Yamaha RX-V365 Manualul proprietarului

RX-V365

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

G

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press

ASTANDBY/ON to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

........................................AC 110–120/220–240 V, 50/60 Hz

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by ASTANDBY/ON. In this

state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

Caution-ii En

Caution: Read this before operating your unit.

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge

for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the

product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper

use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in

the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or

http://www.yamaha-uk.com/ for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising

from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical

and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/

EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and

prevent any potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your

local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact

your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

1 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features.................................................................... 2

Supplied accessories .................................................. 2

Functional overview................................................ 3

Front panel ................................................................. 3

Front panel display..................................................... 4

Remote control........................................................... 5

Rear panel .................................................................. 6

Quick start guide..................................................... 7

L

Preparation of remote control ............................... 8

Connections .............................................................9

Placing speakers......................................................... 9

Connecting speakers .................................................. 9

Connecting video components................................. 11

Connecting other components ................................. 13

Using the VIDEO AUX jacks on the front panel .... 14

Connecting the FM and AM antennas ..................... 15

Connecting the power cable..................................... 15

Turning on and off the power .................................. 15

Optimizing the speaker setting for your listening

room (YPAO) ....................................................16

Using AUTO SETUP............................................... 16

Playback................................................................. 18

Basic procedure........................................................ 18

Additional operations............................................... 19

Selecting the SCENE templates ...........................22

Selecting the desired SCENE template.................... 22

Creating your original SCENE templates ................ 24

Sound field programs ...........................................25

Selecting sound field programs................................ 25

FM/AM tuning ......................................................27

Overview.................................................................. 27

FM/AM tuning operations ....................................... 27

Preset FM/AM stations ............................................ 27

Radio Data System tuning (Europe and Russia

models only).......................................................29

Displaying the Radio Data System information ...... 29

Selecting the Radio Data System program type (PTY

SEEK mode) ........................................................ 29

Using the enhanced other networks (EON) data

service.................................................................. 30

Set menu ................................................................ 31

Using set menu......................................................... 32

1 SOUND MENU .................................................... 32

2 INPUT MENU ...................................................... 34

3 OPTION MENU ................................................... 35

Advanced setup..................................................... 37

Troubleshooting.................................................... 38

Glossary ................................................................. 43

Specifications......................................................... 44

Index ...................................................................... 45

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the

front panel or the ones on the remote control. In case the button

names differ between the front panel and the remote control, the

button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications

are subject to change in part as a result of improvements, etc. In case

of differences between the manual and product, the product has

priority.

• “ASTANDBY/ON” or “eDVD” (example) indicates the name of

the parts on the front panel or the remote control. Refer to the

“Functional overview” on page 3.

2 En

INTRODUCTION

Built-in 5-channel power amplifier

◆ Minimum RMS output power

(1 kHz, 0.9% THD, 6 Ω)

Front: 100 W/ch

Center: 100 W

Surround: 100 W/ch

Various input/output connectors

◆ HDMI (IN x 2, OUT x 1), Component video (IN x 3, OUT x

1), Composite video (IN x 3, OUT x 2), Coaxial digital audio

(IN x 1), Optical digital audio (IN x 2), Analog audio (IN x 9,

OUT x 2)

◆ Speaker out (5-channel), Subwoofer out

◆ Discrete multi-channel input (6-channel)

SCENE select function

◆ Preset SCENE templates for various situations

◆ SCENE template customizing capability

Sound field programs

◆ Proprietary Yamaha technology for the creation of surround

field

◆ Compressed Music Enhancer mode

◆ SILENT CINEMA™

Decoders and DSP circuits

◆ Dolby Digital decoder

◆ Dolby Pro Logic/Dolby Pro Logic II decoder

◆ DTS decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA™

Sophisticated FM/AM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or high-definition

video (includes 1080p video signal transmission)

Other features

◆ 192-kHz/24-bit D/A converter

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control capability

Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic,” and the double-D symbol are

trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,487,535 and

other U.S. and worldwide patents issued and pending.

DTS is a registered trademark and the DTS logos and

“HDMI,” the “HDMI” logo and “High-Definition

Multimedia Interface” are trademarks, or registered

trademarks of HDMI Licensing LLC.

“SILENT CINEMA” is a trademark of Yamaha

Corporation.

Check that you received all of the following parts.

❏ Remote control

❏ Batteries (2) (AAA, R03, UM-4)

❏ AM loop antenna

❏ Indoor FM antenna

❏ Optimizer microphone

Features

Supplied accessories

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

A STANDBY/ON

Turns on this unit, or sets it to standby mode (see page 15).

B PHONES jack

Connect to a pair of headphones (see page 20).

C SPEAKERS

Turns on or off the set of front speakers connected to the

FRONT A or FRONT B speaker terminals (see page 19).

D EDIT PRESET/TUNING

Switches the tuning mode (see page 27).

E A/B/C/D/E

Selects the preset station group (A to E) (see page 28).

F PRESET/TUNING l / h

Tunes into radio stations manually or automatically and selects a

preset station group (see page 27).

G BAND

Selects the reception band from FM and AM (see page 27).

H MEMORY

Stores a station that you tuned into as a preset station (see

page 27).

I TUNING AUTO/MAN’L

Selects a tuning method from automatic or manual tuning (see

page 27).

J SCENE 1/2/3/4

Recalls an input source and a sound field program assigned to

each SCENE button (see page 22).

K TONE CONTROL

Selects “BASS” and “TREBLE” to adjust frequency response

(see page 20).

L PROGRAM l / h

Selects a sound field program (see page 25).

M STRAIGHT

Activates the “STRAIGHT” mode (see page 26).

N INPUT l / h

Selects an input source (see page 18).

O NIGHT

Selects a night listening mode (see page 20).

P VOLUME control

Adjusts the volume level of this unit (see page 18).

Q VIDEO (VIDEO AUX) jack

Connects to a game console or a video camera using a

composite video cable (see page 14).

R AUDIO L/R (VIDEO AUX) jacks

Connects to a game console or a video camera using analog

audio cables (see page 14).

S PORTABLE (VIDEO AUX) jack

Connects to an audio component (such as iPod) (see page 14).

T OPTIMIZER MIC jack

Connect to the supplied optimizer microphone (see page 16).

U Front panel display

Shows information about the operational status of this unit (see

page 18).

Functional overview

Front panel

OPTIMIZER

MIC

PHONES

SILENT

CINEMA

TONE

CONTROL

PROGRAM

STRAIGHT

INPUT

VIDEO

AUDIO

PORTABLE

VIDEO

AUX

VOLUME

EFFECT

l

h

l

h

SCENE

STANDBY

/ON

1

NIGHT

2

3

4

SPEAKERS

PRESET/TUNING

EDIT

A/B/C/D/E

PRESET/TUNING

l

h

BAND

MEMORY

TUNING

AUTO/MAN'L

A

C D G H T

K OL N

IU PE F

J Q SB RM

4 En

Functional overview

a Decoder indicator

Lights up when any of the decoders of this unit functions.

b ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is

selected (see page 25).

c VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see page 26).

d SILENT CINEMA indicator

Lights up when headphones are connected and a sound field

program is selected (see page 26).

e Input source indicators

The corresponding cursor lights up to show the currently

selected input source.

f YPAO indicator

Lights up when you run “AUTO SETUP” and when the speaker

settings set in “AUTO SETUP” are used without any

modifications (see page 16).

g Tuner indicators

Lights up when this unit is in the FM or AM tuning mode (see

page 27).

h MUTE indicator

Flashes while the MUTE function is on (see page 20).

i VOLUME level indicator

Indicates the current volume level.

j PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

k Headphones indicator

Lights up when headphones are connected (see page 20).

l SP A B indicators

Lights up according to the set of front speakers selected (see

page 18).

m NIGHT indicator

Lights up when you select a night listening mode (see page 20).

n CINEMA DSP indicator

Lights up when you select a sound filed program (see page 26).

o Multi-information display

Shows the name of the current sound field program and other

information when adjusting or changing settings.

p Radio Data System indicators (Europe and Russia

models only)

• PTY HOLD

Lights up when this unit is in the PTY SEEK mode (see

page 29).

• PS, PTY, RT and CT

Light up according to the available Radio Data System

information.

•EON

Lights up when the EON data service is available.

q SLEEP indicator

Lights up while the sleep timer is on (see page 21).

r Input channel and speaker indicators

• LFE indicator

Lights up when the input signal contains the LFE signal.

• Input channel indicators

Indicates the channel components of the current digital input

signal.

Front panel display

DVR DVD CD

V-AUX DTV/CBL

MD/CD-R

TUNER

q

PL

q

PL

ENHANCER

SILENT CINEMA

NIGHT

AUTO

YPAO

PRESET

PSHOLD RT

EON

PTYPTY

TUNED

MUTE

VOLUME

MEMORY

SLEEP

VIRTUAL

PCM

A B

SP

mS

ft

dB

LFE

LCR

SL SR

q

DIGITAL

t

dB

STEREO

CT

ab c d feghi

jklmnoqr

p

LFE

LCR

SL SR

LFE indicator

Input channel indicators

5 En

Functional overview

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a Infrared window

Outputs infrared control signals (see page 8).

b STANDBY ( )

Sets this unit to the standby mode (see page 15).

c POWER ( )

Turns this unit on (see page 15).

d SCENE 1/2/3/4

Recalls an input source and a sound field program assigned to

each SCENE button (see page 22).

e Input selector buttons

Switches the input source to each source (see page 18).

f MULTI CH IN

Sets the input source to MULTI CH IN (see page 19).

g VOLUME +/–

Adjusts the volume level of this unit (see page 18).

h MUTE

Mutes audio output. Press the button again to resume audio

output (see page 20).

i PRESET l / h

Tunes into radio stations manually or automatically and selects a

Preset station number (1 to 8) (see page 27).

j A/B/C/D/E

Selects the preset station group (A to E) (see page 28).

k MENU

Displays the set menu on the front panel display (see page 32).

l SLEEP

Sets the sleep timer (see page 21).

m LEVEL

Selects the speaker that you want to adjust (see page 20).

n AUDIO SEL

Selects an audio input select setting for each input source (see

page 19).

o Cursors (l / h / n / k) / ENTER

• Press cursors to navigate the set menu (see page 32).

• Press ENTER to confirm a selection in the set menu (see

page 32).

p NIGHT

Selects a night listening mode (see page 20).

q RETURN

Returns the previous menu level in the set menu mode (see

page 32).

r SUR.DECODE

Selects a decoder from four decoders (see page 26).

s DISPLAY

Is not available for this unit.

t STRAIGHT

Activates the “STRAIGHT” mode (see page 26).

u PROG l / h

Selects the sound field program (see page 25).

v ENHANCER

Sets the sound field program to the “Music Enh. 2ch” or “Music

Enh. 5ch” (see page 25).

w INFO/Radio data system control

Controls the Radio Data System with 4-buttons (INFO/EON/

MODE (PTY-SEEK)/START (PTY-SEEK)) (see page 29).

Remote control

STANDBY

SCENE

POWER

CD

DVD

A/B/C/D/E

PRESET

SLEEP

LEVEL

MENU

AUDIO SEL

NIGHT

RETURN

SUR.DECODE

STRAIGHT

INFO EON

PTY

MODE

PROG

ENHANCER

DISPLAY

ENTER

MUTE

DVR

V-AU X

DTV/CBL

MD/CD-R

TUNER

MULTI CH IN

1234

VOLUME

START

SEEK

a

b

d

g

k

s

p

t

h

c

f

l

n

r

v

j

m

q

e

i

u

w

o

6 En

Functional overview

a COMPONENT VIDEO jacks

Connect to Y, PB/CB and PR/CR jacks on your video components

with component video cables (see page 11).

• DVD input jacks

• DTV/CBL input jacks

• DVR input jacks

• MONITOR OUT output jacks

b HDMI terminals

Connect to HDMI output/input terminals on your external

components with HDMI cables (see page 11).

• HDMI DVD terminal

• HDMI DTV/CBL terminal

• HDMI OUT output terminal

c VIDEO jacks

Connect to video jacks on your video components with

composite video cables (see page 11).

• DVD input jack

• DTV/CBL input jack

• DVR IN jack

• DVR OUT jack

• MONITOR OUT jack

d ANTENNA terminals

Connect to the supplied FM and AM antennas (see page 15).

e SPEAKERS terminals

Connect to each speakers (see page 9).

• FRONT A L/R

• FRONT B L/R

• SURROUND L/R

• CENTER

f DIGITAL INPUT jacks

Connect to the DIGITAL output jacks on your digital audio

components with Coaxial/Optical digital audio cables.

This input jacks support PCM, Dolby Digital and DTS bitstream

(see page 11).

• COAXIAL (DVD)

• OPTICAL (DTV/CBL)

• OPTICAL (CD)

g MULTI CH INPUT jacks

Connect to the output jacks on your multi-format player or

external decoder with analog audio cables (see page 14).

• FRONT L/R jack

• SURROUND L/R jack

•CENTER jack

• SUBWOOFER jack

h AUDIO jacks

Connect to the audio output/input jacks on your components

with analog audio cables (see page 11).

• DVD L/R jack

• DTV/CBL L/R jack

• DVR IN L/R jack

• DVR OUT L/R jack

• CD L/R jack

• IN (PLAY) L/R jack

• OUT (REC) L/R jack

i SUBWOOFER OUTPUT jack

Connect to a Subwoofer with an analog audio cable (see

page 9).

j Power cable

Connect to a standard AC outlet (see page 15).

Rear panel

DIGITAL INPUT

COMPONENT VIDEO

VIDEO

AUDIO

MULTI CH INPUT

HDMI

ANTENNA

SPEAKERS

DVD

OPTICAL

DVD

SURROUND

CENTER

FRONT B

FRONT A

DVR

SURROUND

FRONT

CENTER

SUBWOOFER

DTV/CBL

DVD

DVR

FM

AM

GND

IN

OUT

DTV/CBL

DVD

DVR

CD

OUTPUT

SUB

WOOFR

IN

OUT

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL

MONITOR

OUT

MONITOR

OUT

CD

P

R

P

B

Y

DVD

COAXIAL

DTV/

CBL

OUT

UNBAL.

f g h i

d eb ca

j

7 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

The following steps describe the easiest way to operate this unit. See the related pages for details on the operation and

settings.

In these steps, you need the following items which are not

included in the package of this unit.

❏ Speakers

We recommend magnetically shielded speakers.

❏ Front speaker ..................................... x 2

At least two front speakers are required to start

playback.

❏ Center speaker ................................... x 1

❏ Surround speaker .............................. x 2

❏ Active subwoofer ................................... x 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cable ......................................... x 5

❏ Subwoofer cable ..................................... x 1

Select a monaural RCA cable.

❏ DVD player .............................................. x 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output jack.

❏ Video monitor ......................................... x 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

❏ Video cable ............................................. x 2

Select an RCA composite video cable.

❏ Digital coaxial audio cable .................... x 1

Place your speakers in the room and connect them to this

unit.

Connect your TV, DVD player or other components.

Connect the power cable and turn on this unit.

Select the component connected in the step 3 as an input

source and start playback.

Quick start guide

Step 1: Check the items

Step 2: Set up your speakers

• Placing speakers ☞P. 9

• Connecting speakers ☞P. 9

Video monitor

Front left

speaker

Center speaker

DVD player

Surround left

speaker

Surround right

speaker

Subwoofer

Front right

speaker

Step 3: Connect your components

• Connecting a TV monitor or projector ☞P. 1 2

• Connecting audio and video components ☞P. 1 3

• Connecting a multi-format player or an external

decoder ☞P. 1 4

• Using the VIDEO AUX jacks on the front panel

☞P. 1 4

• Connecting the FM and AM antennas ☞P. 1 5

Step 4: Turn on the power

• Connecting the power cable ☞P. 1 5

• Turning on and off the power ☞P. 1 5

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 1 8

• Selecting the SCENE templates ☞P. 2 2

• Adjusting the sound field programs ☞P. 2 5

8 En

PREPARATION

1 Take off the battery compartment cover.

2 Insert the four supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all of the batteries if you notice the following conditions:

– the operation range of the remote control decreases.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose of

them correctly in accordance with your local regulations.

The remote control transmits a directional infrared ray.

Be sure to aim the remote control directly at the remote

control sensor on this unit during operation.

a Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of

conditions:

– places of high humidity, such as near a bath

– places of high temperature, such as near a heater or stove

– places of extremely low temperatures

– dusty places

Preparation of remote control

Installing batteries in the remote control

1

3

2

Using the remote control

30º 30º

Approximately 6 m (20 ft)

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

The speaker layout below shows the speaker setting we

recommend. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the Yamaha Active Servo Processing Subwoofer System,

is effective not only for reinforcing bass frequencies from

any or all channels, but also for high fidelity sound

reproduction of the LFE (low-frequency effect) channel

included in Dolby Digital and DTS sources. The position

of the subwoofer is not so critical, because low bass

sounds are not highly directional. But it is better to place

the subwoofer near the front speakers. Turn it slightly

toward the center of the room to reduce wall reflections.

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, this unit cannot reproduce the input sources

accurately.

■ 5.1-channel speaker connection

Connections

Placing speakers

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

SW

Connecting speakers

Caution

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Before connecting the speakers, make sure that this

the AC power plug is disconnected from the AC wall

outlet.

• Do not let the bare speakers wires touch each other or

do not let them touch any metal part of this unit. This

could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speaker still creates interference with the monitor,

place the speakers away from the monitor.

LRLR

LR

HDMI

VIDEO

AUDIO OUTPUT

ANTENNA

SPEAKERS

B

L

D

DTV/CBL

SURROUND CENTER FRONT B

FRONT A

MONITOR

OUT

MD/

CD-R

SUB

WOOFER

OUT

(REC)

IN

(PLAY)

DVR

B

L DVR CD

IN

OUT

IN

OUT

AM

GND

FM

75

UNBAL.

a b

c

d

f

g

e

h

10 En

Connections

* You can select the front speaker set from Front speakers (A) and Front

speakers (B) by pressing CSPEAKERS repeatedly. See page 19 for

details.

■ Connect speaker cables to each speaker

Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.)

cable to the “+” (red) terminals of your speaker. Connect

the plain cable to the “–” (black) terminals.

■ Before connecting to the SPEAKERS

terminal

A speaker cord is actually a pair of insulated cables

running side by side.

Remove approximately 10 mm (3/8”) of insulation

from the end of each speaker cable and then

twist the bare wires of the cable together to

prevent short circuits.

■ Connecting to the FRONT A terminals

1 Loosen the knob.

2 Insert the bare end of the speaker wire into

the slit on the terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the FRONT B, CENTER, and

SURROUND terminals

1 Press down the tab.

2 Insert the bare end of the speaker wire into

the hole on the terminal.

3 Release the tab to secure the wire.

Speakers Jacks on this unit

a Front speaker (A) Right* FRONT A (R)

b Front speaker (A) Left* FRONT A (L)

c Surround speaker Right SURROUND (R)

d Surround speaker Left SURROUND (L)

e Center speaker CENTER

f Front speaker (B) Right* FRONT B (R)

g Front speaker (B) Left* FRONT B (L)

h Subwoofer SUBWOOFER

10 mm (3/8”)

1

2

3

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Audio jacks and cable plugs

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

COAXIAL jack

For digital audio signals transmitted via coaxial digital

audio cable.

OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

Notes

• You can use the digital jacks to input PCM, Dolby Digital, and DTS

bitstreams. All digital input jacks are compatible with digital signals with

up to 96 kHz of sampling frequency.

• This unit handles digital and analog signals independently. Thus audio

signals input at the digital jacks are not output at the analog AUDIO OUT

(REC) jack.

Video jacks and cable plugs

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

COMPONENT VIDEO jacks

For component signals, separated into the luminance (Y)

and chrominance (P

B, PR) video signals transmitted on

separate wires of component video cables.

You can play back pictures by connecting your video

monitor and video source component to this unit using

HDMI connections.

At that time, audio/video signals output from the

connected component (such as DVD player etc.) are

output to the connected video monitor only when this unit

is turned on and set to the input source (DVD or DTV/

CBL).

Furthermore, available audio/video signals depend on the

specification of the connected video monitor. Refer to the

instruction manual of each connected component.

■ HDMI jack and cable plug

y

• We recommend using an HDMI cable shorter than 5 meters (16 feet)

with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect this unit

to other DVI components.

You can record the audio signal output at the AUDIO

OUT (REC) jack by using the recording components.

Note

• Check the copyright laws in your country to record from CDs, radio, etc.

Recording of copyrighted material may infringe copyright laws.

Connecting video components

Information on jacks and cable plugs

COAXIAL

DIGITAL AUDIO

AUDIO

OPTICAL

DIGITAL AUDIO

R

L

C

O

R

L

(White) (Red) (Orange)

Left and right

analog audio

cable plugs

Coaxial

digital audio

cable plug

Optical

digital

audio cable

plug

VIDEO

COMPONENT VIDEO

Y P

B

P

R

PB

Y

P

R

V

(Yellow) (Blue) (Red)(Green)

Composite

video cable

plug

Component

video cable

plugs

Information on HDMI™

Audio signals input at the HDMI jack are not output

from any speaker terminals but output from the

connected video monitor. To enjoy the sound from

speakers connected to this unit,

– make an analog or digital connection besides the

HDMI connection (see page 13).

– mute the volume of the connected video monitor.

Using the AUDIO OUT REC jack

PR

P

B

Y

P

R

P

B

Y

COMPONENT

VIDEO

Video signal flow for MONITOR OUT

Input

Output

(MONITOR OUT)

HDMI

HDMI cable plug

12 En

Connections

Note

• If you turn off the video monitor connected to the HDMI OUT jack via a DVI connection, the connection may fail. In this case, the HDMI indicator

flashes irregularly.

Connecting a TV monitor or projector

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

LR

L

R

VIDEO

MULTI CH INPUT

DIGITAL INPUT

OUTPUT

ANTENNA

SP

E

1

2

3

DVD

COAXIAL

OPTICAL

CD

DTV/CBL

DTV/

CBL

SURROUND C

E

MONITOR

OUT

SUB

WOOFER

DVR

FRONT CENTER

SUBWOOFER

SURROUND

IN

OUT

AM

GND

FM

75

UNBAL.

HDMI

DVDOUT DTV/CBL

COMPONENT VIDEO

DVD DTV/CBL DVR

MONITOR

OUT

Y

P

R

P

B

V

P

R

P

B

Y

LR

MD/

CD-R

OUT

(REC)

IN

(PLAY)

L

R

AUDIO

DVD DTV/CBL DVR CD

IN

OUT

TV

(or projector)

Component

video in

Video

in

Audio

out

HDMI

in

Recommended connections Alternative connections

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has three types of audio jacks, two types of video jacks and HDMI jacks. You can choose the connection

method depending on the component to be connected.

■ Connecting example (connecting a DVD player)

■ Jacks used for audio and video connections

Recommended connections are indicated by (*). When connecting a recording component, you need to make additional

connections for recording (signal transmission from this unit to the recording component).

y

• You can also use the VIDEO AUX jacks (see page 14) on the front panel

to connect an additional component.

• To confirm the positions of “jacks on this unit” in the following table,

refer to “Rear panel” in “Functional overview” on page 6.

Connecting other components

Connecting audio and video components

R

L

R

L

R

COMPONENT VIDEO

HDMI

VIDEO

AUDIOMULTI CH INPUT

DIGITAL INPUT

OUTPUT

ANTENNA

1

2

3

DVD DTV/CBL DVR

DVD

COAXIAL

OPTICAL

CD

DTV/CBL

DTV/

CBL

DVDOUT DTV/CBL

S

U

MONITOR

OUT

MD/

CD-R

SUB

WOOFER

OUT

(REC)

IN

(PLAY)

DVR

DVD

FRONT CENTER

SUBWOOFER

SURROUND

DTV/CBL DVR CD

IN

OUT

IN

OUT

MONITOR

OUT

AM

GND

FM

75

UNBAL.

Y

P

R

P

B

P

R

P

B

Y

L

R

C

V

Component out

Audio out

Video out

Coaxial out

HDMI out

Recommended connections Alternative connections

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

Component Signal type Jacks on component Jacks on this unit

DVD player or Blu-ray

Disc player

Video HDMI out* HDMI (DVD)*

Component out COMPONENT VIDEO (DVD)

Video out (composite) VIDEO (DVD)

Audio Optical out* COAXIAL (DVD)*

Audio out (analog) AUDIO (DVD)

Set-top box Video HDMI out* HDMI (DTV/CBL)*

Component out COMPONENT VIDEO (DTV/CBL)

Video out (composite) VIDEO (DTV/CBL)

Audio Optical out* OPTICAL (DTV/CBL)*

Analog out (analog) AUDIO (DTV/CBL)

14 En

Connections

Notes

• Be sure to make the same type of video connections as those made for your TV if the video conversion is disabled. For example, if you connected your

TV to the VIDEO MONITOR OUT jack of this unit, connect other components to the VIDEO jacks.

• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.

• To make a digital connection to a component other than the default one assigned to each DIGITAL INPUT or DIGITAL OUTPUT jack, configure the

“INPUT ASSIGN” setting (see page 34).

• Only analog audio signals output at AUDIO OUT (REC) jack can be recorded using the recording components. Therefore Digital signals input at the

DIGITAL INPUT jacks or analog signals input at MULTI CH IN jacks can be output at the analog AUDIO OUT (REC) jack for recording.

This unit is equipped with 6 additional input jacks

(FRONT L/R, SURROUND L/R, CENTER and

SUBWOOFER) for discrete multi-channel input from a

multi-format player, external decoder or sound processor.

Connect the output jacks on your multi-format player or

external decoder to the MULTI CH INPUT jacks. Be sure

to match the left and right output jacks to the left and right

input jacks for the front and surround channels.

Notes

• When you select the component connected to the MULTI CH INPUT

jacks as the input source (see page 19), this unit automatically turns off

the digital sound field processor, and you cannot select sound field

programs.

• This unit does not redirect signals input at the MULTI CH INPUT jacks

to accommodate for missing speakers. We recommend that you connect a

5.1-channel speaker system before using this feature.

• The source connected to the MULTI CH INPUT jacks on this unit cannot

be recorded.

Use the VIDEO AUX jacks on the front panel to connect a

game console or a video camera to this unit. To reproduce

the source signals input at these jacks, select “V-AUX” as

the input source.

Note

• The audio signals input at the PORTABLE mini jack take priority over

the ones input at the AUDIO L/R jacks.

DVD recorder Video HDMI out* HDMI (DVR)*

Video out (composite) VIDEO (DVR IN)

Audio Audio out (analog)* AUDIO (IN (PLAY))*

Audio recording Audio in (analog)* AUDIO (OUT (REC))*

Video recording Video in (composite)* VIDEO (DVR OUT)*

CD player Audio Coaxial out* OPTICAL (CD)*

Audio out (analog) AUDIO (CD)

MD or CD recorder Audio Audio out (analog)* AUDIO (IN (PLAY))*

Audio recording Audio in (analog)* AUDIO (OUT (REC))*

Component Signal type Jacks on component Jacks on this unit

Connecting a multi-format player or an

external decoder

L

R

L

R

MULTI CH INPUT

1

2

3

DVD

COAXIAL

CD

DTV/

CBL

DVD

FRONT CENTER

SUBWOOFER

SURROUND

DTV/CBL DV

R

IN

L

R

L

R

Front out

Surround out

Subwoofer out

Center out

Multi-format player or

external decoder

Using the VIDEO AUX jacks on the

front panel

Caution

Be sure to turn down the volume of this unit and other

components before making connections.

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Both FM and AM indoor antennas are supplied with this

unit. In general, these antennas should provide sufficient

signal strength. Connect each antenna correctly to the

designated terminals.

Notes

• The AM loop antenna should be placed away from this unit.

• A properly installed outdoor antenna provides clearer reception than an

indoor one. If you experience poor reception quality, install an outdoor

antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

• The AM loop antenna should always be connected, even if an outdoor

AM antenna is connected to this unit.

Connecting the wire of the AM loop antenna

Assembling the supplied AM loop antenna

Note

• The types of the supplied AM loop antenna is different depending on the

models.

Once all connections are complete, plug the power cable

into the AC wall outlet.

Press ASTANDBY/ON (or cPOWER) to turn on

this unit.

y

• When you turn on this unit, there will be a 4 to 5-second delay before this

unit can reproduce sound.

Press ASTANDBY/ON (or bSTANDBY) to turn

off this unit.

Note

• In the standby mode, this unit consumes a small amount of power in

order to receive infrared signals from the remote control.

Connecting the FM and AM antennas

D

EO

ANTENNA

R

SURR

O

AUDIO OUT

P

DVR

CD

S

N

OUT

DVR

AM

GND

FM

UNBAL.

75

N OUT

MONITOR

OUT

MD/

CD-R

OUT

(REC)

IN

(PLAY)

Outdoor AM antenna

Use a 5 to 10 m (16 to 32 ft)

of vinyl-covered wire

extended outdoors from a

window.

AM loop

antenna

(supplied)

Indoor FM

antenna

(supplied)

Ground

For maximum safety and minimum

interference, connect the antenna GND

terminal to a good earth ground. A good earth

ground is a metal stake driven into moist earth.

Open the

lever

Insert Close the

lever

Connecting the power cable

Turning on and off the power

Turning on this unit

Set this unit to the standby mode

L

Power cable

To the AC wall outlet

16 En

This unit has the Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts output

characteristics of your speakers based on speaker positions, speaker performances, and acoustic characteristics of the

room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit.

y

• Initial settings are indicated by (*) in the following each parameter.

1 Make sure of the following check points.

Before starting the automatic setup, check the

following check points.

• All speakers and subwoofer are connected

appropriately.

• Headphones are disconnected from this unit.

• This unit is turned on.

• The connected subwoofer is tuned on and the

volume level is set to about half way (or slightly

less).

• FRONT A speakers are selected as the front

speaker system (see page 19).

• The room is sufficiently quiet.

• The crossover frequency control of the connected

subwoofer is set to the maximum.

2 Connect the supplied optimizer microphone

to the OPTIMIZER MIC jack on the front

panel.

“SETUP•••••AUTO” appears on the front panel

display.

3 Place the optimizer microphone at your

normal listening position on a flat level

surface with the omni-directional

microphone heading upward.

y

• We recommend that you use a tripod (etc.) to affix the optimizer

microphone at the same height as your ears would be when you are

seated in your listening position. You can use the attached screw of

a tripod (etc.) to fix the optimizer microphone to the tripod (etc.).

4 Press ol / h to select “AUTO.”

Note

• “RELOAD” or “UNDO” is available only when you have

previously run “AUTO SETUP” and confirmed the results.

5 Press oENTER to start the setup

procedure.

This unit starts the automatic setup procedure. Loud

test tones are output from each speaker during the

audio setup procedure. After all settings

(“INITIALIZING,” “WIRING/LEVEL,”

“DISTANCE,” “SIZE”) are sequentially completed,

“FINISH” appears on the front panel display.

y

• To cancel the automatic setup, press ok.

Optimizing the speaker setting for your listening room (YPAO)

Notes

• Be advised that it is normal for loud test tones to be

output during the “AUTO SETUP” procedure. Do not

allow small children to enter the room during the

procedure.

• To achieve the best results, make sure that the room

is as quiet as possible while the “AUTO SETUP”

procedure is in progress. If there is too much ambient

noise, the results may not be satisfactory.

Using AUTO SETUP

VOLUME

MIN

MAX

MIN MAX

CROSSOVER

HIGH CUT

Controls of a subwoofer (example)

Choice Function

AUTO* Automatically runs the entire “AUTO

SETUP” procedure.

RELOAD Reloads the last “AUTO SETUP” settings and

overrides the previous settings.

UNDO Undoes the last “AUTO SETUP” settings and

restores the previous settings.

DEFAULT Resets the “AUTO SETUP” parameters to the

initial factory settings.

Optimizer microphone

Pagina se încarcă ...

Yamaha RX-V365 Manualul proprietarului

Yamaha RX-V365 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente