Husqvarna G1300P Manual de utilizare

G1300P, G2500P, G3200P, G5500P, G8500P

EN Operator's manual 2-18

BG Ръководство за експлоатация 19-38

CS Návod k použití 39-56

EL Οδηγίες χρήσης 57-75

ES Manual de usuario 76-94

FR Manuel d'utilisation 95-113

HU Használati utasítás 114-131

IT Manuale dell'operatore 132-149

PL Instrukcja obsługi 150-168

PT Manual do utilizador 169-186

RO Instrucţiuni de utilizare 187-204

SK Návod na obsluhu 205-222

TR Kullanım kılavuzu 223-239

Contents

Introduction..................................................................... 2

Safety..............................................................................5

Assembly........................................................................ 8

Installation.......................................................................8

Operation........................................................................ 9

Maintenance................................................................. 10

Troubleshooting............................................................ 13

To prepare the product for long-term storage...............14

Technical data.............................................................. 15

EC Declaration of Conformity....................................... 18

Introduction

Product description

This product is a portable generator with a combustion

engine.

Intended use

The product supplies electrical power to operate

electrical loads in locations where there is no electrical

power available. Do not use the product for other tasks.

Product overview

12

3

4

5

6

9

8

7

10

11

15

14

7

13

12

1. Fuel valve

2. Choke

3. Air filter

4. Starter rope handle

5. Wheel

6. Battery

7. Power switch

8. Handle

9. Frame

10. Fuel gauge

11. Fuel tank cap

12. AC circuit breakers

13. VFT meter

14. Ground terminal

15. AC receptacle

21420 - 004 - 14.02.2022

12 V DC terminal

The 12 V DC terminal is a power source for 12 V DC

units.

VFT meter

The VFT meter shows the voltage, frequency and total

operation time of the product.

V

F

T

AC receptacles

The product has several AC receptacles to give power

to tools and equipment. The AC receptacles are different

in different market areas.

EU, 1-phase, 50 Hz

A: 2-Prong, 230 V receptacle.

B: 3-Prong, 32 A 230 V receptacle.

A B

US, 1-phase, 60 Hz

A: 3-Prong, duplex 120 V receptacle.

B: 4-Prong, twist lock 30 A 120/240 V receptacle.

C: 4-Prong, 50 A 120/240 V receptacle.

A B C

US, 3-phase, 60 Hz

A: 3-Prong, duplex 110 V receptacle.

B: 5-Prong, 3-phase 127/220 V receptacle.

A

B

CN, 1-phase, 50 Hz

A: 3-Prong, twist lock, 230 V receptacle.

A

1420 - 004 - 14.02.2022 3

Symbols on the product

WARNING! Be careful and use the

product correctly. This product can cause

serious injury or death to the operator or

others.

Read the operator's manual carefully

and make sure you understand the

instructions before you use this product.

Risk of fire or explosion.

Risk of carbon monoxide poisoning. Do

not operate the product in areas with bad

airflow.

Risk of electrical shock.

Risk of burn injury.

Add oil.

Add fuel.

Open the fuel valve.

Set the power switch to the ON position.

Set the choke to the OFF position.

Set the choke to the ON position.

Pull the starter rope handle.

Connect the electrical loads.

Disconnect the electrical loads.

Close the fuel valve.

Noise emissions to the environment

according to European Directive

2000/14/EC and New South Wales

legislation “Protection of the Environment

Operations (Noise Control) Regulation

2017”. Noise emission data can be found

on the machine label and in the Technical

data chapter.

Do not use the product in-

doors.

Use the product outdoors.

Keep the product away

from windows, doors or

vents.

Set the choke to the ON

position and wait for 50

seconds.

Set the choke to the OFF

position and wait for 50

seconds.

Wait 30 seconds and set

the power switch to the

OFF position.

41420 - 004 - 14.02.2022

Type plate

000000000

000 00 00-00

0 00000

0000

00000

0000

Prod. year 0000

Serial No.

Product

Article No.

