Yamaha CRW-2100SX Manual de utilizare

Marca: Yamaha

Model: CRW-2100SX

Categorie: Unități de disc optice

Tip: Manual de utilizare

Acest manual este potrivit și pentru

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Corporation of America

Address: 6600 Orangethorpe Ave.

Buena Park, CA 90620

Telephone: 714-522-9011

Fax: 714-228-3913

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW2100SX

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is found to be the source of interference, which can be determined

by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America,

6600 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

FCC INFORMATION

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 780-787 nm

Pulse Durations and Max. Output

at the lens of the Laser Pickup Unit

Read Mode: 0.7mW (Continuous)

Write Mode: Max. 38mW

(for 166ns, Min. Cycle 86.6ns)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

LASER INFORMATION

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 780-787 nm

Impulsdauer und max. Ausgang an der Linse der

Laser-Abtasteinheit

Lesemodus: 0,7mW (kontinuierlich)

Schreibmodus: Max. 38mW

(für 166ns, Zyklusmin. 86,6ns)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 780-787 nm

Durée des impulsions et sortie maximum depuis

la lentille du bloc capteur optique

Mode de lecture: 0,7mW (continue)

Mode de gravure: max. 38mW

(pour 166ns, cycle min. 86,6ns)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 780-787 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora láser

Modo de lectura: 0,7mW (continua)

Modo de escritura: máx. 38mW

(para 166ns, ciclo mínimo 86,8ns)

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

English

OWNER’S MANUAL

SAFETY PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

These precautions explain how to use the device correctly and safely, thereby preventing injury to

yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION

section, according to the likelihood and nature of any potential injuries or damage inflicted. They

relate to your personal safety, and also help you minimize the risk of damaging the device. Please

read these sections carefully before proceeding.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions

include, but are not limited to, the following:

● Do not open the device or attempt to disassemble or modify it.

Otherwise, there is an increased risk of electrical shock or fire. The device contains no user-

serviceable parts. If it appears to be malfunctioning, have it inspected by qualified service

personnel.

● Do not look inside the device.

If you expose your eyes to the laser inside the device, you risk damage or loss of your vision.

● Do not insert fingers or foreign objects into the device.

Otherwise, there is an increased risk of personal injury, electrical shock, damage to the device or

fire. Please take particular care if small children are present.

● Do not expose the device to rain, use it near water or in damp or wet conditions or place containers

on it that contain liquids which might spill into any openings.

Otherwise, there is an increased risk of electrical shock, fire or personal injury.

● Follow the Owner’s Manual carefully.

Otherwise, there is an increased risk of personal injury, electrical shock, fire or damage to the unit.

Follow the correct procedure when setting up the device.

● If unusual smells, sounds or smoke emanate from the device or if liquids enter the device, switch

the computer off immediately and unplug it from the power outlet.

Otherwise, there is an increased risk of electrical shock, fire or damage to the device. Return the

device immediately to the store at which it was purchased or alternatively, to the nearest Yamaha

dealer (listed at the back of this manual).

● Make sure the computer is electrically grounded

Otherwise, there is an increased risk of electrical shock.

● When opening up the computer, always unplug the computer from the electrical outlet. Do not

touch the plug with wet hands.

Otherwise, there is an increased risk of electrical shock.

● When used in a fan-cooled system, the drive should not be exposed to temperatures outside the

range 5 ~ 35°C (41 ~ 95°F).

iii

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to

yourself or others, or damage to the instrument or other property. These precautions include, but

are not limited to, the following:

● Always unplug the computer from the electrical outlet if it will not be used for a prolonged period of

time or if there is a risk of lightning.

Otherwise, there is an increased risk of electrical shock, short-circuiting or fire.

● Do not expose the device to excessive heat or vibrations such as in direct sunlight or near a heater.

Also avoid placing it in extreme cold or much dust.

Otherwise, the front panel may become disfigured or the internal components may be damaged.

● Do not use the device near other electrical products such as televisions, radios or speakers.

Otherwise, this may cause interference which can affect the proper operation of those other

products.

● Do not place the device in an unstable position.

Otherwise, it may accidentally fall down and be damaged or cause personal injury.

● Mount the device horizontally.

Otherwise, written data may be destroyed. Set the device up according to the instructions in the

Owner’s Manual.

● Always remove the disc from the tray before transporting the device.

Otherwise, written data may be destroyed.

● When cleaning the device, never use benzene, paint thinners, detergents or chemical-impregnated

wiping cloths. Also, do not place vinyl, plastic or rubber objects on the device.

Otherwise, the device may be damaged or its front panel may become discolored. Use a soft, dry

cloth to wipe the device.

● Do not rest your weight on or place heavy objects on the device and do not use excessive force on

the buttons, switches or connectors.

Otherwise, there is an increased risk of damage to the device or personal injury.

● Do not listen to audio with headphones at high volume and for prolonged periods of time.

Otherwise, there is an increased risk of hearing loss.

● Before using the device, set the volume dial to its lowest setting.

Otherwise, sudden bursts of sound can cause hearing loss.

● Do not place the device near sources of magnetic interference, such as computer displays.

Magnetic interference can affect the operation and stability of the device.

● Have the device serviced regularly.

Otherwise, dust can build up inside the device, increasing the risk of fire or damage. For

information about servicing charges, contact the store at which the device was purchased or

alternatively, the nearest Yamaha dealer (listed at the back of this manual). The device should be

serviced about once a year.

■ About CD-R/RW discs

Please read the following regarding the handling of CD-R/RW discs.

1. Do not expose discs to excessive heat such as in direct sunlight or near a heater.

Also avoid keeping them in a humid place.

2. Do not touch disc surfaces.

When handling a disc, hold it by its edges.

3. Remove dust and dirt from disc surfaces.

Use air-based dust removers. The surfaces may be scratched if wiped with a dry cloth.

4. Do not stick labels on disc surfaces.

5. Do not write on disc surfaces except where indicated.

6. Do not clean discs with chemicals or detergents.

7. Do not bend or drop discs.

1. The information contained in this manual is subject to change

without prior notice.

2. All trademarks contained in this manual belong to their respective

owners.

3. Yamaha does not bear any responsibility for any outcome as a

result of using this device.

4. Reproduction of this manual, either in part or in full, is expressly

forbidden.

■ Precautions for Transportation

Before transporting the device, always put it in its original box. If the device is transported

without adequate packing, the internal components may be damaged and cause the device

to malfunction.

■ Copyrights

When writing to CD-R/RW, make sure that you are not infringing any copyrights. It is illegal

to copy audio CDs for non-personal use. When backing up software, please make sure that

you are not infringing any software copyrights for that product.

■ WARRANTY

YAMAHA AND SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA OR

ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS RECOMMENDED

THAT THE DISCS BE TESTED AFTER THEY HAVE BEEN WRITTEN TO.

FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND SUPPLIERS

GUARANTEE THE RELIABILITY OF THE DISCS.

Table of Contents

This document may not, in whole or in part, be copied, photocopied,

reproduced, translated, transmitted or reduced to any electronic medium of

machine readable form without prior consent in writing from Yamaha.

Windows is a registered trademark of Microsoft Corporation.

Macintosh is a registered trademark of Apple Computer, Inc.

All other trademarks are the property of their respective companies.

Introduction ....................................................................... 1

Features of the CRW2100SX Drive ................................................. 1

Before Use ......................................................................... 3

System Requirements ...................................................................... 3

Supported Discs .............................................................................. 5

Tools................................................................................................ 6

Front and Rear of Unit ........................................................... 7

Front Panel ..................................................................................... 7

Rear Panel ....................................................................................... 8

Setup Flowchart .................................................................. 9

Windows Users ............................................................................... 9

Macintosh Users ........................................................................... 10

Setup Procedures ............................................................... 11

Serial Number ............................................................................... 11

SCSI Settings ................................................................................. 11

Setting Up The CRW2100SX Drive .............................................. 14

Operation ......................................................................... 24

Loading a Disc .............................................................................. 24

Ejecting a Disc .............................................................................. 24

Ejecting a Disc in an Emergency................................................... 25

Troubleshooting ................................................................. 26

Appendix .......................................................................... 29

Writing Modes .............................................................................. 29

About the firmware ....................................................................... 31

LED Indicator Messages ................................................................ 32

CRW2100SX Specifications .......................................................... 33

Index ............................................................................................. 36

Introduction

Features of the CRW2100SX Drive

High speed

The CRW2100SX drive supports up to 16X speed writing of a CD-R disc, and up

to 10X speed writing of a CD-RW disc. For example, an audio CD (79 minutes/

700MB) can be created in approximately 5 minutes. With newly adopted Partial

CAV writing method (See the following column), you can write a disc by directly

transferring content data from a 32X-speed or faster CD-ROM drive. Data

reading at up to 40X speed is supported.

CD TEXT support

The CRW2100SX drive is compatible to CD TEXT format. Information such as

the song name or artist name can be recorded using writing software. The text

data on the disc you create can be displayed by a CD player that is compatible

with CD TEXT.

Wide compatibility

Compatibility assurance data obtained through exchange of technical data with

major disc manufacturers ensures compatibility with discs from a very wide range

of manufacturers. 700MB discs are also supported.

High-fidelity audio

The CRW2100SX supports extracting digital audio data at up to 40X speed, as

well as recording digital sound with complete fidelity even when writing at 16X

speed.

Reliable writing

Yamaha’s proprietary Pure-Phase Laser System

improves jitter values

to allow

the signal to be recorded accurately. In addition, the 8MB buffer memory and

Running OPC

technology further enhance reliability.

Optimum speed

The CRW2100SX drive can write at an optimum speed

if the CD-R disc does not

allow 12X- or 16X-speed writing.

Introduction

*1 Pure-Phase Laser System (patent applied for)

Technology that reduces phase interference of the laser beam, so that it shines accurately on the disc.

*2 Jitter value

An important measure of recording quality. This has been improved 25% compared with Yamaha models

not using this technology.

*3 Running OPC (Optimum Power Control)

CD-R/RW discs vary by manufacturer in their recording characteristics, and the laser output required

to write data differs by disc. Running OPC is technology that solves this problem by automatically

adjusting the output of the laser according to the material of the disc on which data is being written.

*4 If you attempt to write at 16X or 12X speed but the CRW2100SX drive detects that the quality of a

target CD-R disc and other things are inappropriate for such speeds, the drive will automatically slow

down the writing speed optimally for the disc.

About Partial CAV (Constant Angular Velocity)

Writing to a CD-R disc is normally done using CLV (Constant Linear

Velocity) method. In this method, the disc rotation speed will be so adjusted

as to keep a constant data transfer rate at any portion of the disc. In other

words, the disc rotation speed will vary in CLV writing.

In contrast, CAV (Constant Angular Velocity) method uses a constant disc

rotation speed at any portion of the disc whereas the data transfer rate will

vary. Because CAV method has an advantage to largely increase the data

transfer rate with a minimum load to the drive’s mechanism (compared to

CLV’s rotation speed adjustment), many of current CD-ROM drives use CAV

method.

CD formats define the constant linear density of written data (data should be

written onto the disc track in the constant pitch) so that amount of recorded

data per disc rotation will increase as the writing point moves from the inner

to the outer. In other words, in CAV writing the outer portion has an

increased data transfer rate.

The CRW2100SX drive uses CAV method in the inner portions as well as

CLV method in the outer portions (Partial CAV) in order to enable up to

16X-speed writing. The drive will control the disc rotation speed to start

writing at 12X speed in the inner portions, gradually accelerating up to 16X

speed and maintaining 16X speed in the outer portions.

Before Use

System Requirements

In order to use the CRW2100SX drive, your computer system will need to meet

the following set of requirements.

n The CRW2100SX drive may not write at a maximum speed depending on your

computer’s system configuration.

PC/AT-Compatible Computer

CPU: Pentium II-class or higher, 300MHz or faster.

RAM: 32MB memory (64MB or more recommended).

n If you are using Windows 2000 operating system, you need 64MB or more memory.

A spare PCI expansion slot for a SCSI card (if one hasn’t been installed yet).

A SCSI card to connect SCSI devices (including the CRW2100SX drive) to your

computer. Make sure it has an internal bus connector. Yamaha recommends any

of Adaptec’s AHA-2940-series cards (PCI slot).

n For details about how to install the SCSI card, refer to the documentation that came

with it.

Operating System (OS)

Windows 95, Windows 98, Windows 98 Second Edition, Windows NT4.0 with

Service Pack 3 or later, Windows 2000.

CD Writing Software

The CRW2100SX drive requires CD writing software to write onto a CD-R/RW

disc. When you use the CD writing software, make sure that it supports the

CRW2100SX drive.

n For details about how to install and use the software, refer to the documentation that

came with it.

Before Use

Hard Drive Space

When writing to a CD-R/RW disc, you will need a working area (50 to 100MB

free space) on the hard drive. When creating an image file for all data to write to

a CD-R/RW disc, in addition to the working area, you will need as much hard

drive space as that data (up to 900MB in total). However, such hard drive space

for the image file is not needed when you are directly writing from a hard drive,

CD-ROM drive or so on (on-the-fly writing).

n You can collect data files into a single disk image file for a CD-R/RW disc. That image

file can then be simply transferred and written onto a disc, avoiding writing errors

related to buffer underrun (a condition where writing is disabled due to under-

performance of the data transfer rate to the writing speed). Also, note that the image file

is useful to write multiple discs with the same content.

For Macintosh computers

OS: Mac OS 8 or later.

CPU: PowerPC G3, 300MHz or faster.

RAM: 32MB (64MB or more recommended).

CD-ROM drive.

n Many Apple Macintosh computers have built-in SCSI connectors. However, if your

Macintosh does not have a built-in SCSI connector, you will need to purchase a PCI

bus SCSI card. (Yamaha recommends Adaptec’s PowerDomain 2930U card.)

n For details about how to install the SCSI card, refer to the documentation that

came with it.

n When you use the CD writing software, make sure that it supports the

CRW2100SX drive.

Before Use

Supported Discs

The CRW2100SX drive can write to discs that carry the following logos.

CD-R discs

The CRW2100SX drive can write to these discs at 1X, 2X, 4X, 8X, 12X,

or 16X speed. These discs can be played back in a CD-ROM drive or a

CD player.

n 16X-speed writing is enabled with Partial CAV method. (P. 2)

n When writing at 8X or faster speeds, use “high-speed writing capable”

discs.

CD-RW discs

There are two types of CD-RW discs: those that support write/rewrite

speeds of 1X, 2X, and 4X, and those that support only 2X. The

CRW2100SX drive can write/rewrite at 2X or 4X speed on the first type

of disc and at 2X on the second type of disc. These discs can be read/

played on a device (e.g., CD-ROM drive) that supports “CD-RW.”

High Speed CD-RW discs

These discs allow writing/rewriting at 4X to 10X speeds. The

CRW2100SX drive can write/rewrite these discs at 4X, 8X, or 10X speed.

These discs can be read/played by a CD-RW drive that bears the High

Speed CD-RW logo, or by a device (e.g., CD-ROM drive) that supports

“CD-RW.”

n 10X-speed writing is enabled with Full CAV method.

• In order to write, erase, or read these discs using a CD-R/

RW drive, a drive bearing the High Speed CD-RW logo must

be used. When using a CD-ROM drive to read these discs,

the drive must be capable of reading CD-RW discs.

• If these discs are used in a CD-R/RW drive not bearing the

High Speed CD-RW logo, the discs may not be recognized,

resulting in the computer not operating correctly or other

malfunctions occurring.

• Refer to the page at the URL below before attempting to read

these discs on a Yamaha CD-R/RW drive not bearing the

High Speed CD-RW logo.

URL: http://www.yamaha.co.jp/english/product/computer/

*1 Compatible with Orange Book Part 2.

*2 Compatible with Orange Book Part 3 Vol. 1.

*3 Compatible with Orange Book Part 3 Vol. 2.

n The Orange Book standard defines how all recordable discs (including CD-R and CD-

RW) are written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to

CD-RW discs. The standard was named after the color of the book’s pages.

Before Use

About CD-ROM

A CD-ROM disc is a compact disc containing high-density read-only data. It

has many applications, including the playback of music and video, the

archiving of data, as well as on-line documentation. The following are

descriptions of each CD-ROM format:

CD-DA: Up to 79 minutes of stereo audio is written in 16-bit resolution at a

sampling rate of 44.1kHz for a 79 minutes disc.

Data CD: Up to 700 megabytes of computer data is stored in standard

ISO9660 format for a 700MB disc.

Video CD: These hold movies in which the video and audio data has been

compressed using MPEG-1 technology.

Tools

Phillips Screwdriver

You will need to use this when removing the cover of your computer and

installing a SCSI card.

n Make sure your screwdriver’s head is the correct size for the screws you need to remove.

Front and Rear of Unit

Front Panel

The CRW2100SX drive’s front panel features the following:

Manual Eject hole

Only use this if no other

method is available for

unloading a disc. (P. 25)

Disc tray

The tray is used to

hold the disc. It slides

out from the drive unit

when a disc needs to

be loaded or

unloaded. (P. 24)

Headphone jack

You can connect

stereo headphones

to this stereo mini

jack and listen to

audio CDs loaded

in the drive.

Headphone volume

control

Adjust this control to set a

suitable volume level when

listening to an audio CD

using the headphone jack.

Slide the knob to the left to

decrease the volume and to

the right to increase it.

Eject button

Press this button

when you need to

open or close the

tray. (P. 24)

Power switch

Press this button to

power up the drive

or to turn it off.

LED

Indicates the operation

status of the CRW2100SX

drive. (P. 32)

Front and Rear of Unit

Rear Panel

The CRW2100SX drive’s rear panel features the following:

SCSI

CDR ID

AC IN

SER. NO.

st2

❋❋❋❋❋❋❋❋

TERMINATOR

ONOFF

LINE OUT

SCSI

Serial number sticker

This consists of 3 letters

and 7 digits. You may

need to refer to this number

when requesting User

Support services. (P.11)

AC IN socket

Connect the included

power cable here. (P.20)

TERMINATOR switch

This enables the drive’s

built-in SCSI termination.

Switch this to “ON” if your

drive is the last device on

the SCSI chain. Otherwise,

switch it to “OFF.” (P.13)

LINE OUT (L/R)

To listen to audio CDs with

your drive, connect these to

the line-level input (LINE IN)

of your stereo equipment

using a standard stereo

phono cable (sold

separately).

CDR ID selector switch

The drive’s SCSI ID number

is shown in the switch’s

window. Press the button

above the window to

decrement the SCSI ID

number, or the button

below the window to

increment it. (P.12)

SCSI connectors

Connect either of these to

your computer’s SCSI card

using the SCSI cable. The

other connector can be

used as a pass-through

when daisy-chaining more

SCSI devices to it. It can

be left vacant if your drive

is the last device on the

SCSI chain and is

terminated. (P.20)

Setup Flowchart

These flowcharts show the procedure for setting up the CRW2100SX drive. For

easy cross-referencing, the relevant pages in this manual are also given.

Windows Users

STEP

Check that the SCSI card is

recognized correctly (P.22)

STEP

Check that the CRW2100SX

drive is recognized correctly

(P.22)

STEP

Do you have a SCSI card?

STEP

1-1

STEP

1-2

STEP

YES

Set up the CRW2100SX drive

Install the CD writing software

Purchase a SCSI card

Install the SCSI card

Recommended models:

Adaptec AHA-2940-series (PCI)

Read this manual and insert the

SCSI card into the appropriate

PCI slot on the computer.

For details about how to install the

software, refer to the documentation that

came with it.

Start using the CRW2100SX

drive!

Use the drive to create audio CDs, to

back up data on your hard disk, or for

whatever purpose suits your needs.

1. Set the switches at the rear of the drive.

(P.12, 13)

2. Connect the SCSI and power cables,

then switch the drive on. (P.18-20)

Setup Flowchart

Macintosh Users

STEP

1-1

STEP

1-2

STEP

YES

Set up the CRW2100SX drive

Check that the CRW2100SX

drive is recognized correctly

Purchase a SCSI card

Install the SCSI card

Recommended model:

Adaptec PowerDomain 2930U (PCI)

Read this manual and insert the

SCSI card into the appropriate

PCI slot on the computer.

Start using the CRW2100SX

drive!

Use the drive to create audio CDs, to

back up data on your hard disk, or for

whatever purpose suits your needs.

1. Set the switches at the rear of the drive.

(P.12, 13)

2. Connect the SCSI and power cables,

then switch the drive on. (P.18-20)

Use the Apple System Profiler and check

that the drive is recognized correctly.

Does your Macintosh have

a built-in SCSI connector?

For details about how to install the

software, refer to the documentation

that came with it.

Install the CD writing

software

Setup Procedures

Serial Number

Once you have taken the CRW2100SX drive out of its packaging, you should

immediately note down the serial number found at the rear of the drive under the

bar code. You may need to refer to this number when requesting Customer

Support services. In the box below the following diagram, write down the 10-

character serial number (consisting of 3 letters followed by 7 digits).

Serial number

(3 letters and 7 digits)

Serial No.

SCSI Settings

Before connecting your CRW2100SX drive to your computer, you need to set up

the drive using the switches located at the rear of the unit. You’ll need to set the

following:

● SCSI ID number

● Termination

Pagina se încarcă ...

Yamaha CRW-2100SX Manual de utilizare

Marca: Yamaha

Model: CRW-2100SX

Categorie: Unități de disc optice

Tip: Manual de utilizare

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha CRW-2100SX Kullanım kılavuzu
français: Yamaha CRW-2100SX Manuel utilisateur
English: Yamaha CRW-2100SX User manual
Deutsch: Yamaha CRW-2100SX Benutzerhandbuch
italiano: Yamaha CRW-2100SX Manuale utente
svenska: Yamaha CRW-2100SX Användarmanual
dansk: Yamaha CRW-2100SX Brugermanual
Nederlands: Yamaha CRW-2100SX Handleiding

Lucrări conexe

Alte documente

Dell PowerVault LTO3-060 Ghid de inițiere rapidă