Philips HQ8150/16 Manual de utilizare

HQ8150, HQ8140

ENGLISH 4

INDONESIA

15

한국어 27

BAHASA MELAYU

39

ภาษาไทย 51



61

繁體中文 72

简体中文 82

4

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Only use the powerplug supplied.

The powerplug transforms 100-240 volts to a safe

low voltage of less than 24 volts.

The powerplug contains a transformer. Do not cut

off the powerplug to replace it with another plug,

as this causes a hazardous situation.

Do not use a damaged powerplug.

If the powerplug is damaged, always have it

replaced with one of the original type in order to

avoid a hazard.

Make sure the powerplug does not get wet.

Charge and store the appliance at a temperature

between 15°C and 35°C.

Never immerse the charging stand in water nor

rinse it under the tap.

Do not recharge the shaver in a closed pouch.

Always unplug the shaver before you clean it

under the tap.

The shaver complies with the internationally

approved IEC safety regulations and can be safely

cleaned under the tap.

Be careful with hot water. Always check if the water

is not too hot, to prevent your hands from getting

burnt.

-

ENGLISH

This washable shaver is not suitable for shaving in

the shower.

Do not immerse the shaver in water.

Water may leak from the socket at the bottom

of the appliance, when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed shell inside the shaver.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

Charging

Make sure the appliance is switched off before you

start to charge it.

Charging takes approx. 1 hour.

You can also shave without charging by connecting

the shaver to the mains.

Charge indications

Charging

When the shaver is being charged, the charge

light burns green.

Battery fully charged

When the battery has been fully charged, the

top light ashes green.

-

,

ENGLISH 5

Battery running low (HQ8150 only)

When the battery is running low, the bottom

light burns red.

When you switch off the shaver, this light ashes a

few times.

Cordless shaving time

A fully charged shaver has a cordless shaving time of

up to 55 minutes.

Charging the appliance

HQ8150 only: Charge the shaver when the bottom

light burns red.

Do not recharge the shaver in a closed pouch.

1 Put the appliance plug in the shaver.

2 Put the powerplug in the wall socket.

3 Remove the powerplug from the wall socket

and pull the appliance plug out of the shaver

when the battery has been fully charged.

Charging stand

You can also charge the appliance by placing it in the

charging stand, if provided.

Place the shaver properly in the plugged-in

charging stand.

Lift the shaver from the stand without tilting it.

,

ENGLISH6

Using the appliance

Shaving

1 Switch on the shaver by pressing the on/off

button once.

The blue light ring around the on/off button goes

on to indicate that the motor is running.

2 Move the shaving heads quickly over your skin,

making both straight and circular movements.

Shaving on a dry face gives the best results.

Your skin may need 2 or 3 weeks to get

accustomed to the Philips shaving system.

3 Switch off the shaver by pressing the on/off

button once.

The blue light ring around the on/off button goes

out.

4 Clean the shaver (see chapter ‘Cleaning and

maintenance’).

5 Put the protection cap on the shaver every

time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.

1 Open the trimmer by pushing the slide

downwards.

The trimmer can be activated while the motor is

running.

,

-

,

ENGLISH 7

2 Close the trimmer (‘click’).

Cleaning and maintenance

Regular cleaning guarantees better shaving

performance.

The normal way to clean the appliance is to rinse

the shaving unit and the hair chamber with hot

water every time you have used the shaver.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

Note: Water may leak from the socket at the bottom of

the appliance when you rinse it. This is normal and not

dangerous.

Every day: shaving unit and hair chamber

1 Switch off the shaver, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Press the release button to open the shaving

unit.

3 Clean the shaving unit and the hair chamber by

rinsing them under a hot tap for some time.

ENGLISH8

Make sure you clean the inside as well as the

outside of the shaving unit.

4 Close the shaving unit and shake off excess

water.

Never dry the shaving unit with a towel or tissue,

as this may damage the shaving heads.

5 Open the shaving unit again and leave it open

to let the appliance dry completely.

You can also clean the hair chamber without water

by using the brush supplied.

Every six months: shaving heads

1 Open the shaving unit, turn the lock

anticlockwise (1) and remove the retaining

frame (2).

2 Clean the cutters and guards with the brush

supplied.

Do not clean more than one cutter and guard

at a time, since they are all matching sets. If you

accidentally mix up the cutters and guards, it

may take several weeks before optimal shaving

performance is restored.

3 Put the shaving heads back into the shaving

unit. Put the retaining frame back into the

shaving unit and turn the lock clockwise.

4 Close the shaving unit.

-

ENGLISH 9

Trimmer

Clean the trimmer every time you have used it.

1 Switch off the shaver, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Clean the trimmer with the brush supplied.

3 Lubricate the trimmer teeth with a drop of

sewing machine oil every six months.

Charging stand

You can clean the charging stand with a moist cloth.

Storage

1

Put the protection cap on the shaver to

prevent damage.

2 The appliance can be stored in the pouch

supplied.

3 The shaver can be stored in the charging stand,

if provided.

ENGLISH10

Replacement

Replace the shaving heads every two years for

optimal shaving results.

Replace damaged or worn shaving heads with HQ9

Philips shaving heads only.

Note: Do not mix up the cutters and the guards to

guarantee optimal shaving performance.

1 Switch the shaver off, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Press the release button to open the shaving

unit.

3 Turn the lock anticlockwise (1) and remove the

retaining frame (2).

4 Remove the shaving heads and place new ones

in the shaving unit. Put the retaining frame

back into the shaving unit and turn the lock

clockwise.

Make sure that the projections of the shaving

heads t exactly into the recesses.

5 Close the shaving unit.

Accessories

The following accessories are available:

HQ8500/HQ8000 powerplug.

HQ9 Philips Shaving Heads.

HQ110 Philips Shaving Head Cleaning Spray

(not available in China).

HQ8010 car cord.

-

ENGLISH 11

Environment

Do not throw away the appliance with the normal

household waste at the end of its life, but hand

it in at an ofcial collection point for recycling. By

doing this, you help to preserve the environment.

The built-in rechargeable battery contains

substances that may pollute the environment.

Always remove the battery before you discard

and hand in the appliance at an ofcial collection

point. Dispose of the battery at an ofcial

collection point for batteries. If you have trouble

removing the battery, you can also take the

appliance to a Philips service centre. The staff of

this centre will remove the battery for you and

will dispose of it in an environmentally safe way.

Disposal of the battery

Only remove the battery if it is completely empty.

1 Remove the powerplug from the wall socket

and pull the appliance plug out of the shaver.

2 Let the shaver run until it stops and undo the

two screws at the back of the shaver.

3 Undo the two screws in the hair chamber.

-

ENGLISH12

4 Undo the three screws in the power unit.

5 Bend the 4 hooks aside (1) to take out the

power unit (2).

Be careful, the hooks are very sharp.

6 Remove the power unit cover by means of a

screwdriver.

7 Remove the battery.

Be careful, the battery strips are very sharp.

Do not connect the shaver to the mains again after

the battery has been removed.

Guarantee & service

If you need information or if you have a problem,

please visit the Philips website at www.philips.com

or contact the Philips Customer Care Centre

in your country (you nd its phone number in

the worldwide guarantee leaet). If there is no

Customer Care Centre in your country, go to

your local Philips dealer or contact the Service

Department of Philips Domestic Appliances and

Personal Care BV.

ENGLISH 13

Guarantee restrictions

The shaving heads (cutters and guards) are not

covered by the terms of the international guarantee

because they are subject to wear.

Troubleshooting

1

Reduced shaving performance.

Cause 1: the shaving heads are dirty.The shaver

has not been rinsed long enough or the water

used was not hot enough.

Clean the shaver thoroughly before you continue

shaving. See chapter ‘Cleaning and maintenance’.

Cause 2: long hairs are obstructing the shaving

heads.

Clean the cutters and guards with the brush

supplied. See chapter ‘Cleaning and maintenance’,

section ‘Every six months: shaving heads’.

Cause 3: the shaving heads are damaged or worn.

Replace the shaving heads. See chapter

‘Replacement’.

2 The shaver does not work when the on/off

button is pressed.

Cause 1: the battery is empty.

Recharge the battery. See chapter ‘Charging’.

Cause 2: the appliance is not connected to the

mains.

Put the powerplug in the wall socket.

3 The shaving unit has come off the shaver.

The shaving unit has not been placed correctly.

If the shaving unit becomes detached from the

shaver, you can easily put it back by inserting the

hinge into the slot in the rim of the hair chamber

and pushing it home until it locks into place

(‘click’).

-

ENGLISH14

15

Penting

Bacalah petunjuk pengguna ini secara seksama

sebelum Anda menggunakan alat dan simpan untuk

referensi di kemudian hari.

Alat ini tidak dimaksudkan untuk digunakan oleh

orang (termasuk anak-anak) dengan cacat sik,

indera atau kecakapan mental yang kurang, atau

kurang pengalaman dan pengetahuan, kecuali jika

mereka diberikan pengawasan atau pengarahan

mengenai penggunaan alat oleh orang yang

bertanggungjawab bagi keselamatan mereka.

Anak kecil harus diawasi untuk memastikan

mereka tidak bermain-main dengan alat ini.

Gunakan hanya steker listrik yang disertakan.

Steker mengubah tegangan 100-240 volt menjadi

tegangan rendah yang aman di bawah 24 volt.

Steker listrik berisi trafo. Jangan memotong steker

listrik dan menggantinya dengan steker lain, karena

ini dapat membahayakan.

Jangan gunakan steker listrik yang rusak.

Jika steker listrik rusak, gantilah selalu dengan salah

satu tipe yang asli agar terhindar dari bahaya.

Pastikan steker listrik tidak basah.

Isi dan simpan alat pada suhu antara 15 °C dan

35 °C.

Jangan merendam dudukan pengisi baterai dalam

air maupun membersihkannya di bawah keran air.

Jangan mengisi ulang pencukur di dalam kantong

tertutup.

Selalu mencabut steker dari pencukur sebelum

membersihkannya di bawah keran.

-

INDONESIA

16

Alat cukur ini memenuhi peraturan keselamatan

IEC yang disepakati secara internasional dan dapat

dengan aman dibersihkan di bawah keran air.

Hati-hati dengan air panas. Selalu periksa apakah air

tidak terlalu panas untuk mencegah luka bakar pada

tangan Anda.

Pencukur yang dapat dicuci ini tidak sesuai untuk

mencukur di bawah pancuran.

Jangan mencelupkan pencukur ke dalam air.

Air mungkin keluar dari soket bawah alat saat

Anda membilasnya. Ini adalah normal dan tidak

berbahaya karena semua bagian elektronik

disimpan dalam wadah yang tertutup rapat di

dalam alat cukur.

Medan elektromagnet (EMF)

Alat Philips ini mematuhi semua standar yang

berkenaan dengan medan elektromagnet (EMF). Jika

ditangani sebagaimana layaknya dan sesuai dengan

petunjuk pengguna ini, alat tersebut aman digunakan

menurut bukti ilmiah yang kini tersedia.

Pengisian daya

Pastikan alat telah dimatikan sebelum mengisi

baterainya.

Waktu pengisian daya kurang lebih 1 jam.

Anda juga dapat mencukur tanpa mengisi daya

dengan menghubungkan pencukur ke listrik.

-

INDONESIA16

17INDONESIA 17

Indikator daya

Pengisian daya

Saat baterai pencukur diisi ulang, lampu pengisian

akan menyala hijau.

Baterai terisi penuh

Bila baterai sudah terisi penuh, lampu bagian atas

akan berkedip hijau.

Baterai lemah (hanya HQ8150)

Saat baterai mulai melemah, lampu bagian bawah

menyala merah.

Apabila Anda mematikan pencukur, lampu ini

berkedip beberapa kali.

Waktu pencukuran tanpa kabel

Pencukur yang terisi penuh dapat digunakan tanpa

kabel hingga 55 menit.

Mengisi baterai pencukur

Hanya HQ8150: Isi ulang baterai alat cukur apabila

lampu bagian bawah menyala merah.

Jangan mengisi ulang pencukur di dalam kantong

tertutup.

1 Pasang steker alat pada pencukur.

2 Masukkan steker listrik ke stopkontak.

3 Setelah baterai terisi penuh, cabut steker listrik

dari stopkontak dan lepaskan steker alat dari

pencukur.

Dudukan pengisian baterai

Anda juga dapat mengisi daya alat cukur dengan

memasangnya pada dudukan pengisi daya, jika

tersedia.

,

18

Letakkan alat cukur dalam dudukan pengisi

baterai plug-in.

Angkat pencukur dari dudukannya dengan arah

tegak lurus.

Menggunakan alat

Mencukur

1 Hidupkan alat cukur dengan menekan tombol

on/off sekali.

Cincin lampu biru di sekitar tombol on/off

menyala untuk menunjukkan bahwa motor

bekerja.

2 Gerakkan kepala pencukur dengan cepat pada

kulit Anda, lakukan gerakan lurus maupun

memutar.

Mencukur pada kulit yang kering memberikan hasil

terbaik.

Kulit Anda mungkin memerlukan 2 atau 3 minggu

agar terbiasa dengan sistem pencukuran Philips.

3 Matikan alat cukur dengan menekan tombol

on/off sekali.

Cincin lampu biru di sekitar tombol on/off akan

mati.

,

-

,

INDONESIA18

19INDONESIA 19

4 Bersihkan pencukur (lihat bab ‘Pembersihan

dan Perawatan’).

5 Pasang tutup pelindung pada pencukur setiap

kali Anda selesai menggunakannya, agar tidak

rusak.

Memangkas

Untuk merapikan cambang dan kumis.

1 Buka pemangkas dengan menekan sorongan ke

bawah.

Pemangkas dapat dihidupkan saat motor bekerja.

2 Tutup pemangkas (terdengar bunyi ‘klik’).

Pembersihan dan perawatan

Membersihkan secara teratur akan menjamin hasil

cukur yang lebih baik.

Cara yang normal untuk membersihkan alat adalah

dengan mencuci unit pencukur dan tempat rambut

dengan air panas setiap kali Anda selesai bercukur.

Hati-hati dengan air panas. Selalu periksa apakah air

tidak terlalu panas untuk mencegah luka bakar pada

tangan Anda.

Catatan: Air mungkin merembes keluar dari soket di

bagian bawah alat saat Anda membilasnya. Ini normal

dan tidak berbahaya.

20

Setiap hari: unit pencukur dan tempat

rambut

1 Matikan pencukur, cabut steker listrik dari

stopkontak di dinding lalu lepaskan steker alat

dari pencukur.

2 Tekan tombol pelepas untuk membuka unit

cukur.

3 Bersihkan unit pencukur dan penampung

rambut dengan membilasnya selama beberapa

saat dengan air panas dari keran.

Pastikan Anda juga membersihkan bagian dalam di

samping bagian luar unit pencukur.

4 Tutup unit pencukur dan kibaskan untuk

membuang air yang tertinggal.

Jangan sekali-kali mengeringkan unit pencukur

dengan handuk atau kertas tisu, karena dapat

merusak kepala pencukur.

5 Buka lagi unit pencukur dan biarkan terbuka

agar kering sama sekali.

Anda juga dapat membersihkan ruang rambut tanpa

air dengan menggunakan sikat yang disertakan.

-

INDONESIA20

21INDONESIA 21

Setiap enam bulan: kepala pencukur

1 Buka unit pencukur, putar kunci berlawanan

arah jarum jam (1) lalu lepaskan bingkainya (2).

2 Bersihkan pemotong dan pelindung dengan

sikat yang disertakan.

Jangan membersihkan lebih dari satu pemotong

dan pelindung sekaligus, karena keduanya

merupakan pasangan. Jika secara tidak sengaja Anda

mencampuradukkan pemotong dan pelindung, akan

dibutuhkan beberapa minggu sebelum pencukuran

dapat kembali optimal.

3 Pasang kembali kepala pencukur ke dalam unit

pencukur. Pasang kembali bingkainya ke dalam

unit pencukur lalu putar kunci searah jarum

jam.

4 Tutup unit pencukur.

Pemangkas

Bersihkan pemangkas setiap kali Anda selesai

menggunakannya.

1 Matikan pencukur, cabut steker listrik dari

stopkontak di dinding lalu lepaskan steker alat

dari pencukur.

2 Bersihkan pemangkas dengan sikat yang

disertakan.

22

3 Lumasi gigi pemangkas dengan satu tetes

minyak mesin jahit setiap enam bulan.

Dudukan pengisian baterai

Anda dapat membersihkan dudukan pengisi baterai

dengan lap basah.

Penyimpanan

1

Pasang penutup pada pencukur untuk

mencegah kerusakan.

2 Alat cukur dapat disimpan di dalam kantung

yang disediakan.

3 Pencukur dapat disimpan pada dudukan pengisi

baterai, jika tersedia.

Penggantian

Ganti kepala pencukur setiap dua tahun untuk hasil

pencukuran yang optimal.

Ganti kepala pencukur yang rusak atau aus hanya

dengan kepala pencukur HQ9 Philips.

Catatan: Jangan mencampuradukkan pemotong dan

pelindung untuk menjamin kinerja pencukuran yang

optimal.

INDONESIA22

Pagina se încarcă ...

Philips HQ8150/16 Manual de utilizare

Acest manual este potrivit și pentru

Philips HQ8150/16 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente