Yamaha DSP-A2 Manualul proprietarului

NATURAL SOUND AV AMPLIFIER DSP-A2

CINEMA DSP 7ch

VOLUME

INPUT SELECTOR

INPUT MODE

l6

20

28

40

60

l2

8

4

2

0

–dB

BASS TREBLE BALANCE

VCR 2

VIDEO AUX

REC OUT

VCR 1

TV/DBS

PHONO

TUNER

CD

DVD/LD

SOURCE

TAPE/MD

VIDEO AUX

EFFECT

EXT. DECODER

55

4

3

2

l

0

l

2

3

4

LR

55

4

3

2

l

0

l

2

3

4

55

4

3

2

l

0

l

2

3

4

STANDBY/ON

PHONES

BASS

EXTENSION

TONE

BYPASS

A

SPEAKERS

B

PROGRAM

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

AMPLIFICATEUR AUDIO-VIDEO

NATURAL SOUND AV AMPLIFIER

G B R T

Congratulations!

You are the proud owner of a Yamaha Digital Sound Field Processing (DSP)

System—an extremely sophisticated audio component. The DSP system takes full

advantage of Yamaha’s undisputed leadership in the field of digital audio processing

to bring you a whole new world of listening experiences. Follow the instructions in this

manual carefully when setting up your system, and the DSP system will sonically

transform your room into a wide range of listening environments—anything from a

famous concert hall to a cozy jazz club. In addition, you get incredible realism from

most of surround-sound encoded video sources available in the market using the built-

in Dolby Pro Logic Surround Decoder, Dolby Digital Decoder and DTS Decoder.

Seven built-in channels of amplification on this model mean that no additional

amplifiers are required to enjoy advanced digital sound field processing.

Rather than tell you about the wonders of digital sound field processing, however,

let’s get right down to the business of setting up the system and trying out its many

capabilities. Please read this operation manual carefully and store it in a safe place for

later reference.

1

English

CAUTION .................................................................. 2

INTRODUCTION ....................................................... 3

Features .................................................................... 3

What’s DSP?............................................................. 4

GETTING STARTED ................................................ 7

Getting started.......................................................... 7

Unpacking.............................................................. 7

Opening and closing the front cover ...................... 7

Installing batteries in the remote controller ........... 8

Notes about the remote controller.......................... 8

Controls and their functions................................... 9

Front panel............................................................. 9

Display panel........................................................ 11

PREPARATION ...................................................... 12

Speaker setup......................................................... 12

Connections ........................................................... 14

Audio/video source equipment ............................ 14

Speakers ............................................................. 21

Plugging in this unit ............................................. 24

On screen display.................................................. 25

Selecting the output modes

(“SET MENU” mode) ............................................. 26

Speaker balance adjustment ................................ 29

BASIC OPERATION ............................................... 32

Playing a source .................................................... 32

Recording a source to tape (or MD) or dubbing

from tape (or MD) to tape (or MD)......................... 37

Sound control......................................................... 39

Using digital sound field processor (DSP) ......... 40

Playing a source with an effect of the digital

sound field processor (DSP)................................ 40

Adjusting output level of the center, right rear,

left rear, front effect speakers and subwoofer...... 43

Brief overview of digital sound field programs...... 45

ADVANCED FEATURES ....................................... 50

SET MENU mode ................................................... 50

Creating your own sound fields .......................... 54

Setting the SLEEP timer ....................................... 59

REMOTE CONTROLLER ....................................... 60

Basic operation (Cover is open) .......................... 60

Using the “learning-capable” keys

(Cover is open)....................................................... 62

Using OPERATION CONTROL keys

(Cover is closed) ................................................... 64

Macro operations (Cover is closed) .................... 66

Methods of learning and clearing functions ....... 68

TROUBLESHOOTING ............................................ 71

SPECIFICATIONS .................................................. 74

CONTENTS

2

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from windows,

heat sources, sources of excessive vibration, dust, moisture and

cold. Avoid sources of humming (transformers, motors). To

prevent fire or electrical shock, do not expose the unit to rain or

water.

3. Never remove the unit cover. Contact your dealer if an object falls

inside the unit.

4. Do not use force on switches, controls or connection wires. When

moving the unit, first disconnect the power plug and the wires

connected to other equipment. Never pull on the wires

themselves.

5. The openings on the unit cover assure proper ventilation of the

unit. If these openings are obstructed, the temperature inside the

unit will rise rapidly. Therefore, avoid placing objects against these

openings, and install the unit in a well-ventilated area to prevent

fire and damage.

Be sure to allow a space of at least 10 cm behind, 20 cm on the

both sides and 30 cm above the top panel of the unit to prevent

fire and damage.

6. The voltage used must be the same as that specified on this unit.

Using this unit with a higher voltage than specified is dangerous

and may result in fire or other accidents. YAMAHA will not be held

responsible for any damage resulting from use of this unit with a

voltage other than specified.

7. Digital signals generated by this unit may interfere with other

equipment such as tuners, receivers or TVs. Move this unit farther

away from such equipment if interference is observed.

8. Always set the VOLUME control to “– ∞” before starting the audio

source play. Increase the volume gradually to an appropriate level

after playback has been started.

9. Do not attempt to clean the unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

10.Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the unit is faulty.

11.When not planning to use this unit for long periods of time,

disconnect the AC power plug from the wall outlet.

12.To prevent lightning damage, disconnect the AC power plug and

antenna cable when there is an electrical storm.

13.Grounding or polarization – Precautions should be taken so that

the grounding or polarization of an appliance is not defeated.

14.Do not connect an audio unit to the AC outlet on the rear panel if

the equipment requires more power than the outlet is rated to

provide.

15.Voltage Selector (China and General models only)

The voltage selector on the rear panel of this unit must be set

for your local main voltage BEFORE plugging into the AC

main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

IMPORTANT

Please record the serial number of your unit in the space below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off.

This state is called the standby mode.

In this mode, this unit is designed to consume a small amount of

power.

WARNING

Do not change the IMPEDANCE SELECTOR switch setting

while the power to this unit is on, otherwise this unit may be

damaged.

IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON

SWITCH IS PRESSED:

The IMPEDANCE SELECTOR switch may not be set to either

end. If so, set the switch to either end when this unit is in the

standby mode.

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied

with this appliance, it should be cut off and an appropriate 3 pin plug

fitted. For details, refer to the instructions described below.

Note: The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live socket

outlet.

Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals

in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK. The

wire which is coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED. Making sure

that neither core is connected to the earth terminal of the three pin

plug.

CAUTION : Read this before operating your unit.

OR CORRECT SETTING.

KERS

A

B

REAR

AIN

SWITCHED

AC OUTLETS

IMPEDANCE SELECTOR

CENTER : 4

Ω

MIN. / SPEAKER

FRONT

:6

Ω

MIN. / SPEAKER

REAR

:6

Ω

MIN. / SPEAKER

MAIN A OR B

:4

Ω

MIN. / SPEAKER

A B

:8

Ω

MIN. / SPEAKER

CENTER : 8

Ω

MIN. / SPEAKER

FRONT

:8

Ω

MIN. / SPEAKER

REAR

:8

Ω

MIN. / SPEAKER

MAIN A OR B

:8

Ω

MIN. / SPEAKER

A B

:

I

6

Ω

MIN. / SPEAKER

( SURROUND )

SET BEFORE POWER ON

I00W MAX.

TOTAL

IMPEDANCE

SELECTOR

(Europe model)

3

English

7 Channel Power Amplification

Main: 100W + 100W (8Ω) RMS Output

Power, 0.02% THD, 20–20,000 Hz

Center: 100W (8Ω) RMS Output Power,

0.02% THD, 20–20,000 Hz

Rear: 100W + 100W (8Ω) RMS Output

Power, 0.02% THD, 20–20,000 Hz

Front effect:

25W + 25W (8Ω) RMS Output

Power, 0.05% THD, 1 kHz

Multi-Mode Digital Sound Field

Processing

●

Digital Sound Field Processor (DSP)

●

Dolby Digital Decoder

●

Dolby Pro Logic Surround Decoder

●

DTS Decoder

●

CINEMA DSP: Theater-like Sound

Experience by the Combination of

YAMAHA DSP Technology and Dolby

Digital, Dolby Pro Logic or DTS

●

Automatic Input Balance Control for

Dolby Pro Logic Surround

●

Test Tone Generator for Easier Speaker

Balance Adjustment

●

Speaker Output Mode Selection

Capability for the Most Suitable Use of

Your Speaker System

Others

●

“SET MENU” Mode which Provides You

with 8 Titles of Setting Changes and

Adjustments for Optimizing this Unit for

Your Audio/Video System

● BASS EXTENSION Button for Reinforcing

Bass Response

● On Screen Display Function Helpful in

Controlling This Unit

●

REC OUT Selector which is Independent of

Input Source Selection

● SLEEP Timer

●

OPTICAL and COAXIAL Digital Audio

Signal Terminals

●

6 Channel External Decoder Input for Other

Future Formats

● Video Signal Input/Output Capability

(Including S Video Connections)

●

Multi-Functional

remote controller

with

“Learning” Capability

Features

INTRODUCTION

4

Welcome to the exciting world of digital home entertainment.

This unit is one of the most complete and advanced AV

amplifier available. Some of the more advanced features may

not be familiar to you, but they are easy to use. State-of-the-art

technologies such as Dolby Digital and Digital Theater

Systems (DTS) may be new to your home, but you have

probably experienced the amazing realism they bring to feature

films in theaters around the world.

To make the listening experience even more enjoyable, this

unit includes a number of exclusive, digitally created listening

environments known as digital sound fields. Choosing a sound

field program is like transporting yourself to such venues as an

outdoor arena, a European church, or a cozy jazz club. Take

some time now to read more about these features and enjoy

the new experiences this unit brings to your home theater.

Digital Sound Field Processing

Technological advances in sound reproduction over the last 30

years have enhanced the listening experience with improved

clarity, precision and power. However, something has still been

missing: The atmosphere and acoustic ambiance of the public

venue. Our Yamaha engineers have extensively researched

the nature of sound acoustics and the way sound reflects

inside a room. We sent these engineers to famous theaters

and concert halls around the world to measure the acoustics of

those venues with sophisticated microphones. The data they

collected is used to recreate these environments in digital

sound fields. Some of these digital sound fields are created

using data measured directly at the original venue; others are

created from combinations of data to form unique

environments for specific purposes.

Of course, that only solves half of the problem. These

engineers have no way of knowing the acoustics of your

listening room, so we’ve made it possible for you to adjust the

various parameters of this data to tailor each virtual venue to

your taste. You can use these sound fields to enhance any

source and in combination with any of the following surround

sound technologies. Some are designed especially for music,

and some especially for movies.

Dolby Pro Logic Surround

Dolby Pro Logic Surround has been used in movie theaters

since the mid-seventies. It has also been available in home

entertainment systems since the late eighties and continues to

be a popular format for home theater systems. It uses four

discrete channels and five speakers to reproduce realistic and

dynamic sound effects: two main channels (left and right), a

center channel for dialog, and a rear channel for special sound

effects. The rear channel reproduces sound within a narrow

frequency range.

Most video tapes and laser discs include Dolby Pro Logic

Surround encoding as do many TV and cable broadcasts. The

Dolby Pro Logic Surround decoder built into this unit employs a

digital signal processing system that stabilizes each channel

for even more accurate sound positioning than is available with

standard analog processors.

Introduction

What’s DSP?

INTRODUCTION

5

English

Dolby Digital is the next level of Dolby Surround sound system

developed for 35 mm film-movies by employing low bit-rate

audio coding.

Dolby Digital is a digital surround sound system that provides

completely independent multi-channel audio to you. Dolby

Digital provides five full range channels in what is sometimes

referred to as a “3/2” configuration: three front channels (left,

center and right), and two surround channels. A sixth bass-only

effect channel is also provided for output of LFE (low frequency

effect), or low bass effects that are independent of other

channels. (This is called the “subwoofer channel” or “LFE

channel”.) This channel is counted as 0.1, thus giving rise to

the term 5.1 channels in total.

Compared to Dolby Pro Logic that is referred to a “3/1” system

(left front, center, right front and just one surround channel),

Dolby Digital features two surround channels, called stereo or

split surrounds, each offering the same full range fidelity as the

three front channels.

By using the built-in Dolby Digital decoder, you can experience

the dramatic realism and impact of Dolby Stereo Digital theater

sound in your home.

Wide dynamic range of sound reproduced by the five full range

channels and precise sound orientation by the digital sound

processing presents listeners much excitement and realism

that has never been experienced before.

Dolby Digital forms 5.1 channels as mentioned left, and

moreover, it can also form fewer channels, for example 2

channel stereo and monaural. You may be able to find some 2

channel stereo and/or monaural sources encoded with Dolby

Digital in the market.

Laserdisc and DVD are home audio formats that could benefit

from Dolby Digital. In the near future, Dolby Digital will also be

applied to DBS, CATV and HDTV. The ongoing release of

Dolby Stereo Digital theatrical films now underway will provide

an immediate source of Dolby Digital encoded video software.

Manufactured under license from Dolby Laboratories Licensing

Corporation. “DOLBY”, “AC-3”, “Pro Logic”, and the double-D

symbol are trademarks of Dolby Laboratories Licensing

Corporation.

DTS (Digital Theater Systems) system was developed to

replace analog soundtracks of movies with six discrete

channels of digital soundtracks, and now, it is installed in many

theaters around the world. The DTS digital playback system

changed the way we experienced movies in theaters with six

discrete channels of superb digital audio.

The DTS technology, through intense research and

development, made it possible to deliver a similar

encode/decode discrete technology to home audio surround-

sound entertainment.

The DTS Digital Surround is an encode/decode system which

delivers six channels of master-quality, 20-bit audio; technically

5.1 channels, which means 5 full-range (left, center, right and

two surround) channels, plus a subwoofer (LFE) channel (as

“0.1”). It is compatible with the 5.1 speaker configurations that

are currently available for home theater systems

The DTS Digital Surround algorithm is designed to encode the

six channels of 20-bit audio onto some laserdiscs, compact

discs and DVDs with considerably less data-compression.

By using the DTS decoder built into this unit, you can

experience the dramatic realism and impact of the DTS

installed theater’s high quality sound in your home.

Laserdisc, compact disc and DVD are home audio format

within which DTS can represent its high quality multi-channel

audio. (In addition to movies on laserdiscs, many exciting new

multi-channel music recordings will also become available in

the form of DTS-encoded compact discs.)

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued

and pending. “DTS”, “DTS Digital Surround”, are trademarks of

DTS Digital Surround

Dolby Digital

INTRODUCTION

6

Dolby Pro Logic + 2 Digital Sound Fields

Digital sound fields are created on the presence side and

the rear surround side of the Dolby Pro Logic Surround-

decoded sound field respectively. They create a wide

acoustic environment and emphasize surround-effect in the

room, letting you feel much presence as if you were

watching a movie in a popular Dolby Stereo theater.

This combination is available when the digital sound field

program No. 8, 9, 10, 11 or “PRO LOGIC/Enhanced” of No.

12 is selected, and the input signal of the source is analog,

PCM audio or encoded with the Dolby Digital in 2-channels.

Dolby Digital or DTS + 3 Digital Sound Fields

Digital sound fields are created on the presence side and

the independent left and right surround sides of the Dolby

Digital-decoded or the DTS-decoded sound field

respectively. They create a wide acoustic environment and

much surround effect in the room without losing high

channel separation. With wide dynamic range of Dolby

Digital or DTS sound, this sound field combination lets you

feel as if you were watching a movie in the newest Dolby

Stereo Digital theater or DTS installed theater. This is the

most ideal home theater sound at the present time.

This combination is available when the digital sound field

program No. 8, 9, 10, 11 or “DOLBY DIGITAL (or DTS

DIGITAL SUR.)/Enhanced” of No. 12 is selected, and the

input signal of the source is encoded with the Dolby Digital

(except in 2-channels) or encoded with the DTS.

CINEMA DSP: Dolby Surround + DSP / DTS + DSP

The Dolby Surround sound and DTS systems show their full

ability in a large movie theater, because movie sounds are

originally designed to be reproduced in a large movie theater

that uses a multitude of speakers. Trying to create a sound

environment similar to that of a movie theater in your home is

difficult because of the room size, material inside the walls, the

number of speakers, and so on. In other words, your listening

room is very different from a movie theater.

However, Yamaha DSP technology allows you to create nearly

the same sound experience as that of a large movie theater in

your home by compensating for the lack of presence and

dynamics in the listening room with original digital sound fields

combined with Dolby Surround or DTS Digital Surround

sounds.

The YAMAHA “CINEMA DSP” logo indicates those programs

that are created by the combination of YAMAHA DSP

technology and Dolby Surround or DTS.

CINEMA DSP

INTRODUCTION

7

English

GETTING STARTED

Getting started

Remote controller User function stickers

Batteries (size AA, LR6, UM-3)

Unpacking

Carefully remove this unit and accessories from the box. You should find the unit itself and the following accessories.

Close the front cover whenever the controls inside the panel are not used.

To open the front cover

Opening and closing the front cover

To close the front cover

8

Installing batteries in the remote

controller

Since the remote controller will be used for many of this unit’s

control operations, you should begin by installing the supplied

batteries.

1. Turn the remote controller over and slide the battery

compartment cover in the direction of the arrow.

2. Insert the batteries (AA, LR6, UM-3 type) according to the

polarity markings on the inside of the battery compartment.

3. Close the battery compartment cover.

4. After the batteries are inserted, press the RESET button

before using the remote controller.

Notes about the remote controller

Battery replacement

If you find that the remote controller must be used closer to the

main unit, the batteries are weak. Replace both batteries with

new ones.

Notes

●

Use only AA, R6, UM-3 batteries.

(It is recommended to use an LR6 type to use the remote

controller for a long period of time.)

●

Be sure the polarities are correct. (See the illustration inside

the battery compartment.)

●

Remove the batteries if the remote controller is not used for

an extended period of time.

●

If batteries leak, dispose of them immediately. Avoid

touching the leaked material and contact with clothing, etc.

Clean the battery compartment thoroughly before installing

new batteries.

Remote controller operation range

Notes

●

The area between the remote controller and the main unit

must be clear of large obstacles.

●

Do not expose the remote control sensor to strong lighting,

in particular, an inverter type fluorescent lamp. Otherwise,

the remote controller may not work properly. If necessary,

position the main unit away from direct lighting.

1

3

2

RESET button

30°

Remote control

sensor

Within approximately

6 m (19.7 feet)

GETTING STARTED

9

English

Controls and their functions

Front panel

NATURAL SOUND AV AMPLIFIER DSP A2

CINEMA DSP

7ch

VOLUME

INPUT SELECTOR

INPUT MODE

l6

20

28

40

60

l2

8

4

2

0

–dB

PHONES

BASS

EXTENSION

BASS TREBLE BALANCE

TONE

BYPASS

VCR 2

VIDEO AUX

REC OUT

VCR 1

TV/DBS

PHONO

TUNER

CD

DVD/LD

SOURCE

TAPE/MD

VIDEO AUX

NEXT EFFECT PROGRAM

A

SPEAKERS

B

SET MENU

EXT. DECODER

STANDBY/ON

55

4

3

2

l

0

l

2

3

4

LR

55

4

3

2

l

0

l

2

3

4

55

4

3

2

l

0

l

2

3

4

A

1

D F HBI

23 4

5

6

87 9 0 C EG

1 STANDBY/ON switch

Press this switch to turn on the power. Press this switch again

to set this unit in the standby mode.

* A click from the switch and the initial rotation of the built-in

fan will be heard when the power is turned on.

Standby mode

This unit is still using a small amount of power in this mode

in order to be ready to receive infrared-signals from the

remote controller.

2 Remote control sensor

Receives signals from the remote controller.

3 Display panel

Displays a variety of information. (Refer to page 11 for details.)

4 INPUT MODE button

Press this button to select how input signals are received from

sources that output two or more types of signals. The “AUTO”,

“DTS” and “ANALOG” modes are available. The “AUTO”,

“D.D.RF”, “DTS”, “DGTL” and “ANALOG” modes are available

for DVD/LD sources. Refer to page 35 for details.

5 INPUT SELECTOR

Turn this knob to select the input source.

The selected source will be shown on the display.

6 Master VOLUME control

Simultaneously controls volume for all output sounds; front

effect, main, rear, center and subwoofer. (The REC OUT level

is not affected.)

* The indicator on the master VOLUME control will flash when

the volume is decreased by pressing the MUTE key on the

remote controller.

For the remote controller, refer to pages 60 to 61.

GETTING STARTED

10

7

SPEAKERS switches

Press the switch A or B (or both) for the main speakers you will

use to select them. Press the switch for the main speakers you

will not use again to cancel them. On the display panel,

“SPEAKERS A” and/or “SPEAKERS B” will be illuminated,

depending on which main speakers are being selected.

8 PHONES jack

Headphones can be plugged into this jack for private listening.

You can listen to the sound to be output from the main

speakers through headphones. When listening with

headphones privately, press both SPEAKERS A and B

switches to cancel both of the main speakers A and B, and turn

off the digital sound field processor by pressing the EFFECT

button so that no DSP program name is illuminated on the

display panel.

9 BASS EXTENSION button

Press this button inward (ON) to boost the bass frequency

response at the main left and right channels while maintaining

overall tonal balance. This function is effective for reinforcing

the bass frequencies when a subwoofer is not used.

0 TONE BYPASS button

Press this button inward (ON) to bypass the tone (BASS and

TREBLE) control circuitry. This function is used for outputting

pure sound and checking the tone control settings. The tone

control circuitry can be used when this button is released

outward (OFF).

A SET MENU –/+ button

Press this button once or more to make a setting change or

adjustment for the function selected by pressing the NEXT

button.

NEXT button

Press this button once or more to select a function in the SET

MENU mode.

B BASS and TREBLE controls

Rotate these knobs to adjust the low and high frequency

response for the left and right main channels only.

C EXT. DECODER button

Press this button to select the input signals from the

EXTERNAL DECODER INPUT terminals as the input source.

This function takes priority over the INPUT SELECTOR setting.

“EXT. DECODER IN” will be illuminated on the display panel.

The source selected with the INPUT SELECTOR knob

becomes the current input source when “EXT. DECODER IN”

is not illuminated on the display panel.

D BALANCE control

This knob controls the sound from the main speakers only.

The balance of the output volume to the left and right main

speakers can be adjusted to compensate for sound imbalances

caused by the speaker location or listening room conditions.

E EFFECT button

Press this button to turn on and off the output from the center,

rear and front effect speakers. The sound becomes normal 2-

channel when this function is turned off.

However, this does not apply to Dolby Digital or DTS. The

signals at all channels will be distributed to the main channels

and output from the main speakers, even if the output from the

center, rear and front effect speakers are turned off, when

Dolby Digital or DTS is decoded.

F REC OUT selector

Rotate this knob to select the source for recording to an MD

recorder (or tape deck) or VCR. This setting is independent of

the INPUT SELECTOR setting, except when the REC OUT

selector is set to the SOURCE position. Then the INPUT

SELECTOR is used to select the source for recording to the

MD recorder (or tape deck) or VCR.

G PROGRAM selector button

Press this button in the or direction to select a digital

sound field processing program.

H VIDEO AUX terminals

Connect an auxiliary video or audio input source unit such as a

camcorder to these terminals. A video unit with a S video

output terminal can be connected to the S VIDEO terminal to

obtain a high resolution picture. The source can be selected

with the INPUT SELECTOR and REC OUT selector.

I Front cover

Refer to page 7 on how to open and close the front cover.

PHONES

GETTING STARTED

11

English

Display panel

DIGITAL

PRO LOGIC

DSP

SPEAKERS

AB

TAPE/MD

CD

TUNER

PHONO

DVD/LD

TV/DBS

VCR 1

VCR 2

V-AUX

SLEEP

2 31

546 7

1 indicators

Either of the “dts” indicators will be illuminated when the built-in

DTS decoder is turned on.

A red “dts” indicator will be illuminated when playing a compact

disc or laserdisc encoded with DTS.

An orange “dts” indicator will be illuminated when playing a

DVD encoded with DTS.

An orange “dts” indicator may be illuminated when playing a

laserdisc encoded with DTS after a video-CD or DVD on a

DVD/LD combi-player.

2 Multi-information display

This display shows the current DSP program and the status of

adjustments and setting changes. Several statuses can be

viewed at one time.

3 Input source indicators

One of the arrows for these indicators will be illuminated

depending on which source is selected.

4 DIGITAL and PRO LOGIC indicators

The DIGITAL indicator will be illuminated when the built-in

Dolby Digital decoder is on and the signals of the source

encoded with Dolby Digital are not 2-channels.

The PRO LOGIC indicator will be illuminated when the

built-in Dolby Pro Logic Surround Decoder is on.

5 DSP indicator

This indicator will be illuminated when the built-in digital sound

field processor is on.

6 SPEAKERS A/B indicators

One of these indicators will be illuminated depending on which

main speakers are selected. Both indicators will be illuminated

when both speakers A and B are selected.

7 SLEEP indicator

This indicator will be illuminated when the built-in SLEEP timer

is on.

GETTING STARTED

12

This unit has been designed to provide the best sound field

quality with a full seven-speaker system setup, using a pair of

main speakers to output main source sounds, two extra pairs

of effect speakers to generate the sound field plus one center

speaker for dialog. We therefore recommend that you use a

seven-speaker setup. A four-speaker system using only one

pair of effect speakers for the sound field will still provide

impressive ambience and effects, however, and may be a

good way to begin with this unit. You can always upgrade to

the full seven-speaker system later. In the 4 or 5 speaker

system, the Digital Sound Field Processing is still performed,

but the main speakers are used for both the main channels

and the front effect channels.

Use of the center dialog speaker is

recommended

When playing back a source with Dolby Pro Logic decoded, or

playing back a source which contains center-channel signals

with Dolby Digital or DTS decoded, dialog, vocals etc. are

output from the center channel. Therefore, if you want to

maximize the performance of your Audio/Video home theater

system, it is recommended that you use a center channel

speaker.

If, for some reason, it is not practical to use a center speaker, it

is possible to enjoy the movie without it. Best results, however,

are obtained with the full system.

Use of a subwoofer expands your sound

field

It is also possible to further expand your system with the

addition of a subwoofer and amplifier. The use of a subwoofer

is effective not only for reinforcing bass frequencies from any

or all channels, but also for reproducing signals at the

subwoofer channel with high fidelity during playing back a

source with Dolby Digital or DTS decoded. You may wish to

choose the convenience of a Yamaha Active Servo Processing

Subwoofer System, which has its own built-in power amplifier.

Speaker setup

m Speakers and speaker placement

Your full seven-speaker system will require three speaker

pairs: the MAIN SPEAKERS (your normal stereo speakers),

the FRONT EFFECT SPEAKERS and the REAR SPEAKERS,

plus the CENTER SPEAKER. You may also be using a

SUBWOOFER.

The MAIN SPEAKERS should be high performance models

and have enough power handling capacity to accept the

maximum output of your audio system.

Other speakers do not have to be equal to the MAIN

SPEAKERS. For precise sound localization, however, it is

ideal to use high performance models that can reproduce

sounds in full range for the CENTER SPEAKER, the FRONT

EFFECT and REAR SPEAKERS.

Place the MAIN SPEAKERS in the ordinary position.

Place the FRONT EFFECT SPEAKERS further apart than the

MAIN SPEAKERS, on either side of and 0.5–1m behind and

above the MAIN SPEAKER pair.

Place the REAR SPEAKERS behind your listening position.

They should be nearly 1.8m above the floor.

Place the CENTER SPEAKER precisely between the two

MAIN SPEAKERS. (To avoid interference, keep the speaker

above or below the television monitor, or use a magnetically

shielded speaker.)

If using a SUBWOOFER, such as a Yamaha Active Servo

Processing Subwoofer System, the position of the speaker is

not so critical because low bass tones are not highly

directional.

m Setting up your speaker system

Main speaker

Front effect speaker

Center speaker

Rear speaker

Subwoofer

PREPARATION

13

English

4 Speaker System

Basic system.

You can enjoy widely diffused sound by only adding a pair of

rear speakers to a basic stereo speaker system.

1E. SYS. SETUP—Set to 5ch. (See page 27.)

1A. CENTER SP—Set to NONE. (See page 26.)

6 Speaker System

Good for sound fields from 2-channel stereo sources.

When a normal stereo source is played back with the sound

field programs No. 1 through No. 7, a sound effect matching

that of a 7-speaker system can be obtained. The addition of

front left and right effect speakers produces a more effective

sound field.

1E. SYS. SETUP—Set to 7ch. (See page 27.)

1A. CENTER SP—Set to NONE. (See page 26.)

5 Speaker System

Good for Audio/Video sources.

By the use of a center speaker, center sounds (dialog, vocals

etc.) are precisely localized.

1E. SYS. SETUP—Set to 5ch. (See page 27.)

1A. CENTER SP—Set to LRG or SML. (See page 26.)

7 Speaker System

This is the recommended speaker system, providing the

best sound effects.

The rear speakers and the front effect speakers produces a

360-degree sound field, and the center speaker provides

precise center localization.

You can experience the amazing YAMAHA “CINEMA DSP”

sound fields completely with the 7 speaker system.

1E. SYS. SETUP—Set to 7ch. (See page 27.)

1A. CENTER SP—Set to LRG or SML. (See page 26.)

m Recommended speaker system configurations

PREPARATION

14

Caution: Plug in this unit and other components after all connections are completed.

All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for

each of your components.

Audio/video source equipment

●

Use RCA type pin plug cables for audio/video units with the exception described later.

●

The output (or input) terminals of YAMAHA audio/video units numbered as 1, 2, 3, 4, etc. on the rear panel must be

connected to the same-numbered terminals of this unit.

VIDEO

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

TUNER

VCR 2

OUT

VIDEO

S VIDEO

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

VCR 2

OUT

MONITOR

OUT

S VIDEO

AUDIO SIGNAL VIDEO SIGNAL

EXTERNAL DECODER INPUT

2

MAIN

SUB WOOFER

CENTER

SURROUND

TV/DBS

CD

DVD/LD

TAPE/MD

IN

(PLAY)

OUT

(REC)

DVD/LD

COAXIAL

OPTICAL

DIGITAL

RF SIGNAL

DIGITAL SIGNAL

GND

PHONO

1

CD

TAPE/MD

3

4

IN

( PLAY )

OUT

( REC )

AUDIO SIGNAL

OUTPUT

GND

OUTPUT

LINE OUT

LINE IN

(Europe model)

Turntable

MD recorder,

Tape deck, etc.

CD player

Tuner

m Basic connections of audio units

(*1): GND terminal (For turntable use)

Connecting the ground wire of the turntable to the GND

terminal will normally minimize hum, but in some cases

better results may be obtained with the ground wire

disconnected.

: Indicates the direction of signals.

Connections

PREPARATION

(*1)

15

English

VIDEO

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

TUNER

VCR 2

OUT

VIDEO

S VIDEO

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

VCR 2

OUT

MONITOR

OUT

S VIDEO

AUDIO SIGNAL

EXTERNAL DECODER INPUT

2

MAIN

SUB WOOFER

CENTER

SURROUND

TV/DBS

CD

DVD/LD

TAPE/MD

IN

(PLAY)

OUT

(REC)

DVD/LD

COAXIAL

OPTICAL

DIGITAL

RF SIGNAL

DIGITAL SIGNAL

GND

PHONO

1

CD

TAPE/MD

3

4

IN

( PLAY )

OUT

( REC )

AUDIO SIGNAL VIDEO SIGNAL

VIDEO IN

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO IN

VIDEO IN

AUDIO IN

VIDEO IN

AUDIO OUT

VIDEO OUT

(Europe model)

LD player or

DVD player

TV monitor

m Basic connections of video units

Video cassette

recorder 2

Video cassette

recorder 1

TV/Satellite tuner

PREPARATION

VIDEO AUX terminals (on the front panel)

These terminals are used to connect a video input source such as a camcorder.

VIDEO AUX

S VIDEO

L

R

VIDEO

VIDEO OUT

S VIDEO OUT

AUDIO OUT L

AUDIO OUT R

Camcorder

: S-video cable

(Refer to page 19 for details

about the S VIDEO terminal.)

16

(Europe model)

No connection

TV monitor

Scart-plug connector

cable

MAIN

PRE

OUT

MAIN

IN

COUPLER

IN

TUNER

VCR 2

OUT

VIDEO

S VIDEO

IN

VCR 2

OUT

MONITOR

OUT

EXTERNAL DECODER INPUT

2

MAIN

SUB WOOFER

CENTER

SURROUND

TV/DBS

TAPE/MD

IN

(PLAY)

OUT

(REC)

DVD/LD

DIGITAL SIGNAL

VIDEO

AUDIO L

AUDIO R

For connecting with a TV monitor that uses a 21 pin

connector for input (Europe and U.K. models only)

Make a connection as figured below with a commercially

available scart-plug connector cable.

PAL/NTSC switch (China and General models only)

This unit is designed for use with the NTSC and PAL television

formats. Set this switch to the position for the format your TV

monitor employs.

PAL: Set to this position if your TV monitor employs the

PAL format.

* Outputs signals in the PAL format no matter which

format (PAL or NTSC) of video signal is sent from

an external video unit to this unit.

NTSC: Set to this position if your TV monitor employs the

NTSC format.

* Outputs signals in the NTSC format no matter which

format (PAL or NTSC) of video signal is sent from

an external video unit to this unit.

Note

Be sure to input a video signal which employs the same format

that your TV monitor employs, otherwise a picture will not be

played back normally.

CAUTION

IN

VCR 1

OUT

IN

VCR 2

PAL

NTSC

PAL/NTSC switch

PREPARATION

17

English

PREPARATION

Notes

●

When you connect an audio/video unit to both of the digital

and analog terminals of this unit, make sure to connect to

both terminals of the same name.

●

Be sure to attach the covers when the OPTICAL terminals

are not being used, in order to protect the terminals from

dust.

●

In order to make this unit perform successful DTS-decoding,

the DTS bitstream must not be altered, manipulated or

corrupted in the process of sending the DTS bitstream from

the DIGITAL OUT terminal of an external unit to a digital

signal input terminal of this unit.

●

All digital audio signal input terminals are applicable to the

sampling frequency of 32 kHz, 44.1 kHz and 48 kHz.

: Optical fiber cable

: Coaxial cable

VIDEO

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

TUNER

VCR 2

OUT

VIDEO

S VIDEO

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

VCR 2

OUT

MONITOR

OUT

S VIDEO

AUDIO SIGNAL VIDEO SIGNAL

EXTERNAL DECODER INPUT

2

MAIN

SUB WOOFER

CENTER

SURROUND

TV/DBS

CD

DVD/LD

TAPE/MD

IN

(PLAY)

OUT

(REC)

DVD/LD

COAXIAL

OPTICAL

DIGITAL

RF SIGNAL

DIGITAL SIGNAL

GND

PHONO

1

CD

TAPE/MD

3

4

IN

( PLAY )

OUT

( REC )

AUDIO SIGNAL

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL IN

MD recorder, DAT,

etc.

CD player

TV/Satellite tuner

LD player or DVD player

(Europe model)

m Connecting to digital (OPTICAL and COAXIAL) terminals

If your CD player, MD recorder, LD player, DVD player,

TV/satellite tuner, etc. are equipped with coaxial or optical

digital audio signal output terminals, they can be connected to

this unit’s COAXIAL or OPTICAL, or both terminals.

Digital audio signals are transmitted with less loss than analog

audio signals. In addition, digital audio signal connections are

necessary, especially for an LD player, a DVD player or a CD

player to send signals encoded with Dolby Digital or DTS to

this unit.

To make an optical digital connection between this unit and an

external unit, remove the cover from each optical terminal, and

then connect them by using a commercially available optical

fiber cable that conforms to EIAJ standards. Other cables

might not function correctly.

Even if you connect an audio/video unit to the OPTICAL (or

COAXIAL) terminal of this unit, you must keep the unit

connected with the same named analog audio signal terminals

of this unit, because digital signal cannot be recorded by a tape

deck or VCR connected to only analog audio signal terminals

of this unit. You can switch the selection of input signals

between “digital” and “analog” easily. (See page 35 for details.)

* However, if you connect an MD recorder or DAT to this

unit’s OPTICAL TAPE/MD IN and OUT terminals, it can

record input sources connected to this unit’s OPTICAL

digital signal input terminals.

18

DVD/LD

TV/DBS

IN

VCR 1

OUT

IN

TUNER

VCR 2

OUT

AUDIO SIGNAL

EXTERNAL DECODER INPUT

2

MAIN

SUB WOOFER

CENTER

SURROUND

TV/DBS

CD

DVD/LD

TAPE/MD

IN

(PLAY)

OUT

(REC)

DVD/LD

COAXIAL

OPTICAL

DIGITAL

RF SIGNAL

DIGITAL SIGNAL

GND

PHONO

1

CD

TAPE/MD

3

4

IN

( PLAY )

OUT

( REC )

AUDIO SIGNAL

DIGITAL OUT

ANALOG OUT

DOLBY DIGITAL

RF OUT

(Europe model)

PREPARATION

If your DVD/LD/CD combi-player has a DOLBY DIGITAL RF

signal output terminal, connect it to this unit’s DIGITAL RF

SIGNAL input terminal. Audio signals of an LD source encoded

with the Dolby Digital are input to this unit by this connection.

* To play back an LD source with the Dolby Digital decoded,

set the input mode of DVD/LD to “AUTO” or “D.D.RF”.

(Refer to page 35 for details.)

It is also necessary to connect the DVD/LD/CD combi-player to

this unit’s analog audio signal input terminals regardless of the

DOLBY DIGITAL RF signal connection. This is for playing back

a source with Dolby Pro Logic Surround decoded or in normal

stereo (or monaural).

You must also connect the optical digital signal output terminal

of the DVD/LD/CD combi-player to the OPTICAL DVD/LD

digital signal input terminal of this unit.

This connection is necessary for playing back a DVD source

with Dolby Digital or DTS decoded, and playing back an LD

source with DTS decoded.

Note

DOLBY DIGITAL RF audio input signal cannot be recorded by

a tape deck, MD recorder or VCR. To record a source played

back on the DVD/LD/CD combi-player, it must be connected to

the OPTICAL digital audio signal input terminal and analog

audio signal input terminals of this unit.

m Connecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player

DVD/LD/CD

combi-player

Pagina se încarcă ...

Yamaha DSP-A2 Manualul proprietarului

Yamaha DSP-A2 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente