Yamaha YST-SW315 Manualul proprietarului

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Indonesia WB35950

G

YST-SW315

YST-SW215

YST-SW315/YST-SW215

Subwoofer System

Enceinte a caisson de grave

OWNER S MANUAL

MODE D EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

1

Thank you for selecting this YAMAHA subwoofer system.

Please read the following operating precautions

before use. YAMAHA will not be held responsible

for any damage and/or injury caused by not　

following the cautions below.

• To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

• Install this unit in a cool, dry, clean place - away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical

shock, do not expose this unit to rain or water.

• Never open the cabinet. If something drops into the set,

contact your dealer.

• The voltage to be used must be the same as that specified

on the rear panel. Using this unit with a higher voltage

than specified is dangerous and may cause a fire and/or

electric shock.

• To reduce the risk or fire or electric shock, do not expose

this unit to rain or moisture.

• Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the power

plug and the wires connected to other equipments.

Never pull the wires themselves.

• When not planning to use this unit for a long period (ie.,

vacation, etc.), disconnect the AC power plug from the

wall outlet.

• To prevent lightning damage, disconnect the AC power

plug when there is an electric storm.

• Since this unit has a built-in power amplifier, heat will

radiate from the rear panel. Place the unit apart from the

walls, allowing at least 20 cm of space above, behind and

on both sides of the unit to prevent fire or damage.

Furthermore, do not position with the rear panel facing

down on the floor or other surfaces.

• Do not cover the rear panel of this unit with a newspaper,

a tablecloth, a curtain, etc. in order not to obstruct heat

radiation. If the temperature inside the unit rises, it may

cause fire, damage to the unit and/or personal injury.

• Do not place the following objects on this unit:

Glass, china, small metallic etc.

If glass etc. falls by vibrations and breaks, it may cause

bodily injury.

A burning candle etc.

If the candle falls by vibrations, it may cause fire and

bodily injury.

A vessel with water in it

If the vessel falls by vibrations and water spills, it may

cause damage to the speaker, and/or you may get an

electric shock.

• Do not place this unit where foreign objects such as

water drips might fall. It might cause a fire, damage to

this unit, and/or personal injury.

• Never put a hand or a foreign object into the YST port

located on the right side of this unit. When moving this

unit, do not hold the port as it might cause personal

injury and/or damage to this unit.

• Never place a fragile object near the YST port of this

unit. If the object falls or drops by the air pressure, it may

cause damage to the unit and/or personal injury.

• Never open the cabinet. It might cause an electric shock

since this unit uses a high voltage. It might also cause

personal injury and/or damage to this unit.

• When using a humidifier, be sure to avoid condensation

inside this unit by allowing enough spaces around this

unit or avoiding excess humidification. Condensation

might cause a fire, damage to this unit, and/or electric

shock.

• Super-bass frequencies reproduced by this unit may

cause a turntable to generate a howling sound. In such a

case, move this unit away from the turntable.

• This unit may be damaged if certain sounds are

continuously outputted at high volume level. For

example, if 20 Hz-50 Hz sine waves from a test disc,

bass sounds from electronic instruments, etc. are

continuously outputted, or when the stylus of a turntable

touches the surface of a disc, reduce the volume level to

prevent this unit from being damaged.

• If you hear distorted noise (i.e., unnatural, intermittent

“rapping” or “hammering” sounds) coming from this

unit, reduce the volume level. Extremely loud playing of

a movie soundtrack’s low frequency, bass-heavy sounds

or similarly loud popular music passages can damage

this speaker system.

• Vibration generated by super-bass frequencies may

distort images on a TV. In such a case, move this unit

away from the TV set.

• Do not attempt to clean this unit with chemical solvents

as this might damage the finish. Use a clean, dry cloth.

• Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding

that the unit is faulty.

• Secure placement or installation is the owner’s

responsibility. YAMAHA shall not be liable for any

accident caused by improper placement or

installation of speakers.

CAUTION: Read this before operating your unit

YST-SW315_215_03.25_tab.fm Page 1 Friday, April 4, 2003 1:20 PM

2

English

• VOLTAGE SELECTOR

(For China, Korea and General models)

The voltage selector switch on the rear panel of this

unit must be set for your local main voltage BEFORE

plugging this unit into the AC main supply. Voltages

are 110/120/220/240 V AC, 50/60 Hz.

For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous

if engaged in a live socket outlet.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

CAUTION ......................................................................1

FEATURES ....................................................................3

SUPPLIEDACCESSORIES ...........................................3

PLACEMENT ................................................................4

CONNECTIONS ...........................................................5

Connecting to line output (pin jack) terminals

of the amplifier .................................................... 5

Connecting to speaker output terminals of

the amplifier .......................................................... 8

Connecting to the INPUT1/ OUTPUT terminals

of the subwoofer .......................................................12

Plug in the subwoofer to the AC outlet ....................12

CONTROLSANDTHEIRFUNCTIONS ..................13

AUTOMATICPOWER-SWITCHING

FUNCTION .................................................................15

ADJUSTINGTHESUBWOOFER

BEFOREUSE .............................................................16

Frequency characteristics .........................................17

ADVANCEDYAMAHAACTIVESERVO

TECHNOLOGY ..........................................................18

TROUBLESHOOTING...............................................19

SPECIFICATIONS.......................................................2 0

Standby mode

When this unit is turned off by pressing the

STANDBY/ON button on the front panel, this unit

consumes a small amount of power. This state is called

the standby mode. This unit’s power supply is

completely cut off from the AC line only when the

POWER switch on the rear panel is set in the OFF

position or the AC power cord is disconnected.

This unit features a magnetically shielded design, but

there is still a chance that placing it too close to a TV

set might impair picture color. Should this happen,

move this unit away from the TV set.

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows: The wire which is coloured

BLUE must be connected to the terminal which is

marked with the letter N or coloured BLACK. The

wire which is coloured BROWN must be connected

to the terminal which is marked with the letter L or

coloured RED. Making sure that neither core is

connected to the earth terminal of the three pin plug.

For Canadian Customers

To prevent electric shock, match wide blade of plug

to wide slot and fully insert.

This Class B digital apparatus complies with

Canadian ICES-003.

CONTENTS

1

2

YST-SW315_215_03.25_tab.fm Page 2 Tuesday, March 25, 2003 4:07 PM

3

• This subwoofer system employs Advanced Yamaha

Active Servo Technology which Yamaha has developed

for reproducing higher quality super-bass sound. (Refer

to page 18 for details on Advanced Yamaha Active

Servo Technology.) This super-bass sound adds a more

realistic, theater-in-the-home effect to your stereo

system.

• This subwoofer can be easily added to your existing

audio system by connecting to either the speaker

terminals or the line output (pin jack) terminals of the

amplifier.

• For the effective use of the subwoofer, the subwoofer’s

super-bass sound should be matched to the sounds of

your main speakers. You can create the best sound

quality for various listening conditions by using the

HIGH CUT control and the PHASE switch.

• The Automatic power-switching function saves you the

trouble of pressing the STANDBY/ON button to turn the

power on and off.

• You can select bass effect suitable for the source by

using the B.A.S.S. button.

After unpacking, check that the following parts are

contained.

Non-skid pads

FEATURES

QD-Bass Technology

QD-Bass (Quatre Dispersion Bass) technology uses

square, pyramid-shaped reflective plates to radiate the

sound in four horizontal directions.

SUPPLIED ACCESSORIES

YST-SW315_215_03.25_tab-c.fm Page 3 Tuesday, April 15, 2003 11:02 AM

4

English

( : subwoofer, : main speaker)

One subwoofer will have a good effect on your audio

system, however, the use of two subwoofers is

recommended to obtain more effect.

If using one subwoofer, it is recommended to place it on

the outside of either the right or the left main speaker. (See

fig. .) If using two subwoofers, it is recommended to

place them on the outside of each main speaker. (See

fig. .) The placement shown in fig. is also possible,

however, if the subwoofer system is placed directly facing

the wall, the bass effect may die because the sound from it

and the sound reflected by the wall may cancel out each

other. To prevent this from happening, face the subwoofer

system at an angle as in fig. or .

Note

There may be a case that you cannot obtain enough super-

bass sounds from the subwoofer when listening in the

center of the room. This is because “standing waves” have

been developed between two parallel walls and they cancel

the bass sounds.

In such a case, face the subwoofer obliquely to the wall. It

also may be necessary to break up the parallel surfaces by

placing bookshelves etc. along the walls.

Use the non-skid pads

Put the provided non-skid pads at the four corners on the

bottom of the subwoofer to prevent the subwoofer from

moving by vibrations etc.

PLACEMENT

A

B

C

A

B C

A

B

YST-SW315_215_03.25_tab.fm Page 4 Tuesday, March 25, 2003 4:07 PM

5

Choose one of the following two connecting methods that is more suitable for your audio

system.

■

Choose (pages 5-7) if your amplifier has line output (pin jack) terminal(s)

■ Choose (pages 8-11) if your amplifier has no line output (pin jack)

terminal

Caution: Unplug the subwoofer and other audio/video components before making

connections.

Notes

• All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the

owner’s manual of your component to be connected to the subwoofer.

• After all connections are completed, plug in the subwoofer and other audio/video components.

• To connect with a YAMAHA DSP amplifier (or AV receiver), connect the SUBWOOFER (or LOW PASS etc.)

terminal on the rear of the DSP amplifier (or AV receiver) to the /MONO INPUT2 terminal of the subwoofer.

• When connecting the subwoofer to the SPLIT SUBWOOFER terminals on the rear of the DSP amplifier, be sure to

connect the /MONO INPUT2 terminal to the “L” side and the INPUT2 terminal to the “R” side of the SPLIT

SUBWOOFER terminals.

Notes

• Some amplifiers have line output terminals labeled PRE OUT. When you connect the subwoofer to the PRE OUT

terminals of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier has

only one set of PRE OUT terminals, do not connect the subwoofer to the PRE OUT terminals. Instead, connect the

subwoofer to the speaker output terminals of the amplifier. (Refer to pages 8-11.)

• When connecting to a monaural line output terminal of the amplifier, connect the /MONO INPUT2 terminal.

• When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT

terminals on the rear panel of the subwoofer. If connected, they will not produce sound.

CONNECTIONS

1

2

Connecting to line output (pin jack) terminals of the amplifier

1

L

R

L

YST-SW315_215_03.25_tab.fm Page 5 Tuesday, March 25, 2003 4:07 PM

6

English

■ Using one subwoofer

<YST-SW315>

<YST-SW215>

CONNECTIONS

Subwoofer

Amplifier

To AC outlet

Mono pin cable

(not included)

Audio pin cable

(not included)

Subwoofer

Amplifier

To AC outlet

Mono pin cable

(not included)

Audio pin cable

(not included)

YST-SW315_215_03.25_tab.fm Page 6 Tuesday, March 25, 2003 4:07 PM

7

■ Using two subwoofers

<YST-SW315>

<YST-SW215>

CONNECTIONS

Amplifier

To AC outlet

Mono pin cable

(not included)

Mono pin cable

(not included)

Amplifier

To AC outlet To AC outlet

Mono pin cable

(not included)

Mono pin cable

(not included)

YST-SW315_215_03.25_tab.fm Page 7 Tuesday, March 25, 2003 4:07 PM

8

English

Select this method if your amplifier has no line output (pin jack) terminal.

If your amplifier has two sets of main speaker output terminals and both terminals can output

sound signals simultaneously.

• Connect one set of main speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and

connect the other set of main speaker output terminals of the amplifier to the main speakers.

• Set the amplifier so that both sets of main speaker output terminals output sound signals simultaneously.

Note

• If your amplifier has only one set of main speaker output terminals, see page 10.

■ Using one subwoofer (with speaker cables)

<YST-SW315>

<YST-SW215>

CONNECTIONS

Connecting to speaker output terminals of the amplifier

2

Right main speaker Subwoofer

To AC outlet

Left main speaker

Amplifier

Speaker output

terminals

Amplifier

Right main speaker

Left main speaker

Subwoofer

To AC outlet

Speaker output

terminals

YST-SW315_215_03.25_tab-c.fm Page 8 Tuesday, April 15, 2003 1:44 PM

9

■ Using two subwoofers (with speaker cables)

<YST-SW315>

<YST-SW215>

CONNECTIONS

Right main speaker

Subwoofer

To AC outlet

Left main speaker

Amplifier

Speaker output

terminals

To AC outlet

Subwoofer

Amplifier

Right main speaker

Left main speaker

Subwoofer

To AC outlet

Subwoofer

Speaker output

terminals

YST-SW315_215_03.25_tab.fm Page 9 Tuesday, March 25, 2003 4:07 PM

10

English

If your amplifier has only one set of main speaker output terminals.

Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the

OUTPUT terminals of the subwoofer to the main speakers.

■ Using one subwoofer (with speaker cables)

<YST-SW315>

<YST-SW215>

CONNECTIONS

Right main speaker

Left main speaker

Subwoofer

Amplifier

Speaker output

terminals

To AC outlet

Right main speaker

Left main speaker

Subwoofer

Amplifier

Speaker output

terminals

To AC outlet

YST-SW315_215_03.25_tab.fm Page 10 Tuesday, March 25, 2003 4:07 PM

11

■ Using two subwoofers (with speaker cables)

<YST-SW315>

<YST-SW215>

CONNECTIONS

Right main speaker

Left main speaker

Subwoofer

Speaker output

terminals

To AC outlet To AC outlet

Amplifier

Right main speaker

Left main speaker

Subwoofer

Speaker output

terminals

To AC outlet

Amplifier

Subwoofer

YST-SW315_215_03.25_tab.fm Page 11 Tuesday, March 25, 2003 4:07 PM

12

English

For connection, keep the speaker cables as short as

possible. Do not bundle or roll up the excess part of the

cables. If the connections are faulty, no sound will be heard

from the subwoofer or the speakers, or both of them. Make

sure that the + and – polarity markings of the speaker

cables are observed and set correctly. If these cables are

reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other, because

this could damage the subwoofer or the amplifier, or both of

them.

■ Before connecting

Remove the insulation coating at the extremity of each

speaker cable by twisting the coating off.

■ How to connect:

<YST-SW315>

1 Loosen the terminal’s knob, as shown in the figure.

2 Insert the bare wire.

3 Tighten the knob.

4 Test the firmness of the connection by pulling lightly

on the cable at the terminal.

U.S.A., Canada and Australia models only

Banana Plug conection are also possible.

1 Tighten the terminal knob.

2 Simply insert the banana plug into the terminal.

<YST-SW215>

1 Press and hold the terminal’s tab, as shown in the

figure.

2 Insert the bare wire.

3 Release your finger from the tab to allow it to lock

securely on the cable’s wire end.

4 Test the firmness of the connection by pulling lightly

on the cable at the terminal.

After all connections are completed, plug in the subwoofer

and other audio/video components to the AC outlet.

<YST-SW315>

<YST-SW215>

CONNECTIONS

Connecting to the INPUT1/OUTPUT

terminals of the subwoofer

Good

No Good

Red: positive (+)

Black: negative (

–

)

Plug in the subwoofer to the AC outlet

Red: positive (+)

Black: negative (

–

)

To AC outlet

YST-SW315_215_03.25_tab.fm Page 12 Tuesday, March 25, 2003 4:07 PM

13

<YST-SW315>

<YST-SW215>

CONTROLS AND THEIR FUNCTIONS

Front panel

Rear panel

(General model)

Front panel

Rear panel

(General model)

YST-SW315_215_03.25_tab.fm Page 13 Tuesday, March 25, 2003 4:07 PM

14

English

1 Power indicator

Lights up in green while the subwoofer is on.

Lights up in red while the subwoofer is set in the

standby mode by the operation of the automatic power-

switching function.

Goes off when the subwoofer is set in the standby

mode.

2 STANDBY/ON button

Press this button to turn on the power when the

POWER switch is set in the ON position. (The power

indicator lights up in green.)

Press again to set the subwoofer in the standby mode.

(The power indicator goes off.)

3 B.A.S.S. (Bass Action Selector System) button

When this button is pressed in to the MUSIC position,

the bass sound in audio software is well reproduced.

By pressing the button again so that it pops out at the

MOVIE position, the bass sound in video software is

well reproduced.

4 HIGH CUT control

Adjusts the high frequency cut off point.

Frequencies higher than the frequency selected by this

control are all cut off (and no output).

* One graduation of this control represents 10 Hz.

5 VOLUME control

Adjusts the volume level. Turn the control clockwise to

increase the volume, and counterclockwise to decrease

the volume.

6 VOLTAGE SELECTOR switch

(China, Korea and General models only)

If the preset setting of the switch is incorrect, set the

switch to the proper voltage (110V, 120V, 220V or

240V) of your area.

Consult your dealer if you are unsure of the correct

setting.

WARNING

Be sure to unplug the subwoofer before setting the

VOLTAGE SELECTOR switch correctly.

7 POWER switch

Normally, set this switch to the ON position to use the

subwoofer. In this state, you can turn on the subwoofer

or turn the subwoofer into the standby mode by

pressing the STANDBY/ON button. Set this switch to

the OFF position to completely cut off the subwoofer’s

power supply from the AC line.

8 OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the main speakers.

Signals from the INPUT1 terminals are sent to these

terminals.

(Refer to “CONNECTIONS” for details.)

9 INPUT1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

(Refer to “CONNECTIONS” for details.

0 INPUT2 terminals

Used to input line level signals from the amplifier.

(Refer to “CONNECTIONS” for details.)

A AUTO STANDBY (HIGH/LOW/OFF) switch

This switch is originally set to the OFF position. By

setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as described on page 15. If you do not need

this function, leave this switch in the OFF position.

* Make sure to change the setting of this switch only

when the subwoofer is set in the standby mode by

pressing the STANDBY/ON button.

B PHASE switch

Normally this switch is to be set to the REV (reverse)

position. However, according to your speaker systems

or the listening condition, there may be a case when

better sound quality is obtained by setting this switch

to the NORM (normal) position. Select the better

position by monitoring the sound.

CONTROLS AND THEIR FUNCTIONS

Standby mode

The subwoofer is still using a small amount of

power in this mode.

YST-SW315_215_03.25_tab.fm Page 14 Tuesday, March 25, 2003 4:07 PM

15

If the source being played is stopped and the input signal is

cut off for 7 to 8 minutes, the subwoofer automatically

switches to the standby mode. (When the subwoofer

switches to the standby mode by the automatic power-

switching function, the power indicator lights up in red.)

When you play a source again, the power of the subwoofer

turns on automatically by sensing audio signals input to the

subwoofer.

This function operates by sensing a certain level of low

frequency input signal. Usually set the AUTO STANDBY

switch to the LOW position. However, if this function does

not operate smoothly, set the switch to the HIGH position.

In the HIGH position, the power will turn on even with a

low level of input signal. But please be aware that the

subwoofer may not switch to the standby mode when there

is an extremely low input signal.

* The power might turn on unexpectedly by sensing noise

from other appliances. If that occurs, set the AUTO

STANDBY switch to the OFF position and use the

STANDBY/ON button to switch the power between on

and to the standby mode manually.

This function detects the low-frequency components

below 200 Hz of the input signals (i.e., the explosion in

the action movie, the sound of the bass guitar or the bass

drum, etc.).

* The minutes required to switch the subwoofer to the

standby mode might change by sensing noise from other

appliances.

This function is available only when the power of the

subwoofer is on (by pressing the STANDBY/ON

button).

AUTOMATIC POWER-SWITCHING FUNCTION

YST-SW315_215_03.25_tab.fm Page 15 Tuesday, March 25, 2003 4:07 PM

16

English

Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer

and the main speakers by following the procedures described below.

<YST-SW315>

<YST-SW215>

1 Set the VOLUME control to minimum (0).

2 Turn on the power of all the other components.

3 Make sure that the POWER switch is set to the ON

position, then press the STANDBY/ON button to turn

on the subwoofer.

* The Power indicator lights up in green.

4 Play a source containing low-frequency components

and adjust the amplifier’s volume control to the desired

listening level.

5 Adjust the HIGH CUT control to the position where

the desired response can be obtained.

Normally, set the control to the level a little higher than

the main speaker’s rated minimum reproducible

frequency*.

* The main speaker’s rated minimum reproducible

frequency can be looked up in the speakers’ catalog

or owner’s manual.

6 Increase the volume gradually to adjust the volume

balance between the subwoofer and the main speakers.

Normally, set the control to the level where you can

obtain a little more bass effect than when the

subwoofer is not used. If the desired response cannot

be obtained, adjust the HIGH CUT control and the

VOLUME control again.

7 Set the PHASE switch to the position which gives you

the better bass sound.

Normally, set the switch to the REV (reverse) position.

If the desired response cannot be obtained, set the

switch to the NORM (normal) position.

8 Select “MOVIE” or “MUSIC” according to the played

source.

MOVIE:

When a movie type source is played, the low-

frequency effects are enhanced to allow the listeners

enjoy more powerful sound. (The sound will be thicker

and deeper.)

MUSIC:

When an ordinary music source is played, the

excessive low-frequency components are cut off to

make the sound clearer. (The sound will be lighter and

reproduces the melody line more clearly.)

• Once the volume balance between the subwoofer and

the main speakers is adjusted, you can adjust the

volume of your whole sound system by using the

amplifier’s volume control.

However, if you change the main speakers to others,

you must make this adjustment again.

• For adjusting the VOLUME control, the HIGH CUT

control and the PHASE switch, refer to “Frequency

characteristics” on page 17.

ADJUSTING THE SUBWOOFER BEFORE USE

YST-SW315_215_03.25_tab.fm Page 16 Tuesday, March 25, 2003 4:07 PM

17

This subwoofer’s frequency characteristics

<YST-SW315> <YST-SW215>

The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer

is combined with a typical main speaker system.

■ EX.1 When combined with a 4” or 5” (10 cm or 13 cm) acoustic suspension, 2 way system main

speakers

■ EX.2 When combined with an 8” or 10” (20 cm or 25 cm) acoustic suspension, 2 way system main

speakers

ADJUSTING THE SUBWOOFER BEFORE USE

Frequency characteristics

<YST-SW315>

PHASE :

Set to the

REV(reverse) position

<YST-SW215>

PHASE :

Set to the

REV(reverse) position

<YST-SW315>

PHASE :

Set to the

REV(reverse) position

<YST-SW215>

PHASE :

Set to the

REV(reverse) position

20 50 100 200 500Hz

40

50

60

70

80

90

dB

HIGH CUT 90 Hz

HIGH CUT 140 Hz

HIGH CUT 40 Hz

20 50 100 200 500Hz

40

50

60

70

80

90

dB

HIGH CUT 40 Hz

HIGH CUT 140 Hz

HIGH CUT 90 Hz

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-SW315

Main

speaker

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-SW215

Main

speaker

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-SW315

Main

speaker

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-SW215

Main

speaker

YST-SW315_215_03.25_tab.fm Page 17 Tuesday, March 25, 2003 4:07 PM

18

English

The theory of Yamaha Active Servo Technology has been

based upon two major factors, the Helmholtz resonator and

negative-impedance drive. Active Servo Processing

speakers reproduce the bass frequencies through an “air

woofer”, which is a port or opening in the speaker’s

cabinet. This opening is used instead of, and performs the

functions of, a woofer in a conventionally designed

speaker system. Thus, signals of low amplitude within the

cabinet can, according to the Helmholtz resonance theory,

be outputted from this opening as waves of great amplitude

if the size of the opening and the volume of the cabinet are

in the correct proportion to satisfy a certain ratio.

In order to accomplish this, moreover, the amplitudes

within the cabinet must be both precise and of sufficient

power because these amplitudes must overcome the “load”

presented by the air that exists within the cabinet.

Thus it is this problem that is resolved through the

employment of a new design in which the amplifier

supplies special signals. If the electrical resistance of the

voice coil could be reduced to zero, the movement of the

speaker unit would become linear with respect to signal

voltage. To accomplish this, a special negative-impedance

output-drive amplifier for subtracting output impedance of

the amplifier is used.

By employing negative-impedance drive circuits, the

amplifier is able to generate precise, low-amplitude, low-

frequency waves with superior damping characteristics.

These waves are then radiated from the cabinet opening as

high-amplitude signals. The system can, therefore, by

employing the negative-impedance output drive amplifier

and a speaker cabinet with the Helmholtz resonator,

reproduce an extremely wide range of frequencies with

amazing sound quality and less distortion.

The features described above, then, are combined to be the

fundamental structure of the conventional Yamaha Active

Servo Technology.

Our new Active Servo Technology, Advanced Yamaha

Active Servo Technology, adopted Advanced Negative

Impedance Converter (ANIC) circuits, which allows the

conventional negative impedance converter to dynamically

vary in order to select an optimum value for speaker

impedance variation. With this new ANIC circuits,

Advanced Yamaha Active Servo Technology can provide

more stable performance and improved sound pressure

compared with the conventional Yamaha Active Servo

Technology, resulting in more natural and dynamic bass

reproduction.

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY

High-amplitude

bass sound

Port

Cabinet

Advanced Negative-

impedance Converter

Active Servo

Processing

Amplifier

Signals of low amplitude

Air woofer

(Helmholtz resonator)

Signals

YST-SW315_215_03.25_tab.fm Page 18 Tuesday, March 25, 2003 4:07 PM

19

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer

or service center.

TROUBLESHOOTING

Problem Cause What to Do

Power is not supplied even though the

STANDBY/ON button is set to the ON

position.

The power plug is not securely

connected.

Connect it securely.

The POWER switch is set to the OFF

position.

Set the POWER switch to the ON

position.

No sound. The volume is set to minimum. Raise the volume up.

Speaker cables are not connected

securely.

Connect them securely.

Sound level is too low. Speaker cables are not connected

correctly.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and

“

–” to “–”.

Setting of the PHASE switch is not

proper.

Set the PHASE switch to the other

position.

A source sound with few bass

frequencies is played.

Play a source sound with bass

frequencies.

Set the HIGH CUT control to a higher

position.

It is influenced by standing waves. Reposition the subwoofer or break up

the parallel surface by placing

bookshelves etc. along the walls.

The subwoofer does not turn on

automatically.

The POWER switch is set to the OFF

position.

Set the POWER switch to the ON

position.

The STANDBY/ON button is set to the

OFF position.

Set the STANDBY/ON button to the ON

position.

The AUTO STANDBY switch is set to

the OFF position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

The level of input signal is too low. Set the AUTO STANDBY switch to the

“HIGH” position.

The subwoofer does not turn into the

standby mode automatically.

There is an influence of noise generated

from external appliances etc.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

The AUTO STANDBY switch is set to

the OFF position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

The subwoofer turns into the standby

mode unexpectedly.

The level of input signal is too low. Set the AUTO STANDBY switch to the

“HIGH” position.

The subwoofer turns on unexpectedly. There is an influence of noise generated

from external appliances etc.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

YST-SW315_215_03.25_tab.fm Page 19 Tuesday, March 25, 2003 4:07 PM

Pagina se încarcă ...

Yamaha YST-SW315 Manualul proprietarului

Acest manual este potrivit și pentru

Yamaha YST-SW315 Manualul proprietarului

în alte limbi

Lucrări conexe