Panasonic SC-HC19EB Manualul proprietarului

Marca: Panasonic

Model: SC-HC19EB

Categorie: Ceasuri inteligente

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

Operating Instructions

Compact Stereo System

Model No. SC-HC29

SC-HC19

RQT9874-1R

Thank you for purchasing this product.

For optimum performance and safety, please read these instructions carefully.

Please keep this manual for future reference.

“EB” indicates the United Kingdom model.

The installation instructions are on page 16.

Please read these instructions carefully before installing.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 1 Friday, April 18, 2014 9:46 AM

RQT9874

These operating instructions are applicable for models

SC-HC29 and SC-HC19.

Unless otherwise indicated, illustrations in these

operating instructions are of SC-HC29. Your system and

the illustrations can look differently.

Bottom of product

Table of contents

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . .2

Caution for AC mains lead . . . . . . . . . . . . . . . . . . . .3

Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . .3

About Bluetooth

. . . . . . . . . . . . . . . . . . . . . . . . . . .4

Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Sales and Support Information . . . . . . . . . . . . . . . .4

Making the connections . . . . . . . . . . . . . . . . . . . . . .5

Preparing the remote control . . . . . . . . . . . . . . . . . .5

Overview of controls. . . . . . . . . . . . . . . . . . . . . . . . .6

Preparing the media . . . . . . . . . . . . . . . . . . . . . . . . .7

One-Touch Connection (NFC) . . . . . . . . . . . . . . . . .8

Media playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Clock and timers. . . . . . . . . . . . . . . . . . . . . . . . . . .11

Sound effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

External equipment. . . . . . . . . . . . . . . . . . . . . . . . .12

Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Attaching the unit to a wall (optional) . . . . . . . . . .16

Safety precautions

WARNING!

Unit

• To reduce the risk of fire, electric shock or product

damage,

– Do not expose this unit to rain, moisture, dripping or

splashing.

– Do not place objects filled with liquids, such as

vases, on this unit.

– Use only the recommended accessories.

– Do not remove covers.

– Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

– Do not let metal objects fall inside this unit.

• To prevent injury, this apparatus must be securely

attached to the wall in accordance with the installation

instructions.

AC mains lead

• The mains plug is the disconnecting device. Install this

unit so that the mains plug can be unplugged from the

socket outlet immediately.

CAUTION!

Unit

• To reduce the risk of fire, electric shock or product

damage,

– Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this

unit is well ventilated.

– Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

– Do not place sources of naked flames, such as

lighted candles, on this unit.

• This unit is intended for use in moderate climates.

• This unit may receive radio interference caused by

mobile telephones during use. If such interference

occurs, please increase separation between this unit

and the mobile telephone.

• This unit utilizes a laser. Use of controls or adjustments

or performance of procedures other than those

specified herein may result in hazardous radiation

exposure.

Battery

• Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the

manufacturer.

• When disposing the batteries, please contact your

local authorities or dealer and ask for the correct

method of disposal.

• Do not heat or expose to flame.

• Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and

windows closed.

• Do not break open or short-circuit the battery.

• Do not charge the alkaline or manganese battery.

• Do not use the battery if the cover has peeled off.

• Remove the battery if you do not use the remote

control for a long period of time. Keep in a cool, dark

area.

SC-HC29 :

SC-HC19 :

Indicate features applicable to SC-HC29.

Indicate features applicable to SC-HC19.

Product Identification Marking is located on the bottom

of the unit.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 2 Friday, April 18, 2014 9:46 AM

RQT9874

Caution for AC mains lead

(For the AC mains plug of three pins)

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three pin

mains plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that

the replacement fuse has a rating of 5-ampere and that it

is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the

body of the fuse.

If the plug contains a removable fuse cover you must

ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until

a replacement cover is obtained.

A replacement fuse cover can be purchased from your

local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type of AC

mains plug (figures A and B). Confirm the AC mains plug

fitted and follow the instructions below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

Supplied accessories

Check and identify the supplied accessories.

For the United Kingdom and Ireland

Use numbers indicated in parentheses when asking for

replacement parts. (Product numbers correct as of

December 2013. These may be subject to change.)

 1 AC mains lead

For the United Kingdom and Ireland

(K2CT2YY00097)

For others

(K2CQ2YY00119)

 1 FM indoor antenna

(RSAX0002)

 For the United Kingdom and Ireland

1 Antenna plug adaptor

(K1YZ02000013)

 1 Remote control

SC-HC29

(N2QAYB000944)

SC-HC19

(N2QAYB000948)

 1 Remote control battery

Figure A Figure B

Fuse cover

Fuse (5 ampere)

Wall mount kit

 2 Wall mount brackets

(RSC1262)

 1 Screw

(XTB3+8JFJK-J)

 1 Safety holder

(RSC1266)

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 3 Friday, April 18, 2014 9:46 AM

RQT9874

About Bluetooth

SC-HC29

Frequency band

• This system uses the 2.4 GHz frequency band.

Certification

• This system conforms to the frequency restrictions and

has received certification based on frequency laws.

Thus, a wireless permit is not necessary.

• The actions below are punishable by law:

– Taking apart or modifying the main unit.

– Removing specification indications.

Restrictions of use

• Wireless transmission and/or usage with all Bluetooth

equipped devices is not guaranteed.

• All devices must conform to standards set by

Bluetooth SIG, Inc.

• Depending on the specifications and settings of a

device, it can fail to connect or some operations can be

different.

• This system supports Bluetooth

security features.

But depending on the operating environment and/or

settings, this security is possibly not sufficient.

Transmit data wirelessly to this system with caution.

• This system cannot transmit data to a Bluetooth

device.

Range of use

• Use this device at a maximum range of 10 m.

•

The range can decrease depending on the environment,

obstacles or interference.

Interference from other devices

• This system may not function properly and troubles

such as noise and sound jumps may arise due to radio

wave interference if this unit is located too close to

other Bluetooth

devices or the devices that use the

2.4 GHz band.

• This system may not function properly if radio waves

from a nearby broadcasting station, etc. is too strong.

Intended usage

• This system is for normal, general use only.

• Do not use this system near an equipment or in an

environment that is sensitive to radio frequency

interference (example: airports, hospitals, laboratories,

etc.).

Licenses

Sales and Support Information

For the United Kingdom and Ireland

Customer Communications Centre

• For customers within the UK: 0844 844 3899

• For customers within Ireland: 01 289 8333

• Monday – Friday 9:00am – 5:00pm

(Excluding public holidays).

• For further support on your product, please visit our

website: www.panasonic.co.uk

Direct Sales at Panasonic UK

• Order accessory and consumable items for your

product with ease and confidence by phoning our

Customer Communications Centre

Monday – Friday 9:00am – 5:00pm

(Excluding public holidays).

• Or go on line through our Internet Accessory ordering

application at www.pas-europe.com

• Most major credit and debit cards accepted.

• All enquiries transactions and distribution facilities are

provided directly by Panasonic UK.

• It couldn’t be simpler!

• Also available through our Internet is direct shopping

for a wide range of finished products. Take a browse

on our website for further details.

Panasonic cannot be held responsible for data and/or

information that can possibly be compromised during a

wireless transmission.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

The Bluetooth

word mark and logos are owned by the

Bluetooth SIG, Inc. and any use of such marks by

Panasonic Corporation is under license. Other

trademarks and trade names are those of their

respective owners.

Google Play and Android are trademarks of Google Inc.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 4 Friday, April 18, 2014 9:46 AM

RQT9874

Making the connections

Connect the AC mains lead only after all the other

connections have been made.

1 Connect the FM indoor antenna.

2 Connect the AC mains lead.

Do not use an AC mains lead from other equipment.

Conserving power

The system consumes a small amount of power

(Z“Specifications”) when it is in standby mode.

Disconnect the power supply if you do not use the

system.

Some settings will be lost after you disconnect the

system. You have to set them again.

Note:

• These speakers do not have magnetic shielding.

Do not put them near TVs, PCs or other equipment

easily influenced by magnetism.

• Tape the antenna to a wall with the least amount of

interference.

• Use an outdoor antenna if the reception is poor.

Preparing the remote control

Use alkaline or manganese battery.

Install the battery so that the poles (+ and –) align with

those in the remote control.

For the United Kingdom and Ireland

Connect the FM outdoor antenna.

Use an outdoor antenna if the reception is poor.

Note:

• Do not use the outdoor antenna during a lightning

storm.

• Disconnect the outdoor antenna if you do not use the

system.

For the United Kingdom and Ireland

CAUTION!

Keep the antenna plug adaptor out of reach of

children to prevent swallowing.

Adhesive tape

(not supplied)

FM outdoor antenna

(not supplied)

75  coaxial cable

(not supplied)

Antenna plug adaptor

(For the AC mains plug of three pins)

READ THE “Caution for AC mains lead” BEFORE

CONNECTION.

To household

mains socket

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 5 Friday, April 18, 2014 9:46 AM

RQT9874

Overview of controls

Do the procedures with the remote control. You can also use the buttons on the main unit if they are the same.

A Standby/on switch [`], [1]

Press to switch the unit from on to standby mode or

vice versa. In standby mode, the unit is still

consuming a small amount of power.

B Select the audio source

On the remote control:

Press the corresponding button to select the source.

On the main unit:

C Basic playback control

D View the setup menu

E View the content information

F Select or confirm the option

G Open or close the sliding door

H Decrease the brightness of the display panel

To cancel, press the button again.

I Adjust the volume level

J Mute the sound

To cancel, press the button again.

“MUTE” is also cancelled when you adjust the volume

or when you switch off the system.

K View the play menu

L Select the sound effects

M SC-HC29

AUX IN terminal

N USB port ( )

SC-HC29

DC OUT terminal (Z“Charging a portable device”)

O SC-HC29

Select “BLUETOOTH” as the audio source

To start Bluetooth

pairing, press and hold the button.

SC-HC19

Select the dynamic bass effect

P SC-HC29

NFC touch area

Q Sliding door

R Display panel

S Remote control sensor

Distance: Within approximately 7 m

Angle: Approximately 20° up and down, 30° left and

right

Top view

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 6 Friday, April 18, 2014 9:46 AM

RQT9874

Preparing the media

Disc

1 SC-HC29

Press [USB/CD] to select “CD”.

SC-HC19

Press [CD].

2 Press [CD x] (main unit: [x OPEN/CLOSE]) to open

the sliding door.

Put in a disc with the label facing towards you.

3 Press [CD x] (main unit: [x OPEN/CLOSE]) again

to close the sliding door.

Keep fingers away from the sliding door when it is

closing.

USB

SC-HC29

Press [USB/CD] to select “USB”.

SC-HC19

Press [USB].

Note:

Do not use a USB extension cable. The system cannot

recognise USB device connected through a cable.

Bluetooth

SC-HC29

You can connect and play an audio device wirelessly

through Bluetooth

Preparation

• Switch on the Bluetooth

feature of the device and put

the device near the system.

• Read the operating instructions of the device for

details.

█ Pairing a device

Preparation

If this system is connected to a Bluetooth

device,

disconnect it (Z“Disconnecting a device”).

Press [ ] to select

“BLUETOOTH”

If “PAIRING” is shown, continue with step 4.

Press [PLAY MENU] to select “PAIRING”.

Or press and hold [ –PAIRING] on the main unit until

“PAIRING” is shown. Continue with step 4.

Press [

] to select “OK? YES” and then press [OK].

“PAIRING” is shown.

To cancel, select “OK? NO”.

4 Select “SC-HC29” from the Bluetooth

menu of the

device.

If prompted for a passkey, input “0000”.

The device connects with this system automatically

after pairing is complete.

The name of the connected device is shown for a few

seconds.

Note:

You can pair up to 8 devices with this system. If a 9th device

is paired, the device that has not been used for the longest

time will be replaced.

█ Connecting a device

Preparation

If this system is connected to a Bluetooth

device,

disconnect it (Z“Disconnecting a device”).

1 Press [ ]

to select

“BLUETOOTH”.

“BLUETOOTH READY” is shown.

2 Select “SC-HC29” from the Bluetooth

menu of the

device.

The name of the connected device is shown for a few

seconds.

3 Start playback on the device.

Note:

• A device must be paired to connect.

• This system can only connect to one device at a time.

• When “BLUETOOTH” is selected as the source, this

system will automatically try to connect to the last

connected device.

█ Disconnecting a device

Press [ ] to select

“BLUETOOTH”

Press [PLAY MENU] repeatedly to select

“DISCONNECT?”.

Press [

] to select “OK? YES” and then press [OK].

“BLUETOOTH READY” is shown.

To cancel, select “OK? NO”.

Using the main unit

Press and hold [ –PAIRING] until “PAIRING” is shown.

Note:

A device is disconnected when you:

• Select a different source.

• Move the device out of the maximum range.

• Disable the Bluetooth

transmission of the device.

• Switch off the system or the device.

USB device

(not supplied)

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 7 Friday, April 18, 2014 9:46 AM

RQT9874

One-Touch Connection (NFC)

SC-HC29

For NFC-compatible Bluetooth

devices (Android™

devices) only

Simply by touching an NFC (Near Field

Communication)-compatible Bluetooth

device on the

system, you can complete all preparations, from

registering a Bluetooth

device to establishing a

connection.

Preparation

Switch on the NFC feature of the device.

1 Press [ ]

to select

“BLUETOOTH”.

2 Touch and hold the device on the NFC touch area of

the main unit [ ].

– Hold the device until it beeps, vibrates or displays a

pop-up window, and then move the device away

from the system.

– Once the registration and connection of the device

is complete, the name of the connected device is

shown on the system for a few seconds.

– When the connection is not established even if the

device has touched the NFC touch area, change its

touching position. The connection may improve if

you use the “Panasonic Music Streaming” app.

3 Start playback on the device.

Note:

• While connected, you can connect another device by

touching and holding it on the NFC touch area of the main

unit. The previous device will be disconnected

automatically.

• Depending on the device:

– The one-touch connection may not work.

– The position of the NFC touch area of the device may be

different.

– When the connection is established, playback may start

automatically.

Media playback

The following marks indicate the availability of the feature.

Basic playback

CD USB BLUETOOTH

Note:

SC-HC29

Depending on the Bluetooth

device, some operations may

not work.

Viewing available information

CD USB BLUETOOTH

You can view the available information on the display panel.

Press [DISPLAY].

Note:

• Maximum characters that can be shown:

CD USB : approximately 32

BLUETOOTH : approximately 16

• This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.

• Text data that the system does not support can show

differently.

• Example: MP3 album and track number display.

Android™ device version lower than 4.1 requires the

installation of the “Panasonic Music Streaming” app

(free of charge).

A Enter “Panasonic Music Streaming” in the search

box of Google Play™ to search and then select

“Panasonic Music Streaming”.

B Start the app.

– Follow the instructions to complete the settings.

– Make sure to use the latest version of the app.

CD :

USB :

BLUETOOTH :

CD-R/RW in CD-DA format or with MP3 files.

USB device with MP3 files.

Bluetooth

device.

Play Press [4/9].

Stop Press [8].

USB

The position is memorised.

“RESUME” is shown.

Press again to stop fully.

Pause Press [4/9].

Press again to continue playback.

Skip Press [2/3] or [5/6] to skip track.

CD USB

Press [R, T] to skip MP3 album.

Search Press and hold [2/3] or [5/6].

Album

number

Track

number

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 8 Friday, April 18, 2014 9:46 AM

RQT9874

Play menu

CD USB

Press [PLAY MENU] repeatedly to select

“PLAYMODE” or “REPEAT”.

Press [

] to select the setting and then press [OK].

Note:

• During random playback, you cannot skip to tracks which

have been played.

• The setting is cancelled when you open the sliding door.

Link mode

BLUETOOTH

You can change the link mode to suit the connection type.

Preparation

If this system is connected to a Bluetooth

device,

disconnect it (Z“Disconnecting a device”).

Press [PLAY MENU]

repeatedly

to select

“LINK MODE”.

Press [

] to select the mode and then press [OK].

Note:

• The default setting is “MODE 2”.

• Select “MODE 1” if the sound is interrupted.

Input level

BLUETOOTH

You can change the input level setting if the sound input

level of the Bluetooth

transmission is too low.

1 Press [PLAY MENU]

repeatedly

to select

“INPUT LEVEL”.

2 Press [R, T] to select the level and then press [OK].

Note:

• The default setting is “LEVEL 0”.

• Select “LEVEL 0” if the sound is distorted.

█ Note on disc

• This system can play CD-R/RW with CD-DA or MP3

format content.

• Before playback, finalise the disc on the device it was

recorded on.

• Some CD-R/RW cannot be played because of the

condition of the recording.

█ Note on USB device

• This system does not guarantee connection with all

USB devices.

• This system supports USB 2.0 full speed.

• This system can support USB devices of up to 32 GB.

• Only FAT 12/16/32 file system is supported.

█ Note on MP3 file

• Files are defined as tracks and folders are defined as

albums.

• Tracks must have the extension “.mp3” or “.MP3”.

• Tracks will not necessarily be played in the order you

recorded them.

• Some files can fail to work because of the sector size.

MP3 file on disc

• This system can access up to:

– 255 albums (including root folder)

– 999 tracks

– 20 sessions

• Disc must conform to ISO9660 level 1 or 2

(except for extended formats).

MP3 file on USB device

• This system can access up to:

– 800 albums (including root folder)

– 8000 tracks

– 999 tracks in one album

PLAYMODE

OFF

PLAYMODE

Cancel the setting.

1-TRACK

Play one selected track.

Press [2/3] or [5/6] to

select the track.

1-ALBUM

Play one selected MP3 album.

Press [R, T] to select the MP3 album.

RANDOM

RND

Play all tracks randomly.

1-ALBUM

RANDOM

1 RND

Play all tracks in one selected MP3

album randomly.

Press [R, T] to select the MP3 album.

REPEAT

OFF REPEAT Cancel the setting.

ON REPEAT Repeat playback.

MODE 1 Emphasis on connectivity.

MODE 2 Emphasis on sound quality.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 9 Friday, April 18, 2014 9:46 AM

RQT9874

Radio

Preparation

SC-HC29

Press [RADIO/AUX] to select “FM”.

SC-HC19

Press [RADIO].

Manual tuning

Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

Press [

] to select “MANUAL” and then press [OK].

Press [

] or [

] to tune in to the station.

To tune automatically, press and hold the button until

the frequency starts changing quickly.

“STEREO” is shown when a stereo broadcast is being

received.

Memory presetting

You can preset up to 30 FM stations.

█ Automatic presetting

1 Press [PLAY MENU] to select “A.PRESET”.

2 Press [R, T] to select “LOWEST” or “CURRENT”

and then press [OK].

The tuner presets all the stations it can receive into

the channels in ascending order.

To cancel, press [8].

█ Manual presetting

Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

Press [

] to select “MANUAL” and then press [OK].

Press [

] or [

] to tune in to the station.

Press [OK].

Press [

] to select a preset number and then press

[OK].

Do steps 3 through 5 again to preset more stations.

The new station replaces any station that occupies

the same preset number.

█ Selecting a preset station

Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

Press [

] to select “PRESET” and then press [OK].

Press [

] or [

] to select the preset

station.

Improving the sound quality

1 Press [PLAY MENU] repeatedly to select

“FM MODE”.

Press [

] to select “MONO” and then press [OK].

To cancel, select “STEREO”.

“MONO” is also cancelled when you change the

frequency.

To memorise the setting

Continue with step 4 of “Manual presetting”.

Checking the signal status

Press [PLAY MENU] repeatedly to select “FM STATUS”

and then press [OK].

RDS broadcasting

This system can show the text data transmitted by the

radio data system (RDS) available in some areas.

Press [DISPLAY].

Note:

RDS may not be available if the reception is poor.

LOWEST Tuning begins from the lowest frequency.

CURRENT Tuning begins from the current frequency.

FM The FM signal is in monaural.

The system is not tuned in to a station.

FM ST The FM signal is in stereo.

FM MONO “MONO” is selected as the “FM MODE”.

PS Programme service

PTY Programme type

FREQ Frequency

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 10 Friday, April 18, 2014 9:46 AM

RQT9874

Clock and timers

Setting the clock

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [R, T] to set the time and then press [OK].

To check the time

Press [SETUP] repeatedly to select “CLOCK” and then

press [OK].

In standby mode, press [DISPLAY].

Note:

Reset the clock regularly to maintain accuracy.

Sleep timer

The sleep timer switches off the system after the set time.

1 Press [SETUP] to select “SLEEP”.

2 Press [R, T] to select the setting (in minutes) and

then press [OK].

To cancel, select “OFF”.

Note:

• The remaining time is always shown on the display.

The display changes temporarily when you perform other

operations.

• The sleep timer can be used together with the play timer.

• The sleep timer always comes first. Be sure not to set an

overlap of timers.

Play timer

(Except for Bluetooth

source)

You can set the timer to come on at a certain time to

wake you up.

Preparation

Set the clock.

Press [SETUP] repeatedly to select “TIMER ADJ”.

Press [

] to set the start time and then press [OK].

3 Do step 2 again to set the end time.

Press [

] to select the source you want to play

and then press [OK].

To start the timer

1 Press [SETUP] repeatedly to select “TIMER SET”.

2 Press [R, T] to select “SET” and then press [OK].

“#” is shown.

To cancel, select “OFF”.

The system must be switched off for the timer to

operate.

To check the setting

Press [SETUP] repeatedly to select “TIMER ADJ” and

then press [OK].

In standby mode, press [DISPLAY] two times.

Note:

•

The timer starts at a low volume and increases gradually to

the preset level.

• The timer comes on at the set time every day if the timer is on.

•

If you switch off the system and then switch on again while

a timer is in operation, the timer will not stop at the end time.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 11 Friday, April 18, 2014 9:46 AM

RQT9874

Sound effects

Press [SOUND] repeatedly to select the sound effect.

Press [

] to select the setting and then press [OK].

Note:

The default setting is underlined. Changed settings will be

kept until it is changed again, unless otherwise indicated.

External equipment

SC-HC29

You can play music from a portable audio equipment.

Preparation

• Switch off the equaliser (if any) of the portable audio

equipment to prevent sound distortion.

• Decrease the volume of the system and the portable

audio equipment before you connect or disconnect the

portable audio equipment.

1 Connect the portable audio equipment.

Plug type: Ø 3.5 mm stereo (not supplied)

2 Press [RADIO/AUX] to select “AUX”.

3 Play the portable audio equipment.

To adjust the input level

Press [SOUND] repeatedly to select “INPUT LEVEL”.

Press [

] to select “NORMAL” or “HIGH” and

then press [OK].

Note:

• The default setting is “NORMAL”.

• Select “NORMAL” if the sound is distorted during “HIGH”

input level.

• Read the operating instructions of the portable audio

equipment for details.

• Components and cables are sold separately.

Others

Auto off

This system automatically switches off when you do not

use it for approximately 20 minutes.

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Note:

• This function does not work when you are in radio source.

•

SC-HC29

This function does not work when a Bluetooth

device is

connected.

Bluetooth

standby

SC-HC29

This function automatically switches on the system when

you establish a Bluetooth

connection from a paired

device.

1 Press [SETUP] repeatedly to select

“BLUETOOTH STANDBY”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Charging a portable device

SC-HC29

This system can supply power to a portable device, such

as Android™ smartphone, connected to the USB port.

Note:

• Use a cable compatible with the device.

• Use the charger supplied with the device if power is not

supplied to the device.

• Do not use a cable or connect a device that exceeds the

rated value of 5 V, 1.5 A.

• Examine the screen of the device to check if charging is

complete. Disconnect the device after charging.

• Depending on the device, power may not be supplied to it.

• Read the operating instructions of the device for details.

Checking the software version

1 Press [SETUP] repeatedly to select “SW VER.” and

then press [OK].

The software version is shown.

2 Press [OK] again to exit.

Maintenance

To clean this system, wipe with a soft, dry cloth.

• Never use alcohol, paint thinner or benzine to clean this

system.

• Before using chemically treated cloth, read the

instructions that came with the cloth carefully.

PRESET EQ “HEAVY”, “SOFT”, “CLEAR”, “VOCAL” or

“FLAT”

BASS –4 to +4

TREBLE –4 to +4

D.BASS “ON D.BASS” or “OFF D.BASS”

SURROUND “ON SURROUND” or “OFF SURROUND”

Portable audio

equipment

(not supplied)

Audio cable

(not supplied)

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 12 Friday, April 18, 2014 9:46 AM

RQT9874

Troubleshooting

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or

if the solutions indicated do not solve the problem,

consult your dealer for instructions.

█ Common problems

The unit does not work.

• The safety device has been activated. Do the following:

1. Press [1] on the main unit to switch the unit to standby

mode. If the unit does not switch to standby mode,

– Press and hold the button for a minimum of

10 seconds. Or,

– Disconnect the AC mains lead and connect it again.

2. Press [1] again to switch on the unit. If the problem

persists, consult your dealer.

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the cause,

and then switch on again. It can be caused by straining of

the speakers through excessive volume or power, and

when using the system in a hot environment.

A humming sound can be heard during playback.

• An AC mains lead or fluorescent light is near the cables.

Keep other appliances and cords away from the cables of

this system.

Noise is heard.

• Depending on the device, noise may be heard if the device

is connected to the AUX IN and DC OUT terminals at the

same time. Disconnect the cable from the DC OUT

terminal.

█ Disc

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

•

Replace the disc if it is scratched, warped, or non-standard.

• There is condensation. Let the system dry for 1 to 2 hours.

█ USB

The USB device or the contents in it cannot be read.

• The format of the USB device or the contents in it are not

compatible with the system.

• USB devices with storage capacity of more than 32 GB

cannot work in some conditions.

Slow operation of the USB device.

• Large content size or large memory USB device takes

longer time to read.

The elapsed time shown is different from the actual

play time.

• Transfer the data to another USB device or backup the

data and reformat the USB device.

█ Bluetooth

Pairing cannot be done.

• Check the Bluetooth

device condition.

• The device is out of the 10 m communication range.

Move the device nearer to the system.

The device cannot be connected.

• The pairing of the device was unsuccessful. Do pairing

again.

• The pairing of the device has been replaced. Do pairing

again.

• This system might be connected to a different device.

Disconnect the other device and try pairing the device

again.

The device is connected but audio cannot be heard

through the system.

• For some built-in Bluetooth

devices, you have to set the

audio output to “SC-HC29” manually. Read the operating

instructions of the device for details.

Sound from the device is interrupted.

• The device is out of the 10 m communication range.

Move the device nearer to the system.

• Remove any obstacle between the system and the device.

• Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.) are

interfering. Move the device nearer to the system and

distance it from the other devices.

• Select “MODE 1” for stable communication.

The one-touch connection (NFC) is not working.

• Make sure the system and the NFC feature of the device

are switched on.

• Touch and hold the device on the NFC touch area of this

system again.

Playback image and sound are not synchronised.

• Restart the playback app of the device.

• Connect the device to the system with an audio cable

(not supplied).

█ Radio

Sound is distorted.

• Use an optional outdoor antenna. The antenna should be

installed by a competent technician.

A beat sound is heard.

• Switch off the TV or move it away from the system.

• Move mobile telephones away from the system if the

interference is apparent.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 13 Friday, April 18, 2014 9:46 AM

RQT9874

█ Main unit displays

“--:--”

• You connected the AC mains lead for the first time or there

was a power failure recently. Set the clock.

“ADJUST CLOCK”

• The clock is not set. Adjust the clock.

“ADJUST TIMER”

• The play timer is not set. Adjust the play timer.

“AUTO OFF”

• The system has not been used for 20 minutes and will

switch off within a minute. To cancel, press any button.

“ERROR”

• An incorrect operation was done. Read the instructions and

try again.

“F61”

“F77”

• Disconnect the AC mains lead and consult your dealer.

“F70”

• Examine the Bluetooth

device.

• Disconnect the Bluetooth

device. Switch off the system

and then switch on again.

“F76”

• There is a problem with the power supply.

• Disconnect the AC mains lead and consult your dealer.

“ILLEGAL OPEN”

• The sliding door is not in a correct position. Switch off the

system and then switch on again.

“NODEVICE”

• The USB device is not connected. Examine the connection.

“NO DISC”

• You have not put in a disc.

“NO PLAY”

• Examine the content. You can only play supported format.

• The system may have a problem. Switch off the system and

then switch on again.

“PLAYERROR”

•

You played an unsupported MP3 file. The system will skip

that track and play the next one.

“REMOTE 1”

“REMOTE 2”

• The remote control and the main unit are using different

codes. Change the code of the remote control.

SC-HC29

– When “REMOTE 1” is shown, press and hold [OK] and

[ ] for a minimum of 4 seconds.

– When “REMOTE 2” is shown, press and hold [OK] and

[USB/CD] for a minimum of 4 seconds.

SC-HC19

– When “REMOTE 1” is shown, press and hold [OK] and

[RADIO] for a minimum of 4 seconds.

– When “REMOTE 2” is shown, press and hold [OK] and

[CD] for a minimum of 4 seconds.

“USB OVER CURRENT ERROR”

• The USB device is using too much power. Disconnect

the USB device, switch off the system and then switch on

again.

“VBR–”

• The system cannot show the remaining play time for

variable bit rate (VBR) tracks.

Remote control code

When other Panasonic equipment responds to the

remote control of this system, change the remote control

code for this system.

Preparation

SC-HC29

Press [USB/CD] to select “CD”.

SC-HC19

Press [CD].

█ To set the code to “REMOTE 2”

SC-HC29

1 Press and hold [SELECTOR] on the main unit and

[USB/CD] on the remote control.

“REMOTE 2” is shown.

2 Press and hold [OK] and [USB/CD] for a minimum of

4 seconds.

SC-HC19

1 Press and hold [SELECTOR] on the main unit and

[CD] on the remote control.

“REMOTE 2” is shown.

2 Press and hold [OK] and [CD] for a minimum of

4 seconds.

█ To set the code to “REMOTE 1”

SC-HC29

1 Press and hold [SELECTOR] on the main unit and

[ ] on the remote control.

“REMOTE 1” is shown.

2 Press and hold [OK] and [ ] for a minimum of

4 seconds.

SC-HC19

1 Press and hold [SELECTOR] on the main unit and

[RADIO] on the remote control.

“REMOTE 1” is shown.

2 Press and hold [OK] and [RADIO] for a minimum of

4 seconds.

System memory reset

Reset the memory when the following situations occur:

• There is no response when buttons are pressed.

• You want to clear and reset the memory contents.

1 Disconnect the AC mains lead.

2 While you press and hold [1] on the main unit,

connect the AC mains lead again.

Continue to press and hold the button until

“––––––––” is shown.

3 Release [1].

All the settings are set back to the factory preset.

It is necessary to set the memory items again.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 14 Friday, April 18, 2014 9:46 AM

RQT9874

Specifications

█ Amplifier section

RMS output power stereo mode

Front Ch (both ch driven)

10 W per channel (8 ), 1 kHz, 10% THD

Total RMS stereo mode power 20 W

█ Tuner, terminals section

Preset memory FM 30 stations

Frequency modulation (FM)

Frequency range

87.50 MHz to 108.00 MHz (50 kHz step)

Antenna terminals 75  (unbalanced)

SC-HC29

AUX input

Terminal Stereo, 3.5 mm jack

█ Disc section

Disc played (8 cm or 12 cm)

CD, CD-R/RW (CD-DA, MP3

)

Pick up

Wavelength 790 nm (CD)

NORSK

Bølgelengde 790 nm (CD)

Laserstyrke Ingen farlig stråling sendes ut

█ USB section

USB port

USB standard USB 2.0 full speed

Media file format support MP3 (*.mp3)

USB device file system FAT12, FAT16, FAT32

USB port power

SC-HC29 DC OUT 5 V, 1.5 A

SC-HC19 DC OUT 5 V, 500 mA

█ Bluetooth

section

SC-HC29

Version Bluetooth

Ver. 2.1 + EDR

Class Class 2

Supported profiles A2DP, AVRCP

Operating frequency 2.4 GHz band, FH-SS

Operation distance 10 m line of sight

█ Speaker section

Speaker unit(s)

Full range 8 cm cone type x 1 per channel

Impedance 8 

█ General

Power supply AC 220 V to 240 V, 50 Hz

Power consumption

SC-HC29 22 W

SC-HC19 14 W

Dimensions (W x H x D) 400 mm x 197 mm x 107 mm

Mass 1.9 kg

Operating temperature range 0°C to +40°C

Operating humidity range

35% to 80% RH (no condensation)

Note:

• Specifications are subject to change without notice.

Mass and dimensions are approximate.

• Total harmonic distortion is measured by the digital

spectrum analyzer.

MPEG-1 Layer 3, MPEG-2 Layer 3

Power consumption in standby mode is measured with

USB device disconnected from the unit before switching to

standby mode.

Power consumption in standby mode

0.2 W (approximate)

SC-HC29

Power consumption in standby mode

(With “BLUETOOTH STANDBY” set to “ON”)

0.3 W (approximate)

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 15 Friday, April 18, 2014 9:46 AM

RQT9874

Attaching the unit to a wall (optional)

You can use the supplied wall mount brackets to attach

this unit to the wall.

Preparation

Disconnect the antenna(s) and the AC mains lead.

Installation accessories

█ Supplied accessories

 2 Wall mount brackets

 1 Safety holder

 1 Screw

█ Additional accessories

(commercially available)

 5 Screws

 1 Screw eye

 1 Cord (with a diameter of about 1.5 mm)

Installation instructions

1 Detach the pedestal of the unit.

Put a protection layer below the unit to prevent

scratches.

Remove the screw from the bottom of the unit.

2 Measure and mark the position of the wall mount

brackets on the wall.

Make sure the space on the wall is more than

60 cm (width) by 40 cm (height).

3 Fix the wall mount brackets to the wall.

Use a level to align the wall mount brackets.

4 Fix the safety holder to the unit with the supplied

screw.

5 Attach a cord to the unit to prevent the unit from

falling.

Bend the cord twice from the tip, each at 45° and

5 mm apart for it to go through the holes.

6 Connect the antenna(s) and the AC mains lead

(Z“Making the connections”).

7 Hook the unit onto the wall mount brackets.

8 Fix the safety holder to the wall.

9 Attach the cord to the wall.

Panasonic cannot be held responsible for any property

damage and/or serious injury, including death resulting

from improper installation or incorrect handling.

CAUTION!

• The installation should be done by a competent

installation specialist.

• Keep the wall mount brackets, safety holder and

screws

out of reach of children to prevent swallowing.

• Make sure the screws, the cord and the wall can

support the weight of more than 30 kg.

Screw

Protection layer

(not supplied)

Pedestal

Wall mount bracket

Screw

(not supplied)

At least 30 mm

Screw

Cord

(not supplied)

Wall

Screw

(not supplied)

Cord (not supplied)

Screw eye (not supplied)

Wall

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 16 Friday, April 18, 2014 9:46 AM

RQT9874

Declaration of Conformity (DoC)

Hereby, “Panasonic Corporation” declares that this

product is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC.

Customers can download a copy of the original DoC to

our R&TTE products from our DoC Server:

http://www.doc.panasonic.de

Contact to Authorised Representative: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Germany

This product is intended for general consumer.

(Category 3)

Ελληνικά

∆ήλωση συμμόρφωσης (DoC)

Με την παρούσα, η “Panasonic Corporation” δηλώνει ότι

το προϊόν αυτό είναι σύμφωνο με τις βασικές απαιτήσεις

και άλλες σχετικές διατάξεις της οδηγίας 1999/5/EC.

Οι πελάτες μπορούν να κατεβάσουν ένα αντίγραφο

τουπρωτοτύπου DoC για τα R&TTE προϊόντα μας από

τον DoC server μας:

http://www.doc.panasonic.de

Στοιχεία επικοινωνίας Eξουσιοδοτημένου Aντιπροσώπου:

Panasonic Marketing Europe GmbH, Panasonic Testing

Centre, Winsbergring 15, 22525 Hamburg, Γερμανία

Αυτό το προϊόν προορίζεται για καταναλωτές. (Κατηγορία 3)

Português

Declaração de Conformidade (DoC)

Com o presente documento, a “Panasonic Corporation”

declara que este produto é conforme os requisitos

específicos e demais especificações referentes à

Directriz 1999/5/EC.

Os clientes podem baixar uma cópia da declaração de

conformidade (DoC) para nossos produtos R&TTE do

Server DoC:

http://www.doc.panasonic.de

Contacte o representante autorizado: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Alemanha

Este produto destina-se ao consumador geral. (Categoria 3)

Lietuviškai

Atitikties deklaracija (AD)

Bendrovė “Panasonic Corporation” patvirtina, kad šis

gaminys tenkina direktyvos 1999/5/EB esminius

reikalavimus ir kitas taikytinas nuostatas.

Mūsų R&TTE gaminių originalios atitikties deklaracijos

kopiją klientai gali atsisiųsti iš mūsų AD serverio:

http://www.doc.panasonic.de

Įgaliotojo atstovo adresas: “Panasonic Marketing Europe

GmbH”, Panasonic Testing Centre, Winsbergring 15,

22525 Hamburg, Vokietija.

Šis gaminys skirtas bendrajam vartojimui. (3 kategorija)

Slovensko

Izjava o skladnosti (DoC)

S pričujočo izjavo podjetje “Panasonic Corporation”

izjavlja, da so svoji izdelki skladni s poglavitnimi

zahtevami in drugimi odgovarjajočimi predpisi direktive

1999/5/ES.

Stranka lahko naloži izvod izvirnega DoC o naših izdelkih

R&TTE s strežnika DoC:

http://www.doc.panasonic.de

Pooblaščeni zastopnik: Panasonic Marketing Europe

GmbH, Panasonic Testing Centre, Winsbergring 15,

22525 Hamburg, Nemčija

Izdelek je namenjen splošni uporabi. (Razred 3)

Slovensky

Vyhlásenie o zhode (DoC)

“Panasonic Corporation” týmto prehlasuje, že tento

výrobok je v zhode so základnými požiadavkami a ďalšími

príslušnými ustanoveniami smernice 1999/5/ES.

Zákazníci si môžu stiahnuť kópiu pôvodného DoC na

naše R&TTE výrobky z nášho servera DoC:

http://www.doc.panasonic.de

Kontakt na splnomocneného zástupcu: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Nemecko

Tento produkt je určený pre všeobecného spotrebiteľa.

(Kategória 3)

Norsk

Samsvarserklæring (DoC)

“Panasonic Corporation” erklærer at utstyret er i samsvar

med de grunnleggende krav og øvrige relevante krav i

direktiv 1999/5/EF.

Kundene kan laste ned en kopi av den

originalesamsvarserklæringen (DoC) for vårt R&TTE

utstyr fra vår DoC server:

http://www.doc.panasonic.de

Kontakt vår autoriserte representant: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Tyskland

Utstyret er beregnet på den vanlige forbruker. (Klasse 3)

Eesti keel

Vastavusdeklaratsioon (DoC)

“Panasonic Corporation” kinnitab käesolevaga, et see

toode on vastavuses põhiliste nõuete ja muude direktiivi

1999/5/EÜ asjakohaste sätetega.

Kliendid saavad koopia meie R&TTE toodetele kehtiva

originaalvastavusdeklaratsiooni koopia alla laadida meie

DoC serverist:

http://www.doc.panasonic.de

Võtke ühendust volitatud esindajaga: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Germany

See toode on mõeldud tavakasutajale. (III kategooria)

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 17 Friday, April 18, 2014 9:46 AM

RQT9874

Latviski

Atbilstības deklarācija (DoC)

Kompānija “Panasonic Corporation” ar šo paziņo, ka šis

izstrādājums atbilst būtiskām prasībām un citām

saistošām Direktīvas 1999/5/EK prasībām.

Pircēji var lejupielādēt oriģinālo DoC kopiju mūsu R&TTE

izstrādājumos no mūsu DoC servera:

http://www.doc.panasonic.de

Lūdzam sazināties ar pilnvaroto parstāvi: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Germany

Šis izstrādājums ir paredzēts parastam patērētājam.

(3. kategorija)

Български

Декларация за съответствие (DoC)

“Panasonic Corporation” декларира, че този продукт

съответства на същес

твените изисквания и другите

приложими разпоредби на Директива 1999/5/EC.

Потребителите могат да свалят копие от оригиналните

DoC към нашите продуктите от типа R&TTE от

сървъра, на който се съхраняват DoC:

http://www.doc.panasonic.de

За контакт с оторизиран представител: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Германия

Този продукт е предназначен за обща употреба.

(Категория 3)

Român

Declaraţie de Conformitate (DoC)

Prin prezenta, societatea “Panasonic Corporation”

declară că produsul este conform cu cerinţele esenţiale şi

cu alt

e norme corespunzătoare Directivei 1999/5/EC.

Clienţii pot descărca o copie a DoC-ului original al

produselor noastre R&TTE de la adressa noastră DoC din

Internet:

http://www.doc.panasonic.de

Contact la Reprezentanţa autorizată: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Germania

Acest produs a fost proiectat pentru clientela generală.

(Categoria 3)

Magyar

Megfelelőségi Nyilatkozat (DoC)

Ezennel a, “Panasonic Corporation” kijelenti, hogy a jelen

termék kielégíti az 1999/5/EK Irányelv létfontosságú

követelményeit és más vonatkozó rendelkezéseit.

A vásárlók letölthetik az R&TTE termékek eredeti DoC

másolatát a DoC szerverünkről:

http://www.doc.panasonic.de

Forduljon a hivatalos márkaképviselethez: Panasonic

Marketing Europe GmbH, Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Németország

A terméket általános fogyasztóknak szánták.

(3-as kategória)

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 18 Friday, April 18, 2014 9:46 AM

RQT9874

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 19 Friday, April 18, 2014 9:46 AM

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling

systems

These symbols on the products, packaging,

and/or accompanying documents mean that

used electrical and electronic products and

batteries must not be mixed with general

household waste.

For proper treatment, recovery and recycling

of old products and used batteries, please

take them to applicable collection points in

accordance with your national legislation.

By disposing of them correctly, you will help

to save valuable resources and prevent any

potential negative effects on human health

and the environment.

For more information about collection and

recycling, please contact your local

municipality.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

Note for the battery symbol (bottom symbol):

This symbol might be used in combination

with a chemical symbol. In this case it

complies with the requirement set by the

Directive for the chemical involved.

Panasonic Corporation

Web Site: http://panasonic.net

RQT9874-1R

L1213LC1044

Manufactured by:

Importer for Europe:

Panasonic Corporation

Kadoma, Osaka, Japan

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

█ NORSK

ADVARSEL!

Produkt

• For å redusere faren for brann, elektrisk støt eller

skade på apparatet:

– Dette apparatet må ikke utsettes for regn, fuktighet,

drypp eller sprut.

– Ikke plasser objekter som er fylt med væske, som

vaser, på apparatet.

– Bruk kun anbefalt tilbehør.

– Fjern ikke deksler.

–

Dette apparatet må ikke repareres på egen hånd.

Overlat servicearbeider til kvalifisert servicepersonell.

Vekselstrømnett

• Støpselet er frakoblende enhet. Strømuttaket må

befinne seg i nærheten slik at støpselet lett kan kobles

ut fra uttaket umiddelbart.

FORSIKTIG!

Produkt

• For å redusere faren for brann, elektrisk støt eller

skade på apparatet:

– Ikke plasser apparatet i en bokhylle, et innebygget

kabinett eller et annet lukket sted. Pass på at

apparatet er godt ventilert.

– Apparatets ventilasjonsåpninger må ikke dekkes til

med aviser, duker, gardiner eller lignende.

– Plasser ikke åpen ild, slik som levende lys, oppå

apparatet.

• Dette apparatet er beregnet til bruk under moderate

klimaforhold.

• Dette apparatet anvender en laser. Betjening av

kontroller, justeringer eller andre inngrep enn de som

er beskrevet i denne bruksanvisning, kan føre til farlig

bestråling.

SC-HC29.19 EB.EC RQT9874-1R EN.fm Page 20 Friday, April 18, 2014 9:46 AM

Panasonic SC-HC19EB Manualul proprietarului

Marca: Panasonic

Model: SC-HC19EB

Categorie: Ceasuri inteligente

Tip: Manualul proprietarului

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Panasonic SC-HC19EB Owner's manual

Panasonic SC-HC19EB Manualul proprietarului

Acest manual este potrivit și pentru

Panasonic SC-HC19EB Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente