Yamaha DVD-S559MK Manualul proprietarului

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

2006

DVD-S559MK2

DVD PLAYER

LECTEUR DE DVD

G

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

Printed in China 3139 245 22201

00cv_DVD-S559MK2_G.fm Page 1 Wednesday, March 15, 2006 8:16 PM

i

Important notes for users in the

U.K.

Mains plug

This apparatus is fitted with an approved 13

Amp plug. To change a fuse in this type of plug

proceed as follows:

1

Remove fuse cover and fuse.

2

Fix new fuse which should be a BS1362 5 Amp,

A.S.T.A. or BSI approved type.

3

Refit the fuse cover.

If the fitted plug is not suitable for your jack

outlets, it should be cut off and an appropriate

plug fitted in its place.

If the mains plug contains a fuse, this should

have a value of 5 Amp. If a plug without a fuse

is used, the fuse at the distribution board should

not be greater than 5 Amp.

Note: The severed plug must be disposed to avoid

a possible shock hazard should it be inserted into

a 13 Amp jack elsewhere.

How to connect a plug

The wires in the mains lead are coloured with

the following code: blue = neutral (N),

brown = live (L).

●

As these colours may not correspond with the

colour markings identifying the terminals in your

plug, proceed as follows:

– Connect the blue wire to the terminal

marked N or coloured black.

– Connect the brown wire to the terminal

marked L or coloured red.

– Do not connect either wire to the earth

terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain

that the cord grip is clamped over the sheath of

the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require

consent. See Copyright Act 1956 and The

Performer’s Protection Acts 1958 to 1972.

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai

asetusten muutto saattaa altistaa vaaralliselle säteilylle

tai muille vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå

utsættelse for stråling.

Bemærk: Netafbryderen STANDBY/ON er

sekundært indkoblet og ofbryder ikke strømmen fra

nettet. Den indbyggede netdel er derfor tilsluttet til

lysnettet så længe netstikket sidder i stikkontakten.

N

Observer: Nettbryteren STANDBY/ON er sekundert

innkoplet. Den innebygdenetdelen er derfor ikke

frakoplet nettet så lenge apparatet er tilsluttet

nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sätt än i

denna bruksanvisning specificerats, kan användaren

utsättas för osynlig laserstrålning, som överskrider

gränsen för laserklass 1.

Observera! Strömbrytaren STANDBY/ON är

sekundärt kopplad och inte bryter inte strömmen från

nätet. Den inbyggda nätdelen är därför ansluten till

elnätet så länge stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä

käyttöohjeessa mainitulla tavalla saattaa altistaa

käyttäjän turvallisuusluokan 1 ylittävälle

näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina

tippu-ja roiskevedelle.

Toiminnanvalitsin STANDBY/ON on kytketty

toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä

sähköverkkoon aina silloin, kun pistoke on

pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD OCH SPÄRREN ÄR

URKOPPLAD. BETRAKTA EJ STRÅLEN.

ii

CAUTION

Use of controls or adjustments or performance

of procedures other than those specified

herein may result in hazardous radiation

exposure.

ATTENTION

L’emploi de commandes, de réglages ou un

choix de procédures différents des

spécifications de cette brochure peut

entraîner une exposition à d’éventuelles

radiations pouvant être dangereses.

ACHTUNG

Die Verwendung von Bedienungselementen

oder Einstellungen oder die Durchführung

von Bedienungsvorgängen, die nicht in

dieser Anleitung aufgeführt sind, kann zu

einem Kontakt mit gefährlichen Laserstrahlen

führen.

OBSERVERA

Användning av kontroller och justeringar eller

genomförande av procedurer andra än de

som specificeras i denna bok kan resultera i

att du utsätter dig för farlig strålning.

ATTENZIONE

Uso di controlli o regolazioni o procedure non

specificamente descritte può causare

l’esposizione a radiazioni di livello pericoloso.

PRECAUCIÓN

El uso de los controles o los procedimientos

de ajuste o utilización diferentes de los

especificados en este manual pueden

causar una exposición peligrosa a la

radiación.

VOORZICHTIG

Gebruik van bedieningsorganen of

instellingen, of uitvoeren van handelingen

anders dan staan beschreven in deze

handleiding kunnen leiden tot blootstelling

aan gevaarlijke stralen.

ПРЕДУПРЕЖДЕНИЕ

Использование органов управления или

настроек или выполнение процедур,

отличных от описанных в данном

руководстве, могут привести к опасному

облучению.

OO

SS

TT

RR

ZZ

EE

ŻŻ

EE

NN

II

EE

Używanie regulatorów i nastawień w inny

sposób lub wykonywanie procedur innych

niż tutaj podane może być przyczyną

niebezpiecznego promieniowania.

CAUTION

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN. AVOID EXPOSURE TO BEAM.

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.

UNDGÅ UDSÆTTELSE FOR STRÅLING.

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL

ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING

SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VARO!

AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA

NÄKYMÄTTÖMÄLLE LASER SÄ TEILYLLE. ÄLÄ KATSO

SÄTEESEEN.

VORSICHT

SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM

STRAHL AUSSETSEN.

DANGER

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN. AVOID DIRECT EXPOSURE TO BEAM.

ATTENTION

RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS

D’OUVERTURE. EXPOSITION DANGEREUSE AU

FAISCEAU.

ПРЕДУПРЕЖДЕНИЕ

ПРИ ОТКРЫТИИ УСТРОЙСТВА ВЫ МОЖЕТЕ

ПОДВЕРГНУТЬСЯ ВОЗДЕЙСТВИЮ ВИДИМОГО

И НЕВИДИМОГО ЛАЗЕРНОГО ИЗЛУЧЕНИЯ.

ИЗБЕГАЙТЕ ВОЗДЕЙСТВИЯ ЛУЧА.

OSTRZEŻENIE

WIDZIALNE I NIEWIDZIALNE PROMIENIOWANIE

LASEROWE PO OTWARCIU. UNIKAĆ NARAŻENIA

NA WIĄZKĘ LASEROWĄ.

AVOID DIRECT EXPOSURE TO THE BEAM

INVISIBLE LASER RADIATION WHEN OPEN

DANGER:

DO NOT STARE INTO BEAM

INVISIBLE LASER RADIATION WHEN OPEN

CAUTION:

iii

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1

To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2

Install this unit in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources,

vibration, dust, moisture, or cold. In a cabinet,

allow about 2.5cm (1 inch) of free space all

around this unit for adequate ventilation.

3

Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4

Do not expose this unit to sudden temperature

changes from cold to hot, nor locate this unit in

an environment with high humidity (i.e., a room

with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5

Avoid installing this unit in a location where

foreign objects may fall onto this unit or where

this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may

cause fire, damage to this unit, and/or personal

injury.

– Containers with liquid in them, as they may fall,

spilling the liquid and causing an electrical

shock to the user and/or damage to this unit.

6

Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7

Do not plug in this unit to a wall outlet until all

connections are complete.

8

Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9

Do not use excessive force on switches, knobs

and/or cords.

10

When disconnecting the power cord from the

wall outlet, grasp the plug; do not pull the cord.

11

Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12

Use only the voltage specified on this unit. Using

this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from

use of this unit with a voltage other than as

specified.

13

Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reason.

14

When not planning to use this unit for long

periods of time (i.e., vacation), disconnect the AC

power plug from the wall outlet.

15

Be sure to read the “Troubleshooting” section on

common operating errors before concluding that

this unit is faulty.

16

Before moving this unit, press STANDBY/ON to

set the unit in standby mode, then disconnect the

AC power plug from the wall outlet.

17

Install this unit near the AC outlet and where the

AC power plug can be reached easily.

LASER SAFETY

This unit employs a laser. Due to possible eye injury,

only a qualified service person should remove the

cover or attempt to service this device.

DANGER

This unit emits visible laser radiation when open.

Avoid direct eye exposure to beam.

When this unit is plugged into a wall outlet, do not

place your eyes close to the opening of the disc tray

and other openings or look inside.

The unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

LASER

Type Semiconductor laser GaAlAs

Wave length 650 nm (DVD)

780 nm (VCD/CD)

Output Power 7 mW (DVD)

10 mW (VCD/CD)

Beam divergence 60 degree

1

En

English

Contents

Introduction

Region codes...............................................................3

Supplied accessories..................................................3

Notes about discs/content format.........................3

Cleaning discs..............................................................4

Patent information.....................................................4

Functional Overview

Front panel ..................................................................5

Rear panel....................................................................5

Remote control..........................................................6

Connections

General notes on connections................................7

Audio connections.....................................................7

Digital connection ................................................................7

Analog connection...............................................................7

Video connections .....................................................8

Component video jacks <A>.......................................8

S-video jack <B>..................................................................8