Model

Weight

Rated current

Max Power

COP Power

Voltage

Rated Frequency

Power factor

Performance class

Quality class

Protection class

Low-power

generating set

Husqvarna AB

SE-561 82 Huskvarna

Sweden

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of

injury or death for the operator or bystanders

if the instructions in the manual are not

obeyed.

CAUTION: Used if there is a risk of

damage to the product, other materials or

the adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary

in a given situation.

General safety instructions

WARNING: Read and understand the

warning instructions that follow before you

use the product.

• Read and understand the operator's manual and

safety decals on the product before operation. Your

safety and the safety of others is your responsibility.

• Obey the instructions in this operator's manual.

• It is not possible to give a warning for each situation

that can occur during operation and maintenance

of this product. Always be careful and use your

common sense.

Fuel safety

WARNING: Read and understand the

warning instructions that follow before you

use the product.

• Gasoline is highly flammable and its vapors are

explosive. Do not permit smoking, open flames,

sparks or heat in the vicinity while handling gasoline.

• Never add fuel while the product is running or hot.

Allow the engine to cool completely before adding

fuel.

• Never fill the fuel tank indoors.

• Comply with all laws regulating storage and handling

of gasoline.

• Do not overfill the fuel tank. Always allow room for

fuel expansion. If the fuel tank is over-filled, fuel can

overflow onto a hot engine and cause a fire or an

explosion.

• Never store the product with fuel in the fuel tank

where gasoline vapors might reach an open flame,

spark or pilot light (as on a furnace, water heater

or clothes dryer). Fire or explosion may result. Allow

the product to cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure

that no combustible materials are left on or near

the product. Keep the area surrounding the product

clean and free from debris. Keep a clearance of 5

ft. on all sides to allow for proper ventilation of the

product.

• Do not operate the product if a connected electrical

device overheat, if the electrical output is lost, or if

flames or smoke are observed while the product is

running.

• Keep a fire extinguisher near the product at all times.

• Avoid spilling fuel on a hot engine.

1420 - 004 - 14.02.2022 5

• Do not smoke or light cigarettes near the product or

fuel.

• Drain fuel into an approved container outdoors, away

from open flame. make sure that the engine is cool.

Exhaust safety

WARNING: Read and understand the

warning instructions that follow before you

use the product.

• Never operate the product in an enclosed area or

indoors! Never use the product in the home, in a

vehicle, or in partly enclosed areas such as garages,

even if doors and windows are open! Only use the

product outdoors and far from open windows, doors,

vents, and in an area that will not accumulate deadly

exhaust.

• The engine exhaust fumes contain carbon

monoxide, which you cannot see or smell.

This poisonous gas, if breathed in sufficient

concentrations, can cause unconsciousness or even

death.

• Adequate, unobstructed flow of cooling and

ventilating air is critical for correct product operation.

Do not alter the installation or permit even partial

blockage of ventilation provisions, as this can

seriously affect safe operation of the product. The

product must be operated outdoors.

• Always use a battery-operated carbon monoxide

alarm indoors, installed according to the

manufacturers instructions.

• If you start to feel sick, dizzy, or weak after

the product has been running, move to fresh air

immediately. See a doctor, as you could have

carbon monoxide poisoning.

Electrical safety

WARNING: Read and understand the

warning instructions that follow before you

use the product.

• The product produces dangerously high voltage

when in operation. Avoid contact with bare wires,

terminals, connections, etc., while the product is

running, even on equipment connected to the

product. Ensure that all appropriate covers, guards

and barriers are in place before operating the

product.

• Never handle any kind of electrical cord or device

while standing in water, while barefoot or while

hands or feet are wet. Dangerous electrical shock

can occur.

• Some countries may require the frame and external

electrically conductive parts of the product be

properly connected to an approved earth ground.

Some countries may also require proper grounding

of the product. Consult with a local electrician for

grounding requirements in the area.

• Use a ground fault circuit interrupter (GFCI) in any

damp or highly conductive area (such as metal

decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged

electrical cord sets with the product.

• In case of accident caused by electric shock,

immediately shut down the source of electrical

power. If this is not possible, attempt to free the

victim from the live conductor. Avoid direct contact

with the victim. Use a non-conducting implement,

such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first

aid and get immediate medical help.

Safety instructions for operation

WARNING: Read and understand the

warning instructions that follow before you

use the product.

• Only operate the product on level surfaces and

where it will not be exposed to excessive moisture,

dirt, dust or corrosive vapors.

• Keep hands, feet, clothing, etc., away from drive

belts, fans, and other moving parts. Never remove

any fan guard or shield while the unit is operating.

• Certain parts of the generator get extremely hot

during operation. Keep clear of the generator until

it has cooled to avoid severe burn injuries.

• Do not operate the product in rain.

• Do not alter the construction of the product or

change controls which might create an unsafe

operating condition.

• Never start or stop the product with electrical

loads connected to receptacles and with connected

devices turned on. Start the engine and let it stabilize

before connecting electrical loads. Disconnect all

electrical loads before shutting down the generator.

• Do not insert objects through the cooling slots of the

product, even if the engine is not running.

• When working on this equipment, remain alert at all

times. Never work on the equipment when physically

or mentally fatigued.

• Never use the product or any of its parts as

a step. Stepping on the product can stress and

break parts, and may result in dangerous operating

conditions from leaking exhaust gases, fuel leakage,

oil leakage, etc.

• Make sure that you have knowledge about all

controls and adjustments before operation.

• Do not overload the product. Also, do not overload

individual panel receptacles. These outlets are

protected against overload with circuit breakers. If

amperage rating of any circuit breaker is exceeded,

that breaker opens and electrical output to that

receptacle is lost.

• Never start or stop engine with electrical devices

plugged into the receptacles and devices turned on.

61420 - 004 - 14.02.2022

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not use a product with defective safety devices.

• Do a check of the safety devices regularly. If

the safety devices are defective, speak to your

Husqvarna service agent.

Power switch

Use the power switch to start and stop the engine.

I

O

Circuit breakers

The circuit breakers prevents overload in the product.

Information about rated value of the circuit breaker is

shown near the circuit breaker.

Ground terminal

The ground terminal makes sure that the product is

correctly grounded. Before each operation, a ground

wire must be connected to the ground terminal.

Safety instructions for maintenance

WARNING: Read and understand the

warning instructions that follow before you

do maintenance on the product.

• For safety reasons, the manufacturer recommends

that the maintenance of this equipment is carried

out by an Authorized Dealer. Inspect the generator

regularly, and contact the nearest Authorized Dealer

for parts needing repair or replacement.

• This product is equipped with a muffler that has

a spark arrester. The spark arrester must be

maintained in effective working order by the owner/

operator.

• The exhaust system must be properly maintained.

Do nothing that might make the exhaust system

unsafe or non-compliant with local codes and/or

standards.

• Before performing maintenance on the product,

disconnect the engine starting battery (if equipped)

to prevent accidental start up. Disconnect the cable

from the battery terminal indicated by a negative,

NEG or (–) first. Reconnect that cable last.

• Any attempt to crank or start the engine before it

has been properly serviced with the recommended

oil may result in engine failure.

• When working on the product, always disconnect the

spark plug cap from spark plug and keep the spark

plug cap away from the spark plug.

• Hot oil may cause burns. Allow engine to cool

before draining oil. Avoid prolonged or repeated skin

exposure to used oil. Thoroughly wash exposed

areas with soap.

• The warranty of the product does not cover items

that have been subjected to operator abuse of

negligence. To receive full value from the warranty,

the operator must maintain the product as instructed

in this operator's manual.

1420 - 004 - 14.02.2022 7

Assembly

Introduction

WARNING: Read and understand the

safety chapter before you assemble the

product.

To assemble the accessory kit

(G5500P, G8500P)

1. Learn the parts of the accessory kit.

G

A

B

C

D

F

E

X2

HX2

IX4

JX2

KX2

LX2

MX2

NX2

2. Assemble the accessory kit. Refer to the illustrations.

a) Wheel assembly:

H

I

G

A

b) Handle assembly:

K

C

L

J

B

N

F

M

E

D

Installation

Introduction

WARNING: Read and understand the

safety chapter before you install the product.

To ground the product

WARNING: The product must be

grounded by a person with good experience

and knowledge in the field of electricity. In

some areas an approved electrician must do

the installation. Obey local regulations.

1. Install a ground rod at a minimum of 24 in. into the

ground.

WARNING: The ground rod must

be made of brass or copper.

2. Connect a 2.5 mm2 ground wire from the ground

terminal on the control panel to a ground rod.

Note: The ground wire and the ground rod are not

supplied with the product.

81420 - 004 - 14.02.2022

To connect the product to the electrical

system of a building

WARNING: The product must be

grounded by a person with good experience

and knowledge in the field of electricity. In

some areas an approved electrician must do

the installation. Obey local regulations.

• Use a manual transfer switch to connect the product

to an electrical system.

• Make sure that you do the procedure in compliance

with all national and local regulations.

Operation

Introduction

WARNING: Read and understand the

safety chapter before you use the product.

To fill fuel

Use unleaded gasoline. Do not use gasoline with more

than 10% ethanol and do not use E85 gasoline.

CAUTION: Do not mix gasoline with oil.

1. Stop the engine and let the product become cool.

Refer to

To stop the product on page 10

.

2. Make sure that the product is on level ground and in

an area with good airflow.

3. Remove the fuel tank cap.

4. Carefully fill the fuel tank (A). Fill fuel (B) to the mark

(C).

A B C

5. Clean the product from fuel spillage.

CAUTION: Fuel spillage is a fire

risk and can cause damage to the

environment.

To start the product

1. Disconnect all electrical loads from the receptacles

on the control panel.

2. Make sure that the product is on a level surface.

3. Open the fuel valve.

4. Set the power switch (A) to the ON position.

A

5. Set the choke to the OFF position.

6. Pull the starter rope handle slowly until you feel

resistance.

7. Pull the starter rope handle quickly and with force

until the engine starts.

8. For electric start, do the steps that follow.

a) Push and hold the ON/OFF/START key in the

start position.

b) When the engine starts, move the ON/OFF/

START key to the ON position.

9. Move the choke to ½ choke position.

10. When the engine runs smoothly, set the choke to the

ON position.

1420 - 004 - 14.02.2022 9

Note: For G1300P, the ON and OFF positions of

the choke are at the opposite positions.

To connect the electrical loads

WARNING: Do not connect 240 (230)

V to 120 (110) V receptacles. Do not

connect 3-phase electrical loads to a 1-

phase product. Do not connect 50 Hz

electrical loads to a 60 Hz product.

1. Start the engine and let it become warm for some

minutes. Refer to

To start the product on page 9

.

2. Connect and start the electrical loads.

3. Make sure that there is no overload in the product.

Refer to

To prevent overload in the product on page

10

.

To prevent overload in the product

Overload in the product can cause damage to the

product and to connected electrical devices. Do the

steps that follow to prevent overload in the product.

• Add the total amount of W of all electrical devices to

be connected at the same time.

CAUTION: The total W must not be

more than the W capacity of the product.

• The rated W of lights can be used from light bulbs.

The rated W of tools, equipment and motors can be

found on a decal on the device.

• If there is no amount of W specified in the product,

tool or equipment, multiply V with the rated A value.

• Always connect electrical devices with the highest

start up W to the product first. Then add the W of all

other connected electrical loads.

To stop the product

1. Stop and disconnect the electrical loads from the

receptacles on the control panel.

WARNING: Do not stop the engine

if the electrical loads are on and

connected to the product.

2. Let the engine operate without load for 30 seconds.

3. Set the power switch to the OFF position.

4. Close the fuel valve.

Maintenance

Introduction

WARNING: Read and understand the

safety chapter before you do maintenance

on the product.

Maintenance schedule

* Clean at a more regular interval if the product is used

in conditions with much dust.

** Maintenance must be done by an approved servicing

dealer.

Maintenance Daily

mainte-

nance

before

opera-

tion

Maintenance interval in hours

20

hours or

each

month

50

hours or

each 3

months

100

hours or

each 6

months

300

hours or

1 time

each

year

Each 2

years

Clean the product. X

Do a check of the engine oil level. X

Do a check of the air filter. X

Clean the air filter. X

Do a check of the deposit cup. X

Replace the engine oil. X*

Clean or replace the air filter. X*

Do a check of and clean the spark plug. X

10 1420 - 004 - 14.02.2022

Maintenance Daily

mainte-

nance

before

opera-

tion

Maintenance interval in hours

20

hours or

each

month

50

hours or

each 3

months

100

hours or

each 6

months

300

hours or

1 time

each

year

Each 2

years

Do a check of the idle speed. Adjust the idle speed

if it is necessary. X**

Do a check of the valve clearance. Adjust the valve

clearance if it is necessary. X**

Clean the fuel tank, fuel strainer and carburetor. X**

Clean the combustion chamber. X**

Replace the fuel lines if it is necessary. X**

To clean the product

CAUTION: Do not use water to clean

the product. Water can cause damage to the

product.

• Use a moist cloth to clean the external surfaces of

the product.

• Use a soft brush to remove dirt and oil.

• Use a vacuum cleaner to remove clean dirt and

unwanted material from the product.

• Use compressed air to remove dirt from cooling slots

and other opening on the product.

CAUTION: The pressure of the

compressed air must not be more than

25 psi.

To do a check of the engine oil level

CAUTION: Do not operate the product

with low engine oil level. It can cause

damage to the engine.

CAUTION: Use engine oil that has SJ

class, SL class, or better, from the American

Petroleum Institute (API). Do not use special

additives. Select a viscosity range that

agrees with the ambient temperature. Refer

to the illustration below.

10W-30

SAE 30

Synthetic 5W-30

1. Stop the product fully and make sure that the

product is on level ground.

2. Clean the area around the oil tank.

3. Remove the oil tank cap and dipstick.

4. Clean the oil from the dipstick.

5. Put the dipstick back fully into the oil tank.

6. Remove the dipstick.

7. Examine the engine oil level on the dipstick.

8. If the engine oil level is low, fill engine oil until the

engine oil is to the mark (A) on the dipstick. Refer to

Technical data on page 15

for the oil tank capacity.

A A

9. Do a check of the engine oil level again.

10. Install the oil tank cap and dipstick.

1420 - 004 - 14.02.2022 11

To replace the engine oil

Note: Drain the engine oil while the engine is warm.

Warm engine oil is faster to drain.

WARNING: The engine oil becomes

very hot and can cause burn injuries. Let

the engine become cool before you drain the

engine oil.

1. Clean the area around the oil drain plug (A).

B

A

2. Put an applicable fuel container below the drain hole.

3. Remove the oil drain plug and the oil tank cap (B).

4. Drain the engine oil into the container.

5. Install the oil drain plug and tighten it.

6. Fill engine oil. Refer to

To do a check of the engine

oil level on page 11

.

7. Remove oil spillage.

8. Recycle the used engine oil at an approved disposal

location.

To replace the spark plug

Replace the spark plug 1 time each year.

1. Stop the engine.

2. Remove the spark plug cap from the spark plug.

3. Clean the area around the spark plug and remove

the spark plug from the cylinder.

4. Set the electrode gap. Refer to

Technical data on

page 15

.

5. Install a new spark plug. Torque to 15 ft/lbs.

To do a check of the spark arrester

screen

Do a check and clean the spark arrester screen 1 time

each year or more frequently if it is necessary.

WARNING: In some areas and

conditions, you must use a spark arrester

screen to prevent the risk of fire. Obey local

regulations.

1. Remove the clamp (A) and the spark arrester screen

(B) from the muffler (C).

A

B

C

2. Clean the spark arrester screen with commercial

solvent.

3. Examine the spark arrester screen for wear and

damage. Replace the spark arrester screen if it is

necessary.

