Samsung HW-J6001R Manual de utilizare

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

User manual

HW-J6000R

HW-J6001R

2

GETTING STARTED

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage is

present inside. It is dangerous to make any kind

of contact with any internal part of this product.

This symbol indicates that important literature

concerning operation and maintenance has

been included with this product.

Class II product : This symbol indicates that it does not require a safety connection to electrical

earth (ground).

AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC voltage.

DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC voltage.

Caution, Consult instructions for use : This symbol instructs the user to consult the user manual for

further safety related information.

WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a AC outlet with a protective grounding connection.

• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the

mains plug shall be readily operable.

CAUTION

• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the

apparatus.

• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power

plug must be easily and readily accessible at all times.

GETTING STARTED

ENG

3

GETTING STARTED

PRECAUTIONS

99.1mm 99.1mm

68.6

mm

99.1mm

Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker

located on the back of your product. Install your product horizontally, on a suitable base (furniture), with enough space

around it for ventilation (7~10 cm). Make sure the ventilation slots are not covered. Do not place the unit on amplifiers or

other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect

the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.

During thunderstorms, disconnect the AC plug from the

wall outlet. Voltage peaks due to lightning could damage

the unit.

Protect the product from moisture (i.e. vases), and

excess heat (e.g. a fireplace) or equipment creating

strong magnetic or electric fields. Disconnect the power

cable from the AC supply if the unit malfunctions. Your

product is not intended for industrial use. It is for

personal use only. Condensation may occur if your

product has been stored in cold temperatures. If

transporting the unit during the winter, wait approximately

2 hours until the unit has reached room temperature

before using.

Do not expose the unit to direct sunlight or other heat

sources. This could lead to overheating and cause the

unit to malfunction.

The batteries used with this product contain chemicals

that are harmful to the environment. Do not dispose of

batteries in the general household trash. Do not dispose

of batteries in a fire. Do not short circuit, disassemble, or

overheat the batteries. There is a danger of explosion if

the battery is incorrectly replaced. Replace only with the

same or equivalent type.

WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD. The remote control supplied

withthis product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can

cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away

from children. If the battery compartment does not close securely, stop using the product and keep it

away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek

immediate medical attention.

4

GETTING STARTED

Figures and illustrations in this User Manual are

provided for reference only and may differ from

actual product appearance.

CONTENTS

2 GETTING STARTED

2 Safety Information

5 What’s Included

6 DESCRIPTIONS

6 Top / Front Panel

7 Rear / Bottom Panel

8 Remote Control

11 INSTALLATION

11 Installing the Soundbar

11 Installing the Wall Mount

14 Placing the Soundbar on a TV stand

14 Installing the Soundbar as a Free-Standing

Unit

15 CONNECTIONS

15 Connecting the Subwoofer

17 Connecting the SWA-8000S

(Sold Separately)

19 Connecting to a TV

19 Connecting to a TV Using an HDMI (Digital)

Cable

20 Connecting to a TV Using a Digital Optical

Cable

20 TV SoundConnect

22 Connecting to External Devices

22 HDMI Cable

22 Optical or Analogue Audio Cable

23 USB

25 FUNCTIONS

25 Input Mode

26 Bluetooth

29 Software Update

31 TROUBLESHOOTING

31 Troubleshooting

32 APPENDIX

32 Specifications

ENG

5

GETTING STARTED

WHAT’S INCLUDED

BEFORE READING THE USER’S MANUAL

Note the following terms before reading the user manual.

+ Icons used in this manual

Icon Term Definition

Caution

Indicates a situation where a function does not operate or settings may be cancelled.

Note

Indicates tips or instructions on the page that help you operate a function.

Check for the supplied accessories shown below.

Remote Control /

Lithium Battery

(3V : CR2032)

Power Cord : 2 EA AC/DC Adapter HDMI Cable

430

Bracket-Wall : 2 EA Wall Mount Guide Holder-Fix Mount : 2 EA

● The appearance of the accessories may differ slightly from the illustrations above.

6

DESCRIPTIONS

TOP / FRONT PANEL

(Power) Button

Turns the power on and off.

VOL. - / +

Controls the volume level.

The numeric value of the volume level

appears in the front panel display.

Display

Displays the current mode.

(Source) Button

Selects the D.IN, AUX, HDMI, BT, TV, or USB

input.

● While the unit is powered on, pressing the

button for more than 3 seconds sets

the button to act as the

(Mute) button. To cancel the (Mute)

button setup, press the

button for

more than 3 seconds again.

● When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

● When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

● If you want to enjoy sound only from the Soundbar, you must turn off the TV's speakers in the Audio Setup

menu of your TV. Refer to the owner's manual supplied with your TV.

DESCRIPTIONS

ENG

7

DESCRIPTIONS

REAR / BOTTOM PANEL

DC 14V

AUX IN

OPTICAL IN

HDMI IN

HDMI OUT

(TV-ARC)

5V 0.5A

DC14V

5V 0.5A

DC 14V

(Power Supply In)

Connect the DC power adaptor to the

power supply jack, and then connect the

AC power adaptor plug to a wall outlet.

(USB Port)

Connect USB devices here to play

files on the devices.

OPTICAL IN (D.IN)

Connect to the digital

(optical) output of an

external device.

HDMI OUT (TV-ARC)

Outputs digital video and

audio signals simultaneously

using an HDMI cable.

HDMI IN

Inputs digital video and audio

signals simultaneously using an

HDMI cable. Use when connecting

a supported external device.

AUX IN

Connect to the Analogue output of an

external device.

LABEL

● When disconnecting the power cable of the AC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

● Do not connect this unit or other components to an AC outlet until all connections between components

are complete.

● Make sure to rest the AC/DC Adapter flat on a table or the floor. If you place the AC/DC Adapter so that it

is hanging with the AC cord input facing upwards, water or other foreign substances could enter the

Adapter and cause the Adapter to malfunction.

8

DESCRIPTIONS

REMOTE CONTROL

Repeat

Press to set the Repeat function during music playback from a USB device.

OFF - REPEAT : Cancels Repeat Playback.

TRACK - REPEAT : Plays a track repeatedly.

ALL - REPEAT : Plays all tracks repeatedly.

RANDOM - REPEAT : Plays tracks in random order.

(A track that has already been played may be played again.)

Mute

You can turn the volume down to 0 with the push of a button.

Press again to restore the sound to the previous volume level.

SOURCE

Press to select a source connected to the Soundbar.

Skip Forward

If there is more than one file on the device you are playing, and you press

the ] button, the next file is selected.

Bluetooth POWER

Press the Bluetooth POWER button on the remote to turn the Bluetooth

POWER On function on and off. See pages 21 and 27 for details.

SOUND

Surround Sound adds depth and spaciousness to the sound. Pressing the

SOUND button repeatedly cycles through the Surround Sound settings :

ON - SURROUND SOUND, OFF - SURROUND SOUND

SOUND EFFECT

You can select from 6 different sound modes - STANDARD (Original Sound),

MUSIC, CLEAR VOICE, SPORTS, MOVIE, and NIGHT MODE - depending

on the content you want to listen to.

Select the STANDARD mode if you want to enjoy the original sound.

* DRC (Dynamic Range Control)

Lets you apply dynamic range control to Dolby Digital.

Press and hold the SOUND EFFECT button for about 5 seconds in STANDBY

mode to turn the DRC (Dynamic Range Control) function on or off.

Press and hold the



button for about 5 seconds to turn the Anynet+ function

on or off.

OFF - ANYNET+, ON - ANYNET+

The Anynet+ function lets you control the Soundbar with the remote from an

Anynet+ compatible Samsung TV.

The Soundbar must be connected to the TV via an HDMI cable.

Press and hold the



button for about 5 seconds to turn the Auto Power Link

function on or off.

OFF - POWER LINK, ON - POWER LINK

* Auto Power Link

Synchronizes the Soundbar to a connected Optical source via the Optical jack

so it turns on automatically when you turn on your TV. (See page 20)

Auto Power Link function is only available in the D.IN mode.

ENG

9

DESCRIPTIONS

Volume

Adjusts the volume level of the unit.

Power

Turns the Soundbar on and off.

SOUND CONTROL

Press to select TREBLE, BASS, SUBWOOFER LEVEL, AUDIO SYNC,

REAR SPEAKER, or REAR LEVEL.

Then, use the ,  buttons to adjust the TREBLE or BASS volume from

-6 ~ +6, SUBWOOFER LEVEL volume from -12, -6 ~ +6.

Press and hold the SOUND CONTROL button for about 5 seconds to adjust the

sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2KHz, 2.5KHz, 5KHz

and 10KHz are selectable and each can be adjusted to a setting between -6 ~ +6.

If the Soundbar is connected to a digital TV and the video appears out of sync

with the audio, press the SOUND CONTROL button to sync the audio with the

video. Use the ,  buttons to set the audio delay between

0 ms ~ 300 ms. In USB mode, TV mode, and BT mode, the Audio Sync function

may not available.

To turn on or off of the rear speaker sound, select REAR SPEAKER in Sound

Control, and then adjust the volume between OFF-RS and ON-RS by using the

,  buttons.

To control the volume of the rear level sound, select REAR LEVEL in Sound

Control, and then adjust the volume between RS -6~+6 by using the , 

buttons.

Play / Pause

Press the

p

button to pause a file temporarily.

Press the

p

button again to play the selected file.

Skip Back

If there is more than one file on the device you are playing, and you press

the

[

button, the previous file is selected.

● The REAR SPEAKER and the REAR LEVEL mode are only available when you connect the SWA-8000S

(sold separately).

- If the SWA-8000S is disconnected, REAR SPEAKER and REAR LEVEL remain displayed but the

functions are not available.

● Operate the TV using the TV's remote control.

10

DESCRIPTIONS

+ Controlling the Soundbar using Your TV Remote Control

1. Press and hold the

SOUND

button for more than 5 seconds while the Soundbar is turned on.

2. "ON - TV REMOTE" appears on the Soundbar's display.

3. In the TV's menu, set the TV speaker to external speaker.

● Not available if the TV ARC function or HDMI mode is in use.

● All buttons are not available except the VOL +/- and the (Mute) buttons in this function.

● TV menus differ by manufacturer and model. Refer to the TV's user manual for further information.

● Manufacturers supporting this function:

- VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, GRUNDIG, Hisense, RCA

- This function may not be compatible with your TV's remote depending on the remote control's

manufacturer.

● To turn off this function, press the

SOUND

button for 5 seconds.

"OFF - TV REMOTE" appears on the Soundbar's display.

INSTALLING THE BATTERY IN THE REMOTE CONTROL

1. Use a suitable coin to turn the

remote control's battery cover

counterclockwise to remove it

as shown in the figure above.

2. Insert a 3V lithium battery. Keep the

positive (+) pole facing up when inserting

the battery. Put the battery cover on and

align the '●' marks side by side as

shown in the figure above.

3. Use a suitable coin to

turn the remote control

battery cover clockwise

as far as it will go to fix it

in place.

ENG

11

INSTALLATION

INSTALLING THE SOUNDBAR

INSTALLING THE WALL MOUNT

+ Installation Precautions

● Install on a vertical wall only.

● For the installation, avoid a location with high temperature or humidity, or a wall that cannot sustain the weight of

the set.

● Check the strength of the wall. If the wall is not strong enough to support the unit, reinforce the wall or install the

unit on a different wall that can support the unit's weight.

● Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board,

wood, etc.). If possible, fix the support screws into wall studs.

● Purchase wall mounting screws according to the type and thickness of the wall you will mount the Soundbar on.

- Diameter : M5

- Length: 35 mm or longer recommended.

● Connect cables from the unit to external devices before you install it on the wall.

● Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock.

5 cm or more

1. Place the installation guide against the wall surface.

• The installation guide must be level.

• If the TV is mounted on the wall, install the Soundbar at least 5 cm below the TV.

INSTALLATION

12

INSTALLATION

Center Line

2. Mark the location where the screws will go through on the wall, and then remove the installation guide.

Next, drill holes for the screws using an appropriately sized drill bit.

3.

Fasten the 2 Bracket-Wall pieces firmly to the wall at the marked locations using the appropriate screws.

4. Attach the Soundbar to the 2

Bracket-Wall

pieces as shown in the illustration.

ENG

13

INSTALLATION

DC 14V

AUX IN

OPTICAL IN

HDMI IN

HDMI OUT

(TV-ARC)

5V 0.5A

5. Insert a Holder-Fix Mount into each hole on the product’s bottom side. Tighten each Holder-Fix Mount to fix the

Soundbar to the 2 Bracket-Wall pieces.

● Do not hang onto the installed unit and avoid striking or dropping the unit.

● Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may cause an injury or

damage the product.

● When the unit is installed on a wall, please make sure that children do not pull any of the connecting

cables, as this may cause it to fall.

● For the optimal performance of a wall mount installation, install the speaker system at least 5 cm

below the TV, if the TV is mounted on the wall.

● For your safety, if you do not mount the unit on the wall, install it on a secure, flat surface where it is unlikely

to fall.

14

INSTALLATION

PLACING THE SOUNDBAR ON A TV STAND

Place the Soundbar on a TV stand.

1. Align the Soundbar’s centre with the centre of the base of the TV, and then carefully push it onto the stand as far

as it will go, as shown in the illustration. Be careful not to unbalance the TV.

INSTALLING THE SOUNDBAR AS A FREE-STANDING UNIT

1. Centre the Soundbar on the flat area in front of the TV.

● Install it on a level and firm surface.

ENG

15

CONNECTIONS

● Do not connect the power cord of this product or your TV to a wall outlet until all connections between

components are complete.

● Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

CONNECTING THE SUBWOOFER

CONNECTING TO THE SUBWOOFER AUTOMATICALLY

The Subwoofer's linking ID is preset at the factory and the main unit and subwoofer should link (connect wirelessly)

automatically when the main unit and subwoofer are turned on.

• When the subwoofer is completely connected, the blue LED Link Indicator on the subwoofer stops blinking and

glows continuously.

CONNECTING TO THE SUBWOOFER MANUALLY

If the blue LED light does not stop blinking when the main unit and subwoofer are turned on, please set the ID by

following the steps below.

● Important: Before you begin, put the battery into the remote. See page 10 for instructions.

POWER

1. Plug the power cords of the main unit and subwoofer into an AC wall outlet.

2. Press the ID SET button on the back of the subwoofer with a small, pointed object for 5 seconds.

• The STANDBY indicator turns off and the LINK indicator (Blue LED) blinks quickly.

3. While the main unit is powered off (in STANDBY mode), press and hold the (Mute) on the remote control for

5 seconds.

4. The ID SET message appears on the Soundbar's display.

5. To finalise the link, turn the main unit’s power on while the subwoofer’s Blue LED blinks.

• The main unit and the subwoofer should now be linked (connected).

• The LINK indicator (Blue LED) on the subwoofer should be glowing continuously and not blinking.

• If the LINK indicator is not solid blue, the linking process has failed. Turn off the main unit and start again from

Step 2.

• You can enjoy better sound from the wireless subwoofer by selecting a Sound Effect. (See page 8)

CONNECTIONS

16

CONNECTIONS

● Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

● If the main unit is powered off, the wireless subwoofer will in standy mode and the STANDBY LED on the

front will blink Red directly. (no blue LED).

● If you use a device that uses the same frequency (2.4GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

● The maximum transmission distance of the wireless signal between the main unit and subwoofer is about

10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is

between the main unit and the wireless subwoofer, the system may not operate at all, because the wireless

signal cannot penetrate metal.

● If the main unit doesn't make a wireless connection, follow steps 1-5 on the previous page to re-set the

connection between the main unit and wireless subwoofer.

● The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and

moisture.

● For optimal listening performance, make sure that the area around the wireless subwoofer location is clear

of any obstructions.

LED INDICATOR LAMP STATUS ON SUBWOOFER

LED Status Description Resolution

Red On

Standby (with the Soundbar main

unit turned off)

Check the power supply to the

Soundbar main unit

Connection failed

Connect again

(refer to the instructions on manual

connection in the user manual)

Blue

On

Successfully connected

(normal operation)

-

Blinking

Standby (with the Soundbar main

unit turned off)

Check the power supply to the

Soundbar main unit

Connection failed

Connect again

(refer to the instructions on manual

connection in the user manual)

Red and blue Blinking Malfunction Contact the service centre.

ENG

17

CONNECTIONS

CONNECTING THE SWA-8000S

(SOLD SEPARATELY)

● Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit

(SWA-8000S) to your Soundbar. (Sold separately)

● Before connecting to the Wireless Receiver Module, connect your subwoofer first.

● Use the speaker cable to connect the wireless receiver module to the speakers.

● Plug the power cable into a power outlet. The LED turns on.

1. While the main unit is powered off (in STANDBY mode), press and hold the (Mute) on the remote control for

5 seconds.

2. The ID SET message appears on the Soundbar's display.

3. Plug the power cord of the Wireless Receiver Module (SWA-8000S) into an AC wall outlet.

4. Turn on your Soundbar when the link indicator (Blue LED) on the SWA-8000S flickers fast.

5. When the link indicators (Blue LEDs) on your subwoofer and the SWA-8000S flash and then glow continuously, the

SWA-8000S is completely connected.

● This may take a few minutes.

● Once connected, your Soundbar and the Wireless Receiver Module are automatically reconnected even

after you turned them off and then on.

If the Wireless Receiver Module is not linked to your Soundbar (displaying the LED indicator in Red), connect

them as follows.

1. Turn off your Soundbar.

2. Press the (Mute) button on your remote control for 5~6 seconds until the ID SET message appears on your

Soundbar display.

3. Check the Wireless Receiver Module is in Standby status (displaying the LED indicator in Red).

4. Press the ID SET button on the back with a sharp pin for 5~6 seconds until the LINK LED indicator on the

Wireless Receiver Module blinks (in Blue).

5. Turn on your Soundbar with the button on your remote control and wait for a while. They are completely

connected to each other if you can see the LINK LED indicator is continuously lit (in Blue).

18

CONNECTIONS

CONNECTING THE SURROUND SPEAKERS

(SOLD SEPARATELY)

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

ID SET

L

R

Surround Speaker (L) Surround Speaker (R)

Wireless Receiver Module

● Place these speakers to the side of your listening position. If there isn't enough room, place these

speakers so they face each other. Position them about 60 to 90 cm above your ear, facing slightly

downward.

● Use the speaker cable to connect the Wireless Receiver Module to the Surround Speakers.

● Each speaker has a coloured label on its back or underside. Each cable has a single coloured band near its

end. Match the band on each cable to the speaker label by colour, and then connect the cable to the

speaker.

ENG

19

CONNECTIONS

CONNECTING TO A TV

● Important: Before you begin, put the battery into the remote. See page 10 for instructions.

CONNECTING TO A TV USING AN HDMI (DIGITAL) CABLE

DC 14V

AUX IN

OPTICAL IN

HDMI IN

HDMI OUT

(TV-ARC)

5V 0.5A

HDMI IN

HDMI OUT

(TV-ARC)

HDMI OUT

(TV-ARC)

HDMI Cable

1. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the back of the product to the HDMI IN jack on

your TV.

2. Press the button on the top panel of the Soundbar or the SOURCE button on the remote control to select

the D.IN mode.

● HDMI is an interface that enables the digital transmission of video and audio data with just a single

connector.

● If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.

● We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose

diameter is less than 14 mm.

● Anynet+ must be turned on.

● This function is not available if the HDMI cable does not support ARC.

20

CONNECTIONS

CONNECTING TO A TV USING A DIGITAL OPTICAL CABLE

DC 14V

AUX IN

OPTICAL IN

HDMI IN

HDMI OUT

(TV-ARC)

5V 0.5A

OPTICAL IN

OPTICAL OUT

Optical Cable

(not supplied)

1. Connect the OPTICAL IN (Audio) jack on the Soundbar to the OPTICAL OUT jack of the TV with a digital optical

cable.

2. Press the button on the top panel of the Soundbar or the SOURCE button on the remote control to select

the D.IN mode.

+ Auto Power Link

If you have connected the main unit to a TV with a digital optical cable, you can set the Auto Power function ON

to have the Soundbar turn on automatically when you turn the TV on.

1. Connect the Soundbar and

a TV

with a digital optical cable (not supplied).

2. Press the button on the main unit’s top panel or the SOURCE button on the remote control to select the

D.IN

mode.

3. Press the



button on the remote control for 5 seconds to turn Auto Power Link on or off.

● Auto Power Link is set to ON by default.

● Depending on the connected device, Auto Power Link may not function.

TV SOUNDCONNECT

You can enjoy TV sound through your Soundbar when it is connected to a Samsung TV that supports the

TV SoundConnect function.

Connect

1. Turn on the TV and Soundbar.

2. Press the button on the main unit’s top panel or the SOURCE button on the remote control to select the TV

mode.

3. On the TV, a message asking whether to enable the TV SoundConnect function appears.

4. Select <Yes> using the TV's remote control to finish connecting the TV and Soundbar.

Pagina se încarcă ...

Samsung HW-J6001R Manual de utilizare

Samsung HW-J6001R Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente