Yamaha YSP-900 Manualul proprietarului

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

Printed in Malaysia WH83000

YSP-900

Digital Sound Projector

Système Acoustique Numérique

G

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

YSP-900_G-cv.fm Page 1 Friday, August 11, 2006 2:48 PM

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place with at least 5 cm of space above (or below) this unit –

away from direct sunlight, heat sources, vibration, dust, moisture,

and/or cold.

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high

humidity (i.e. a room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp

the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. YAMAHA will

not be held responsible for any damage resulting from use of this

unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press STANDBY/ON to set this unit in

standby mode, and disconnect the AC power plug from the wall

outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the outlet,

then leave the unit alone.

19 When using the unit for a long time, the unit may become warm.

Turn the power off, then leave the unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug

can be reached easily.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as

long as it is connected to the AC wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

FOR U.K. CUSTOMERS

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below. Note that the plug severed from

the mains lead must be destroyed, as a plug with bared

flexible cord is hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED. Make sure that neither core is connected to the

earth terminal of the three pin plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

SETUP

English

OVERVIEW ........................................................... 2

FEATURES............................................................. 3

USING THIS MANUAL........................................ 4

SUPPLIED ACCESSORIES ................................. 5

CONTROLS AND FUNCTIONS ......................... 6

Front panel ................................................................. 6

Front panel display .................................................... 7

Rear panel .................................................................. 8

Remote control........................................................... 9

INSTALLATION ................................................. 11

Before installing this unit......................................... 11

Installing this unit .................................................... 11

CONNECTIONS .................................................. 14

Connecting a TV...................................................... 15

Connecting a DVD player/recorder ......................... 16

Connecting a VCR................................................... 17

Connecting a digital satellite tuner or

a cable TV tuner .................................................. 18

Connecting other external components ................... 19

Connecting a subwoofer .......................................... 20

Connecting the power supply cable......................... 21

GETTING STARTED.......................................... 22

Installing batteries in the remote control ................. 22

Operation range of the remote control..................... 22

Using the remote control ......................................... 23

Turning on the power............................................... 23

USING SET MENU.............................................. 24

Displaying the OSD................................................. 24

The flow chart of SET MENU................................. 25

CHANGING OSD LANGUAGE ........................ 26

AUTO SETUP (IntelliBeam) ............................... 27

The flow chart of AUTO SETUP ............................ 27

Installing the optimizer microphone........................ 28

Using AUTO SETUP (IntelliBeam)........................ 29

USING THE SYSTEM MEMORY .................... 34

Convenient usage of the system memory ................ 34

Saving settings......................................................... 34

Loading settings....................................................... 35

PLAYBACK.......................................................... 37

Selecting the input source........................................ 37

Playing back sources................................................ 38

Adjusting the volume............................................... 39

Muting the sound ..................................................... 39

ENJOYING SURROUND SOUND .................... 40

5 beam...................................................................... 40

Stereo plus 3 beam................................................... 41

3 beam...................................................................... 41

Enjoying 2-channel sources

in surround sound ................................................ 43

Enjoying TV in surround sound .............................. 44

Adjusting surround mode parameters...................... 45

ENJOYING STEREO SOUND ...........................46

Stereo playback........................................................ 46

PLAYING BACK SOUND CLEARLY

(My beam) ..........................................................47

Using auto-adjust function....................................... 47

Using manual-adjust function.................................. 48

USING SOUND FIELD PROGRAMS................49

What is a sound field? ............................................. 49

Turning on CINEMA DSP programs ...................... 50

Turning off CINEMA DSP programs ..................... 51

Adjusting CINEMA DSP effect levels.................... 51

USING THE VOLUME MODE

(Night listening mode/TV volume

equal mode)........................................................52

USING BASS SOUND ENHANCER

(TruBass)............................................................54

USING THE SLEEP TIMER ..............................55

Setting the sleep timer ............................................. 55

Canceling the sleep timer ........................................ 56

MANUAL SETUP.................................................57

Using MANUAL SETUP........................................ 58

BEAM MENU......................................................... 59

SOUND MENU....................................................... 63

INPUT MENU......................................................... 65

DISPLAY MENU.................................................... 67

ADJUSTING THE AUDIO BALANCE .............68

Using the test tone ................................................... 68

Using the audio output being played back............... 69

SELECTING THE INPUT MODE .....................71

ADJUSTING SYSTEM PARAMETERS ...........72

Using the system parameters ................................... 72

Setting the MEMORY PROTECT .......................... 72

Setting the MAX VOLUME.................................... 73

Setting the TURN ON VOLUME ........................... 74

Setting the DEMO MODE ...................................... 74

Setting the FACTORY PRESET............................. 75

REMOTE CONTROL FEATURES ...................77

Setting remote control codes ................................... 77

Controlling other components ................................. 78

Using the TV macro ................................................ 80

TROUBLESHOOTING .......................................82

GLOSSARY...........................................................85

Audio formats .......................................................... 85

Audio information ................................................... 85

INDEX....................................................................86

SPECIFICATIONS...............................................87

LIST OF REMOTE CONTROL CODES....................i

CONTENTS

INTRODUCTION

PREPARATION

SETUP

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

01EN_YSP-900_G_EN.book Page 1 Tuesday, August 29, 2006 4:46 PM

OVERVIEW

2 En

It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of

wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of

surround sound experience as your local movie theater.

YAMAHA YSP-900 Digital Sound Projector challenges this preconception that complicated speaker setup and

troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.

This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is

not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been

waiting for from its built-in 2 woofers and 21 full-range small speakers.

You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly

directional sound that comes in on the listening position from all directions.

The YSP-900 projects sound beams containing surround sound information for the front right (R), front left (L), surround

right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room before

reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector creates

true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.

Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.

OVERVIEW

SL

SR

R

L

C

Listening position

Imaginary

surround left

speaker

Imaginary

surround right

speaker

Imaginary

front left

speaker

Imaginary

front right

speaker

Imaginary

center

speaker

FEATURES

3 En

INTRODUCTION

English

Digital Sound Projector

This unit employs the digital sound projector technology

that allows one slim unit to control and steer multiple

channels of sound to generate multi channel surround

sound, thus eliminating the need for satellite loudspeakers

and cabling normally associated with conventional

surround sound systems. This unit is also equipped with

the following beam modes so that you can enjoy the

surround sound.

◆ 5 beam

◆ Stereo plus 3 beam

◆ 3 beam

This unit also employs the stereo playback and my beam.

My beam

This unit employs the my beam so that you can achieve a

clear sound in noisy environment. You can adjust the

beam angle manually or automatically using the supplied

remote control.

Cinema DSP Digital

This unit employs the Cinema DSP Digital technology

developed by YAMAHA Electronics Corp. so that you can

experience movies at home with all the dramatic sound

impact that the director intended to convey.

Versatile Remote Control

The supplied remote control come with preset remote

control codes to be used to control the DVD player, VCR,

cable TV tuner and digital satellite tuner connected to this

unit. In addition, the remote control is equipped with the

macro capability so that you can perform a series of

operations with the press of a single button.

AUTO SETUP (IntelliBeam)

This unit employs the automatic sound beam and acoustic

optimization technology with the aid of the supplied

optimizer microphone so that you can avoid troublesome

listening-based speaker setup and achieve highly accurate

sound beam adjustments that best match your listening

environment.

Compatibility with the Newest Technologies

This unit employs decoders compatible with Dolby

Digital, DTS (Digital Theater Systems), Dolby Pro Logic,

Dolby Pro Logic II and DTS Neo:6.

◆ Dolby Digital

This is the standard audio signal format used on DVDs and

other purely digital media. This surround technology deliver

high-quality digital audio for up to 5.1 discrete channels to

produce a directional and more realistic effect.

◆ DTS (Digital Theater Systems)

This is an audio signal format used on DVDs and other purely

digital media. This surround technology deliver high-quality

digital audio for up to 5.1 discrete channels to produce a

directional and more realistic effect.

◆ Dolby Pro Logic

This sophisticated, matrix decoding technology up-converts

any 2 channel source audio to a 5.1 channel full bandwidth

playback, resulting in a surround sound experience.

◆ Dolby Pro Logic II

This is fundamentally a redesigned version of Dolby Pro

Logic that employs 2 stereo surround channels, a subwoofer

and a greatly enhanced steering logic. As a result, this

improved technology provides an exceptionally stable sound

field that simulates 5.1 to a much greater degree than the

original Dolby Pro Logic. In addition, Dolby Pro Logic II

features Movie, Music and Game modes specifically designed

for movies, music and games respectively.

◆ DTS Neo:6

This technology decodes the conventional 2 channel sources

for 6 channel playback, enabling playback with the full-range

channels with higher separation. Music mode and Cinema

mode are available to play back music and movie sources

respectively.

The “ ” logo and “IntelliBeam” are trademarks of

YAMAHA Corporation.

The “ ” logo and “Cinema DSP” are registered

trademarks of YAMAHA Corporation.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS” and “Neo:6” are trademarks of Digital Theater Systems,

Inc.

Manufactured under license from 1 Ltd. Worldwide patents

applied for.

The “ ” logo and “Digital Sound Projector

™

” are trademarks

of 1 Ltd.

TruBass, SRS and the “ ” symbol are registered trademarks

of SRS Labs, Inc. TruBass technology is incorporated under

license from SRS Labs, Inc.

FEATURES

USING THIS MANUAL

4 En

• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the

supplied owner’s manual for the component.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases, the operation is

described using remote control operation.

• y indicates a tip for your operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

1 Install this unit in your listening room.

See “INSTALLATION” on page 11.

2 Connect this unit to your TV and other external components.

See “CONNECTIONS” on page 14.

3 Prepare the remote control and turn on the power of this unit.

See “GETTING STARTED” on page 22.

4 Run AUTO SETUP.

See “AUTO SETUP (IntelliBeam)” on page 27.

5 Play back a source.

See “PLAYBACK” on page 37.

6 Change the beam modes and/or CINEMA DSP settings.

See “ENJOYING SURROUND SOUND” on page 40.

7 Run MANUAL SETUP to fine-tune settings and/or set remote control codes.

See “MANUAL SETUP” on page 57 and “REMOTE CONTROL FEATURES” on page 77.

USING THIS MANUAL

Notes

If you want to make additional settings

and adjustments

SUPPLIED ACCESSORIES

5 En

INTRODUCTION

English

Check that you have received all of the following parts.

SUPPLIED ACCESSORIES

POWER

STANDBY/ON

STEREO

MY BEAM

INPUT2

TV

21

SLEEP

CH LEVEL MENU

RETURN

TEST

TV VOL

VOLUME

MUTE TV INPUT TV MUTE

ENTER

SURROUND

OFF

CODE SET

SPORTS

AV

3

4

56

789

0

+10

5BEAM

ST+3BEAM

3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

INPUTMODE

MACROINPUT1

AUX

YSP

TV/AV

CH

TV

STB VCR DVD

Remote control (×1) Batteries (×2)

(AA, R6, UM-3)

OSD video pin cable (×1)

Optimizer microphone (×1)

Fasteners (×4)

Audio pin cable (×1)

Digital audio pin cable (×1)

Optical cable (×1)

Cable clamp (×1)

Cardboard microphone

stand (×1)

(Orange)

(White/Red)

(Yellow)

CONTROLS AND FUNCTIONS

6 En

1 OPTIMIZER MIC jack

Use to connect the supplied optimizer microphone to be

used to run AUTO SETUP (see page 28).

2 Front panel display

Shows information about the operational status of this

unit.

3 Remote control sensor

Receives infrared signals from the remote control.

4 INPUT

Press repeatedly to switch between input sources (TV,

VCR, DVD or AUX). See page 37 for details.

Outputs a test tone to experience the sound beam (see

page 68).

5 VOLUME –/+

Controls the volume level of all audio channels (see

page 39).

6 STANDBY/ON

Turns on the power of this unit or sets it to the standby

mode (see page 23).

• When you turn on the power of this unit, you will hear a click

and there will be a 4 to 5-second delay before it can reproduce

sound.

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared-signals from the remote

control.

CONTROLS AND FUNCTIONS

Front panel

1 2 3

4 5 6

STANDBY/ONVOLUME

+

INPUT

Notes

01EN_YSP-900_G_EN.book Page 6 Tuesday, August 29, 2006 4:46 PM

CONTROLS AND FUNCTIONS

7 En

INTRODUCTION

English

1 NIGHT indicator

Lights up when one of the night listening modes is

selected (see page 52).

2 SLEEP indicator

Lights up when the sleep timer is turned on (see page 55).

3 Decoder indicators

Light up when the corresponding decoder of this unit is in

operation (see page 42).

4 Volume level indicator

Shows the current volume level (see page 39).

5 Multi-information display

Shows information when you adjust the parameters of this

unit.

y

You can adjust the brightness of the front panel display using the

DISPLAY MENU parameters in MANUAL SETUP (see

page 67).

Front panel display

NIGHT SLEEP PCM PL

m

ft

mS

dB

VOLDIGITAL

5

412 3

CONTROLS AND FUNCTIONS

8 En

1 VCR analog audio input jacks

Use to make an analog connection to your VCR

(see page 17).

2 TV/STB analog audio input jacks

Use to make an analog connection to your TV, digital

satellite tuner and cable TV tuner (see pages 15 and 18).

3 SUBWOOFER OUT jack

Use to connect a subwoofer (see page 20).

4 VIDEO OUT jack

Use to connect to the video input terminal of your TV to

display the OSD of this unit (see page 15).

5 TV/STB OPTICAL DIGITAL INPUT jack

Use to connect a TV, digital satellite tuner and cable TV

tuner via an optical digital connection (see pages 15 and

18).

6 AUX OPTICAL DIGITAL INPUT jack

Use to connect an external component via an optical

digital connection (see page 19).

7 DVD COAXIAL DIGITAL INPUT jack

Use to connect a DVD player via a coaxial digital

connection (see page 16).

8 AC power supply cable

Use to connect to the AC wall outlet (see page 21).

Rear panel

8

1234 5 6 7

VCR

SUBWOOFER

TV/STB

AUDIO INPUT

OUT

OPTICAL

DIGITAL INPUT

TV/STB VIDEO

AUX

DVD

COAXIAL

(Europe model)

CONTROLS AND FUNCTIONS

9 En

INTRODUCTION

English

The functions of some buttons change depending on the

position of the operation mode selector (S). This section

basically describes the functions of the remote control

used to control this unit.

y

You can also control other components using the remote control

once you set the appropriate remote control codes. See

“Controlling other components” on page 78 for details.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 STANDBY/ON

Sets this system to the standby mode (see page 23).

3 Transmission indicator

Lights up when infrared control signals are being output.

4 Input selector buttons

Use to select an input source (STB, VCR, DVD, AUX or

TV).

Use to change the control area of the remote control.

(S: TV/AV)

5 VOL MODE

Turns on or off the volume modes (see page 52).

6 AUTO SETUP

Use to enter the AUTO SETUP menu (see page 27).

7 Numeric buttons

Use to enter numbers. (S: TV/AV)

8 STEREO

Use the playback sources in 2-channel stereo (see

page 46).

9 Sound field program buttons

Use to select sound field programs (see page 49).

0 CH LEVEL

Adjusts the volume level of each channel (see page 69).

A Cursor buttons / / / , ENTER

Use to select and adjust SET MENU items.

Use to select DVD menu items. (S: TV/AV)

B TEST

Outputs a test tone when adjusting the output level of each

speaker (see page 68).

C VOLUME +/–

Increases or decreases the volume level of this unit (see

page 39).

D MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level (see page 39).

E TV INPUT

Switches the input source or the TV (see page 78).

F DVD player/VCR control buttons

Use to control the DVD player or the VCR (see pages 78

and 79).

G My beam microphone

Use to collect the test tones from this unit when using the

my beam auto-adjust function (see page 48).

Remote control

POWER

STANDBY/ON

STEREO

MY BEAM

INPUT2

TV

21

SLEEP

CH LEVEL MENU

RETURN

TEST

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

ENTER

SURROUND

OFF

CODE SET

SPORTS

AV

3

4

56

789

0

+10

5BEAM

ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

INPUTMODE

MACROINPUT1

AUX

YSP

TV/AV

CH

TV

STB VCR DVD

CONTROLS AND FUNCTIONS

10 En

H TV POWER

Turns on the power of the TV or sets it to the standby

mode (see page 78).

I AV POWER

Turns on the power of the selected component or sets it to

the standby mode (see pages 78 and 79).

J INPUT1/INPUT2

Selects the input source of the TV (see page 78).

K MACRO

Use to set the TV macro (see page 80).

L SLEEP

Sets the sleep timer (see page 55).

M INPUTMODE

Switches between input modes (AUTO, DTS or

ANALOG). See page 71 for details.

N Beam mode buttons

Change the beam mode settings (see pages 40, 46 and 47).

O SURROUND

Selects the surround mode for playback (see page 40).

P MY BEAM

Use to select the my beam as the beam mode (see

page 48).

Q TruBass

Use to effectively reproduce the bass sound (see page 54).

R MENU

Displays the setup menu on your TV monitor (see

pages 29 and 58).

Displays the DVD menu. (S: TV/AV)

S Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating the

TV or other AV components set up the appropriate remote

control codes.

T RETURN

Use to select sleep timer settings or return to the previous

SET MENU screen.

Use to return to the previous DVD menu screen or exit the

DVD menu. (S: TV/AV)

U TV VOL +/–

Adjusts the volume level of the TV (see page 78).

V CH +/–

Switches between channels of the TV or the VCR (see

pages 78 and 79).

W TV MUTE, CODE SET

Mutes the audio output of the TV (see page 78).

Use to set up remote control codes (see page 77).

INSTALLATION

11 En

PREPARATION

English

This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.

This unit creates surround sound by reflecting projected

sound beams off the walls of your listening room. The

surround sound effects produced by this unit may not be

sufficient when the unit is installed in the following

locations.

• Rooms with surfaces inadequate for reflecting sound

beams

• Rooms with acoustically absorbent surfaces

• Rooms with measurements outside the following range

W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)

• Rooms with less than 1.8 m from the listening position

to the speaker positions

• Rooms where objects such as furniture are likely to

obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of

this unit

Make sure you leave an adequate amount of ventilation

space so that heat can escape. Make at least 5 cm of space

above or below this unit.

• We do not recommend installing this unit so that it is positioned

directly on the floor of your listening room. Please install this

unit using a metal wall bracket, rack or stand.

• This unit weighs 9.0 kg. Be sure to install this unit where it will

not fall subject to vibrations, such as from an earthquake, and

where it is out of the reach of children.

• When using a cathode-ray tube (CRT) TV, do not install this

unit directly above your TV.

• This unit is shielded against magnetic rays. However, if the

picture on your TV screen becomes blurred or distorted, we

recommend moving the speakers away from your TV.

Install this unit where there are no obstacles such as

furniture obstructing the path of sound beams. Otherwise,

the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the

corner.

Parallel installation

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

Corner installation

Install this unit in the corner at a 40º to 50º angle from the

adjacent walls.

INSTALLATION

Before installing this unit

Notes

5 cm or more

Rear

Front

Side view

Installing this unit

An object, such as furniture

40° to 50°

An object, such as furniture

12 En

INSTALLATION

■ Installation examples

Example 1

Install this unit as close to the exact center of the wall as possible.

Example 2

Install this unit so that the sound beams can be reflected off the walls.

Example 3

Install this unit as close to the exact front of your normal listening position.

13 En

INSTALLATION

PREPARATION

English

■ Using a metal wall bracket

You can use the optional metal wall bracket to mount this

unit on the wall in your listening room.

y

Refer to the instructions supplied with the metal bracket for

details on how to attach the metal bracket to the wall or how to

attach this unit to the metal bracket.

■ Using a stand

You can mount your TV on the stand placed on a

commercially available rack to install this unit under your

TV.

y

Refer to the instructions supplied with the stand for details on

how to install the stand or how to mount this unit and the TV on

the stand.

■ Using a rack

You can install this unit either above or under your TV in a

commercially available rack.

Make sure that the rack is large enough to allow adequate

ventilation space around this unit (see page 11) and that it is

strong enough to support the weight of both this unit and your TV.

■ Affixing this unit

Peel off the film from each of the four supplied fasteners

and then secure them to the bottom four corners of this

unit and the top of the rack, etc.

• Do not install this unit on top of a slanted surface. This unit may

fall over and cause injury.

• Make sure you wipe the surface of the rack, etc. before securing

the fasteners. Applying the tape to a dirty or wet surface will

weaken the sticking power of the tape, and this unit may fall as

a result.

This unit

TV

Metal wall bracket

TV

This unit

Stand

Note

Notes

When this unit is installed above your TV

When this unit is installed under your TV

1

2

This unit

Peel off

the film

Fasteners

CONNECTIONS

14 En

This unit is equipped with two optical digital jacks, one coaxial digital jack and two types of analog jacks for connecting

external components such as your TV, DVD player, VCR, digital satellite tuner, cable TV tuner and game console.

Further, by connecting a subwoofer to this unit, you can enjoy reinforced low bass sounds. For details on how to connect

various types of external components to this unit, see pages 15 to 20.

• Do not connect this unit or other components to the main power until all connections between components are

complete.

• Unplug the power supply cable before changing connections, moving or cleaning this unit.

CONNECTIONS

CAUTION

TV

This unit

Audio connection

Video connection

Digital satellite tuner, cable TV

tuner or game console

DVD player Subwoofer VCR

Optical fiber cable

To prevent cables from becoming unplugged, place the supplied

cable clamp with the open side facing upward, attach it to the rear

panel of this unit in a suitable position and then affix cables in the

cable clamp.

Attach to this unit

15 En

CONNECTIONS

PREPARATION

English

You can connect a TV to this unit and display the OSD for easy viewing when you adjust the system parameters in SET

MENU.

y

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 14).

If you connect this unit to the analog audio and optical digital audio output jacks at the same time as shown in the left illustration below,

the digital audio signals output at the optical digital output jack take priority over the analog audio signals output at the analog audio

output jacks.

■ Digital and analog audio connections

Cables used for connections

■ Video connections

Cables used for connections

Connecting a TV

Note

VCR

SUBWOOFER

TV/STB

AUDIO INPUT

OUT

OPTICAL

DIGITAL INPUT

TV/STB VIDEO

AUX

DVD

COAXIAL

Rear panel of this unit

TV

Analog audio

output

Optical digital

output

RL

Remove the caps if

attached

Check the direction

Optical cable (supplied)

Audio pin cable

(White)

(Red)

(White)

(Red)

VCR

SUBWOOFER

TV/STB

AUDIO INPUT

OUT

OPTICAL

DIGITAL INPUT

TV/STB VIDEO

AUX

DVD

COAXIAL

TV

Video

input

Rear panel of this unit

OSD video pin cable (supplied)

(Yellow)(Yellow)

16 En

CONNECTIONS

To connect a DVD player/recorder, connect the coaxial digital output jack on your DVD player to the coaxial digital

input jack (DVD COAXIAL) on this unit.

If there is no coaxial digital output jack on your DVD player/recorder, use them with optical digital connection.

y

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 14).

• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system

settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.

• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead.

Cables used for connections

Connecting a DVD player/recorder

Notes

VCR

SUBWOOFER

TV/STB

AUDIO INPUT

OUT

OPTICAL

DIGITAL INPUT

TV/STB VIDEO

AUX

DVD

COAXIAL

Rear panel of this unit

Video signal to a TV

Coaxial digital

output

Analog audio

output

Coaxial digital

output

L

R

DVD/VCR combo

player/recorder

DVD player/recorder

Video signal to a TV

Audio pin cable

(White)

(Red)

(White)

(Red)

Digital audio pin cable (supplied)

(Orange)(Orange)

17 En

CONNECTIONS

PREPARATION

English

To connect a VCR, connect the analog audio output jacks on your VCR to the analog audio input jacks (VCR R/L) on

this unit.

Connect red plugs to the right jacks and white plugs to the left jacks.

Cables used for connections

Connecting a VCR

VCR

SUBWOOFER

TV/STB

AUDIO INPUT

OUT

OPTICAL

DIGITAL INPUT

TV/STB VIDEO

AUX

DVD

COAXIAL

Video signal to a TV

Rear panel of this unit

Analog audio

output

R

L

VCR

Audio pin cable

(White)

(Red)

(White)

(Red)

18 En

CONNECTIONS

To connect a digital satellite tuner or a cable TV tuner, connect the optical digital output jack on your digital satellite

tuner or cable TV tuner to the optical digital input jack (TV/STB OPTICAL) on this unit. In addition, connect the analog

audio output jacks on your VCR to the analog audio input jacks (TV/STB R/L) on this unit.

Connect red plugs to the right jacks and white plugs to the left jacks.

y

To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 14).

If your TV and tuner connected to this unit do not support digital broadcasting, connect the analog audio output jacks (TV/STB R/L) on

this unit to the analog audio output jacks on your TV.

Cables used for connections

Connecting a digital satellite tuner or a cable TV tuner

Note

VCR

SUBWOOFER

TV/STB

AUDIO INPUT

OUT

OPTICAL

DIGITAL INPUT

TV/STB VIDEO

AUX

DVD

COAXIAL

Video signal to a TV

Rear panel of this unit

Digital satellite tuner or a cable TV tuner

Optical digital

output

Analog audio

output

L

R

Analog audio

output

L

R

TV

Optical cable (supplied)

Audio pin cable

(White)

(Red)

(White)

(Red)

Pagina se încarcă ...

Yamaha YSP-900 Manualul proprietarului

Yamaha YSP-900 Manualul proprietarului

în alte limbi

Lucrări conexe