Beko BHCA 64640 B Manual de utilizare

BHCA 64640 B - BHCA 64640 BH

BHCA 94640 BH - BHCA 94640 WH

EN - DE - FR - ES - PL - RO - BG - BS - KA - NL - PT - SK - SQ - CS - SL - KK - RU

01M-8897233200-4421-12

01M-8897243200-4421-12

01M-8897253200-4421-12

01M-8897263200-4421-12

User Manual

Cooker Hood

2 / EN Cooker Hood / User Manual

CONTENTS

ENGLISH 3-17

DEUTSCH 18-34

FRANÇAIS 35-50

ESPAÑOL 51-67

POLSKI 68-85

ROMÂNĂ 86-102

БЪЛГАРСКИ 103-120

BOSANSKI 121-134

ქართული ენა 135-155

NEDERLANDS 156-170

PORTUGUÊS 171-187

SLOVENSKÝ 188-202

SHQIPTARE 203-217

ČESKY 218-232

SLOVENŠČINA 233-246

KAZAKH 247-266

РУССКИЙ 267-288

Please read this user manual first!

Dear Valued Customer,

Thank you for preferring this Beko appliance. We hope that you get the best results

from your appliance which has been manufactured with high quality and state-of-

the-art technology. For this reason, please read this entire user manual and all other

accompanying documents carefully before using the appliance and keep it as a

reference for future use. If you handover the appliance to someone else, give the user

manual as well. Follow the instructions by paying attention to all the information and

warnings in the user manual.

Remember that this user manual may also apply to other models. Differences between

models are explicitly described in the manual.

Meanings of the Symbols

Following symbols are used in various sections of this user manual:

CImportant information and useful hints about

usage.

AWARNING: Warnings against dangerous situa-

tions concerning the security of life and property.

WARNING: Warning for danger of fire.

BWARNING: Warning for electric shock.

This appliance has been produced in environmentally friendly facilities without harming the nature.

4 / EN Cooker Hood / User Manual

1

Important safety and environmental instructions

1.1 General safety

Important Safety Instructions Read

Carefully And Keep For Future

Reference This section contains

safety instructions that will help

protect from risk of fire, electric

shock, exposure to leak micro-

wave energy, personal injury or

property damage. Failure to follow

these instructions shall void any

warranty.

•Beko products comply with the

applicable safety standards;

therefore, in case of any damage

on the appliance or power cable,

it should be repaired or replaced

by the dealer, service center or a

specialist and authorized service

alike to avoid any danger. Faulty

or unqualified repair work may

be dangerous and cause risk to

the user.

•This appliance is intended to be

used in household and similar

applications such as:

– Staff kitchen areas in shops,

offices and other working en-

vironments;

– Farm houses

– By clients in hotels, and other

residential type environments;

– Bed and Breakfast type envi-

ronments.

•Operate the appliance for its

intended purpose only as de-

scribed in this manual.

•The manufacturer cannot be held

liable for damages resulting from

improper installation or misuse of

the product.

•This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental ca-

pabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand the

hazards involved.

•Children shall not be allowed

play with the appliance. Cleaning

and user maintenance shall not

be made by children without su-

pervision.

Cooker Hood / User Manual 5 / EN

1

Important safety and environmental instructions

•The minimum distance between

the supporting surface for the

cooking vessels on the hob and

the lowest part of your product

must be at least 65 cm.

•If the instructions for installation

for the gas hob specify a greater

distance, this has to be taken

into account.

•Make sure that your mains

power supply complies with the

information supplied on the rat-

ing plate of the appliance.

•Never use the appliance if the

power cable or the appliance it-

self is damaged.

•Prevent damage to the power

cable by not squeezing, bending,

or rubbing it on sharp edges.

Keep the power cable away from

hot surfaces and naked flame.

•Use the appliance with a

grounded outlet only.

WARNING: Do not connect the

appliance to the mains until the

installation is fully complete.

•Place the appliance in a way so

that the plug is always accessible.

•Do not touch the lamps if they

have operated for a long time.

They can burn your hands since

they will be hot.

•Follow the regulations set out by

competent authorities on dis-

charge of the exhaust air (this

warning is not applicable for use

without flue).

•Operate your appliance after put-

ting a pot, pan etc. on the hob.

Otherwise, high heat may cause

deformation in some parts of

your product.

•Turn off the hob before taking the

pot, pan etc. from it.

•Do not leave hot oil on the hob.

Pans with hot oil may cause self

combustion.

•Pay attention to your curtains

and covers since oil may catch

fire while cooking food such as

fries.

•Grease filter must be cleaned

at least monthly. Carbon filter

must be replaced at least every

3 months.

6 / EN Cooker Hood / User Manual

1

Important safety and environmental instructions

•Product shall be cleaned ac-

cordance with user manual. If

cleaning was not carried out in

accordance with user manual,

there may be fire risk.

•Do not use non-fire-resistant

filtering materials instead of the

current filter.

•Only use the original parts or

parts recommended by the man-

ufacturer.

•Do not operate the product with-

out the filter and do not remove

the filters while the product is

running.

•In the event of be started any

flame, de-energize your product

and cooking appliances.

•In the event of be started any

flame, cover the flame and never

use water to extinguish.

•Unplug the appliance before

each cleaning and when the ap-

pliance is not in use.

•The negative pressure in the envi-

ronment should not exceed 4 Pa

(4x10 bar) while the hood for elec-

tric hob and appliances running on

another type of energy but electric-

ity operate simultaneously.

•In the environment where the

appliance is being used, the ex-

haust of devices running on fuel

oil or gas, such as room heater

must be absolutely isolated or

device must be hermetical type.

•When connecting the flue, use

pipes with a diameter of 120 or

150 mm. Pipe connection must

be as short as possible and have

as few elbows as possible.

•Danger of choking! Keep all the

packaging materials away from

children.

CAUTION: Accessible parts may

become hot when used with cook-

ing appliances.

•The product outlet must not be

connected to air channels that

include other smoke.

•The ventilation in the room may

be insufficient when the hood for

electric hob is used simultane-

ously with the devices operating

on gas or other fuels (this may

not apply to appliances that only

discharge the air back into the

room).

Cooker Hood / User Manual 7 / EN

1

Important safety and environmental instructions

•Objects placed on the product

may fall. Do not place any ob-

jects on the product.

•Do not flambe under the your

product.

WARNING: Before installing the

Hood, remove the protective films.

•Never leave high naked flames

under the hood when it is in op-

eration

•Deep fat fryers must be contin-

uously monitored during use:

overheated oil can burst into

flames.

1.2 Compliance with the WEEE

Directive and Disposing of the Waste

Product:

This product complies with EU WEEE Directive

(2012/19/EU). This product bears a classification

symbol for waste electrical and electronic equip-

ment (WEEE).

This symbol indicates that this product

shall not be disposed with other

household wastes at the end of its ser-

vice life. Used device must be returned

to offical collection point for recycling

of electrical and electronic devices. To find these

collection systems please contact to your local au-

thorities or retailer where the product was pu-

chased. Each household performs important role

in recovering and recycling of old appliance.

Appropriate disposal of used appliance helps pre-

vent potential negative consequences for the envi-

ronment and human health.

1.3 Compliance with RoHS Directive

The product you have purchased complies with EU

RoHS Directive (2011/65/EU). It does not contain

harmful and prohibited materials specified in the

Directive.

1.4 Package Information

Packaging materials of the product are

manufactured from recyclable materials

in accordance with our National

Environment Regulations. Do not dis-

pose of the packaging materials together with the

domestic or other wastes. Take them to the pack-

aging material collection points designated by the

local authorities.

8 / EN Cooker Hood / User Manual

596

411

395

350

414

80 25

Min:750 Max:1130

213

166.5

380

20

400

6

1. Inner chimney

2. Outer chimney

3. Grease filter (Behind glass cover)

4. Glass cover

5. Control panel

6. Lighting

2.2 Technical Data

Model BHCA 64640 B

BHCA 64640 BH BHCA 94640 BH

BHCA 94640 WH

Supply voltage & Frequency 220-240V ~ 50 Hz

Lamp Power 2 x 3 W

Motor Power 210 W

Flow rate – 3. Level 631 m³/h 623 m³/h

Insulation Class of Motor Class F

Insulation Class Class I

(Figure 2)

(Figure 1)

896

411

690

350

414

80 25

Min:750 Max:1130

261

250

380

20

400

BHCA 64640 B

BHCA 64640 BH

BHCA 94640 BH

BHCA 94640 WH

2.1 Overview

2

General appearance

Cooker Hood / User Manual 9 / EN

3.1 Controlling the Appliance

KEY FUNCTION

A : Light On

/ Off

You may illuminate the cooking

area by pressing this button. Re-

press the button to turn off the

lamp.

B : 1. Stage

Button

Operates the appliance on 1st

speed. When you press this button

again to turn off the appliance, the

screen speed stage turns off.

C : 2. Stage

Button

Operates the appliance on 2nd

speed. When you press this button

again to turn off the appliance, the

screen speed stage turns off.

D : 3rd Stage

Button

Operates the appliance on 3rd

speed. When you press this button

again to turn off the appliance, the

screen speed stage turns off.

3.2 Energy efficient usage

•When using your appliance, adjust the speed

settings according to vapour and odour intensity,

in order to save energy.

•Use low speeds (1-2) under normal conditions,

and high speed (3) for intense odour and vapour.

•The lamps on the hood are placed for illuminat-

ing the cooking area.

•Using them for environmental lighting shall

cause unnecessary energy expenditure and in-

sufficient lighting.

3.3 Operating the hood

•Your appliance contains a motor that has various

speeds.

•For better performance, we recommend using

low speeds under normal conditions and high

speeds in cases of strong odours and intense

vapour.

3

Operation of the appliance

•You can start your appliance by pressing on the

desired speed setting button. (B, C, D).

•You may illuminate the cooking area by pressing

the lamp (A).

3.4 Automatic stop

Your appliance has Automatic Stop feature, ena-

bling it to ventilate for a bit more and remove the

unwanted odours and vapour inside the environ-

ment and turn off automatically after the cooking

is done. To enable Automatic Stop feature, press

the any speed stage button (B, C, D) on the control

panel for longer than 2 seconds; the 15-minute

timer function shall be activated. When the au-

tomatic stop feature is active, pressing the same

speed button shall disable the automatic stop

function and the appliance’s motor shall stop. This

feature is disables when you switch between dif-

ferent speed stages. If you want the appliance to

stop automatically, you need to enable the auto-

matic stop feature again.

3.5 Replacement of Lamp

MAX 3 W

(Figure 3)

Make the electrical connections of the appliance.

Your appliance uses 3W spot LED lamp. For re-

placing the lamps, push downwards on the holder

from its behind, turn it counter-clockwise, and take

it out downwards. Apply the above operation in re-

verse to install new lamps (Figure 3).

10 / EN Cooker Hood / User Manual

Bulb

Bulb Power 3 W

Holder / Socket GZ 10

Bulb Voltage 220 - 240 V

Size 53 x 50 mm

ILCOS Code DR/F3-220-240-GZ10-50-53

Luminous flux 250 lm

Correlated colour

temperature

3000 K

This product contains a light source of energy ef-

ficiency class “F”.

3.6 Operation with chimney

connection

•Vapour is extracted through the

flue duct, which is fastened to

the connection head on the

hood.

•The diameter of the flue duct must be the same

as the connection ring. In horizontal settings, the

pipe has to have a slight upward slope (around

10º) so that the air can exit the room easily.

3.7 Operation without chimney

connection

•Air is filtered through the carbon

filter and recirculated in the

room. Carbon filter is used

when it is impossible to use a

flue in the house.

•In flueless use, remove the flaps inside the flue

adapter.

•Remove the Grease filter. To install the carbon

filter, fit the filter to the tabs by centring it on

the plastic piece on both sides of the fan body.

tighten it by turning right or left.

•Replace Grease filter.

3

Operation of the appliance

Cooker Hood / User Manual 11 / EN

CBefore cleaning and maintenance,

unplug the product or turn off the

switch.

4.1 Cleaning of the grease filter

This filter retains the oil particles in the air. Grease

filter may change colour as they are washed; this

is normal and does not require replacing your

grease filter.

(Figure 4)

•Push the grease filter lock forward.

•Then pull it slightly down and pull it out (Figure

4). Otherwise, you can bend the filter. Wash and

rinse Grease filter with liquid detergent and re-

place grease filter to their sockets by by carrying

out the steps specified above in reverse order.

This filter retains the oil particles in the air.

CYou may wash your grease filter in

the dishwasher.

ACAUTION: In case of normal use,

clean your filter once in a month.

4.2 Replacement of Carbon Filters

Odour removing filters contain charcoal (Active car-

bon). Grease filter must be installed in the product,

regardless of whether or not carbon filters are used.

(Figure 5)

•Remove the grease filter (Figure 4)

•To remove the carbon filter, remove the car-

bon filter from its housing by rotating it coun-

ter-clockwise from the tab (Figure 5).

•Install the new carbon filter.

•Install the grease filter.

A

CAUTION

•Carbon filter shall never be

washed.

•Replace carbon filters once every

3 months.

•You can obtain the carbon filter

from the authorized services.

4

Cleaing and maintenance

12 / EN Cooker Hood / User Manual

AWARNING: Before starting the in-

stallation, read the safety informa-

tion on user manual.

BWARNING: Failure to install with

screws and stabilizers in accordance

with these instructions may result in

electric shock.

For the installation of the hood, please contact the

nearest Authorized Service.

It is the customer’s responsibility to prepare the

location and electrical installation of the hood.

5.1 Position of the appliance

(Figure 6)

•Distance between the cooker and the cooker

hood must be considered prior to assembly. This

distance should be 65 cm (Figure 6).

•Distance must be measured from the surface of

grate for gas cookers,

•from surface of glass for electric cookers.

5.2 Installation Accessories

12 13 14

BHCA 64640 B - BHCA 64640 BH

BHCA 94640 BH - BHCA 94640 WH

EN - DE - FR - ES - PL - RO - SQ - RU

01M-8897233200-4321-11

01M-8897243200-4321-11

01M-8897253200-4321-11

01M-8897263200-4321-11

User Manual

Cooker Hood

1. Product

2. Inner Chimney

3. Outer Chimney

4. Chimney Connection Plate

5. User Manual

6. Assembly Pattern

7. 2x Ø6mm Plastic Dowel

8. 4x Ø8mm Plastic Dowel

9. 4x 4.8x50 Wall Mount Screw

10. 2x 3.9x22 Chimney Connection Plate Screw

11. 4x 3.5x9.5 Chimney Connection Screw

12. Chimney Clamp

13. 150/120mm Plastic Chimney Adapter

14. Air Baffle

15. Plastic Adapter (Air Diverter)

The information required to make the location suit-

able for the installation of the hood is given below.

5.3 Wall Mounting

•Wall must be flat, straight and have the suffi-

cient bearing capacity.

5

Installation of appliance

Cooker Hood / User Manual 13 / EN

To assemble the hood body, you can use the

Ø8mm drill bit to drill points A, B, C, D on the as-

sembly template, and insert 4.8x50mm plastic

dowels at these points. (Figure 7/b).

2 piece 4.8x50 suspension screw with a clearance

of 5 mm between the screw head and the wall

(Figure 7/b).

(Figure 8)

1. Hanger Plate

2. Hanging Plate Connection Screw

In order to install your hood to the wall, loosen the

screws on the hanger plates mounted on the mo-

tor cabin and pull them up, and then fasten again

(Figure 8/A).

Turn on the suction glass of the hood and remove

the grease filter (Figure 4).

Ø4,8x50mm

(Figure 9)

Hold the cooker hood by its body and place it on

the mounting screws on the wall and tighten the

screws (Figure 9).

Secure the cooker hood with two 4.8x50 screws to

the wall through the mounting hole on the interior

of the appliance (Figure 9).

5

Installation of appliance

•Depth of drilling holes must comply with the

length of bolts.

•The bolts and dowels provided are suitable for

brick walls. For other construction material (e.g.

drywall, plate, porous concrete), suitable fixing

dowels and nuts shall be used.

(Figure 7)

ACAUTION: Before drilling, ensure

that there are no power, gas or wa-

ter pipes in the close proximity of the

drilling locations.

Draw a mid location line from the ceiling perpen-

dicular to the lower edge of the hood.

Paste the installing template provided within the

accessories on the surface where the hood is to

be mounted. In doing this operation, observe the

mounting height of the hood (Figure 6).

There is a tab in the middle of the Chimney con-

nection plate. Place the middle point of this tab on

the line that is drawn perpendicular to the wall.

In doing this operation, adjust the hood accord-

ing to the maximum height (Figure 1). Mark the

holes where the Chimney connection plate will be

mounted with the help of a pen (Figure 7/a).

Drill the marked points with Ø6mm drill and insert

2 plastic dowels in the drilled holes (Figure 7/a).

Fix the Chimney connection plate to the wall with

3,9x22 screws (Figure 7/a).

14 / EN Cooker Hood / User Manual

5.4 Connecting to Chimney

(Figure 10)

1. Flap Pin Socket

2. Flap Pin

Insert the plastic pin (Figure 10/area no. 2) on the

pin socket on the motor exhaust (Figure 10/area

no.1). Then bend the flap lightly to insert the other

pin on the flap and insert the other pin to its socket

(Figure 10).

If you are going to use the Ø 120/150 mm plastic

Chimney adapter, connect one end of the pipe to

this adapter, if you are not going to use it, to the

direct output on the product. Connect the other

end of the pipe to your chimney. Check that these

two connections are tight enough so they will not

come out when the appliance runs on full power.

Ensure that the flaps inside the Chimney work

when tightened with clamp. Connect the Chimney

connection duct outside the adapter (Figure 11/a).

If the connection duct is fitted inside the adapter,

suction of air shall not occur as the Chimney flap

that prevents the return of air will remain closed

(Figure 11 / b). The length of the pipe connection

as well as the number of elbows must be as min-

imum as possible.

A : Chimney exit pipe

B : Chimney Clamps

C: Plastic Chimney

The valves are closed then the appliance is not

operating and prevent possible outside odour and

dust from entering inside.

Ok Not Ok

(a) (b)

(Figure 11)

5.5 Installation of the Hood to the

Chimney

Make the electrical connection of your hood be-

fore starting the installation of the chimney. Slip

the Chimney plates around the body. Screw the

Chimney to the Chimney fastening plates availa-

ble on the motor cabin. (Figure 12).

Install the Chimney to the Chimney fastening plate

that is secured to the wall from its upper outer

edges (Figure 12).

(Figure 12)

5

Installation of appliance

Cooker Hood / User Manual 15 / EN

5.6 Installation of Air Baffle (BHCA

64640 BH - BHCA 94640 BH - BHCA

94640 WH)

While using with the carbon filter, air baffle is pro-

vided with your appliance with the aim of re-re-

leasing the air which is cleaned with carbon fil-

ter from the perforated located on the chimney.

Assemble the air baffle as below.

(Figure 13)

There is a tab in the middle of the chimney con-

nection plate. Place the middle point of this tab on

the line that is drawn perpendicular to the wall.

Align horizontally and mark the holes where the

connection plate will be mounted via a pen (Figure

13/A, B).

Drill the marked points with Ø6mm drill and in-

sert two Ø6mm plastic dowels in the drilled holes

(Figure 13/A, B).

Fix the Chimney connection plate to the wall with

3.9x22 screws (Figure 13/A, B).

For the assembly air baffle, drill points C, D, E, F

with a Ø6mm drill bit and tap the Ø6mm plastic

dowels (Figure 13).

Assemble cooker hood's body (Figure 9).

5

Installation of appliance

1

2

(Figure 14)

1. Air Baffle

2. Plastic Chimney

Attach the plastic Chimney adapter, which is in-

cluded in the package, in the direction of the air

baffle. Lock the Chimney adapter by turning it in

the direction of the arrow (Figure 14).

(Figure 15)

Assemble the air baffle group with 3.9 x 22

screws from point C, D, E, F that you have already

prepared (Figure 15).

16 / EN Cooker Hood / User Manual

(Figure 16)

1. Aluminium Air Outlet Pipe

Make the air outlet pipe assembly (Figure 16).

C

Since twists and bends in the alu-

minium pipe will lead to reduction

in the air suction power, avoid using

twists and bends as much as pos-

sible.

Install the Chimney plates of the hood (Figure 9)

5

Installation of appliance

Cooker Hood / User Manual 17 / EN

6

Troubleshooting

Troubleshooting Root cause Help

Appliance is not working. Check your fuses. Fuse may be blown, inspect and restore it.

Appliance is not working. Check the electrical connection. Mains voltage shall be between 220 and 240 V.

Appliance is not working. Check the electrical connection. Check if other appliance in your kitchen

operate.

Illumination light does

not operate. Check the electrical connection. Mains voltage shall be between 220 and 240 V.

Illumination light does

not operate. Inspect the lamp switch. Lamp switch shall be at “on” position.

Illumination light does

not operate. Inspect the lamps. The lamps of the appliance shall illuminate.

Air inlet of the appliance

is inadequate. Inspect the aluminium filter. Under normal operating conditions, Grease filter

shall be cleaned at least once in a month.

Air inlet of the appliance

is inadequate. Check the air discharge chimney. The air discharge chimney shall be at “on” po-

sition.

Air inlet of the appliance

is inadequate. Inspect the carbon filter. The filters of the appliances with carbon filters

shall be replaced once in every 3 months under

normal conditions.

Bitte lesen Sie zunächst diese Anleitung!

Sehr geehrte Kundin, sehr geehrter Kunde,

Vielen Dank, dass Sie sich für dieses Gerät der Marke Beko entschieden haben. Wir sind

überzeugt, dass Sie mit diesem Gerät, das mit den höchsten Qualitätsanforderungen

und modernster Technologie hergestellt wurde, beste Ergebnisse erzielen werden.

Bitte lesen Sie die gesamte Bedienungsanleitung und alle anderen Begleitdokumente

aufmerksam, bevor Sie das Gerät verwenden; bewahren Sie sie zum künftigen

Nachschlagen sicher auf. Wenn Sie das Gerät an jemanden weitergeben, händigen

Sie ihm bitte auch diese Anleitung aus. Befolgen Sie die Anweisungen, indem Sie alle

Informationen und Warnhinweise in der Bedienungsanleitung beachten.

Bitte denken Sie daran, dass diese Bedienungsanleitung eventuell für mehrere Modelle

geschrieben wurde. Unterschiede zwischen den Modellen werden in der Anleitung klar

und deutlich beschrieben.

Bedeutung der Symbole

Folgende Symbole werden in den verschiedenen Abschnitten dieser Anleitung

verwendet:

CWichtige Informationen und nützliche Hinweise zur

Verwendung.

AWARNUNG: Warnhinweise zu gefährlichen

Situationen im Hinblick auf die Sicherheit von Leib,

Leben und Eigentum.

Warnung vor Brandgefahr.

BWarnung vor Stromschlägen.

Dieses Gerät wurde in umweltfreundlichen, modernen Einrichtungen ohne schädliche Auswirkungen auf

die Natur hergestellt.

Dunstabzugshaube / Bedienungsanleitung 19 / DE

1.1 Allgemeine Sicherheit

Wichtige Sicherheitsanweisungen

sorgfältig lesen und zum künftigen

Nachschlagen aufbewahren

Dieser Abschnitt enthält

Sicherheitsanweisungen, die

beim Schutz vor Personen-

und Sachschäden, Bränden,

Stromschlägen und dem

Austreten von Mikrowellenenergie

helfen. Bei Nichtbeachtung dies-

er Anweisungen erlischt die

Gewährleistung.

•Beko-Produkte stimmen mit

geltenden Sicherheitsstandards

überein; daher sollten Gerät oder

Netzkabel zur Vermeidung von

Gefahren im Falle von Schäden

durch den Händler, ein Kunden-

center oder einen spezialisierten,

autorisierten Serviceanbieter

repariert oder ersetzt werden.

Fehlerhafte oder unqualifizierte

Reparaturen können Gefahren

und Risiken für den Benutzer

verursachen.

•Dieses Gerät ist für den Einsatz

in Haushalten und ähnlichen

Bereichen vorgesehen, wie:

– In Betriebsküchen, Läden,

Büros und anderen Arbeit-

sumgebungen;

– Bauernhöfen;

– Von Gästen in Hotels und an-

deren Wohnumgebungen;

– Pensionen und Jugendher-

bergen.

•Das Gerät darf nur für seinen in

dieser Anleitung beschriebenen

vorgesehenen Zweck verwendet

werden.

•Der Hersteller haftet nicht für

Schäden, die auf unsachgemäße

Installation oder fehlerhaften Ge-

brauch zurückzuführen sind.

•Das Gerät darf nur dann von

Kindern ab 8 Jahren und Perso-

nen mit körperlichen oder geis-

tigen Einschränkungen genutzt

werden, wenn diese beaufsichtigt

werden oder gründlich über den

richtigen und sicheren Umgang

mit dem Gerät aufgeklärt wurden

und sich sämtlicher möglicher

Gefahren bewusst sind.

1

Wichtige Sicherheits- und Umweltanweisungen

20 / DE Dunstabzugshaube / Bedienungsanleitung

•Kinder dürfen nicht mit dem

Gerät spielen. Reinigungs- und

Wartungsarbeiten dürfen nicht

unbeaufsichtigt von Kindern aus-

geführt werden.

•Der Abstand zwischen der Stütz-

fläche für Kochgeschirr auf dem

Kochfeld und dem niedrigsten

Teil der Abzugshaube muss

mindestens 65 cm betragen.

•Falls die Anweisungen zur In-

stallation eines Gasherdes einen

größeren Abstand angeben, ist

dieser einzuhalten.

•Stellen Sie sicher, dass Ihre

Stromversorgung mit den Anga-

ben am Typenschild des Gerätes

übereinstimmt.

•Benutzen Sie das Gerät niemals,

wenn das Netzkabel oder das

Gerät selbst beschädigt ist.

•Vermeiden Sie Schäden am

Netzkabel, indem Sie es nicht

quetschen, knicken oder über

scharfe Kanten ziehen. Halten

Sie das Netzkabel von heißen

Oberflächen und offener Flamme

fern.

•Verwenden Sie das Gerät nur mit

einer geerdeten Steckdose.

WARNUNG: Schließen Sie das

Gerät erst nach vollständig ab-

geschlossener Installation an das

Stromnetz an.

•Stellen Sie das Gerät so auf,

dass der Netzstecker immer

zugänglich ist.

•Berühren Sie die Lampen nicht,

falls sie lange Zeit in Betrieb

waren. Sie könnten sich die Fin-

ger verbrennen, da die Lampen

heiß werden.

•Befolgen Sie die von zuständigen

Behörden festgelegten Richt-

linien zum Abführen von Abluft

(diese Warnung ist bei Einsatz

ohne Abzug nicht zutreffend).

•Nehmen Sie Ihr Gerät erst in

Betrieb, nachdem Sie ein Koch-

geschirr auf das Kochfeld gestellt

haben. Andernfalls könnte hohe

Hitze zur Verformung von Teilen

Ihres Geräts führen.

•Schalten Sie die Kochfelder

ab, bevor Sie das Kochgeschirr

herunternehmen.

•Lassen Sie kein heißes Öl auf das

Kochfeld gelangen. Kochgeschirr

mit heißem Öl kann sich selbst

entzünden.

1

Wichtige Sicherheits- und Umweltanweisungen

Pagina se încarcă...

Beko BHCA 64640 B Manual de utilizare

Beko BHCA 64640 B Manual de utilizare

în alte limbi

Lucrări înrudite

Alte documente