Sonicare HX9903/13 Manual de utilizare

EN: User manual

RU: Руководство пользователя

KZ: Пайдаланушы нұсқаулығы

DiamondClean

Smart

4

3

5

6

8

11

7

15

13

9

10

1

2

16

12

13

14

empty page before TOC

English 6

Čeština 26

Eesti 48

Hrvatski 69

Latviešu 91

Lietuviškai 112

Magyar 134

Polski 157

Română 181

Slovenščina 204

Slovensky 225

Srpski 247

Български 268

Русский 292

Українська 315

Қазақша 336

English

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benefit from the support that

Philips offers, register your product at

www.philips.com/welcome or via the Philips

Sonicare app.

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

- Keep the charger away from water. Do not

place or store it over or near water contained in

a bathtub, washbasin, sink etc. Do not immerse

the charger in water or any other liquid. After

cleaning, make sure the charger is completely

dry before you connect it to the mains.

Warning

- The main cord cannot be replaced. If the main

cord is damaged, discard the charger.

- Always have the charger replaced with one of

the original type in order to avoid a hazard.

- Do not use the charger outdoors or near heated

surfaces.

- If the appliance is damaged in any way (brush

head, toothbrush handle or charger), stop using

it. This appliance contains no serviceable parts.

If the appliance is damaged, contact the

Consumer Care Center in your country (see

'Warranty and support').

6

English

- This appliance can be used by children aged

from 8 years and above and by persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and if they understand the hazards involved.

Children should not play with the appliance.

Cleaning and user maintenance shall not be

made by children unless they are older than 8

and supervised.

- In order to effectively charge your Philips

Sonicare handle do not place your charger base

on a magnetic metal surface.

Caution

- Do not clean the brush head, the handle or the

charger in the dishwasher.

- If you have had oral or gum surgery in the

previous 2 months, consult your dentist before

you use the toothbrush.

- Consult your dentist if excessive bleeding

occurs after using this toothbrush or if bleeding

continues to occur after 1 week of use. Also

consult your dentist if you experience

discomfort or pain when you use the Philips

Sonicare.

- The Philips Sonicare toothbrush complies with

the safety standards for electromagnetic

devices. If you have a pacemaker or other

implanted device, contact your physician or the

device manufacturer of the implanted device

prior to use.

- If you have medical concerns, consult your

doctor before you use the Philips Sonicare.

7

English

- This appliance has only been designed for

cleaning teeth, gums and tongue. Do not use it

for any other purpose. Stop using the appliance

and contact your doctor if you experience any

discomfort or pain.

- The Philips Sonicare toothbrush is a personal

care device and is not intended for use on

multiple patients in a dental practice or

institution.

- Stop using a brush head with crushed or bent

bristles. Replace the brush head every 3 months

or sooner if signs of wear appear. Do not use

other brush heads than the ones recommended

by the manufacturer.

- If your toothpaste contains peroxide, baking

soda or bicarbonate (common in whitening

toothpastes), thoroughly clean the brush head

with soap and water after each use. This

prevents possible cracking of the plastic.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic fields.

Radio Equipment Directive

- Radio Equipment in this product operates

between 2402 – 2480 MHz

- Maximum RF power transmitted by the Radio

Equipment is +3 dBm

Your Philips Sonicare (Fig. 1)

1 Hygienic travel cap

2 Brush heads

3 Handle

4 Power on/off button

5 Intensity light

6 Mode/intensity button

8

English

7 Mode light

8 Brush head replacement reminder light

9 Battery indication

10 Light ring

11 Charging base

12 Travel case

13 Cord storage compartment

14 USB cord (integrated)

15 Charging glass

16 Brush head holder

Note: The content of the box may vary based

on the model purchased.

Brush heads

Your Philips Sonicare comes with a range of brush

heads which are designed to deliver superior

results for your oral care needs.

The number and type of brush heads might

change according to the toothbrush type you

purchased.

1 Premium Plaque Defense brush head

2 Premium Gum Care brush head

3 Premium White brush head

4 Tongue Care+ brush head (specific types only)

Smart brush head recognition

Premium Plaque Defense, Premium Gum Care,

Premium White and Tongue Care+ brush heads

are enabled with smart brush head recognition

technology.

