Indesit iwb 5105 Manualul proprietarului

Categorie
Mașini de spălat
Tip
Manualul proprietarului

Acest manual este potrivit și pentru

GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
IWB 5105
Instructions for use
WASHING MACHINE
English,1
GB
Deutsch,13
DE
Slovensko,25
SL
Hrvatski,37
HR
Românã,49
RO
2
GB
Installation
This instruction manual should be kept in a safe
place for future reference. If the washing machine is
sold, transferred or moved, make sure that the
instruction manual remains with the machine so that
the new owner is able to familiarise himself/herself
with its operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 3
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washing machine
by screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Technical data
Model
IWB 5105
Dimensions
width 59.5 cm
height 85 cm
depth 52,5 cm
Capacity
from 1 to 5 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Spin speed
up to 1000 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme 2; temperature 60°C;
using a load of 5 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washing machine. If this is not the case, replace
the socket or the plug.
The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to rain,
storms and other weather conditions.
When the washing machine has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 2.
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
ON/OFF button: switches the washing machine on
and off.
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to
select the available functions. The indicator light
corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the
cold wash cycle (see Personalisation).
WASH CYCLE PROGRESS/DELAY TIMER
indicator light
s: used to monitor the progress of the
wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time
remaining until the wash cycle starts will be indicated
(see next page).
DOOR LOCKED indicator light: indicates whether
the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash
orange, while the indicator light for the current wash
cycle phase will remain lit in a fixed manner. If the
DOOR LOCKED
indicator light is switched off, the
door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
Standby mode
This washing machine, in compliance with new
energy saving regulations, is fitted with an automatic
standby system which is enabled after a few minutes
if no activity is detected. Press the ON-OFF button
briefly and wait for the machine to start up again.
Description of the washing machine
and starting a wash cycle
WASH CYCLE PROGRESS/
DELAY TIMER
indicator lights
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
GB
5
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see
Personalisation), after the wash cycle has been
started the indicator light corresponding to the
selected delay period will begin to flash:
As time passes, the remaining delay will be displayed
and the corresponding indicator light will flash:
The set programme will start once the selected time
delay has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to
indicate which phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding
indicator light will illuminate.
If the selected function is not compatible with the
programmed wash cycle, the corresponding indicator
light will flash and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the
indicator light corresponding to the first function
selected will flash and only the second function will be
activated; the indicator light corresponding to the
enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is
locked to prevent it from being opened; make sure
the indicator light is off before opening the door (wait
approximately 3 minutes). To open the door during a
running wash cycle, press the START/PAUSE button;
the door may be opened once the DOOR LOCKED
indicator light turns off.
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few
seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see Personalisation).
5. Measure out the detergent and washing additives (see Detergents and laundry).
6. Select the desired functions.
7. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit
in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
8. At the end of the wash cycle the
indicator light will switch on. The door can be opened once the DOOR
LOCKED
indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the
drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
6
GB
Specials wash cycles
Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes
and therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different
fabrics together (except for wool and silk items), with a maximum load of 1.5 kg.
Sport Intensive (
wash cycle
11) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We recommend
using a liquid detergent and dosage suitable for a half-load.
Sport Light (
wash cycle
12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We recommend
using a liquid detergent and dosage suitable for a half-load.
Sport Shoes (
wash cycle
13) is for washing sports shoes; for best results, do not wash more than 2 pairs
simultaneously.
Wash cycles
The information contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
Wash cycles
Table of wash cycles
Description of the wash cycle
Max
.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Cycle
duration
Prewash Wash
Fabric
softener
Normal
Eco
Time
Normal
Eco
Time
Daily
1
Cotton with prewash:
extremely soiled whites.
90° 1000
lll
5
-
171
-
2
Cotton:
extremely soiled whites.
90° 1000
-
ll
5
-
155
-
2
Cotton (1):
heavily soiled whites and resistant colours.
60° 1000
-
ll
5
-
133
-
2
Cotton (2):
heavily soiled whites and delicate colours.
40° 1000
-
ll
5
-
147
-
3
Cotton:
heavily soiled whites and resistant colours.
60° 1000
-
ll
53,25130104
4
Coloured Cottons (3):
lightly soiled whites and delicate colours.
40° 1000
-
ll
53,259271
5
Synthetics:
heavily soiled resistant colours.
60° 800
-
ll
2,5 2 85 72
6
Synthetics:
lightly soiled delicate colours.
40° 800
-
ll
2,5 2 70 60
Special
7
Wool:
for wool, cashmere, etc.
40° 600
-
ll
1
-
55
-
8
Silk/Curtains:
for garments in silk and viscose, lingerie.
30° 0
-
ll
1
-
55
-
9
Jeans
40° 800
-
ll
3
-
70
-
10
Express:
to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800
-
ll
1,5
-
15
-
Sport
11
Sport Intensive
30° 600
-
ll
3
-
78
-
12
Sport Light
30° 600
-
ll
3
-
68
-
13
Sport Shoes
30° 600
-
ll
Max. 2
pairs
-
50
-
Partial wash cycles
Rinse
-
1000
- -
l
5
-
36
-
Spin
-
1000
- - -
5
-
16
-
Drain
-
0
- - -
5
-
2
-
GB
7
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash
.
The washing machine will automatically prevent you from selecting a temperature which is higher than the
maximum value set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in
conjunction with the selected wash cycle.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of
lightly soiled cotton and synthetic fabrics (refer to the
"Table of wash cycles"
). enables you to wash in less
time thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load
quantity.
This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .
Extra rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin.
This function may not be used in conjunction with wash cycles 10, , .
1000-500
Press this button to reduce the spin speed.
This function may not be used in conjunction with wash cycles 8, .
Delay timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time
the button is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching
the set programme.
This option is enabled with all programmes.
Personalisation
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
ompartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites.
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 5 kg
Synthetic fabrics: max. 2,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 1 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using
programme 7, even those carrying the "hand-wash
only"
label. For best results, use special
detergents and do not exceed 1 kg of laundry.
1
2
3
Silk: use special wash cycle 8 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 8.
Jeans: Turn garments inside-out before washing and
use a liquid detergent. Use programme 9.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washing machine
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.
GB
9
Precautions and tips
This washing machine was designed and
constructed in accordance with international safety
regulations. The following information is provided for
safety reasons and must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
Do not open the detergent dispenser drawer while
the machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and
during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine
(see figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use second-hand hoses.
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),
make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light
for the first wash cycle stage
flashes rapidly).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The "Functions" indicator lights
and the "start/pause" indicator
light flash, while one of the
"phase in progress" indicator
lights and the "door locked"
indicator light will remain lit in a
fixed manner.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see Personalisation).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the
dwelling is on one of the upper floors of a building, there may be problems
relating to water drainage, causing the washing machine to fill with water
and drain continuously. Special anti-draining valves are available in shops
and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require
the drain phase to be started manually.
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see
Care and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the
text for washing machines or hand and machine wash, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also
be found on the front of the appliance by opening the door.
DE
13
Deutsch
INHALTSVERZEICHNIS
Installation 14-15
Auspacken und Aufstellen
Wasser- und Elektroanschlüsse
Erster Waschgang
Technische Daten
Beschreibung des Waschvollautomaten
und Starten eines Waschprogramms 16-17
Bedienblende
Kontrollleuchten
Starten eines Waschprogramms
Waschprogramme 18
Programmtabelle
Personalisierungen 19
Temperatureinstellung
Funktionen
Waschmittel und Wäsche 20
Waschmittelschublade
Vorsortieren der Wäsche
Besondere Wäscheteile
Unwuchtkontrollsystem
Vorsichtsmaßregeln und Hinweise 21
Allgemeine Sicherheit
Entsorgung
Reinigung und Pflege 22
Abstellen der Wasser- und Stromversorgung
Reinigung des Gerätes
Reinigung der Waschmittelschublade
Pflege der Gerätetür und Trommel
Reinigung der Pumpe
Kontrolle des Wasserzulaufschlauchs
Störungen und Abhilfe 23
Kundendienst 24
DE
IWB 5105
Bedienungsanleitungen
WASCHVOLLAUTOMAT
14
DE
Installation
Es ist äußerst wichtig, diese Bedienungsanleitung
sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen
zu können. Sorgen Sie dafür, dass sie im Falle eines
Umzugs oder einer Übergabe an einen anderen Benutzer
das Gerät stets begleitet, damit auch der neue Inhaber
die Möglichkeit hat, diese zu Rate zu ziehen.
Lesen Sie die Hinweise bitte aufmerksam durch, sie
liefern wichtige Informationen hinsichtlich der Installation,
des Gebrauchs und der Sicherheit.
Auspacken und Aufstellen
Auspacken
1. Gerät auspacken.
2. Sicherstellen, dass der Waschvollautomat keine
Transportschäden erlitten hat. Im Falle einer
Beschädigung Gerät bitte nicht anschließen, sondern
den Kundendienst anfordern.
3. Die 3 Transportschutz-
schrauben
herausschrauben und die
an der Geräterückwand
befindlichen Distanzstücke
aus Gummi entfernen
(siehe Abbildung).
4. Die Öffnungen mittels der mitgelieferten Abdeckungen
verschliessen.
5. Sämtliche Teile aufbewahren: Sollte der
Waschautomat erneut transportiert werden, müssen
diese Teile wieder eingesetzt werden.
Verpackungsmaterial ist kein Spielzeug für Kinder.
Nivellierung
1. Der Waschvollautomat muss auf einem ebenen,
festen, schwingungsfreien Untergrund aufgestellt werden
ohne diesen an Wände, Möbel etc. direkt anzulehnen.
2. Sollte der Boden nicht
perfekt eben sein, müssen
die Unebenheiten durch
An- bzw. Ausdrehen der
vorderen Stellfüße
ausgeglichen werden
(siehe Abbildung), der auf
der Arbeitsfläche zu
ermittelnde Neigungsgrad
darf nicht überschreiten.
Eine präzise Nivellierung verleiht dem Gerät die
erforderliche Stabilität, durch die Vibrationen,
Betriebsgeräusche und ein Verrücken des Gerätes
vermieden werden. Bei Teppichböden müssen die
Stellfüße so reguliert werden, dass ein ausreichender
Freiraum zur Belüftung unter dem Waschvollautomaten
gewährleistet ist.
Wasser- und Elektroanschlüsse
Anschluss des Zulaufschlauches
1. Schrauben Sie den
Wasserschlauch an einen
Kaltwasserhahn mit ¾-
GAS-Gewindeanschluss an
(siehe Abb.).
Lassen Sie das Wasser vor
dem Anschluss so lange
auslaufen, bis klares Wasser
austritt.
2. Das andere Ende des
Schlauches an den oben
rechts am Rückteil des
Waschvollautomaten
befindlichen
Wasseranschluss
anschließen (siehe
Abbildung).
3. Der Schlauch darf hierbei nicht eingeklemmt oder
abgeknickt werden.
Der Wasserdruck muss innerhalb der Werte liegen,
die in der Tabelle der technischen Daten angegeben
sind (siehe nebenstehende Seite).
Sollte der Zulaufschlauch nicht lang genug sein,
dann wenden Sie sich bitte an einen Fachhändler
oder an einen autorisierten Fachmann.
Verwenden Sie niemals bereits gebrauchte
Schläuche.
Verwenden Sie die Schläuche, die mit dem Gerät
geliefert wurden.
DE
15
Technische Daten
Modell
IWB 5105
Abmessungen
Breite 59,5 cm
Höhe 85 cm
Tiefe 52,5 cm
Fassungsvermögen
1 bis 5 kg
Elektroanschlüsse
siehe das am Gerät befindliche
Typens ch il d
Wasseranschlüsse
chstdruck 1 MPa (10 bar)
Mindestdruck 0,05 MPa (0,5 bar)
Trommelvolumen 46 Liter
Schleudertouren
bis zu 1000 U/min.
Prüfprogramme
gemäß EN 60456
Programm 2; Temperatur 60°C;
bei einer Lademenge von 5 kg.
Dieses Gerät entspricht den
folgenden EG-Richtlinien:
- 89/336/EWG vom 03.05.89
(elektromagnetische Verträglichkeit)
und nachfolgenden Änderungen
- 2002/96/CE
- 2006/95/CE (Niederspannung)
65 - 100 cm
Anschluss des Ablaufschlauches
Schließen Sie den
Ablaufschlauch ohne ihn
dabei abzuknicken an
einen geeigneten Abfluss
an. Die Mindestablaufhöhe
beträgt 65 - 100 cm
(gemessen vom Boden),
oder hängen Sie diesen
mittels des Schlauchhalters
gesichert in ein Becken
oder Wanne ein;
Befestigen Sie diesen
mittels des mitgelieferten
Schlauchhalters z.B. an
einen Wasserhahn (siehe
Abbildung). Das freie
Ablaufschlauchende darf
nicht unter Wasser
positioniert werden.
Verlängerungsschläuche sollten nicht eingesetzt
werden. Sollte dies unvermeidlich sein, muss die
Verlängerung denselben Durchmesser des
Originalschlauchs aufweisen und darf eine Länge von
150 cm nicht überschreiten.
Stromanschluss
Vor Einfügen des Netzsteckers in die Steckdose ist
sicherzustellen, dass:
die Steckdose über eine normgerechte Erdung verfügt;
die Steckdose die in den Technischen Daten
angegebenen Höchstlast des Gerätes trägt (siehe
nebenstehende Tabelle);
die Stromspannung den in den Technischen Daten
angegebenen Werten entspricht (siehe
nebenstehende Tabelle);
die Steckdose mit dem Netzstecker des
Waschvollautomaten kompatibel ist. Andernfalls
muss der Netzstecker (oder die Steckdose) ersetzt
werden.
Der Waschvollautomat darf nicht im Freien installiert
werden, auch nicht, wenn es sich um einen
geschützten Platz handelt. Es ist gefährlich, das
Gerät Gewittern und Unwettern auszusetzen.
Die Steckdose sollte nach installiertem Gerät leicht
zugänglich sein.
Verwenden Sie bitte keine Verlängerungen oder
Mehrfachstecker.
Das Netzkabel darf nicht gebogen bzw.
eingeklemmt werden.
Das Versorgungskabel darf nur durch autorisierte
Fachkräfte ausgetauscht werden.
Achtung! Der Hersteller übernimmt keinerlei Haftung,
sollten diese Vorschriften nicht genau beachtet
werden.
Erster Waschgang
Lassen Sie nach der Installation bzw. vor erstmaligem
Gebrauch erst einen Waschgang (mit Waschmittel)
ohne Wäsche durchlaufen. Stellen Sie hierzu das
Waschprogramm 2 ein.
16
DE
Waschmittelschublade: für Waschmittel und
Zusätze (siehe Waschmittel und Wäsche).
Taste EIN/AUS: Zum Ein- und Ausschalten Ihres
Waschvollautomaten.
Wählschalter PROGRAMME: Zur Wahl der
Waschprogramme. Während des Programmablaufs
bleibt der Schalter feststehend.
Tasten mit Kontrollleuchten FUNKTIONEN: Zur
Einstellung der verfügbaren Funktionen. Die der
gewählten Einstellung entsprechende Kontrollleuchte
bleibt eingeschaltet.
Wählschalter TEMPERATUREN: Zur Einstellung der
Waschtemperatur oder einer Kaltwäsche (siehe
Personalisierungen).
Kontrollleuchten PROGRAMMABLAUF/
STARTZEITVORWAHL: Zur Kontrolle des
Waschprogrammablaufs.
Die eingeschaltete Kontrollleuchte zeigt die laufende
Programmphase an.
Wurde die Funktion Startzeitvorwahl eingestellt,
zeigen sie die bis zum Start noch verbleibende Zeit an
(siehe Nebenseite).
Kontrollleuchte GERÄTETÜR GESPERRT: Diese
Taste zeigt an, ob die Gerätetür geöffnet werden
kann oder nicht (siehe Nebenseite).
Taste mit Kontrollleuchte START/PAUSE: Mittels
dieser Taste werden die Waschprogramme gestartet
oder kurz unterbrochen.
NB: Durch Drücken dieser Taste, kann das
Waschprogramm zeitweilig unterbrochen werden
(Pause). Die entsprechende Kontrollleuchte schaltet
auf orangefarbenes Blinklicht, die Kontrollleuchte der
bestehenden Programmphase dagegen schaltet auf
Dauerlicht. Sobald die Kontrollleuchte GERÄTETÜR
GESPERRT
erlischt, kann die Gerätetür geöffnet
werden.
Um das Programm an der Stelle, an der es
unterbrochen wurde, wieder in Gang zu setzen,
drücken Sie diese Taste erneut.
Funktion Standby
Zur Erfüllung der neuen Richtlinien zum
Energieverbrauch ist diese Waschmaschine mit einem
automatischen Ausschaltsystem (Standby)
ausgestattet, das nach einigen Minuten des
Nichtgebrauchs in Funktion tritt. Drücken Sie kurz die
Taste EIN/AUS und warten Sie, bis sich die Maschine
wieder einschaltet.
Beschreibung des Waschvollautomaten
und Starten eines Waschprogramms
Kontrollleuchten
PROGRAMMABLAUF/
STARTZEITVORWAHL
Kontrollleuchte
GERÄTETÜR
GESPERRT
Taste mit
Kontrollleuchte
START/
PAUSE
Bedienblende
Waschmittelschublade
Taste
EIN/AUS
Wählschalter
PROGRAMME
Tasten mit
Kontrollleuchten
FUNKTIONEN
Wählschalter
TEMPERATUREN
DE
17
Kontrollleuchten
Die Kontrollleuchten liefern wichtige Hinweise.
Sie signalisieren:
Startzeitvorwahl
Wurde die Funktion Startzeitvorwahl (siehe
Personalisierungen) aktiviert, und das Programm in
Gang gesetzt, schaltet die Kontrollleuchte, die der
eingestellten Zeitverschiebung entspricht, auf Blinklicht:
Nach und nach wird die bis zum effektiven Start noch
verbleibende Zeit eingeblendet, die entsprechende
Kontrollleuchte blinkt:
Nach Ablauf der eingestellten Verzögerungszeit startet
das ausgewählte Programm.
Laufende Programmphase
Wurde das Waschprogramm gewählt und gestartet,
leuchten die Kontrollleuchten nach und nach auf, und
zeigen so den jeweiligen Programmstand an.
Funktionstasten und entsprechende
Kontrollleuchten
Nach der Wahl einer Funktion leuchtet die
entsprechendeTaste auf. Ist die gewählte Funktion nicht
vereinbar mit dem eingestellten Programm, schaltet die
entsprechende Kontrollleuchte auf Blinklicht und die
Funktion wird nicht aktiviert. Ist die gewählte Funktion
mit einer anderen bereits eingestellten nicht
kompatibel, schaltet die der ersten Funktion
entsprechende Kontrollleuchte auf Blinklicht und nur
die zweite Funktion wird aktiviert, die Kontrollleuchte
der aktivierten Funktion schaltet auf Dauerlicht.
Kontrollleuchte Gerätetür gesperrt:
Ist diese Kontrollleuchte eingeschaltet, bedeutet dies,
dass das Bullauge gesperrt ist; warten Sie, bis die
Leuchte erlischt, um das Bullauge zu öffnen (etwa 3
Minuten). Um während eines laufenden Programms das
Bullauge zu öffnen, drücken Sie die Taste START/
PAUSE; ist die der GERÄTETÜR GESPERRT
entsprechende Kontrollleuchte ausgeschaltet, kann das
Bullauge geöffnet werden.
Starten eines Waschprogramms
1. Schalten Sie den Waschvollautomaten durch Drücken der EIN/AUS-Taste ein. Sämtliche Kontrollleuchten leuchten
für einige Sekunden auf, und erlöschen wieder. Die Kontrollleuchte START/PAUSE schaltet auf Blinklicht.
2. Füllen Sie die Wäsche ein, und schließen Sie die Gerätetür.
3. Stellen Sie mittels des Wählschalters PROGRAMME das gewünschte Programm ein.
4. Stellen Sie die Waschtemperatur ein (siehe Personalisierungen).
5. Füllen Sie Waschmittel und Zusätze ein (siehe Waschmittel und Wäsche).
6. Wählen Sie die gewünschten Funktionen.
7. Setzen Sie das Programm in Gang. Drücken Sie hierzu die Taste START/PAUSE. Die entsprechende Kontrollleuchte
bleibt eingeschaltet (grünes Dauerlicht). Um die Waschprogramm-Einstellung rückgängig zu machen, muss das Gerät
auf Pause geschaltet werden. Drücken Sie hierzu die Taste START/PAUSE. Wählen Sie daraufhin das neue Programm.
8. Nach Ablauf des Waschprogramms leuchtet die Kontrollleuchte
auf. Sobald die Kontrollleuchte GERÄTETÜR
GESPERRT
erlischt, kann das Bullauge geöffnet werden. Nehmen Sie die Wäsche aus der Maschine und lassen Sie
die Gerätetür leicht offen stehen, damit die Trommel trocknen kann. Schalten Sie den Waschvollautomaten durch
Drücken der EIN/AUS-Taste aus.
Hauptwäsche
Spülen
Schleudern
Wasserablauf
Ende des Waschgangs
18
DE
Beschreibung des Programms
Max.
Te m p e r a t u r
(°C)
Max.
Schleuder-
Geschwin-
digkeit
(U/min)
Waschmittel
Max.
Beladungs-
menge (kg)
Programmd-
auer
Vor-
wäsche
Haupt-
wäsche
Weich-
spüler
Normal
Eco
Time
Normal
Eco
Time
Programme für die tägliche sche (Daily)
1
Baumwolle + Vorwasche:
stark verschmutzte Kochwäsche.
90° 1000
lll
5
-
171
-
2
Baumwolle:
stark verschmutzte Kochwäsche.
90° 1000
-
ll
5
-
155
-
2
Baumwolle (1):
stark verschmutzte Weiß- und farbechte Buntwäsche.
60° 1000
-
ll
5
-
133
-
2
Baumwolle (2):
stark verschmutzte Weiß- und empfindliche
Buntsche.
40° 1000
-
ll
5
-
147
-
3
Baumwolle:
stark verschmutzte Weiß- und farbechte Buntwäsche.
60° 1000
-
ll
53,25130104
4
Baumwolle-Buntwäsche (3)
:
leicht verschmutzte
Weißwäsche und empfindliche Buntsche.
40° 1000
-
ll
53,2592 71
5
Synthetik
:
stark verschmutzte, farbechte Buntwäsche.
60° 800
-
ll
2,5 2 85 72
6
Synthetik
:
leicht verschmutzte, farbechte Buntwäsche.
40° 800
-
ll
2,5 2 70 60
Spezialprogramme (Special)
7
Wolle:
wolle, Kaschmir usw.
40° 600
-
ll
1
-
55
-
8
Seide/Gardinen:
kleidungsscke aus Seide, Viskose und Feinwäsche.
30° 0
-
ll
1
-
55
-
9
Jeans
40° 800
-
ll
3
-
70
-
10
Express:
zum kurzen Auffrischen leicht verschmutzter
Wäsche (nicht geeignet für Wolle, Seide und Handsche).
30° 800
-
ll
1,5
-
15
-
Sport
11
Sport Intensive
30° 600
-
ll
3
-
78
-
12
Sport Light
30° 600
-
ll
3
-
68
-
13
Sport Shoes
30° 600
-
ll
M
ax
. 2
Paar
-
50
-
Teilprogramme
Spülen
-
1000
- -
l
5
-
36
-
Schleudern
-
1000
- - -
5
-
16
-
Abpumpen
-
0
- - -
5
-
2
-
Sonderprogramme
Express (Programm 10) Kurzprogramm für die Wäsche leicht verschmutzter Teile: in nur 15 Minuten, zur Einsparung
von Zeit und Energie. Stellen Sie dieses Waschprogramm (10 bei 30°C) ein, dann können, bei einer maximalen
Lademenge von 1,5 kg, Gewebe unterschiedlicher Art (mit Ausnahme von Wolle und Seide) zusammen gewaschen
werden.
Sport Intensive (Programm 11) ist speziell für stark verschmutzte Sportkleidung (Trainingsanzüge, Sporthosen; für
beste Resultate empfehlen wir, die in der "Programmtabelle" angezeigte maximale Füllmenge nicht zu übersteigen.
Sport Light (Programm 12) ist speziell für wenig verschmutzte Sportkleidung (Trainingsanzüge, Sporthosen; für beste
Resultate empfehlen wir, die in der "Programmtabelle" angezeigte maximale Füllmenge nicht zu übersteigen. Verwenden
Sie ein Flüssigwaschmittel und nur die Menge für eine halbe Gerätefüllung.
Sport Shoes (Programm 13) ist speziell für das Waschen von Sportschuhen; für beste Resultate waschen Sie
nicht mehr als 2 Paar.
Waschprogramme
Bei den in der Tabelle angegebenen Daten handelt es sich um Richtwerte.
Für alle Testinstitute:
1) Prüfprogramm gemäß EN 60456: Programm 2 und eine Temperatur von 60°C einstellen.
2) Langes Baumwollprogramm: Programm 2 und eine Temperatur von 40°C einstellen.
3) Kurzes Baumwollprogramm: Programm 4 und eine Temperatur von 40°C einstellen.
Waschprogramme
Programmtabelle
DE
19
Temperatureinstellung
Drehen Sie den Wählschalter TEMPERATUREN, um die Waschtemperatur einzustellen (siehe Programmtabelle).
Die Temperatur kann bis auf Kaltwäsche
herabgesetzt werden.
Der Waschvollautomat verhindert automatisch die Einstellung einer höheren Schleuderstufe, sollte diese die für das
jeweilige Programm vorgeschriebene Höchstgeschwindigkeit übersteigen.
Funktionen
Die verschiedenen Waschfunktionen, die Ihnen Ihr Waschvollautomat bietet, ermöglichen es Ihnen, hygienisch
saubere und weiße Wäsche zu erhalten, die Ihren Wünschen entspricht.
Aktivierung der Funktionen:
1. Drücken Sie die Taste, die der gewünschten Funktion entspricht.
2. Das Aufleuchten der entsprechenden Kontrollleuchte zeigt an, dass die Funktion aktiviert wurde.
Anmerkung: Sollte die Kontrollleuchte jedoch auf rasches Blinklicht schalten, dann bedeutet dies, dass die Funktion zu
dem eingestellten Programm nicht zugeschaltet werden kann.
Durch Auswahl dieser Option werden die mechanische Bewegung, die Temperatur und das Wasser für eine verminderte
Füllmenge mit wenig verschmutzten Baumwoll- und Synthetikstoffen optimiert (siehe "Programmtabelle").
Mit
werden die Waschzeiten verkürzt, was Wasser und Energie spart. Wir empfehlen, die für die Füllmenge
geeignete Menge Flüssigwaschmittel zu verwenden.
Diese Funktion kann zu den Programmen 1, 2, 7, 8, 9, 10, 11, 12, 13, , , nicht zugeschaltet werden.
Extraspülgang
Wählen Sie diese Zusatzfunktion, wird die Spülwirkung erhöht und somit ein optimales Ausspülen des Waschmittels
garantiert. Dies ist besonders angezeigt bei sehr empfindlicher Haut bzw. Waschmittelallergien.
Diese Funktion kann zu den Programmen 10, , nicht zugeschaltet werden.
1000-500
Mit dieser Taste wird die Schleudergeschwindigkeit reduziert.
Diese Funktion kann zu den Programmen 8, nicht zugeschaltet werden.
Startzeitvorwahl
Der Start des Waschprogramms kann bis zu 12 Stunden verschoben werden.
Drücken Sie die Taste mehrmals, bis die der gewünschten Zeitverschiebung entsprechende Kontrollleuchte aufleuchtet.
Ein fünfter Tastendruck deaktiviert die Funktion.
NB: Ist die Taste START/PAUSE einmal gedrückt, kann der gewählte Zeitverschiebungswert nur noch herabgesetzt werden
bis zum Start des eingestellten Programms.
Obiges gilt für alle Programme.
Personalisierungen
20
DE
Waschmittel und Wäsche
Waschmittel und Wäsche
Ein gutes Waschergebnis hängt auch von einer
korrekten Waschmitteldosierung ab: Eine zu hohe
Dosierung bedeutet nicht unbedingt reinere Wäsche,
sie trägt nur dazu bei, die Maschineninnenteile zu
verkrusten und die Umwelt zu belasten.
Verwenden Sie keine Handwaschmittel, sie
verursachen eine zu hohe Schaumbildung.
Schublade herausziehen
und Waschmittel oder
Zusätze wie folgt
einfüllen:
In Kammer 1: Waschpulver für die Vorwäsche
(Waschpulver)
In Kammer 2: Waschmittel für die
Hauptwäsche (Waschpulver oder
Flüssigwaschmittel)
Flüssigwaschmittel nur kurz vor dem Start einfüllen.
In Kammer 3: Zusätze (Weichspüler usw.)
Der Weichspüler darf das Gitter nicht übersteigen.
Vorsortieren der Wäsche
Sortieren Sie die Wäsche nach:
- Gewebeart / Waschetikettensymbol.
- und Farben: Buntwäsche von Weißwäsche
trennen.
Entleeren Sie alle Taschen.
Das angegebene Gewicht, das sich auf die
maximale Ladung an Trockenwäsche bezieht, sollte
nicht überschritten werden:
Widerstandsfähige Gewebe: max 5 kg
Kunstfasergewebe: max 2,5 kg
Feinwäsche: max 2 kg
Wolle: max 1 kg
Seide: max 1 kg
Wie schwer ist Wäsche?
1 Betttuch 400-500 gr
1 Kissenbezug 150-200 gr
1 Tischdecke 400-500 gr
1 Bademantel 900-1.200 gr
1 Handtuch 150-250 gr
1
2
3
Besondere Wäscheteile
Wolle: Mit dem Programm 7 können alle Wollsachen
gewaschen werden, auch wenn das Etikett "nur
Handwäsche"
zeigt. Für beste Ergebnisse
verwenden Sie ein spezifisches Waschmittel und
waschen Sie maximal 1 kg Wäsche.
Seide: Wählen Sie das Spezialprogramm 8 zum
Waschen aller Kleidungs- bzw. Wäschestücke aus
Seide. Es empfiehlt sich der Einsatz von
Feinwaschmittel.
Gardinen: Sie sollten zusammengelegt und in den
mitgelieferten Beutel gesteckt werden. Stellen Sie das
Programma 8 ein.
Jeans: drehen Sie die Wäschestücke vor der
Wäsche auf links und verwenden Sie ein
Flüssigwaschmittel. Stellen Sie das Programm 9 ein.
Unwuchtkontrollsystem
Um starke Vibrationen oder eine Unwucht beim
Schleudern zu vermeiden, verfügt das Gerät über ein
Schleuderunwuchtsystem. Die Waschladung wird
durch eine erhöhte Rotation der Trommel als die des
WAschgangs ausbalanciert. Sollte die Wäscheladung
nach Ablauf mehrerer Versuche immer noch nicht
korrekt verteilt sein, schleudert das Gerät die Wäsche
bei einer niedrigeren Geschwindigkeit als die der
vorgesehenen Schleudergeschwindigkeit. Sollte die
Wäsche extrem ungleichmäßig verteilt sein, führt das
Gerät anstelle des Schleudergangs einen
Wäscheverteilungs-Zyklus durch. Um eine optimale
Verteilung der Wäscheladung und somit eine korrekte
Auswuchtung zu fördern, sollten große und kleine
Wäscheteile gemischt eingefüllt werden.
1 / 1

Indesit iwb 5105 Manualul proprietarului

Categorie
Mașini de spălat
Tip
Manualul proprietarului
Acest manual este potrivit și pentru