Yamaha YST-MS35D Manualul proprietarului

Marca: Yamaha

Model: YST-MS35D

Categorie: Boxe soundbar

Tip: Manualul proprietarului

POWERED MULTIMEDIA SPEAKERS

YST-MS35D

UCA

OWNER’S MANUAL

MODE D’EMPLOI

SAFETY INSTRUCTIONS

Read Instructions — All the safety and operating

instructions should be read before the unit is oper-

ated.

Retain Instructions — The safety and operating

instructions should be retained for future reference.

Heed Warnings — All warnings on the unit and in

the operating instructions should be adhered to.

Follow Instructions — All operating and other

instructions should be followed.

Water and Moisture — The unit should not be used

near water – for example, near a bathtub, wash-

bowl, kitchen sink, laundry tub, in a wet basement,

or near a swimming pool, etc.

Carts and Stands — The unit should be used only

with a cart or stand that is recommended by the

manufacturer.

An unit and cart combination

should be moved with care. Quick

stops, excessive force, and

uneven surfaces may cause the

unit and cart combination to over-

turn.

Wall or Ceiling Mounting — The unit should be

mounted to a wall or ceiling only as recommended

by the manufacturer.

Ventilation — The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situ-

ated on a bed, sofa, rug, or similar surface, that may

block the ventilation openings; or placed in a built-in

installation, such as a bookcase or cabinet that may

impede the ﬂow of air through the ventilation open-

ings.

Heat — The unit should be situated away from heat

sources such as radiators, stoves, or other appli-

ances that produce heat.

Power Sources — The unit should be connected to

a power supply only of the type described in the

operating instructions or as marked on the unit.

Power-Cord Protection — Power-supply cords

should be routed so that they are not likely to be

walked on or pinched by items placed upon or

against them, paying particular attention to cords at

plugs, convenience receptacles, and the point

where they exit from the unit.

Cleaning — The unit should be cleaned only as rec-

ommended by the manufacturer.

Nonuse Periods — The power cord of the unit

should be unplugged from the outlet when left

unused for a long period of time.

Object and Liquid Entry — Care should be taken so

that objects do not fall into and liquids are not

spilled into the inside of unit.

Damage Requiring Service — The unit should be

serviced by qualiﬁed service personnel when:

The power-supply cord or the plug has been

damaged; or

Objects have fallen, or liquid has been spilled

into the unit; or

The unit has been exposed to rain; or

The unit does not appear to operate normally or

exhibits a marked change in performance; or

The unit has been dropped, or the enclosure

damaged.

Servicing — The user should not attempt service

the unit beyond those means described in the oper-

ating instructions. All other servicing should be

referred to qualiﬁed service personnel.

Power Lines — An outdoor antenna should be

located away from power lines.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert you to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

IMPORTANT!

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE.

iii

Grounding or Polarization — Precautions should be

taken so that the grounding or polarization is not

defeated.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party:

Address:

Telephone:

FAX:

Type of Equipment:

Model Name:

Yamaha Corporation of America

6600 Orangethorpe Ave.

Buena Park, CA90622

714-522-9011

714-527-5782

Powered Multimedia Speakers

YST-MS35D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most

out of your equipment by playing it at a safe level. One

that lets the sound come through loud and clear without

annoying blaring or distortion – and, most importantly,

without affecting your sensitive hearing.

Since hearing damage from loud sounds

is often undetectable until it is too late,

YAMAHA and the Electronic Industries

Association’s Consumer Electronics

Group recommend you to avoid prolonged

exposure from excessive volume levels.

FCC INFORMATION (U.S.A)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modiﬁcations

not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will

not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the

product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America 6600 Orangetho-

rpe Ave. Buena Park, CA90622, U.S.A.

FOR CANADIAN CUSTOMERS

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF PLUG TO WIDE SLOT AND FULLY INSERT.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH

CANADIAN ICES-003.

POUR LES CONSOMMATEURS CANADIENS

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRO-

DUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET

POUSSER JUSQU’AU FOND.

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME À LA NORME NMB-003 DU CANADA.

E-

Cautions

Please read the following operating precautions before use:

• When you disconnect the AC adaptor from the AC

outlet, hold the plug, not the cord.

• If you plan not to use the YST-MS35Ds for a

while, disconnect the AC adaptor from the AC out-

let.

• Always disconnect the AC adaptor from the AC

outlet before making any connections.

• The YST-MS35Ds do not contain any user service-

able parts. Refer all servicing to your Yamaha

dealer.

•

Never open the cabinet.

If a foreign object drops

into the set, contact your dealer, and do not use the

YST-MS35Ds. Otherwise, you may cause a ﬁre.

• Do not expose the YST-MS35Ds to temperature

extremes, direct sunlight, excessive dust, humidity,

or vibration.

• Position the YST-MS35Ds on a level, stable sur-

face. Do not drop the YST-MS35Ds, apply exces-

sive force to their controls, or put heavy items on

top of them.

• Do not place small metal objects on the speakers.

Otherwise, the object may fall, possibly causing an

injury.

• To protect the YST-MS35D speakers, avoid micro-

phone feedback, continuous and excessive output

from electronic musical instruments, and excessive

signal distortion.

• If the YST-MS35Ds are located close to ﬂuores-

cent or neon lights, a slight hum may be heard. In

this case, relocate the YST-MS35Ds away from the

light.

• Although the YST-MS35D speakers are magneti-

cally shielded, keep ﬂoppy disks and tapes away

from them.

• The YST-MS35Ds may cause picture distortion

when located close to a television or computer

monitor. In this case, move them away a short dis-

tance.

• Avoid sources of hum (transformers, motors). To

prevent ﬁre or electrical shock, do not expose to

rain and water.

• Do not use force on switches, knobs, or cables.

When you move the YST-MS35D, ﬁrst turn off the

power to the speakers, then disconnect the AC

adaptor from the AC outlet and the cables from the

connected devices.

• Always turn the volume control counterclockwise

to the minimum before starting to play the audio

source: increase the volume gradually to an appro-

priate level after the playback has started.

• Though this speaker is a magnetically shielded

type, there may be some inﬂuence on the monitor

picture depending on the type of monitor or the

placement of the speaker. In such a case, place the

speaker further apart from the monitor until there

is no inﬂuence on the monitor picture.

• When placing the provided AC adaptor on the

desk, etc., be sure to ﬁx the adaptor on the desk,

etc. to prevent it from falling. If the adaptor falls, it

may cause personal injury or damage to the adap-

tor and/or other equipment.

Table of Contents

Introducing the YST-MS35D Speaker System...... 1

Controls & Connectors............................................ 2

Installing USB driver............................................... 3

Microsoft Windows 98/98SE or Windows Me...... 4

Microsoft Windows 2000 Professional.................. 6

Macintosh computer............................................... 8

Connecting to a non-USB system............................8

Enjoying your YST-MS35D Speaker System........8

Adjusting the Volume, Bass, and Treble................8

Troubleshooting........................................................9

Speaker angle and Non skid pad...........................10

Specifications ..........................................................10

E-

English

Introducing the YST-MS35D Speaker System

Thank you for purchasing the Yamaha YST-MS35D Powered Multimedia Speakers.

The YST-MS35D Multimedia Speakers utilize Advanced Yamaha Active Servo Technology, which offers exception-

ally high performance, allowing these compact speakers to produce a rich bass sound. They also employ USB tech-

nology to create a computer-based listening environment that is far superior to conventional multimedia speakers.

They reproduce a clearer sound, with less noise and distortion, and never require a soundcard!

The YST-MS35D includes three speaker components: a left satellite speaker, a right satellite speaker, and a sub-

woofer.

Please inspect the package contents thoroughly for damage. If any item is missing or damaged, please contact the

dealer from whom you purchased the YST-MS35D.

3.5 mm stereo mini plug cable

1 (Accessory)

USB cable

1 (Accessory)

AC adaptor (PA-M30)

1 (Accessory)

• The package also contains eight non-skid pads to attach to the bottom of the satellite speakers.

Note:

Do not connect the PC using the USB cable before installing the USB driver.

Warning:

Be sure to use the included AC adaptor. Using another AC adaptor may damage the speakers or cause a ﬁre.

INPUT

USB

INPUT

TO RIGHT

SPEAKER

TO LEFT

SPEAKER BASS

010

DC 15V

INPUT

USB Cable

Face this marking

upward to connect

the USB cable to

the port.

LEFT

SATELLITE

SPEAKER

SUBWOOFER

AC adaptor

RIGHT

SATELLITE

SPEAKER

3.5 mm stereo mini plug cable

E-

Controls & Connectors

USB INPUT

Use the included USB cable to connect this port to

the USB port on the computer.

TO RIGHT SPEAKER

Connect the 8-pin cable from the right satellite

speaker to this connector.

INPUT 1/2

You can input two audio sources to the speaker

system from these input jacks. For example, you

can connect the output of a CD-ROM player and a

personal computer here. The two audio sources are

mixed together by the speaker system.

TO LEFT SPEAKER

Connect the RCA pin plug cable from the left sat-

ellite speaker to this connector.

BASS control

Allows you to adjust the volume level of the sub-

woofer.

A typical (recommended) setting is the position

between one o’clock and two o’clock.

Rotating the control clockwise will increase the

volume level, and rotating the control counter-

clockwise will decrease the level.

DC connector

Connect the included AC adaptor to this connector.

Press the (standby/on) button on the right satel-

lite speaker to turn the power on or standby.

VOLUME control

Allows you to adjust the volume level of the entire

speaker system.

Rotating the control clockwise will increase the

volume level, and rotating the control counter-

clockwise will decrease the level.

(standby/on) button/indicator

Press this button to turn on the power to the

speaker system. Its indicator lights up. Press the

button again to turn the speaker system to standby

mode.

Before pressing this button, make sure that the

VOLUME control setting is lowered. A small elec-

trical current ﬂows through the speaker system

even if the standby/on button is turned off.

VOLUME

INPUT

USB

INPUT

TO RIGHT

SPEAKER

TO LEFT

SPEAKER BASS

010

DC 15V

INPUT

2 3

4 5 6

Rear

(Subwoofer) (Right satellite speaker)

Top

E-

English

Installing USB driver

When connecting this unit and your computer with the

USB cable and controlling this unit from the computer,

you must install the following software on your com-

puter.

•

USB driver software

: Necessary for this unit to

communicate with your computer .......... Use the

software originally supplied with the OS (Operat-

ing System) running on your computer

This section explains how to install the software. The

installation method differs from the OS running on

your computer.

Refer to the instructions suitable for your OS below.

* This manual uses terms utilized by the English

operating system as shown on the computer moni-

tor. If the operating system you are using is in

another language, please replace the English terms

with the terms used in your computer’s operating

system.

Preparations before installation

• Make sure that the USB cable is not connected to

this unit and that your computer is not activated.

• Make sure that your computer meets the system

requirements listed below.

If your computer does not meet the system require-

ments, you can use the computer as an input

source by connecting it to the analog or digital

input(s) of this unit. In that case, however, the sup-

plied Application Software cannot be used.

• You may be requested to insert your OS’s CD-

ROM during the installation, so please have it

ready before commencing.

• The installing method may differ from the instruc-

tions below depending on the operating environ-

ment of your computer. In such a case, follow the

instructions shown on the monitor. If you still have

any question, inquire at the manufacturer of your

computer or a computer dealer.

System requirements

Your computer must meet the following system requirements to use the supplied Application Software.

Operating System

Microsoft Windows 98/98SE, Windows Me or Win-

dows 2000 Professional

Computer

A computer with a USB port as a standard equipment

and preinstalled with the above OS.

Windows is a registered trademark of Microsoft Corporation

in the United States and/or other countries.

Operating System

Mac OS 9.0.4 or greater (USB Driver 1.4 or greater)

Computer

Macintosh computer with a USB port as a standard

equipment

Macintosh is a trademark of Apple Computer, Inc., regis-

tered in the U.S. and other countries.

Microsoft Windows 98/98SE, Windows

Me or Windows 2000 Professional

Macintosh

E-

Installing the software

■

Installing and checking the USB driver

1. Turn on your computer and, if it’s not running

already, start Windows 98/98SE or Windows

Me.

2. Connect the power cord (or AC adaptor) to a

suitable AC outlet.

This unit can be on or in standby mode when

installing the driver.

3. Connect this unit to a USB port on the com-

puter using the supplied USB cable.

Windows automatically detects this unit and

installs the necessary driver software. Make opera-

tions as indicated in the dialog box. You may be

requested to insert your Windows OS CD-ROM.

* The installation may take a longer time depend-

ing on the system environment. After the instal-

lation dialog box disappears, wait several

minutes.

Check that the USB driver has been installed success-

fully by following the procedure below.

4. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

The Control Panel window appears.

5. Double-click the “System” icon.

The System Properties window appears.

6. Click the “Device Manager” tab.

The Device Manager window appears.

7. Click the “View devices by type” option button.

8. Click the “+” symbol next to “Sound, video and

game controllers,” and make sure that “USB

Audio Device” appears in the list, as shown.

* The screen image is for Windows 98SE.

* When using Windows Me, “?” may be shown at

the head of “USB Copmposite Device” in green.

This means the USB driver has been installed

with the Generic ID supplied with the operating

system. (This is not an error message.)

9. Click the “+” symbol next to “Human Interface

Devices”, and make sure that “HID-compliant

consumer control device” and “USB Human

Interface Device” appear in the list, as shown.

* The screen image is for Windows 98SE.

10. Click the “+” symbol next to “Universal Serial

Bus controllers” and make sure that “USB

Composite Device” appears in the list, as

shown.

* The screen image is for Windows 98SE.

Note:

• The device list on your computer may differ to that

shown here.

• If “!” or “?” is shown at the head of the device

name, check the followings:

* The USB cable is ﬁrmly connected.

* The AC power cord of this unit is plugged into

an AC outlet.

• If the driver has not been successfully installed,

disconnect the USB cable and connect it again.

Then try to install the driver again. If installation

still fails, restart Windows and try again.

Microsoft Windows 98/98SE or Windows Me

E-5

English

Make the following settings on your computer after the installation of the driver is ﬁnished.

Setting of Audio and Audio CD

[Windows 98/98SE only]

• Terminate all the activated applications.

• When using Windows 98SE, restart Windows,

ﬁrst.

1. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

2. Double-click the “Multimedia” icon.

3. Click the “Audio” tab and select “USB Audio

Device” at “Preferred device” of “Playback”.

* Usually, this setting is automatically made.

* If “USB Audio Device” does not appear, restart

Windows.

4. Click the “CD Music” tab and select the CD-

ROM drive for playing audio CDs.

5. Click the check box of “Enable digital CD audio

for this CD-ROM device” to enter the check

mark.

* It may happen that the check box cannot be

clicked because some CD-ROM drives cannot

be used for playing audio CDs.

6. Click “OK” and close the “Multimedia” setting

panel.

7. Restart Windows.

Note:

When using two or more drives, you must make

the above setting for each drive.

Checking the Audio setting

[Windows Me only]

1. Click the Windows Me “Start” button and

select “Settings”, and then “Control Panel”.

2. Double-click the “Sounds and Multimedia”

icon.

3. Click the “Audio” tab and select “USB Audio

Device” at “Preferred device” of “Sound Play-

back”.

* Usually, this setting is automatically made.

* If “USB Audio Device” does not appear, restart

Windows.

Checking sound output and adjusting volume

[Windows 98/98SE and Windows Me]

1. Make the following operations on the front

panel of this unit.

a) Press button to turn on this unit.

b) Use the volume control to adjust the volume.

2. Adjust the volume on the computer as follows.

a) Double-click the speaker icon on the task tray,

or select “Start”, “Programs”, “Accessories”,

“Entertainment” in this order and click “Vol-

ume Control”.

(The volume adjustment window appears.)

b) Adjust the volume by dragging the “Volume”

slider. Set the slider between the center and

max. positions.

* Do not enter the check mark in the “Mute”

check box. If entered, sound output will stop.

3. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

4. Double-click the “Sounds” (or “Sounds and

Multimedia”) icon.

5. Click the “Sounds” tab.

6. Check that the sound is output normally by out-

putting “Default sound”, etc. from “Events” (or

“Sound Events”).

* If no sound is heard, restart Windows and check

again.

E-6

■ Installing and checking the USB driver

1. Turn on your computer and, if it’s not running

already, start Windows 2000 Professional, and

2. Connect the power cord (or AC adaptor) to a

suitable AC outlet.

This unit can be on or in the standby mode when

installing the driver.

3. Connect this unit to a USB port on the com-

puter using the supplied USB cable.

Windows automatically detects this unit and

installs the necessary driver software.

* The installation may take a longer time depend-

ing on the system environment. After the dialog

box for installation disappears, wait several min-

utes.

Check that the USB driver has been installed success-

fully by following the procedure below.

4. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

The Control Panel window appears.

5. Double-click the “System” icon.

The System Properties window appears.

6. Select the “Hardware” tab, and click the

“Device Manager”.

The Device Manager window appears.

7. Select the “View” tab, and click the “Devices by

type” option button.

8. Click the “+” symbol next to “Sound, video and

game controllers,” and make sure that “USB

Audio Device” appears in the list, as shown.

9. Click the “+” symbol next to “Human Interface

Devices”, and make sure that “HID-compliant

consumer control device” and “USB Human

Interface Device” appear in the list, as shown.

10. Click the “+” symbol next to “Universal Serial

Bus controllers” and make sure that “USB

Composite Device” appears in the list, as

shown.

Note:

• The device list on your computer may differ to that

shown here.

• If “!” or “?” is shown at the head of the device

name, check the followings:

* The USB cable is ﬁrmly connected.

* The AC power cord of this unit is plugged into

an AC outlet.

• If the driver has not been successfully installed,

disconnect the USB cable and connect it again.

Then try to install the driver again. If installation

still fails, restart Windows and try again.

Microsoft Windows 2000 Professional

E-7

English

Make the following settings on your computer after the installation of the driver is ﬁnished.

Setting of Audio and Audio CD

1. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

2. Double-click the “Sounds and Multimedia”

icon.

3. Click the “Audio” tab and select “USB Audio

Device” at “Preferred device” of “Sound Play-

back”.

* Usually, this setting is automatically made.

4. Click the “Hardware” tab and double-click the

item of the DVD or CD-ROM to be used in the

“Devices”.

5. Click the “Properties” tab, and click the check

box of “Enable digital CD audio for this CD-

ROM device” to enter the check mark.

* It may happen that the check box cannot be

clicked because some CD-ROM drives cannot

be used for playing audio CDs.

6. Restart Windows, and log in with Administra-

tor.

Note:

When using two or more drives, you must make

the above setting for each drive.

Checking sound output and adjusting volume

1. Make the following operations on the front

panel of this unit.

a) Press button to turn on this unit.

b) Use the volume control to adjust the volume.

2. Adjust the volume on the computer as follows.

a) Double-click the speaker icon on the task tray,

or select “Start”, “Programs”, “Accessories”,

“Entertainment” in this order and click “Vol-

ume Control”.

(The volume adjustment window appears.)

b) Adjust the volume by dragging the “Volume”

slider. Set the slider between the center and

max. position.

* Do not enter the check mark in the “Mute”

check box. If entered, sound output will stop.

3. Click the Windows “Start” button and select

“Settings”, and then “Control Panel”.

4. Double-click the “Sounds and Multimedia”

icon.

5. Click the “Sounds” tab.

6. Check that the sound is output normally by out-

putting “Default Beep”, etc. from “Sound

Events”.

* If no sound is heard, restart Windows and check

again.

E-8

■ Connections and setup

1. Connect the power cord (or AC adaptor) to a

suitable AC outlet.

2. Start the Macintosh.

3. Connect this unit to a USB port on the com-

puter using the supplied USB cable.

The driver software for USB audio is automati-

cally installed.

4. Press button to turn on this unit.

Checking sound output and adjusting volume

1. Make the following operations on the front

panel of this unit.

a) Press button to turn on this unit.

b) Use the volume control to adjust the volume.

2. Check that the sound is output normally by out-

putting “Alert Sounds”, etc. from “Sound” on

the “Control Panels” on the Macintosh.

3. Adjust the volume by dragging the “Sound” tab

on the “Control Panels”. Set the tab between

the center and max. position.

Note:

• The sound output destination cannot be changed

from “Choose a device for sound output” on the

“Control Panels”. When using the internal speaker

of the Macintosh as the sound output destination,

disconnect the USB cable connecting this unit and

the Macintosh.

• When using headphones with this unit connected

to the USB port on the Macintosh, use the head-

phone jack on this unit, not the jack on the Macin-

tosh.

• Since the Macintosh issues a start-up sound at

power-on before the sound signal via the USB con-

nection is activated, the start-up sound cannot be

issued via the USB connection. To play the start-

up sound via this unit, you need a separate analog

connection between this unit and the Macintosh.

(When USB MIX is set to “ON” from the Setup

Panel of the Application Software, you can mix the

start-up sound via the analog connection with the

same sound via the USB connection without mak-

ing any change in the input selector settings.)

Connecting to a non-USB system

You can input analog audio signals into Inputs 1 and 2 (3.5 mm stereo mini plug input jacks) on the rear of sub-

woofer and use the YST-MS35D system like conventional multimedia speakers. (For example, you can connect the

outputs from a soundcard.)

Some games software does not support USB. In this case, instead of using the USB connection, connect Input 1 or 2

on the rear of subwoofer to the audio output jack on your computer using a 3.5 mm stereo mini plug cable, and spec-

ify your card type. (For move information on setting, consult your computer manual or computer dealer.)

Enjoying your YST-MS35D Speaker System

Adjusting the Volume, Bass, and Treble

First adjust the volume levels, bass, and treble using software controls (such as the Windows 98 Volume Control

panel). After adjustment, use the VOLUME control on the right speaker to set the volume level of the speakers.

Macintosh computer

E-9

English

Troubleshooting

Refer to the chart below if this system does not function properly. If the problem you are experiencing is not listed

below or if the instructions given below do not help, disconnect the AC adaptor and contact your authorized

YAMAHA dealer or service center.

Note 1: USB ports are delicate. Handle them with care. Do not insert USB plugs forcefully or you may damage the

port.

Note 2: For more information on issues related to OS, consult the your computer manual or your computer dealer.

PROBLEM CAUSE REMEDY

The speakers are

recognized as an

“unknown device”

by the computer.

The USB cable is not connected securely. Remove the USB cable from the speaker and computer,

then re-connect it securely. Also, turn off and on the power

to the speakers.

You did not complete the USB Driver

Install procedure correctly.

Turn off the power to the speakers, remove the USB cable,

then turn on the power to the speaker again. If the USB

Driver is still not recognized, re-install it.

No sound comes

from the speakers.

The AC adaptor is not properly plugged

into the AC outlet.

Insert the AC adaptor ﬁrmly into the AC outlet.

The (standby/on) button is turned off or

the AC adaptor is not plugged into the AC

outlet and the DC connector completely.

Plug the AC adaptor completely into the AC outlet and DC

connector, then turn on the (standby/on) button.

The volume is set to minimum. Turn the speaker VOLUME control to the right to increase

the volume.

The level of the input signal is too low. Turn up the volume on the connected device.

Connections are faulty or incomplete. Make the connections again, ﬁrmly, or use a different cable.

You are using a slow-speed USB cable. Make sure you use the USB cable included in the package

or an equivalent high-speed USB cable.

Playback sound is

interrupted.

Playback is affected by other open applica-

tions.

Close other open applications.

Sound is distorted. The level of the input signal is too high. Turn down the volume on the connected device.

Noise. Connections are faulty or incomplete. Make the connections again, ﬁrmly, or use a different cable.

E-10

Speaker angle and Non skid pad

You can adjust the speaker angle. Loosen the

screw on the bottom of the speaker stand as

shown in the ﬁgure, adjust the angle of the

stand, and tighten the screw to ﬁx the stand.

To prevent the speakers from sliding around,

attach the supplied pads to the four points on the

bottom of each satellite speaker. Place the

speaker on a stable, ﬂat surface.

Speciﬁcations

Type Advanced Yamaha Active Servo Technology

Driver Satellite ....................................5 cm (2") cone, magnetic shielding

Subwoofer................................12 cm (5") cone, magnetic shielding

Output power Satellite ....................................6 W + 6 W (1 kHz, 4Ω at T.H.D.=10%)

Subwoofer................................18 W (100 Hz, 4Ω at T.H.D.=10%)

Input sensitivity 200 mV (1 kHz, 4Ω at 6 W)

Input impedance 20 kΩ

Frequency response 45 Hz to 20 kHz (Satellite + Subwoofer)

Crossover Frequency Satellite/Subwoofer 180 Hz

Input jack 3.5 mm stereo mini jack for audio-signal × 2

USB digital × 1

Power supply U.S.A. and Canada models......AC 120 V, 60 Hz

(AC adaptor) Australia model........................AC 240 V, 50 Hz

U.K. and Europe models..........AC 230 V, 50 Hz

Dimensions (W × H × D) Satellite speakers......................65 (2.6") × 75 (3") × 119 (4.7") mm

Subwoofer................................183 (7.2") × 196 (7.7") × 183 (7.2") mm

Weight Satellite speakers......................Right: 0.45 kg (1 lb.), Left: 0.36 kg (13 oz.)

Subwoofer................................2.3 kg (5 lbs. 1 oz.)

Accessories AC adaptor (PA-M30) × 1

3.5 mm stereo mini plug cable × 1 (1.8 m)

USB cable × 1 (2 m)

8 pcs of non skid pads × 1 set

* Speciﬁcations subject to change without notice.

Please contact an authorized Yamaha dealer for more information on this product or connections to your computer.

* Non skid

pad

Speaker stand

Loosen Tighten

Printed in China

V770380

Yamaha YST-MS35D Manualul proprietarului

Marca: Yamaha

Model: YST-MS35D

Categorie: Boxe soundbar

Tip: Manualul proprietarului

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha YST-MS35D El kitabı
français: Yamaha YST-MS35D Le manuel du propriétaire
čeština: Yamaha YST-MS35D Návod k obsluze
русский: Yamaha YST-MS35D Инструкция по применению
English: Yamaha YST-MS35D Owner's manual
suomi: Yamaha YST-MS35D Omistajan opas
polski: Yamaha YST-MS35D Instrukcja obsługi
Deutsch: Yamaha YST-MS35D Bedienungsanleitung
italiano: Yamaha YST-MS35D Manuale del proprietario
español: Yamaha YST-MS35D El manual del propietario
svenska: Yamaha YST-MS35D Bruksanvisning
dansk: Yamaha YST-MS35D Brugervejledning
português: Yamaha YST-MS35D Manual do proprietário
Nederlands: Yamaha YST-MS35D de handleiding

Yamaha YST-MS35D Manualul proprietarului

Yamaha YST-MS35D Manualul proprietarului

în alte limbi

Lucrări conexe