CAUTION: Do not use a product

with a damaged spark arrester screen.

12 1420 - 004 - 14.02.2022

To do a check of the air filter

1. Remove the knob (A) and the air filter cover (B).

B

A

C

2. Remove the air filter (C).

3. Clean the air filter and the air filter cover with soap

water.

4. Let the air filter and the air filter cover become dry.

5. Install the air filter, the air filter cover and the knob.

Troubleshooting

Troubleshooting schedule

Problem Cause Solution

The engine stops when it has too

much load.

The air filter is not clean. Clean or replace the air filter.

The engine is not warm. Let the engine become warm before

operation.

The engine misfires. The spark plug is loose. Do a check of the wire connections.

Incorrect electrode gap. Replace the spark plug cap.

The spark plug cap is damaged. Replace the spark plug cap.

Expired or low quality gasoline. Fill fuel.

Incorrect compression. Adjust the compression.

The engine stops suddenly. The engine oil level is low. Fill engine oil.

The fuel tank is empty or has low

quality gasoline.

Fill fuel.

Defective fuel tank cap. Replace the fuel tank cap.

Defective magnet. Speak to an approved servicing deal-

er.

The spark plug cap is not correctly

installed.

Install the spark plug cap.

Engine knocking occurs. Expired or low quality gasoline. Fill fuel.

Overload in the engine. Refer to

To prevent overload in the

product on page 10

.

Mechanical problem. Speak to an approved servicing deal-

er.

1420 - 004 - 14.02.2022 13

Problem Cause Solution

Engine backfire occurs. Low quality gasoline. Fill fuel.

The engine is too cold. Use fuel for cold conditions and oil

additives.

The inlet valve is blocked or the en-

gine is too hot.

Speak to an approved servicing deal-

er.

Incorrect ignition timing. Do a check of the ignition timing.

The product has no power. The product is not connected to the

electrical source.

Stop the product and disconnect it.

Connect the product and start it

again.

A circuit breaker has tripped. Stop the product and disconnect it.

Restart the circuit breaker. Connect

the product and start it again.

The receptacle is engaged. Stop the product and disconnect it.

Do a test of the receptacle. If the re-

ceptacle is not damaged, start and

connect the product again.

Servicing is necessary. Speak to an approved servicing deal-

er.

The product does not operate cor-

rectly.

Problem with an electrical device. Disconnect the electrical device.

Speak to an approved servicing deal-

er.

There is too much load in the prod-

uct.

Decrease the quantity of electrical

devices connected to the product.

CAUTION: Speak to an approved

servicing dealer if the problem stays.

To prepare the product for long-term storage

Do the steps that follow if the product will be kept in

storage for more than 30 days. The procedure that

follows prevents problems with the fuel system.

1. Add a fuel stabilizer to the fuel. The fuel stabilizer

must agree with the recommendation from the

manufacturer.

2. Operate the product for 10-15 minutes.

3. Let the engine become cool and drain the fuel tank.

CAUTION: Do not keep fuel in long-

term storage. Discard gasoline that is not

clean.

4. Start the engine and let it operate until all the fuel

has been used and the product stops.

5. Let the engine become cool and replace the engine

oil.

6. Remove the spark plug cap and put ½ oz/15 ml of

engine oil into the cylinder.

7. Put a cloth on the spark plug hole for protection.

8. Pull the starter rope handle 5 times to lubricate the

engine parts.

9. Install and tighten the spark plug.

WARNING: Do not install the spark

plug cap.

10. Clean the product.

11. Put the product in a clean and dry location indoors.

12. Put a cover on the product for protection.

WARNING: Do not put a cover on

the product if it is warm.

14 1420 - 004 - 14.02.2022

Technical data

Husqvarna

G1300P

Husqvarna

G1300P

Husqvarna

G2500P

Husqvarna

G2500P

Husqvarna

G3200P

Engine displace-

ment, cc

98.5 98.5 196 196 212

Peak power, W11000 1200 2200 2800 3000

Rated power, W 800 1000 2000 2500 2800

Voltage, V 230 110/220,120/240 230 110/220,120/240 230

Rated frequency,

Hz

50 60 50 60 50

Phase 1 1 1 1 1

Net weight, kg 28.0 28.0 43.0 43.0 49.0

Gross weight, kg 29.2 29.2 45.0 45.0 51.0

Package size,

mm

500X375X435 500X375X435 500X375X435 500X375X435 625X495X495

Oil tank capacity,

l

0.45 0.45 0.6 0.6 0.6

Electrode gap,

mm/in.

0.76/0.030 0.76/0.030 0.76/0.030 0.76/0.030 0.76/0.030

Type Gasoline Gasoline Gasoline Gasoline Gasoline

Measured Sound

Power Level, dB

(A)

95 95 96

Guaranteed

Sound Power

Level, dB (A)

95 95 96

Husqvarna

G3200P

Husqvarna

G5500P

Husqvarna

G5500P

Husqvarna

G8500P

Husqvarna

G8500P

Engine displace-

ment, cc

212 389 389 458 458

Peak power, W23200 5500 6000 8000 8500

1Maximum wattage is subject to, and limited by, such factors as fuel energy content, ambient temperature,

altitude, engine condition, etc. Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each 6° C (10° F) above 16°C (60° F) ambient temperature.

2Maximum wattage is subject to, and limited by, such factors as fuel energy content, ambient temperature,

altitude, engine condition, etc. Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each 6° C (10° F) above 16°C (60° F) ambient temperature.

1420 - 004 - 14.02.2022 15

Husqvarna

G3200P

Husqvarna

G5500P

Husqvarna

G5500P

Husqvarna

G8500P

Husqvarna

G8500P

Rated power, W 3000 5000 5500 7500 8000

Voltage, V 110/220,120/240 230 110/220,120/240 230 110/220,120/240

Rated frequency,

Hz

60 50 60 50 60

Phase 1 1 1 1 1

Net weight, kg 49.0 88.0 88.0 106.4 106.4

Gross weight, kg 51.0 91.0 91.0 109.5 109.5

Package size,

mm

625X495X495 720X560X585 720X560X585 720X560X585 720X560X585

Oil tank capacity,

l

0.6 1.1 1.1 1.1 1.1

Electrode gap,

mm/in.

0.76/0.030 0.76/0.030 0.76/0.030 0.76/0.030 0.76/0.030

Type Gasoline Gasoline Gasoline Gasoline Gasoline

Measured Sound

Power Level, dB

(A)

96

Guaranteed

Sound Power

Level, dB (A)

96

Watt reference guide

Note: All numbers are approximate. Refer to the data

label on the appliance for wattage requirements.

Device Running W Additional start-up W

Emergency

Refrigerator/freezer 700 1500

Radio 100 0

Job site

Air compressor - ½ HP 1000 1000

Table saw - 10" 1700 1300

Belt sander - 3" 1200 1200

Hand drill - ½" 600 600

Halogen work light 1000 0

Reciprocating saw 900 900

Recreation

AM/FM radio 100 0

16 1420 - 004 - 14.02.2022

Device Running W Additional start-up W

Electric grill 1700 0

Inflation pump 50 100 -

CD/DVD player 100 0

Box fan - 20" 200 200

Coffee maker 600 0

Household

Computer with monitor 800 0

Electric clothes dryer 5500 500

Electric range 2100 0

Electric water heater 2000 0

Light bulb - 100 W 100 0

Microwave - 1000 W 1000 200

Sump pump - ½ HP 1000 1100

Television 400 0

Washing machine 1100 1100

Well pump - ½ HP 1000 1000

Lawn and garden

Hedge trimmer 400 400

Pressure washer 1200 1200

Lawn mower 1200 1200

Edger 1000 1000

Heating and cooling

Central AC - 10000 BTU 1500 1500

Furnace fan - ½ HP 900 1400

Space heater 1800 0

Window AC - 10000 BTU 1200 600

1420 - 004 - 14.02.2022 17

EC Declaration of Conformity

EC Declaration of conformity

For the following machinery:

• Product name: Portable Generator

• Function: Low-power generating set

• Model No.: G 2500P, G 3200P

• Serial No.: 1945013770, 1945013793 and onwards

is herewith confirmed to fulfill all the relevant provisions

of

• Machinery Directive (2006/42/EC)

• Low Voltage Directive (2014/35/EU)

• Restriction of Hazardous Substances (RoHS)

Directive (2011/65/EU)

• Electromagnetic Compatibility Directive

(2014/30/EU)

• Noise Emission Directive by equipment for use

outdoors (2000/14/EC + 2005/88/EC)

and the following harmonized standard has been

complied with:

• EN ISO 8528-13:2016, EN 61000-6-1:2007; EN

55012:2007+A1

Conformity Assessment Procedure: 2000/14/EC,

amended by 2005/88/EC- Annex VI

TÜV Rheinland LGA Products GmbH, Notified Body

for Machinery (notified under 0197), Tillystraße 2

- 90431 Nürnberg, Germany, carried out the noise

certification. For information about noise emissions,

refer to

Technical data on page 15

.

Huskvarna, 2020-06-10

Claes Losdal, Development Manager/Garden Products

(Authorized representative for Husqvarna AB and

responsible for technical documentation).

18 1420 - 004 - 14.02.2022

Съдържание

Въведение................................................................... 19

Безопасност.................................................................22

Монтаж.........................................................................25

Инсталиране................................................................26

Операция..................................................................... 27

Поддръжка...................................................................28

Отстраняване на проблеми........................................31

За да подготвите продукта за продължително

съхранение..................................................................33

Технически данни....................................................... 34

Декларация за съответствие на ЕО.......................... 38

Въведение

Описание на продукта

Този продукт е преносим генератор с двигател с

вътрешно горене.

Предназначение

Продуктът осигурява захранване за електроуреди на

места, където няма налично електрозахранване. Не

използвайте продукта за други задачи.

Общ преглед на продукта

12

3

4

5

6

9

8

7

10

11

15

14

7

13

12

1. Горивен клапан

2. Дросел

3. Въздушен филтър

4. Дръжка на въжето на стартера

5. Колело

6. Акумулатор

7. Прекъсвач

8. Ръкохватка

9. Рамка

10. Индикатор за гориво

11. Капачка на резервоара за гориво

12. Прекъсвачи на електрическата верига за

променлив ток

13. Цифров измервателен уред: показва

напрежението, честотата и работните часове.

14. Клема за заземяване

15. Контакт за променлив ток

1420 - 004 - 14.02.2022 19

Клема за 12 V постоянен ток

Клемата за 12 V постоянен ток е източник на

захранване за уреди, работещи с 12 V прав ток.

Цифров измервателен уред:

показва напрежението, честотата и

работните часове.

Индикаторът показва напрежението, честотата и

общото време на работа на продукта.

V

F

T

Контакти за променлив ток

Продуктът има няколко контакта за променлив ток за

подаване на енергия към инструменти и оборудване.

Контактите за променлив ток са различни за

различните пазари.

ЕС, 1-фазен, 50 Hz

A: 2-полюсен контакт, 230 V.

B: 3-полюсен контакт, 32 A 230 V.

A B

САЩ, 1-фазен, 60 Hz

A: 3-полюсен двоен контакт, 120 V.

B: 4-полюсен контакт със заключване със завъртане,

30 A 120/240 V.

C: 4-полюсен контакт, 50 A 120/240 V.

A B C

САЩ, 3-фазен, 60 Hz

A: 3-полюсен двоен контакт, 110 V.

B: 5-полюсен контакт, 3-фазен, 127/220 V.

A

B

Китай, 1-фазен, 50 Hz

A: 3-полюсен контакт със завъртане със заключване,

230 V.

A

20 1420 - 004 - 14.02.2022

Pagina se încarcă ...

Husqvarna G1300P Manual de utilizare

Husqvarna G1300P Manual de utilizare

în alte limbi

Alte documente