Ubiquiti M365 Specificație

Marca: Ubiquiti

Model: M365

Tip: Specificație

Acest manual este potrivit și pentru

Carrier-Class

airMAX

BaseStation

Models:

PBM3, PBM365, PBM5

Introduction

Thank you for purchasing the Ubiquiti Networks

™

PowerBridge

™

M. This Quick Start Guide is designed to guide

you through the installation, and show you how to access the

airOS® Configuration Interface. This Quick Start Guide also

includes the warranty terms and is for use with the following

models:

Model Operating Frequency

PowerBridgeM3 3300 - 3700 MHz

PowerBridgeM365 3650 - 3675 MHz

PowerBridgeM5

Worldwide: 5170 - 5875 MHz

USA: 5745 - 5850 MHz

Package Contents

PowerBridgeM Pole Brackets

(Qty. 2)

Pole Clamps

(Qty. 2)

Carriage Bolts

(M8X135,

Qty. 4)

Carrier-Class

airMAX

™

BaseStation

Models:

PBM3, PBM365, PBM5

Flange Bolts

(M8X20,

Qty. 4)

Flange Nuts

(M8, Qty. 4)

PoE Adapter

(24V, 1A)

Power Cord Quick

Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Ports

Ethernet Port

(10/100) Mbps

Reset

Button

Port Cover U-Brackets

Ethernet Port The Ethernet port is a 10/100 Mbps port used

for data and supplies power to the PowerBridgeM. Power can

be provided by any of the following:

• PoE adapter (included)

• Ubiquiti Networks TOUGHSwitch

™

PoE

• Ubiquiti Networks EdgeRouter

™

PoE

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the

PowerBridgeM is already poweredon.

LEDs

Power The Power LED will light green when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light red when the wireless signal

strength is above -94 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light green when the wireless signal

strength is above -65 dBm.

Installation Requirements

• 13 mm or ½" wrench

• Flathead screwdriver

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Installation

To install the PowerBridgeM, perform the following steps:

1. The Port Cover is hinged to the PowerBridgeM and locked

with a screw. Use a flathead screwdriver to turn the locking

screw counter-clockwise until it is loose. Open the cover by

sliding it down and raising it up.

*720-00065-02*

720-00065-02

2. Connect an Ethernet cable to the Ethernet Port.

3. Close the Port Cover and lock it in place by turning the

locking screw clockwise.

4. Insert two Carriage Bolts into each Pole Bracket.

5. Connect the Pole Brackets to the U-Brackets using the four

Flange Bolts.

6. Mount the PowerBridgeM to the pole:

a. Position the Carriage Bolts around the pole at the

mounting location.

b. Slide a Pole Clamp onto each pair of Carriage Bolts.

c. Hand-tighten a Flange Nut on each Carriage Bolt.

Note: The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

7. Rotate the PowerBridgeM to the correct azimuth towards

the other end of the wireless link.

8. Adjust the elevation angle as needed:

a. Loosen the four Flange Bolts on the U-Brackets.

b. Adjust the PowerBridgeM to the desired elevation tilt.

c. Tighten all bolts and nuts to approximately

25 N-m (18 lb-ft).

Flange

Bolts

Powering the PowerBridgeM

The PowerBridgeM can be powered by the included PoE

Adapter or any of the following compatible PoE switches:

• TOUGHSwitch PoE, model TS-5-POE

• TOUGHSwitch PoE PRO, model TS-8-PRO

• EdgeRouter PoE, model ERPoe-5

Connecting to the PoE Adapter

1. Connect the other end of the Ethernet cable from the

PowerBridgeM to the Ethernet port labeled POE on the

PoEAdapter.

2. Connect an Ethernet cable from your LAN or computer to

the Ethernet port labeled LAN on the PoE Adapter.

3. Connect the Power Cord to the power port on the PoE

Adapter. Connect the other end of the Power Cord to a

power outlet.

Connecting to a PoE Switch

Connect the other end of the Ethernet cable coming from

the PowerBridgeM directly to a PoE port on a compatible

PoEswitch.

TOUGHSwitch PoE PRO Power Connection

Accessing airOS

Verify connectivity in the airOS Configuration Interface.

1. Make sure that your host machine is connected via

Ethernet to the PowerBridgeM.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser and type https://192.168.1.20

in the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

Note: U.S. product versions are locked to the

U.S. Country Code to ensure compliance with

FCCregulations.

The airOS Interface will appear allowing you to customize your

settings as needed.

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer’s responsibility to make sure the device is

operated within local country regulatory requirements.

Specifications

PBM3 / PBM365 / PBM5

Dimensions

445 x 416 x 34 mm

Weight 3.82 kg

Operating Frequency

M365

3300 - 3700 MHz

3650 - 3675 MHz

Worldwide: 5470 - 5825 MHz

USA: 5725 - 5850 MHz

Networking Interface (1) 10/100 Ethernet Port

Enclosure Outdoor UV Stabilized Plastic

Max. Power Consumption 8 W

Power Supply 24V, 1A PoE Supply Included

Power Method Passive PoE (Pairs 4, 5+; 7,8 Return)

Certications CE, FCC, IC

Mounting Pole Mounting Kit Included

Operating Temperature -30 to 80° C

Operating Humidity 5 to 95% Non-Condensing

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Cet appareil numérique de la classe A est conforme à la norme NMB-003

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a

separation distance of at least 113 cm from all persons and must not be located

or operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

considérant une distance de séparation de toute personnes d’au moins 113cm

et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou

transmetteur.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the product and it

must follow the CE marking.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Pagina se încarcă ...

Ubiquiti M365 Specificație

Marca: Ubiquiti

Model: M365

Tip: Specificație

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ubiquiti M365 Specification
italiano: Ubiquiti M365 specificazione

Lucrări conexe

Alte documente

Ubiquiti Networks TC-PRO Manual de utilizare