Composite video jack <C> ...........................................8

SCART terminal <D>.......................................................8

Getting Started

Inserting batteries into the remote control.........9

Using the remote control................................................9

Turning on the power............................................ 10

Setting a TV type and display ............................... 10

Setting a color system for your TV.........................10

Setting an aspect ratio for your TV.........................11

Setting a language preference............................... 11

Setting the OSD Language...........................................11

Setting the audio, subtitle and disc menu

languages (DVD-Video only)......................................12

Disc Operations

Basic playback...........................................................13

General operation...................................................13

Pausing playback.................................................................13

Selecting track/chapter ...................................................13

Searching backward/forward.......................................13

Stopping playback..............................................................13

Selecting the various repeat/shuffle functions....14

Repeat and shuffle.............................................................14

Repeating a section within a chapter/track.........14

Operations for video playback (DVD/VCD/SVCD) ...14

Using the disc menu.........................................................14

Slow motion.........................................................................14

Zooming in............................................................................15

Resuming playback from the last stopped point....15

On-screen display (OSD).............................................15

Special DVD features ............................................. 16

Playing by title......................................................................16

Camera angle.......................................................................16

Audio........................................................................................17

Subtitles...................................................................................17

Special VCD/SVCD features.................................17

Playback control (PBC)..................................................17

Preview function ................................................................17

Playing data discs (MP3/WMA/JPEG/DivX).......... 18

General operation.............................................................18

Selecting a folder and track/file..................................19

Repeat and shuffle.............................................................19

Special picture disc features..................................19

Preview function ................................................................19

Zooming pictures..............................................................19

Playback with multi-angles............................................20

Scan effect..............................................................................20

Playing MP3 music and JPEG picture

simultaneously .....................................................................20

Special DivX features .............................................20

Interactive menu ................................................................20

Multiple audio and subtitle languages ....................20

2

En

Contents

Setup Menu

General setup menu............................................... 21

Locking/Unlocking the disc for viewing.................21

Dimming the front panel display...............................21

Programming disc tracks (except MP3/WMA/

JPEG/DivX)............................................................................21

OSD language .....................................................................22

Screen saver .........................................................................22

Sleep timer............................................................................22

Auto standby........................................................................23

DivX

®

VOD registration code..................................23

Audio setup menu................................................... 23

Setting the analog output..............................................23

Setting the digital output...............................................24

CD upsampling ...................................................................24

Night mode...........................................................................25

Lip synchronization...........................................................25

Video setup menu................................................... 25

TV type....................................................................................26

Setting the TV display .....................................................26

Progressive ............................................................................27

Picture setting......................................................................27

Switching the YUV/RGB................................................28

Preference setup menu.......................................... 28

Audio, subtitle and disc menu....................................28

Restricting playback with parental control..........29

Playback of VR format....................................................29

MP3/JPEG menu.................................................................30

Displaying DivX external subtitle files ...................31

Changing the password..................................................31

PBC (Playback control)..................................................32

Resetting the system........................................................32

Language Codes......................... 33

Troubleshooting ........................ 35

Glossary ...................................... 37

Specifications ............................. 39

3

En

English

Introduction

Thank you for purchasing this unit. This

Owner’s Manual explains the basic

operation of this unit.

DVD discs must be labeled ALL

regions or Region 2 in order to

play on this unit.

You cannot play discs labeled for

other regions.

– Remote control

– Two batteries (AA, R06, UM-3) for the

remote control

– Audio pin cable

– Video pin cable

– Owner’s Manual

– This unit can play the disc types

associated with the logos shown below.

Do not attempt to load any other type

of disc into this unit. Doing so may

damage this unit.

– This unit can play

DVD+R/RW/R DL and

DVD-R/RW/R DL

discs recorded in

DVD-Video compatible format.

– This unit can play DVD-RW discs

recorded in VR format (compatible with

CPRM).

– This unit can play the following data

discs (

For MP3 and WMA files, the

parenthetic words represent the

compatible sampling rate and bit rate):

– MP3 files recorded on CD-R/RW,

DVD+R/RW and DVD-R/RW

(fs 32, 44.1, 48 kHz / 96

–

320 kbps

(CBR only))

– WMA files recorded on CD-R/RW,

DVD+R/RW and DVD-R/RW

(When in fs 44.1 kHz: 64

–

192 kbps /

When in fs 48 kHz: 128

–

192 kbps

(CBR only))

– JPEG (except Progressive JPEG) files

recorded on CD-R/RW, DVD+R/

RW and DVD-R/RW (compatible

resolution: 3072 x 2048 or less)

– KODAK Picture CD

– FUJICOLOR CD

– DivX Video files recorded on CD-R/

RW, DVD+R/RW and DVD-R/RW

– Official DivX

®

Ultra Certified

product

– Plays all versions of DivX

®

video

(including DivX

®

6) with enhanced

playback of DivX

®

media files and

the DivX

®

Media Format

– ISO 9660 Level1/Level2 for CD-R/RW

– Up to 298 folders per disc and up to

648 files per folder with up to 8

hierarchies

– CD-R/RW, DVD+R/RW

/R DL

and

DVD-R/RW

/R DL

cannot be played

unless finalized.

– Only the first session of DVD+R

/R DL

and DVD-R/RW

/R DL

can be played.

– Some discs cannot be played depending

on disc characteristics or recording

conditions.

– Do not use any non-standard shaped

discs (heart-shaped, etc.).

– Do not use discs with tape, seals, or

paste on their surface.

– Do not use discs with many scratches

on their surface.

Region codes

Supplied accessories

Notes about discs/content format

ALL

2

4 En

Introduction

• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center

out. Do not wipe in a circular motion.

• Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic

spray intended for analog records.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are

trademarks of Dolby Laboratories.

”DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

Cleaning discs

Patent information

This product incorporates copyright protection technology that is protected by method claims of certain

U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

5 En

English

Functional Overview

1 STANDBY/ON

Turns on this unit or sets it to the standby

mode.

2 Disc tray

Loads a disc in the disc tray.

3 OPEN/CLOSE (/)

Opens or closes the disc tray.

4 PROGRESSIVE indicator

Lights up when this unit enters the progressive

mode.

5 Front panel display

Shows the current status of this unit.

6 PLAY (B)

Starts playback.

7 PAUSE (;)

Pauses playback.

8 STOP (9)

Stops playback.

1 AC power cord

Connect to a standard AC outlet.

2 AUDIO OUT (L, R) jacks

Connect to the audio input jacks of your AV

receiver or stereo system.

3 DIGITAL OUT - COAXIAL jack

Connect to the coaxial input jack of your AV

receiver.

4 VIDEO OUT - COMPONENT (Y, PB/CB,

PR/CR) jacks

Connect to the component input jacks of your

AV receiver.

5 VIDEO OUT - S VIDEO jack

Connect to the S-video input jack of your AV

receiver.

6 VIDEO OUT - VIDEO jack

Connect to the composite video input jack of

your AV receiver.

7 AV terminal

Connect to SCART input terminal of your TV.

Caution: Do not touch the inner pins of the jacks on the rear panel of this unit.

Electrostatic discharge may cause permanent damage to this unit.

Front panel

1 2 3 4 5 6 7 8

Rear panel

7123456

6 En

Functional Overview

1

Turns on this unit or sets it to the

standby mode.

2 TOP MENU/RETURN

Displays the top-level disc menu (DVD).

Moves back to the previous menu (DVD*/

VCD).

3 MENU

Accesses the menu of a disc (DVD).

Switches PBC on or off (VCD).

4 1 / 2/3 / 4

Selects an item in the currently displayed

menu. Search or slow playback.

ENTER/OK

Confirms the menu selection.

5 S

Searches backward.*

Moves to the previous chapter or track.

6 STOP (9)

Stops playback.

7 SUBTITLE

Selects the subtitle language.

8 ANGLE

Selects the DVD camera angle.

9 REPEAT

Repeats the chapter, track, title or disc.

Shuffles the chapter or track.

0 A-B

Repeats a specific segment.

q Numeric buttons (0-9)

Selects numbered items in the currently

displayed menu.

w ON SCREEN

Accesses or exits from the on-screen

display (OSD) menu of this unit.

e SETUP

Accesses or exits from the setup menu

of this unit.

r T

Searches forward.*

Moves to the next chapter or track.

t PLAY (B)

Starts playback.

y PAUSE (;)

Pauses playback temporarily.

Frame-by-frame playback.

u AUDIO

Selects the audio language or format.

i ZOOM

Enlarges the video image.

o MUTE

Mutes the audio output. Press again to restore

the audio output to previous volume level.

p SCAN

Previews the content of a track or whole disc

(VCD).

Plays the first 6 seconds or less of each track

(CD).

* Press and hold the button for about two

seconds.

Remote control

MENU SETUP

ENTER

OK

STOP

ANGLE

A B

PAUSE

PLAY

1

2

3

4

5

6

7

8

0

9

TOP MENU RETURN

ON SCREEN

DVD13

ZOOM AUDIO

SUBTITLE

REPEAT

SCAN MUTE

1

2

3

4

7

8

9

0

5

6

q

w

e

r

t

y

u

i

o

p

7 En

English

Connections

Be sure to turn off this unit and unplug the

power supply cable, before you make or

change connections.

• Depending on the equipment you wish

to connect, there are various ways to

make connections. Possible connections

are described below.

• Refer to the manuals of your other

components as necessary to make the

best connections.

• Do not connect this unit via your VCR.

The video quality could be distorted by

the copy protection system.

• Do not connect the audio out jack of

this unit to the phono in jack of your

audio system.

Digital connection

This unit has a coaxial digital out jack.

Connect DIGITAL OUT - COAXIAL jack

of this unit to your AV receiver equipped

with Dolby Digital, DTS, or MPEG

decoder using a commercially available

coaxial cable.

You need to set “DIGITAL OUTPUT” to

“ALL” (see “DIGITAL OUTPUT” on

page 24).

Notes:

– If the audio format of the digital output

does not match the capabilities of your

receiver, the receiver produces a distorted

sound or no sound at all. Make sure to

select the appropriate audio format from

the menu screen on the disc.

Pressing AUDIO on the remote control once

or more may change not only the audio

languages but also the audio format. The

selected format appears in the front panel

display for several seconds.

– If you wish to enjoy Dolby Digital, DTS and

MPEG formats, you must connect this unit

to an AV receiver that supports these

formats.

Analog connection

This unit has analog output jacks.

Connect AUDIO OUT (L, R) jacks of this

unit to the corresponding input jacks of

your audio component (such as a stereo

amplifier) using the supplied audio pin

cable.

General notes on connections

Audio connections

COAXIAL

IN

C

AV receiver

Left front

speaker

Right surround

speaker

Center

speaker

Subwoofer

Right front

speaker

Left surround

speaker

Surround

back speaker

This unit

CD/DVD

L

R

L

R

L

Right

speaker

Left

speaker

Audio pin cable

(supplied)

This unit

Stereo

amplifier

8 En

Connections

If your AV receiver has video output jacks,

connect your receiver and then your TV

so that you can use one TV for several

different video sources (LD, VCR, etc.) by

simply switching the input source selector

of your receiver.

This unit has four types of video output

jacks. Use the one that corresponds to the

input jacks of the component to be

connected.

Component video jacks <A>

Component video connections achieve

high fidelity color reproduction than S-

video connections by transmitting video

signals on separate wires for luminance (Y:

green) and chrominance (P

B: blue, PR: red).

Connect VIDEO OUT - COMPONENT

(Y, P

B/CB, PR/CR) jacks of this unit to

component input jacks of your AV receiver

and then to those of your TV using a

commercially available component cable.

Observe the color of each jack when you

make connections.

If your receiver does not have component

output jacks, you can achieve a better

video image by connecting the component

output jacks of this unit directly to the

component input jacks of your TV.

Note:

– You need to set “COMPONENT” to “YUV”

(see “Switching the YUV/RGB” on

page 28).

S-video jack <B>

S-video connections achieve a clearer

picture than composite video connections

by transmitting video signals on separate

wires for luminance (Y) and chrominance

(C).

Connect VIDEO OUT - S VIDEO jack of

this unit to S-video input jack of your AV

receiver and then to that of your TV using

a commercially available S-video cable.

Composite video jack <C>

Connect VIDEO OUT - VIDEO jack of this

unit to video input jack of your AV

receiver and then to that of your TV using

the supplied video pin cable.

SCART terminal <D>

If your TV has only a terminal for video

input, you can connect the TV directly to

this unit.

Connect AV terminal of this unit to

SCART input terminal of your TV using a

commercially available SCART cable.

Note:

– Ensure that the “TV” indication on SCART

cable is connected to the TV set and “DVD”

indication on SCART cable is connected to

this unit.

Video connections

VIDEO

OUT

VIDEO

IN

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

S VIDEO

OUT

S VIDEO

IN

COMPONENT

VIDEO IN

S VIDEO

INPUT

VIDEO

INPUT

YPB/CBPR/CR

PR

Y

PB

PR

Y

PB

S

V

AV receiver

Video pin cable

(supplied)

This unit

9 En

English

Getting Started

1 Open the battery compartment.

2 Insert the two supplied batteries (AA, R06,

UM-3) following the indications (+/–)

inside the compartment.

3 Close the cover.

Notes:

– Insert batteries correctly according to the

polarity markings (+/–). The batteries

inserted in the opposite direction may leak.

– Replace the exhausted batteries

immediately with new ones to prevent a

leakage.

– Remove the batteries from the

compartment if the remote control is not

used for more than a month.

– If the batteries have leaked, dispose of

them immediately. Avoid touching the

leaked material or letting it come into

contact with clothing, etc. Clean the battery

compartment thoroughly before installing

new batteries.

– Do not use old batteries together with new

ones.

– Do not use different types of batteries (such

as alkaline and manganese batteries)

together. Read the packaging carefully as

these different types of batteries may have

the same shape and color.

– Dispose of the batteries correctly in

accordance with your local regulations.

Using the remote control

Handling the remote control

• Do not spill water or other liquids on

the remote control.

• Do not drop the remote control.

• Do not leave or store the remote

control in the following types of

conditions:

– places of high humidity, such as near a

bath

– places of high temperature, such as near

a heater or stove

– places of extremely low temperature

– dusty places

Step1: Inserting batteries

into the remote control

2

1

3

2

30°

Point the remote control at

the remote control sensor,

within approximately 6 m

(20 feet) from this unit.

Remote control

sensor

10 En

Getting Started

1 Connect the AC power cord to the power

outlet.

2 Turn on your TV and AV receiver.

3 Select the appropriate input source of the

AV receiver connected to this unit. Refer

to the manual supplied with your AV

receiver for details.

4 Turn on this unit.

5 Set the TV to the correct Video IN channel

(e.g. EXT1, EXT2, AV1, AV2, AUDIO/

VIDEO, etc. Refer to the manual supplied

with your TV for details).

➜ The front panel display lights up and the

default screen appears on the TV.

Setting a color system for your

TV

This unit is compatible with both NTSC

and PAL video formats. Select the color

system that matches your TV.

1 Press SETUP.

2 Press 2 repeatedly to select “VIDEO

SETUP PAGE”.

3 Press 3

/ 4 to highlight [TV TYPE], and

then press 2.

4 Press 3

/ 4 to highlight one of the following

options.

PAL

Select this if the connected TV is a PAL

system TV. It will change the video signals

of NTSC discs and output them in PAL

format.

NTSC

Select this if the connected TV is an NTSC

system TV. It will change the video signals

of PAL discs and output them in NTSC

format.

MULTI

Select this if the connected TV is

compatible with both NTSC and PAL

formats (such as a multi-system TV).

The output format will be in accordance

with the video signals of the disc.

5 Select an item, and then press

ENTER/OK to confirm your selection.

Notes:

– Before changing the current TV standard

setting, ensure that your TV supports the

selected TV type.

– If the picture is not displayed properly on

your TV, wait for 15 seconds for this unit to

activate automatic recovery.

Step2: Turning on the power

Step3: Setting a TV type and

display

VIDEO SETUP PAGE

TV TYPE PAL

TV DISPLAY NTSC

PROGRESSIVE MULTI

PICTURE SETTING

COMPONENT

TIPS: To return to the previous menu, press 1.

To exit from the menu, press SETUP.

CANCELOK

CHANGING PAL TO NTSC:

1. ENSURE THAT YOUR TV SUPPORTS

NTSC STANDARD.

2. IF THERE IS A DISTORTED PICTURE

DISPLAYED ON THE TV, WAIT 15

SECONDS FOR AUTO RECOVER.

11 En

English

Getting Started

Setting an aspect ratio for your

TV

You can set the aspect ratio of this unit to

match your TV. If the aspect ratio of your

TV is 4:3, you do not need to change this

setting. If you have a widescreen TV,

change this setting according to the

following procedure.

For details, see “Setting the TV display” on

page 26.

1 Press SETUP.

2 Press 2 repeatedly to select “VIDEO

SETUP PAGE”.

3 Press 3

/ 4 to highlight [TV DISPLAY], and

then press 2.

4 Press 3

/ 4 to highlight [16:9], and then

press ENTER/OK to confirm the

selection.

You can select your own preferred

language settings.This unit automatically

switches to your preferred language

whenever you load a disc. If the selected

language is not available on the disc, the

default language of the disc will be used

instead. The OSD language in the system

menu remains once selected.

Setting the OSD Language

1 Press SETUP.

2 Press 1 / 2 to select “GENERAL SETUP

PAGE”.

3 Press 3

/ 4 to highlight [OSD

LANGUAGE], and then press 2.

4 Press 3

/ 4 to select a language, and then

press ENTER/OK to confirm your

selection.

VIDEO SETUP PAGE

TV TYPE

TV DISPLAY 4:3 PAN SCAN

PROGRESSIVE 4:3 LETTER BOX

PICTURE SETTING 16:9

COMPONENT

TIPS: To return to the previous menu, press 1.

To exit from the menu, press SETUP.

Step4: Setting a language

preference

GENERAL SETUP PAGE

DISC LOCK ENGLISH

DISPLAY DIM DANSK

PROGRAM DEUTSCH

OSD LANGUAGE ESPAÑOL

SCREEN SAVER FRANÇAIS

SLEEP ITALIANO

AUTO STANDBY NEDERLANDS

DIVX(R) VOD CODE NORSK

12 En

Getting Started

Setting the audio, subtitle and

disc menu languages

(DVD-Video only)

1 Press STOP (9) twice, and then press

SETUP.

2 Press 2 repeatedly to select

“PREFERENCE PAGE”.

3 Press 3

/ 4 to highlight one of the options

below at a time, and then press 2.

– AUDIO (audio language)

– SUBTITLE (subtitle language)

– DISC MENU (disc menu language)

4 Press 3

/ 4 to select a language, and then

press ENTER/OK to confirm your

selection.

If the language you want is not in the

list, select [OTHERS],

and then use the numeric buttons (0-9)

on the remote control to enter the 4-digit

language code (see “Language Codes” on

page 33), and then press ENTER/OK to

confirm the code.

5 Repeat steps 3–4 for other language

settings.

PREFERENCE PAGE

AUDIO ENGLISH

SUBTITLE CHINESE (SIMP)

DISC MENU FRENCH

PARENTAL SPANISH

VR LIST PORTUGUESE

MP3/JPEG NAV POLISH

DIVX SUBTITLE ITALIAN

PASSWORD TURKISH

TIPS: To return to the previous menu, press 1.

To exit from the menu, press SETUP.

13 En

English

Disc Operations

IMPORTANT!

– If the inhibition icon ( or X)

appears on the TV screen when a

button is pressed, the function for

that button is not available on the

current disc or at the current time.

– Depending on the DVD or VIDEO

CD disc, some operations may

operate differently or be

restricted.

– Do not push on the disc tray or put

any objects other than discs on the

disc tray. Doing so may cause the

disc player to malfunction.

1 Press STANDBY/ON on the front panel

or on the remote control to turn on

this unit.

2 Press OPEN/CLOSE (/) on the front

panel to open the disc tray.

3 Place the disc in the disc tray with the

printed side up.

4 Press OPEN/CLOSE (/) again to close

the disc tray.

➜ After recognizing the disc, this unit

begins to play back automatically.

• If you press PLAY (B) when the disc

tray is open, the disc tray closes and

playback starts automatically.

Unless stated otherwise, all operations

described here are carried out using the

supplied remote control.

Pausing playback

1 During playback, press PAUSE (;).

➜ Playback is paused and the sound is

muted.

2 Press PAUSE (;) again to select the next

picture frame.

3 To resume normal playback, press

PLAY (B).

Selecting track/chapter

• Press S / T or use the numeric

buttons (0-9) to select a track/chapter

number.

• During repeated playback, press S /

T to replay the same track/chapter.

Searching backward/forward

1 Press and hold S / T or press 1 / 2.

2 While searching, press S / T or

1

/ 2 repeatedly to select the desired

speed.

3 To resume normal playback, press

PLAY (B).

Notes:

– 1

/ 2 key may not be available with some

discs.

– For MP3 and WMA, the search function

allows you to search the track currently

being played.

Stopping playback

• Press STOP (9).

Basic playback

General operation

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

14 En

Disc Operations

Repeat and shuffle

• Each time you press REPEAT during

playback, the front panel display changes

as follows:

DVD

➔ RPT ONE (repeat chapter)

➔ RPT TT (repeat title)

➔ SHUFFLE (shuffle)

➔ RPT SHF (shuffle repeat)

➔ RPT OFF (repeat off)

VCD/SVCD/CD

➔ RPT ONE (repeat track)

➔ RPT ALL (repeat disc)

➔ SHUFFLE (shuffle)

➔ RPT SHF (shuffle repeat)

➔ RPT OFF (repeat off)

MP3/WMA/DivX

➔ RPT ONE (repeat track)

➔ RPT FLD (repeat folder)

➔ SHUFFLE (shuffle)

➔ RPT OFF (repeat off)

Note:

– For VCD, repeat playback is not possible

when the PBC mode is selected.

Repeating a section within a

chapter/track

1 While playing a disc, press A-B at the

desired starting point.

2 Press A-B again at the desired end point.

•A and B can only be set within the same

chapter/track.

➜ The selected section repeats

continuously.

3 To exit from the sequence, press A-B.

Using the disc menu

Depending on the disc, a menu may appear

on the TV screen once you load the disc.

To select a playback feature or item

• Use

1 / 2/3 / 4 or the numeric buttons

(0-9), and then press ENTER/OK to

start playback.

To access or exit from the menu

• Press MENU.

Slow motion

You can play back in slow motion.

1 Press 3 for reverse slow motion or 4 for

forward slow motion.

2 During slow motion, press 3

/ 4

repeatedly to select the desired speed.

3 To resume normal playback, press

PLAY (B).

Note:

– Reverse slow motion is not available for

VCDs and SVCDs.

Selecting the various repeat/

shuffle functions

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

Operations for video playback

(DVD/VCD/SVCD)

15 En

English

Disc Operations

Zooming in

This function allows you to enlarge or

lessen the picture on the TV screen and to

pan through the enlarged picture.

1 During playback, press ZOOM repeatedly

to display the picture at different scales.

• Use

1 / 2/3 / 4 to pan through the

enlarged picture.

➜ Playback continues.

2 Press ZOOM repeatedly to return to the

original size.

Resuming playback from the last

stopped point

You can resume playback of the last 10

discs, even if the discs were ejected or the

power of this unit was turned off.

1 Load one of the last 10 discs.

➜ “LOADING” appears on the TV screen.

2 Press PLAY (B) while “LOADING” is

displayed on the TV screen.

➜ “RESUME PLAY” appears on the TV

screen and the disc is played back from

the last point.

To cancel the resume mode

• When playback is stopped, press

STOP (9) again.

On-screen display (OSD)

The OSD menu shows disc playback

information (e.g., the title or chapter

number, elapsed playing time or audio/

subtitle language). A number of operations

are possible without interrupting disc

playback.

1 During playback, press ON SCREEN.

➜ A list of available disc information

appears on the TV screen.

DVD

VCD/SVCD

2 Press 3 / 4 to view the information, and

then press ENTER/OK to access the

selected item.

3 Use the numeric buttons (0-9) to input

the number/time or press 3

/ 4 to make a

selection, and then press ENTER/OK to

confirm the selection.

➜ Playback changes to the selected time

or to the selected title/chapter/track.

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

MENU

TITLE 02/14

CHAPTER 02/14

AUDIO 5.1CH

SUBTITLE ENG

BITRATE 16 TITLE ELAPSED 0:02:25

MENU

TRACK 02/14

DISC TIME 0:49:17

TRACK TIME 0:03:43

REPEAT OFF

BITRATE 16 TOTAL ELAPSED 0:02:25

16 En

Disc Operations

Title/Chapter/Track selection

(DVD/VCD)

1 Press 3

/ 4 to select [TITLE] or

[CHAPTER] (DVD) or [TRACK] (VCD).

2 Press ENTER/OK to confirm the

selection.

3 Select a title, chapter or track number

using the numeric buttons (0-9).

Time search (DVD/VCD)

1 Press 3

/ 4 to select [TT TIME] or [CH

TIME] (DVD) or [TRACK TIME] or [DISC

TIME] (VCD).

• [TT TIME] refers to the total time of the

current title, and [CH TIME] refers to

the total time of the current chapter.

2 Press ENTER/OK to confirm the

selection.

3 Enter hours, minutes and seconds from left

to right using the numeric buttons (0-9)

(e.g. 0:34:27).

Audio/Subtitle/Angle (DVD)

You can change [AUDIO], [SUBTITLE] or

[ANGLE] if these functions are available on

the disc you are playing.

1 Press 3

/ 4 to select [AUDIO],

[SUBTITLE] or [ANGLE].

2 Press ENTER/OK to confirm the

selection.

3 For Audio and Subtitle:

Press 3

/ 4 to highlight your selection, and

then press ENTER/OK.

OR

For Angle:

Select an angle using the numeric

buttons (0-9).

Repeat/Time Display (DVD/VCD)

1 Press 3

/ 4 to select [REPEAT] or [TIME

DISP.].

2 Press ENTER/OK to confirm the

selection.

3 Press 3

/ 4 to highlight your selection, and

then press ENTER/OK.

Time display (CD)

Each time you press ON SCREEN, the

time display changes as follows:

Playing by title

1 Press MENU.

➜ The disc title menu appears on the TV

screen.

2 Use

1 / 2/3 / 4 or the numeric buttons

(0-9) to select a playback option.

3 Press ENTER/OK to confirm your

selection.

Camera angle

• Press ANGLE repeatedly to select the

desired angle.

Special DVD features

TOTAL ELAPSED TOTAL REMAIN

SINGLE REMAIN

SINGLE ELAPSED

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

Pagina se încarcă ...

Yamaha DVD-S559MK Manualul proprietarului

Yamaha DVD-S559MK Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente