Samsung WF1124XAC Manual de utilizare

Washing Machine

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

WF1124ZA(C/U)

WF1124ZB(C/U)

WF1124XA(C/U)

WF1124XB(C/U)

ARNO_DC68-03165H-09_EN.indd 1ARNO_DC68-03165H-09_EN.indd 1 2015-10-21  5:47:302015-10-21  5:47:30

English - 2

contents

SAFETY INFORMATION

3

3 What you need to know about safety

instructions

3 Important safety symbols and precautions

10 Instruction about the WEEE mark

SETTING UP YOUR WASHING

MACHINE

11

11 Checking the parts

12 Meeting installation requirements

12 Electrical supply and grounding

12 Water Supply

13 Drain

13 Flooring

13 Surrounding temperature

13 Alcove or closet installation

13 Installing your washing machine

WASHING A LOAD OF LAUNDRY

19

19 Washing for the ﬁ rst time

19 Basic instructions

20 Using the control panel

23 Eco Display (selected LCD models)

23 Child Lock

23 Sound Off

24 Delay End

24 My Cycle

25 Eco Bubble

26 Washing clothes using the cycle selector

27 Washing clothes manually

27 Laundry guidelines

28 Detergent and additives information

28 Which detergent to use

29 Detergent drawer

29 Liquid Detergent (Selected models)

CLEANING AND MAINTAINING YOUR

WASHING MACHINE

30

30 Eco Drum Clean

31 Draining the washing machine in an

emergency

32 Cleaning the debris ﬁ lter

32 Cleaning the exterior

33 Cleaning the detergent drawer and drawer

recess

33 Cleaning the water hose mesh ﬁ lter

34 Repairing a frozen washing machine

34 Storing your washing machine

TROUBLESHOOTING AND

INFORMATION CODES

35

35 Check these points if your washing machine...

36 Information codes

CALIBRATING YOUR WASHING

MACHINE

37

37 Calibration mode

CYCLE CHART

38

38 Cycle chart

APPENDIX

39

39 Fabric care chart

39 Protecting the environment

40 Speciﬁ cations

41 Sheet of household washing machines

ARNO_DC68-03165H-09_EN.indd Sec3:2ARNO_DC68-03165H-09_EN.indd Sec3:2 2015-10-21  5:47:362015-10-21  5:47:36

Pagina se încarcă ...

English - 4

1. This appliance is not to be used by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety.

2. For use in Europe: This appliance can be used by

children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack

of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without

supervision.

3. Children should be supervised to ensure that they do not

play with the appliance.

4. If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualiﬁ ed

persons in order to avoid a hazard.

5. The new hose-sets supplied with the appliance are to be

used and that old hose-sets should not be reused.

6. For appliances with ventilation openings in the base, that a

carpet must not obstruct the openings.

7. For use in Europe: Children of less than 3 years should

be kept away unless continuously supervised.

safety information

ARNO_DC68-03165H-09_EN.indd Sec10:4ARNO_DC68-03165H-09_EN.indd Sec10:4 2015-10-21  5:47:362015-10-21  5:47:36

Pagina se încarcă ...

English - 11

02 SETTING UP

setting up your washing

machine

Be sure to have your installer follow these instructions closely so that your new

washing machine works properly and so that you’re not at risk of injury when doing

laundry.

CHECKING THE PARTS

Carefully unpack your washing machine, and make sure you’ve received all of the parts shown below.

If your washing machine was damaged during shipping, or if you do not have all of the parts, contact

Samsung Customer Service or your Samsung dealer.

Spanner

* Bolt hole

covers

Cold

Hot

(Selected

model)

Hose guide

Liquid

detergent box

(Selected

model)

Water supply hose

* Bolt hole covers : The number of bolt hole covers depends on the model (3~6 covers).

Detergent drawer

Control panel

Door

Levelling feet

Work top

Plug

Drain hose

Emergency drain

tube

Debris ﬁ lter

Filter Cover

Tub

Release lever

ARNO_DC68-03165H-09_EN.indd Sec4:11ARNO_DC68-03165H-09_EN.indd Sec4:11 2015-10-21  5:47:372015-10-21  5:47:37

English - 12

setting up your washing

machine

MEETING INSTALLATION REQUIREMENTS

Electrical supply and grounding

Never use an extension cord.

Use only the power cord that comes with your washing machine.

When preparing for installation, ensure that your power supply offers:

• AC 220-240 V / 50 Hz fuse or circuit breaker

• Individual branch circuit serving only your washing machine

Your washing machine must be grounded. If your washing machine malfunctions or breaks

down, grounding will reduce the risk of electric shock by providing a path of least resistance for

the electric current.

Your washing machine comes with a power cord having a three-prong grounding plug for use in

a properly installed and grounded outlet.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Improperly connecting the equipment-grounding conductor can result in electric shock.

Check with a qualiﬁ ed electrician or serviceman if you are unsure if the washing machine is

properly grounded. Do not modify the plug provided with the washing machine. If it does not ﬁ t

the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

Water Supply

Your washing machine will ﬁ ll properly when your water pressure is 50 kPa ~ 800 kPa. Water

pressure less than 50 kPa may cause water valve failure, not allowing the water valve to shut

off completely. Or, it may take the washing machine longer to ﬁ ll than what the controls allow,

resulting in your washing machine turning off. (A ﬁ ll-time limit, designed to prevent overﬂ ows/

ﬂ ooding if an internal hose becomes loose, is built into the controls.)

The water taps must be within 120cm of the back of your washing machine for the provided inlet

hoses provided to reach your washing machine.

Most plumbing supply stores sell inlet hoses of various lengths up to 305 cm long.

You can reduce the risk of leaks and water damage by:

• Making water taps easily accessible.

• Turning off taps when the washing machine is not in use.

• Periodically checking for leaks at water inlet hose ﬁ ttings.

Before using your washing machine for the ﬁ rst time, check all connections at the water

valve and taps for leaks.

WARNING

ARNO_DC68-03165H-09_EN.indd Sec4:12ARNO_DC68-03165H-09_EN.indd Sec4:12 2015-10-21  5:47:372015-10-21  5:47:37

Pagina se încarcă ...

English - 14

STEP 2

Removing the shipping bolts

Before installing the washing machine, you must remove all shipping bolts from the back of the

unit.

1. Loosen all the bolts with the supplied wrench.

2. Hold the bolt with the spanner and pull it through the wide

section of the hole. Repeat for each bolt.

3. Fill the holes with the supplied plastic covers.

4. Store the shipping bolts away safely in case you have to move the washing machine in the

future.

Packaging materials can be dangerous to children; keep all packaging material (plastic

bags, polystyrene, etc.) well out of the reach of children.

setting up your washing

machine

WARNING

Option

ARNO_DC68-03165H-09_EN.indd Sec4:14ARNO_DC68-03165H-09_EN.indd Sec4:14 2015-10-21  5:47:372015-10-21  5:47:37

Pagina se încarcă ...

English - 16

setting up your washing

machine

Connecting the water supply hose

1. Remove the adaptor from the water supply hose.

2. First, using a ‘+’ type screwdriver, loosen the four screws

on the adaptor. Next, take the adaptor and turn part (2)

following the arrow until there is a 5 mm gap.

3. Connect the adaptor to the water tap by tightening the

screws ﬁ rmly while lifting the adaptor upwards.

Turn part (2) following the arrow and connect (1) and (2).

4. Connect the water supply hose to the adaptor.

When you release part (3), the hose automatically

connects to the adaptor making a ‘click’ sound.

After you have connected the water supply

hose to the adaptor, ensure that it is connected

correctly by pulling the water supply hose

downwards.

5. Connect the other end of the water supply hose to the inlet

water valve at the rear of the washing machine. Screw the

hose clockwise all the way in.

Adaptor

Water supply

hose

1

2

5 mm

1

2

Water tap

Option

3

ARNO_DC68-03165H-09_EN.indd Sec4:16ARNO_DC68-03165H-09_EN.indd Sec4:16 2015-10-21  5:47:382015-10-21  5:47:38

English - 17

02 SETTING UP

6. Turn on the water supply and ensure that no water leaks

from the water valve, tap or adaptor. If there is a water

leaks, repeat the previous steps.

Do not use your washing machine if there is a water leak.

This may cause electric shock or injury.

• If the water tap has a screw type tap, connect the water

supply hose to the tap as shown.

Use the most conventional type of tap for the water supply. In case the tap is square or too

big, remove the spacing ring before inserting the tap into the adaptor.

Connecting the Aqua Hose (Selected models)

The Aqua Hose was invented for perfect leakage protection.

It is attached to the water supply hose and automatically cuts

off the water ﬂ ow if the hose is damaged. It also displays a

warning indicator.

• Connect the water supply hose to the tap as shown.

✗

WARNING

ARNO_DC68-03165H-09_EN.indd Sec4:17ARNO_DC68-03165H-09_EN.indd Sec4:17 2015-10-21  5:47:382015-10-21  5:47:38

English - 18

setting up your washing

machine

Connecting the drain hose

The end of the drain hose can be positioned in three ways:

1. Over the edge of a wash basin: The drain hose must be placed at a height of between 60

and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure

the guide to the wall with a hook or to the tap with a piece of string to prevent the drain hose

from moving.

2. ln a sink drain pipe branch: The drain pipe branch must be above the sink siphon so that

the end of the hose is at least 60 cm above the ground.

3. ln a drain pipe: We recommend using a 65 cm high vertical pipe; it must be no shorter than

60 cm and no longer than 90 cm.

The standpipe drain requires;

• minimum diameter 5 cm.

• minimum carry-away capacity 60 liter per minute.

STEP 5

Powering your washing machine

Plug the power cord into a wall sockets, an AC 220-240V / 50Hz approved electrical outlet protected by a

fuse or circuit breaker. (For more information on electrical and grounding requirements, see page 14.)

Test run

Make sure that you install your washing machine correctly by running the Rinse+Spin cycle after the

installation is complete.

STEP 6

Select the Language (selected LCD models)

At the beginning setting (After power on), the “Language setting” message

appears on the display. you can select one language among English,

French, Dutch, German, Italian, or Spanish.(Polish, Russian, Turkish,

Chinese or Thai.)

* Language selections can be changed according to derived models.

1. Push the Rinse button to choose a language.

2. Push the Spin button to set the chosen language.

To reselect the language, press the Rinse and Spin buttons

simultaneously for 3 seconds.

The LCD display Language may differ depending on the model.

Drain hose

Hose guide

60 ~ 90 cm

Türkçe

Polska

Poccию

ᳯᐴ

ARNO_DC68-03165H-09_EN.indd Sec4:18ARNO_DC68-03165H-09_EN.indd Sec4:18 2015-10-21  5:47:382015-10-21  5:47:38

Pagina se încarcă ...

English - 20

USING THE CONTROL PANEL

2 7

8 9 1110 121 136

5

4

3

2 7

8 9 1110 12

1

136

5

4

3

Cycle Selector

Select the tumble pattern and spin speed for the cycle.

For detailed information, refer to “Washing clothes using the cycle

selector”. (see page 28)

Cotton - For average or lightly soiled cottons, bed linen, table linen,

underwear, towels, shirts, etc.

Synthetics - For averagely or lightly soiled blouses, shirts, etc., made

of polyester (diolen, trevira), polyamide (perlon, nylon) or other similar

blends.

Denim - A higher water level in the main wash and extra rinse ensure

that no washing powder remains that may mark your clothing.

Bedding - For bed spread, bed sheet, Bedding cover etc.

Wash under 2.5kg and only 1 kind of Bedding to achieve the best

result.

Dark Garment - Additional rinses and reduced spinning ensure that your

favourite dark clothes are washed gently and rinsed thoroughly.

Daily Wash - Use for everyday items such as underwear and shirts.

Eco Drum Clean - Use for drum cleaning. It cleanses dirt and bacteria

of drum. Regular use (after every 40 washes) is recommended. No

detergent or bleach needed.

Super Eco Wash - Low temperature Eco Bubble ensures that you

achieve perfect wash results while allowing effective energy saving.

Outdoor Care - Use for outdoor wear such as mountain clothes,

skiwear, and sports wear. Fabrics include functional technology ﬁ nishes

and ﬁ bers such as spandex, stretch, and micro-ﬁ ber.

Baby Care - High temperature wash and extra rinses ensure that no

washing powder remains to mark your thin clothes.

washing a load of laundry

1

ARNO_DC68-03165H-09_EN.indd Sec5:20ARNO_DC68-03165H-09_EN.indd Sec5:20 2015-10-21  5:47:392015-10-21  5:47:39

Pagina se încarcă ...

English - 23

03 WASHING A LOAD OF LAUNDRY

Eco Display (selected LCD models)

This function decreases the brightness of the LCD backlight if you do not use the Cycle Selector

or press any of the buttons for the pre-determined period of time.

Operating Mechanism

If you press the Start/Pause button, the Eco Display function automatically runs after 1 minute.

If you use the Cycle Selector or press any button, the Eco Display function is cancelled.

The Eco Display function will start automatically unless you use the Cycle Selector or press the

button within 1 minute.

Unless the Start/Pause button is pressed, the Eco Display function is not activated.

Child Lock

The Child Lock function allows you to lock the buttons so that the wash cycle you’ve chosen

can’t be changed.

Activating/Deactivating

If you want to activate or deactivate the Child Lock function, press the Temp and Rinse buttons

at the same time for 3 seconds. “Child Lock ” will be lit when this feature is activated.

When the Child Lock function is activated, only the Power button works. The Child Lock

function remains on even after the power is turned on and off or after the disconnecting and

reconnecting the power cord.

Sound Off

The Sound Off function can be selected during all courses. When this function is selected, sound is

turned off for all courses. Even if the power is turned on and off repeatedly, the setting is retained.

Activating/Deactivating

If you want to activate or deactivate the Sound Off function, press the Spin and Option buttons

at the same time for 3 seconds. The “Sound Off ” will be lit when this feature is activated.

3 sec. 3 sec.

ARNO_DC68-03165H-09_EN.indd Sec5:23ARNO_DC68-03165H-09_EN.indd Sec5:23 2015-10-21  5:47:402015-10-21  5:47:40

Pagina se încarcă ...

English - 25

03 WASHING A LOAD OF LAUNDRY

Eco Bubble

Eco Bubble allows detergent to distribute evenly and penetrate fabrics faster and deeper.

The bubble function is available in all courses except for Eco Drum Clean course and the

function availability is as follows.

Course Bubble function Canceling the bubble function

Cotton, Synthetics, Denim, Bedding,

Dark Garment, Daily Wash

Available

Super Eco Wash, Outdoor Care,

Baby Care, Wool, Hand Wash

Not available

Eco Drum Clean Not available -

• A different bubble function may be applied depending the course.

Eco Bubble selection is default. Press it once to deselect bubble option, press it again to

select bubble option.

1. Open the door, place the laundry inside the wash tub and close the door.

2. Press the Power button.

3. Select a function.

4. Place the appropriate amount of detergent and fabric

softener into the corresponding compartments depending

on the amount of laundry and close the detergent drawer.

• Add the appropriate amount of detergent into the

detergent compartment

, and add the fabric softener

to softener compartment just under the ﬁ ber softener

base line (MAX) of “A”).

• When the Prewash course is selected, add detergent

into the prewash compartment as well.

• To use liquid detergent, leave the liquid detergent box in the drawer(refer to “Liquid

Detergent” section on page 31).

Do not add powdered detergent into the liquid detergent box.

5. Press the Start/Pause button.

• Press the Start/Pause button to start the wash.

• The amount of the laundry is automatically detected and the laundry is washed.

• Once a washing machine operation begins, you cannot add or select the bubble function.

• Enough bubbles are generated with the speciﬁ ed amount of detergent.

• Please clean the Debris ﬁ lter frequently. Periodic cleaning helps generate sufﬁ cient

bubbles.

• Depending on the detergent and the laundry, the bubbles may be absorbed and seem

like a small quantity.

• Although bubbles are generated once the wash begins, it may take several minutes for

users to see them.

ARNO_DC68-03165H-09_EN.indd Sec5:25ARNO_DC68-03165H-09_EN.indd Sec5:25 2015-10-21  5:47:412015-10-21  5:47:41

Pagina se încarcă ...

English - 28

Determining the load capacity

Do not overload the washing machine or your laundry may not wash properly. Use the chart

below to determine the load capacity for the type of laundry you are washing.

Fabric Type Load Capacity

Model

WF1124

Cotton

- average/lightly soiled

- heavily soiled

12.0 kg

Synthetics 5.0 kg

Denim 3.0 kg

Bedding 2.5 kg

Outdoor Care 2.0 kg

Wool 2.0 kg

• When the laundry is unbalanced (“UE” lights up on the display), redistribute the load.

If the laundry is unbalanced, the spin efﬁ ciency may be degraded.

• When washing Bedding or Bedding cover, the wash time may be lengthened or the spin

efﬁ ciency may be degraded.

• For Bedding or Bedding cover, the recommended load capacity is 2.5 kg or less.

Make sure to insert brassieres (water washable) into a laundry net (to be

purchased additionally).

• The metal parts of the brassieres may break through the material

and damage the laundry. Therefore make sure to place them inside

a ﬁ ne laundry net.

• Small, light clothing such as socks, gloves, stockings and

handkerchiefs may become caught around the door. Place them

inside a ﬁ ne laundry net.

Do not wash the laundry net by itself without other laundry. This may cause abnormal

vibrations that could move the washing machine and cause an accident resulting in

injury.

DETERGENT AND ADDITIVES INFORMATION

Which detergent to use

The type of detergent you should use is based on the type of fabric (cotton, synthetic, delicate

items, wool), colour, wash temperature, and degree of soiling. Always use “low suds” laundry

detergent, which is designed for automatic washing machines.

Follow the detergent manufacturer’s recommendations based on the weight of the laundry, the

degree of soiling, and the hardness of the water in your area. If you do not know how hard your

water is, enquire at your local water authority.

Do not use detergent that has hardended or solidiﬁ ed as the detergent may remain in

the rinse cycle. It may cause your washing machine to not rinse properly or result in the

overﬂ ow becoming blocked.

washing a load of laundry

CAUTION

ARNO_DC68-03165H-09_EN.indd Sec5:28ARNO_DC68-03165H-09_EN.indd Sec5:28 2015-10-21  5:47:412015-10-21  5:47:41

Pagina se încarcă ...

English - 31

04 CLEANING AND MAINTAINING

The ECO Drum Clean Auto Alarm Function

• If the “ECO Drum Clean” indicator on the display and the

lamp on the Cycle Selector are lit after a wash, it indicates

that tub (drum) cleaning is required. In this case, remove

the laundry from the washing machine, turn the power

on, and clean the drum by performing the ECO Drum

Clean course.

• If you do not perform the ECO Drum Clean course, the

“ECO Drum Clean” indicator on the display and the lamp

on the Cycle Selector are turned off. However, the “ECO

Drum Clean” indicator on the display and the lamp on the

Cycle Selector are turned on again after two washes are

performed. However, this will not result in a problem with

the washing machine.

• Although generally, the ECO Drum Clean Auto Alarm

appears once a month or so, the frequency may differ

depending on the number of times the washing machine

is used.

• In case of the alarm, please also clean the debris

ﬁ lter (refer to “Cleaning the debris ﬁ lter” section on

page 34). Otherwise the performance of the bubble

function may lower down.

DRAINING THE WASHING MACHINE IN AN EMERGENCY

If there is a power outage, drain all remaining water before removing your laundry.

1. Unplug the washing machine from the power supply.

2. Open the ﬁ lter cover by using a coin or key.

3. Open the emergency drain cap by pulling it.

4. Hold the cap on the end of the emergency drain tube and

slowly pull it out.

5. Allow all the water to ﬂ ow into a bowl.

Remain water maybe more than you expected.

Prepare larger bowl.

6. Reinsert the emergency drain cap and the drain tube.

7. Replace the ﬁ lter-cover.

Filter cover

Emergency

drain tube

Emergency

drain cap

ARNO_DC68-03165H-09_EN.indd Sec6:31ARNO_DC68-03165H-09_EN.indd Sec6:31 2015-10-21  5:47:422015-10-21  5:47:42

English - 32

CLEANING THE DEBRIS FILTER

We recommend cleaning the debris ﬁ lter 5 or 6 times a year, or when the error message of “5E” is

displayed. (Refer to “Draining the washing machine in an emergency” in the previous section.)

If foreign substances accumulate debris ﬁ lter, the performance of the bubble function will be degraded.

Before cleaning the debris ﬁ lter, make sure to unplug the power cord.

1. Remove the remaining water ﬁ rst (refer to “Draining the

washing machine in an emergency” on page 33.)

If you separate the ﬁ lter without draining the remaining

water, the remaining water may trickle out.

2. Open the ﬁ lter cover by using a key or coin.

3. Unscrew the emergency drain cap by turning it to the left

and drain off all the water.

4. Unscrew the debris ﬁ lter cap.

5. Wash any dirt or other material from the debris ﬁ lter. Make

sure the drain pump propeller behind the debris ﬁ lter is not

blocked.

6. Replace the debris ﬁ lter cap.

7. Replace the ﬁ lter cover.

Do not open the debris ﬁ lter cap while the machine is running or hot

water may ﬂ ow out.

• Make sure to replace the ﬁ lter cap after the ﬁ lter cleaning. If the ﬁ lter is out of the machine, your

washing machine may malfunction or leak water.

• The ﬁ lter should be fully assembled after the ﬁ lter cleaning.

For models with the safety ﬁ lter cap

• To open, push in, and then turn the safety ﬁ lter cap counterclockwise.

The spring in the cap will make opening the cap easy.

• To close, turn the safety ﬁ lter cap clockwise. As you turn the cap, the

spring will make a rattling sound. The rattling sound is normal.

CLEANING THE EXTERIOR

1. Wipe the washing machine surfaces, including the control panel, with a soft cloth using a

nonabrasive household detergent.

2. Use a soft cloth to dry the surfaces.

3. Do not pour water onto the washing machine.

cleaning and maintaining your

washing machine

Debris ﬁ lter cap

CAUTION

ARNO_DC68-03165H-09_EN.indd Sec6:32ARNO_DC68-03165H-09_EN.indd Sec6:32 2015-10-21  5:47:422015-10-21  5:47:42

English - 33

04 CLEANING AND MAINTAINING

CLEANING THE DETERGENT DRAWER AND DRAWER RECESS

1. Press the release lever on the inside of the

detergent drawer and pull the drawer out.

2. Remove the softener divider and the liquid

detergent box(option) from the detergent

drawer.

3. Wash all parts under running water.

4. Clean the drawer recess with an old toothbrush.

5. Replace the softener divider and the liquid detergent box

(option) by pushing it ﬁ rmly into the drawer.

6. Push the drawer back into place.

7. To remove any remaining detergent, perform a rinse cycle

without any laundry in the drum.

CLEANING THE WATER HOSE MESH FILTER

You should clean the water hose mesh ﬁ lter at least once a year, or when the error message of “4E” is

displayed:

1. Turn off the water supply to the washing machine.

2. Unscrew the hose from the back of the washing machine. To prevent water from gushing out

due to the air pressure in the hose, cover the hose with a cloth.

3. Gently pull out the mesh ﬁ lter from the end of the hose using a pair of pliers and rinse it under

water until clean. Also clean inside and outside the threaded connector.

4. Push the ﬁ lter back into place.

5. Screw the hose back onto the washing machine.

6. Make sure the connections are watertight and turn on the tap.

Release lever

Softener divider

liquid detergent box (Option)

ARNO_DC68-03165H-09_EN.indd Sec6:33ARNO_DC68-03165H-09_EN.indd Sec6:33 2015-10-21  5:47:432015-10-21  5:47:43

English - 34

cleaning and maintaining your

washing machine

REPAIRING A FROZEN WASHING MACHINE

If the temperature drops below freezing and your washing machine is frozen:

1. Unplug the washing machine.

2. Pour warm water over the tap to loosen the water supply hose.

3. Remove the water supply hose and soak it in warm water.

4. Pour warm water into the washing machine drum and let it sit for 10 minutes.

5. Reconnect the water supply hose to the water tap and check if the water supply and drain

are operating normal.

STORING YOUR WASHING MACHINE

If you need to store your washing machine for an extended time, it’s better to drain and disconnect it.

Washing machines can be damaged if water is left in the hoses and internal components before storage.

1. Select the Cotton cycle and push the Quick Wash button and run your washing machine

through the cycle without a load.

2. Turn the water taps off and disconnect the inlet hoses.

3. Unplug your washing machine from the electrical outlet, and leave your washing machine

door open to allow air to circulate inside the tumbler.

If your washing machine has been stored in below-freezing temperatures, allow time for any

leftover water in your washing machine to thaw out before using it.

ARNO_DC68-03165H-09_EN.indd Sec6:34ARNO_DC68-03165H-09_EN.indd Sec6:34 2015-10-21  5:47:432015-10-21  5:47:43

English - 35

05 TROUBLESHOOTING

troubleshooting and

information codes

CHECK THESE POINTS IF YOUR WASHING MACHINE...

PROBLEM SOLUTION

Will not start • Make sure your washing machine is plugged in.

• Make sure the door is ﬁ rmly closed.

• Make sure the water source tap(s) are turned on.

• Make sure to press the Start/Pause button.

Has no water or not enough

water

• Turn the water tap on fully.

• Make sure the water source hose is not frozen.

• Straighten the water intake hoses.

• Clean the ﬁ lter on the water intake hose.

Has detergent remaining in

the detergent drawer after

the wash cycle is complete

• Make sure your washing machine is running with sufﬁ cient water

pressure.

• Make sure the detergent is added to the center of the detergent

drawer.

Vibrates or is too noisy • Make sure your washing machine is on a level surface. If the surface

is not level, adjust the washing machine feet to level the appliance.

• Make sure that the shipping bolts are removed.

• Make sure your washing machine is not touching any other object.

• Make sure the laundry load is balanced.

The washing machine does

not drain and/or spin

• Straighten the drain hose. Eliminate kinked hoses.

• Make sure the debris ﬁ lter is not clogged.

Door is locked shut or will

not open.

• The door will not open until 3 minutes after the machine stops or the

power turns off.

If the problem persists, contact your local Samsung Customer Service.

ARNO_DC68-03165H-09_EN.indd Sec11:35ARNO_DC68-03165H-09_EN.indd Sec11:35 2015-10-21  5:47:432015-10-21  5:47:43

English - 36

INFORMATION CODES

If your washing machine malfunctions, you may see an information code on the display. If this happens,

please check the table below and try the suggested solution before calling Customer Service.

CODE SYMBOL SOLUTION

dE

• Make sure the door is ﬁ rmly closed.

• Make sure that laundry is not caught in the door.

4E

• Make sure the source water tap is turned on.

• Check the water pressure.

• Clean the mesh ﬁ lters of water hose.

5E

• Clean the debris ﬁ lter.

• Make sure the drainage hose is installed correctly.

• Clean the water hose mesh ﬁ lter.

UE

• The laundry load is unbalanced. Redistribute the load. If only one item

of clothing needs washing, such as a bathrobe or pair of jeans, the

ﬁ nal spin result might be unsatisfactory and an “UE” error message

will be shown in the display window.

cE/3E/Uc

• Call the after-sales service.

For any codes not listed above, or if the suggested solution doesn’t ﬁ x the problem, call your Samsung

Service Centre or local Samsung dealer.

troubleshooting and

information codes

ARNO_DC68-03165H-09_EN.indd Sec11:36ARNO_DC68-03165H-09_EN.indd Sec11:36 2015-10-21  5:47:432015-10-21  5:47:43

English - 37

06 CALIBRATING YOUR WASHING MACHINE

calibrating your washing

machine

CALIBRATION MODE

Samsung washing machine detects the laundry weight automatically. For more accurate weight detection,

please run Calibration Mode after the installation. Calibration mode is done by following the steps below.

1. Remove laundry or any contents in the machine and turn off the machine.

2. Press the Temp button and Delay End button simultaneously, and press the Power button in addition.

Then the machine turns on.

3. Press the Start button to activate “Calibration Mode”.

4. The drum rotates clockwise and counterclockwise approximately for 3 minutes.

5. When “Calibration Mode” is ﬁ nished, “End/Cycle is complete” appears on the display, and the machine

automatically turns off. The washing machine is now ready for use.

ARNO_DC68-03165H-09_EN.indd Sec8:37ARNO_DC68-03165H-09_EN.indd Sec8:37 2015-10-21  5:47:432015-10-21  5:47:43

Pagina se încarcă ...

Samsung WF1124XAC Manual de utilizare

Samsung WF1124XAC Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente