If it is leaning to one side,
slightly loosen the strings and then use both hands to
raise the bridge.
If, after tuning, the tailpiece is leaning to one side
when seen from the front, slightly loosen all the
strings and manually straighten the tailpiece. After
that, increase the tension of all the strings as evenly
as possible and then re-perform tuning.
[Fig. 1 :
Looking from the tailpiece]
Groove
E
A
D
G
4th string 1st string
[Fig. 2: Bridge stands
vertically to surface A]
Correct
*1 Check that the bridge is vertically aligned with surface A, on which the bridge rests.
*2 Surface B, on which the bridge does not rest, and surface A, on which the bridge does rest, are not par-
allel. Surface B, on which the bridge does not rest, cannot be used to check that the bridge is vertical.
Incorrect
Incorrect
Right
angle
Body
Surface A on which the bridge rests *1
Tailpiece
Surface B on which the
bridge does not rest *2
Fix the leaning
Saddle
Ta il p ie ce
Ta ll wi re
13
SLB300 Owners Manual
The height of the bridge for the SILENT Bass
TM
can be
adjusted. Turn the metal adjusters clockwise to lower
the bridge, and counter-clockwise to raise it. [Fig. 3]
The strings are tuned to the following pitches. The 1st
string is tuned to G, the 2nd string to D, the 3rd string
to A, and the 4th string to E. Use a piano, tuning fork,
tuner, etc., and adjust the pitch of each string using the
tuning pegs.
Tuning machine tension adjustment
The tuning machine tension regulates the amount of pressure
required to turn the tuners and can be adjusted using the sup-
plied Allen wrench.
If the tuning machine turns with very slight pressure
Rotate the adjustment screw to the right (clockwise: A).
If the tension is tight and the tuning machine is hard
to turn
Rotate the adjustment screw to the left (counter-clock-
wise: B).
Before adjusting the bridge height, loosen the strings in order to relieve pressure on the adjusters and
make it easier to rotate the adjusters. Rotating the adjusters with without reducing string tension can
result in damage to the bridge or strings, etc.
When adjusting the bridge height, make sure that the height of both legs is kept the same. Increasing
string tension on legs that are unequal in height can result in poor surface contact of the bridges feet,
causing inferior sound quality, noise, damage to the bridge, etc. (Fig. 3 *3).
Metal adjusters
[Fig. 3: Adjusting bridge height]
Counter-
clockwise
Lower
Higher
*3 Adjust to the same height.
*3 *3
Clockwise
NOTICE
Lower pitch
2nd string (D)
Raise pitch
1st string (G)
4th string (E)
3rd string (A)
A
B
SLB300 Owner’s Manual
14
Attaching the Frame Unit
The SILENT Bass
TM
is shipped from the factory with the frame unit removed from the
main body.
Before using this product, please properly attach the frame unit to the main body using
the following procedure.
Installation Procedure
1. Open the upper arm support on the frame unit, until it comes in contact with the stopper.
2. With the frame unit's arm section (fixing screw 2) still closed (raised), gently slide the indenta-
tion of the frame unit's upper part in the direction of “
2 Slide” in the figure below.
3. Tighten fixing screw 1.
4. Rotate the arm section counter-clockwise to open it up, and insert fixing screw 2 into the holder
on the bass instrument.
5. Tighten fixing screw 2 to secure the frame unit to the bass instrument.
Frame attachment is complete.
To remove the frame unit, simply reverse the procedure described above.
Securely tighten fixing knobs 1 and 2. Using the instrument with the attachments loose can result in
parts rattling or making noise during performance.
When transporting the instrument, always hold it by its neck or main body. Holding by the frame unit only
may result in damage to the frame unit.
When moving movable parts, be careful not to pinch your fingers, hands, or the
like.
Fixing knob 2
1 Open
Tighten
5
Arm section
2 Slide onto body
3 Tighten
Open
4
Upper Arm Support
Fixing knob 1
Receiver
Fixing knob 2
NOTICE
15
SLB300 Owners Manual
About the End Pin
The SILENT Bass
TM
is shipped from the factory
with its end pin removed from the main body
and stored separately in the soft case. Before
using the instrument, loosen the end pin stop-
per and insert the end pin, and then after deter-
mining a comfortable playing height, securely
tighten the end pin stopper.
Attaching the Optional Accessories
Knee Support for the SILENT Bass
TM
(BKS2)
With the optional BKS2 Knee Support, the instru-
ment can be leaned against the left knee when
playing while sitting on a stool, etc.
As shown in Fig. A, align the end of the metal frame
unit with the matching indentation on the knee sup-
port, and use the three screws to secure the sup-
port in place.
Extension Frame for the SILENT Bass
TM
(BEF2)
The optional BEF2 Extension Frame widens the
frame unit to provide greater instrument support.
As shown in Fig. B, use the two screws to secure
the support in place.
Make sure the end pin stopper is secured firmly to prevent the instrument from falling while you play.
To ensure optimal performance, the end pin is designed to fit into the bass instrument at an angle and
cannot be fully inserted. Trying to force the end pin all the way in or subjecting it to an impact can dam-
age parts inside the bass instrument. Proceed slowly and carefully when inserting or removing the end
pin.
Before attaching or removing any optional parts, remove the frame unit from the bass instrument and
place the frame on a stable surface.
Before playing the instrument, make sure that the optional parts are not loosely attached.
End pin stopper
Tighten
Loosen
End pin
NOTICE
[Fig. A]
BKS2
[Fig. B]
BEF2
NOTICE
SLB300 Owner’s Manual
16
Preparing the Power Supply (How to Replace Batteries)
The SILENT Bass
TM
uses batteries for its power source.
Before installing or removing the batteries, remove the cable from the output jack.
1. On the backside of the instrument, push
down the battery case's latch in the direction
of the “OPEN” arrow to remove the battery
case.
2. Insert the batteries into the case. Referring to
the illustration, make sure the batteries are
placed in the case with the polarity (+/-) prop-
erly aligned.
3. Push in the battery case all the way until you
hear a click.
When to Replace the Batteries
When the batteries are running low, the status display LED flashes in red. Promptly replace the
batteries.
With nickel hydride batteries, the discharge properties may cause the power to turn off before the
LED flashes in red.
When removing the battery case, tilt the instru-
ment body at an angle to prevent the battery
case from flying out.
AA batteries
(alkaline or
nickel hydride)
Latch
Battery case
NOTICE
Be careful of the following when replacing the batteries.
Battery shapes (battery terminals and external shapes, etc.) vary depending
on the battery manufacturer. Inserting a battery with a shape different from
the battery case may damage the instrument or the like. Even if the batteries
fit in, poor contact with the terminals can cause a fire.
Always follow the polarity signs (+/-) when inserting batteries. Improper
insertion can cause a fire.
If not using the instrument for a long period of time, remove the batteries
from the instrument. Failure to do so can cause battery drainage or damage
to the instrument due to battery leakage.
17
SLB300 Owners Manual
Connection Example
Refer to the connection example below and connect this product to an external device.
Turn off the power for all devices before performing connections.
When making connections, first check the shape of the connection jack, be sure to use a plug
cable that meets the jack standards, and make the connection firmly.
* All illustrations and figures are for instruction purposes. The actual specifications may vary.
Bass amplifier
SLB300
Mixer
DI
Preamplifier
Audio interface
Standard monaural
phone plug
SLB300 Owner’s Manual
18
Turning the Power On and Off
With a plug (cable) inserted into the LINE OUT jack of this product, push
the [POWER] switch up to turn the power on, and down to turn the power
off. When the power turns on, the status display LED will flash (page 10).
About the Mute
Since the SILENT Bass
TM
is designed with a pickup system that picks up string vibration,
the system can sometimes pick up string vibrations that occur between the bridge and
tailpiece. If this sound is bothersome or unwanted, you can mute it by attaching the sup-
plied mute onto the strings as shown in the illustration below.
To prevent the battery from being depleted, be sure to turn the power switch off after finish-
ing use. Also, remove the cable.
You can use this product even without batteries by turning the power switch off (to passive
output) and connecting the product to an external device that supports passive output.
When using an external device, connect a device (DI, etc.) that has input impedance of 10
MΩ or higher. Sufficient output and frequency characteristics may not be ensured if the
input impedance of the connected device is lower than the specified value.
To prevent faults in this product or the external device as well as noise, be careful regarding the
order in which you turn the power switch on or off and make connections.
Order for Turning the Power Switch Off and Making Connections (Example)
1. Lower the level of the channel to which this product is connected on the output device, such as a PA.
2. Turn off the power switch of this product.
3. Disconnect this product and the output device, such as a PA.
4. Connect this product and a DI or the like already connected to a PA or the like.
5. Check that the level of the channel to which a DI or the like is connected on the output device such as
a PA is lowered.
6. Turn on the switch of the DI or the like.
7. Raise the level of the channel to which a DI or the like is connected on the output device such as a PA.
NOTE
NOTICE
*Midway between
the bridge and the
tailpiece
Mute
Mute
* The effectiveness of the mute will be reduced if it is attached midway between the
bridge and the tailpiece.
* Midway between the
bridge and the tailpiece
19
SLB300 Owners Manual
Changing Strings
Make sure you purchase Double Bass strings. The SILENT Bass
TM
uses a string length of
1,040 mm (41”).
Winding the Strings
1. Hook the string’s ball end into the string hole on the tailpiece. Make sure that the ball end is
securely positioned in the end of the string hole slit.
* If the ball end is larger than the string hole, thread the opposite end of the string through the
hole from the back side of the tailpiece.
2. Pull the string down toward the end pin and wrap the string around the end of the tailpiece mak-
ing sure it fits into its corresponding groove at the bottom of the tailpiece. Pull the string up and
over the bridge.
Do not remove all strings at the same time. Make sure to change the strings one at a time.
NOTICE
The ends of the strings are sharp and can cut fingers. Use caution when
changing strings.
When changing or adjusting strings, do not put your face close to the instru-
ment. The string may suddenly break resulting in eye injury or other acci-
dents.
Tailpiece
String
Ball end
Ball end
SLB300 Owner’s Manual
20
3. Insert the end of the string into the hole on the peg, turn the peg and make one or two wraps to
one side of the hole as shown in the illustration below, and then make the remaining wraps in
the opposite direction. From the perspective at the front of the instrument, the first couple of
wraps on the 1st (G) and 2nd (D) strings should be to the left of the hole, whereas on the 3rd
(A) and 4th (E) strings, the first wraps should be made to the right.
4. Turn the pegs to perform tuning to match the sound of a piano, tuning fork, tuner, or the like.
For more information about tuning, see the cautionary notes under “Tuning” (page 12).
Before winding the strings, stand the bridge so that the surface of the bridge facing the tailpiece is
vertical to the body surface on which the bridge rests.
Before winding the strings, make sure that each string is positioned in its corresponding groove on
the bridge.
Before winding the strings, the adjust string length so that the string does not rub up against the
pegbox wall. Performing tuning while a string is rubbing up against the wall can result in a broken
string or the like.
When winding strings, be careful that the bridge is not pulled by the strings and pushed down
towards the fingerboard.
When not using the instrument for a long period of time, slightly loosen the strings before storage.
Always use the product with the bridge standing vertical to the surface on which the bridge rests. Using
the product with the bridge leaning to one side can shorten the service life of the bridge and reduce
sound quality.
Winding the 3rd
and 4th strings
Rotate the
tuning peg
as shown
Remaining
winds
Wind
once or
twice
Wind once
or twice
Remain-
ing winds
3rd string (A)
Winding the 1st
and 2nd strings
Rotate the
tuning peg
as shown
1st string (G)
4th string (E)
2nd string (D)
NOTICE
NOTICE
Correct
Incorrect
Incorrect
Right
angle
Body
Tailpiece
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Yamaha SLB300 Manualul proprietarului

Tip
Manualul proprietarului