A micro-chip inside the brush head communicates

with the toothbrush handle. So when you attach a

brush head, the handle automatically recognizes

the brush head and selects the recommended

mode and intensity level to optimize your brushing

performance.

9

English

Thanks to this feature the toothbrush also tracks

your usage and gives a personalized reminder

when you need to replace your brush head for the

best oral care results.

Brushing modes

Your power toothbrush is equipped with 5

different modes to accommodate all your oral care

needs (some models come with 4 brushing modes

only). The following modes are available:

Clean mode

Clean is a 2-minute mode, recommended to be

used with intensity level 3. It gives you a thorough

and complete clean and is recommended to be

used with the Premium Plaque Defense brush

head. In order to reach optimal results, follow the

instructions below.

2

13

64

5

1 Begin brushing the upper right teeth (segment 1)

and brush for 20 seconds, on both the outer

and inner surfaces, before you move to the

upper front teeth (segment 2). Continue doing

this for segments 3 to 6 to ensure even brushing

in all 6 segments of the mouth. You will hear a

beep after each 20-second interval, to indicate

that you should move to the next segment.

White+ mode

White+ is a 2-minute 40-seconds mode,

recommended to be used with intensity level 3

and the Premium White brush head. In order to

reach optimal results, follow the instructions

below.

10

English

2

13

64

5

1 Begin brushing the upper right teeth (segment 1)

and brush for 20 seconds before you move to

the upper front teeth (segment 2). Continue

doing this for segments 3 to 6 to ensure even

brushing in all 6 sections of the mouth.

2 After completing all 6 of these segments, the

toothbrush switches to polishing mode

automatically.

2

5

3 To polish your teeth, brush the outer surface of

your upper teeth for 20 seconds (segment 2)

and then brush the outer surface of your lower

teeth for 20 seconds (segment 5). The polishing

motion used in this part of the mode will feel

and sound different from the first two minutes

of the mode.

Gum Health mode

Gum Health is a 3-minute 20-seconds mode,

recommended to be used with intensity level 3

and the Premium Gum Care brush head. In order

to reach optimal results, follow the instructions

below:

2

13

64

5

1 Begin brushing the upper right teeth (segment 1)

and brush for 20 seconds, on both the outer

and inner surfaces, before you move to the

upper front teeth (segment 2). Continue doing

this for section 3 to 6 to ensure even brushing in

all 6 segments of the mouth.

13

64

2 Next, to take optimal care for your gums, brush

the outer and inner surfaces of your upper right

back teeth for 20 seconds (segment 1), then

brush the outer and inner surfaces of your

upper left back teeth for 20 seconds (segment

3).

11

English

Continue brushing the outer and inner surfaces

of your lower right back teeth for 20 seconds

(segment 4), followed by another 20 seconds

on the outer and inner surfaces of your lower

left back teeth (segment 6). The brushing

motion used in this part of the mode will feel

and sound different from the first two minutes

of the mode.

DeepClean+ mode

DeepClean+ mode length depends on whether or

not the handle is connected to the app. In

connected mode DeepClean+ runs for two

minutes and provides BrushPacer feedback every

20 seconds. In non-connected mode DeepClean+

runs for three minutes and provides BrushPacer

feedback every 30 seconds. In order to reach

optimal results, follow the instructions below when

brushing non-connected.

2

13

64

5

- Begin brushing in the upper right teeth

(segment 1) and brush for 30 seconds, on both

the outer and inner surfaces, before you move

to the upper front teeth (segment 2). Continue

doing this for segments 3 to 6 to ensure even

brushing in all 6 segments of the mouth.

Tongue Care mode (specific types only)

Tongue Care is a 20-second mode, recommended

to be used with intensity level 1 and the Tongue

Care+ brush head. In order to reach optimal

results, follow the instructions below:

20 sec.

1 Wet the micro bristles and brush your tongue

with a back and forth motion. Clean as far back

as comfortable.

2 Rinse your mouth and repeat the procedure

two more times.

12

English

Based on the brush head you attach, the mode will

be selected automatically. If you want to adjust

the mode or intensity manually, you can do this by

using the mode/intensity button. Press the

mode/intensity button before brushing to change

the mode, and press it while brushing to adjust the

intensity level. Your selection will be remembered

next time you attached the same brush head. If

you want to go back to the initial recommended

settings for your brush head, manually change it to

the recommended setting described above.

Note: When the Philips Sonicare is used in clinical

studies, it must be used at high intensity in the

Clean mode, in White+ mode, in GumHealth mode,

or in unconnected DeepClean+ mode to achieve

the efficacy in plaque removal, stain removal, gum

health or superiority (respectively).

Intensity settings

Your power toothbrush gives you the option to

choose between 3 different intensity levels: low,

medium and high. Based on the brush head you

attach, the intensity will be selected automatically.

If you wish to change to a different intensity, you

can do so by pressing the mode/intensity button

while brushing. For optimal results it is

recommended to use the automatically selected

intensity. The intensity cannot be changed as long

as the handle is powered off or paused.

13

English

Using your Philips Sonicare

Brushing instructions

1 Attach your desired brush head. Align the brush

head so the bristles point in the same direction

as the front of the handle.

2 Wet the bristles.

3 Apply a small amount of toothpaste on the

bristles.

4 Place the toothbrush bristles against the teeth

at a slight angle (45 degrees), pressing firmly to

make the bristles reach the gumline or slightly

beneath the gumline. A change in vibration (and

a slight change in sound) and activation of the

light ring alert you when you apply too much

pressure while brushing.

Note: Keep the center of the brush in contact

with the teeth at all times.

14

English

5 Press the power on/off button to switch on the

Philips Sonicare.

6 Apply light pressure to maximize Philips

Sonicare's effectiveness. Brush your teeth with

a small back and forth motion so the bristles

reach between the teeth. Continue this motion

throughout the brushing cycle.

Note: The bristles should flare slightly. Do not

scrub.

7 To clean the inside surfaces of the front teeth,

tilt the brush handle semi-upright and make

several vertical overlapping brushing strokes on

each tooth.

Your Philips Sonicare is safe to use on:

- Braces (brush heads wear out sooner when

used on braces).

- Dental restorations (fillings, crowns, veneers).

Features and accessories

a App

b Pressure sensor

c Brush head replacement reminder

d BrushPacer

e Easy-start

f Travel case (specific types only)

g Brush head holder (specific types only)

a. App

Your Philips Sonicare is Bluetooth enabled and

allows you to achieve superior oral health care

with the Philips Sonicare app.

15

English

Using the Philips Sonicare app will help you to

improve your oral health care habits. It gives you

real-time feedback while brushing, informs you if

you missed any spots when brushing, tracks your

brushing behavior over time and provides useful

tips and tricks for your healthiest mouth ever. In

order to fully benefit from your Philips Sonicare,

we advise you to follow these steps:

Connecting your toothbrush

1 Download the Philips Sonicare app from the

Apple App Store or Google Play Store.

2 Confirm Bluetooth is switched on on your

mobile device before you open the app. Check

the settings on your mobile device to switch on

Bluetooth.

3 Open the Sonicare app.

4 To connect the toothbrush to the app, remove

the handle from the charger and press the

mode/intensity button.

5 Follow the Sonicare app instructions displayed

on your mobile device. The app automatically

connects with the toothbrush. If the toothbrush

does not connect, follow the troubleshooting

steps provided in the app.

Note: For optimal data capture, keep your mobile

device close during brushing.

b. Pressure sensor

Your Philips Sonicare is equipped with an

advanced sensor that measures the pressure you

apply while brushing. If you apply too much

pressure, the toothbrush will provide immediate

feedback to indicate that you need to reduce the

pressure. The feedback is given in two different

ways:

16

English

1 You experience a change in vibration and

therefore brushing sensation.

2 The pressure warning light of the light ring will

light up purple.

If you receive a warning, reduce the pressure. The

light will turn off and the brushing sensation will

adjust to the original sensation.

Activating or deactivating the pressure

sensor

1 Place the handle, with a brush head attached,

in the plugged-in charger.

2 Pressure sensor is enabled by holding the

mode/intensity button and by pressing the

power button twice while on a charger. The

handle will beep twice to confirm it is enabled.

3 Pressure sensor is disabled by holding the

mode/intensity button and by pressing the

power button twice while on a charger. The

handle will beep once to confirm it is disabled.

c. Brush head replacement reminder

Your Philips Sonicare is equipped with a smart

feature that tracks the wear of your brush head.

Depending on the pressure you apply and the

amount of time used, the brush head replacement

reminder light reminds you to change your brush

head. It is important to change your brush head in

time in order to guarantee the best cleaning & care

of your teeth.

When the amber brush head replacement light

starts blinking, you should replace your brush

head.

Activating or deactivating the brush head

replacement reminder

1 Place the handle in the plugged-in charger.

17

English

2 Brush head replacement reminder is enabled

by holding the mode/intensity button and by

pressing the power button three times while on

the charger. The handle will beep twice to

confirm it is enabled.

3 Brush head replacement reminder is disabled

by holding the mode/intensity button and by

pressing the power button three times while on

the charger. The handle will beep once to

confirm it is disabled.

d. BrushPacer

2

3 1

64

5

The BrushPacer is an interval timer that has a short

beep and pause to remind you to brush the

different sections of your mouth. Depending on

the brushing mode you have selected (see

'Brushing modes'), the BrushPacer beeps at

different intervals during the brushing cycle.

e. Easy-start

The Easy-start feature gently increases the power

over the first 14 brushings to help you get used to

the brushing with the Philips Sonicare. The Easy-

start feature works in all modes other than

TongueCare+ mode. This Philips Sonicare model

comes with the Easy-start feature deactivated.

Activating or deactivating the Easy-start

feature

1 Place the handle in the plugged-in charger.

2 Easy-start is enabled by holding the

mode/intensity button and by pressing the

power button once while on the charger. The

handle will beep twice to confirm it is enabled.

18

English

3 Easy start is disabled by holding the

mode/intensity button and by pressing the

power button once while on the charger. The

handle will beep once to confirm it is disabled.

Note: Using the Easy-start feature beyond the

initial ramp-up period is not recommended and

reduces Philips Sonicare effectiveness in removing

plaque.

Note: Each of the first 14 brushings must be at least

1 minute in length to properly move through the

Easy-start ramp-up cycle.

Note: To achieve clinical efficacy, Easy-start needs

to be deactivated.

f. Travel case (specific types only)

Your Philips Sonicare comes with a travel case to

make traveling with your power toothbrush more

convenient. It is designed to accommodate the

power toothbrush handle and two brush heads.

Some models come with a USB charging travel

case which connects to your laptop via USB -this

allows you to charge your Philips Sonicare when

traveling. For information about charging your

Philips Sonicare with the travel case, see 'Battery

status and charging'.

g. Brush head holder (specific types only)

The brush head holder is designed to keep and

store your brush heads.

19

English

Battery status and charging

Charging with glass (specific types only)

1 Plug the charging base into a wall socket.

2 Place the charging glass on top of the charging

base and place the handle in the glass.

The charging indicator flashes white until your

toothbrush is fully charged.

Charging with travel case (specific types only)

1 Place the handle in the charging travel case.

2 Connect the charging travel case to a laptop, a

wall-mounted USB socket or a suitable wall

adapter. The USB cord is attached to the travel

case and stored in the cord storage

compartment.

3 The battery indication flashes white until your

toothbrush is fully charged.

Important: The wall adapter must be a safe extra

low voltage source, compatible with the electrical

ratings marked on the device.

Important: Only toothbrush models HX993W,

HX993B, HX993P, HX993S, HX993L can be

charged in the travel case. Other products and

batteries are not compatible with the travel case.

Note: It takes at least 24 hours to fully charge your

Philips Sonicare. You do not have to fully charge

your handle before first use, as the handle is pre-

charged for first use. However, it is recommended

to fully charge it after first use.

Note: This charger is designed to properly charge

only one handle at a time. This charger is not

compatible with other models of Philips Sonicare.

Note: Do not place metallic objects in the travel

case, as handle charging may be affected and may

cause the charger to overheat.

20

English

Pagina se încarcă ...

Sonicare HX9903/13 Manual de utilizare

Acest manual este potrivit și pentru

Sonicare HX9903/13 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente