Yamaha RX-A3010 Manualul proprietarului

RX-A3010
Yamaha
Marca
Yamaha
Model
RX-A3010
Categorie
Receptoare AV
Tip
Manualul proprietarului
Check that the following accessories are supplied with this product.
You need to separately prepare the following cables to build the system based on this
document.
■ Speaker cables (x 9)
■ HDMI cable (x 2)
■ Audio pin cable (x 1)
■ Digital optical cable or stereo pin cable (x 1) (unnecessary if your TV supports ARC)
1 Preparations
Accessories
■ Remote control ■ Batteries (AAA, LR03, UM-4) (x 4)
Insert into the remote control in the correct polarity (+/-)
■ Simplified remote control ■ Power cable
* The figure of the supplied power cable differs depending
on regions.
■ YPAO microphone ■ Microphone base
* Used for angle
measurement
during YPAO.
■ AM antenna ■ FM antenna
* The figure of the supplied
FM antenna differs
depending on regions.
■
CD-ROM
(Owner’s Manual)
■ Safety Brochure ■ Easy Setup Guide
(this document)
Cables necessary for connections
Easy Setup Guide
English for Canada, Europe, Asia,
Africa, Oceania and Latin America
AV Receiver
This document explains how to set up a 9.1-channel system and
play back surround sound of a BD/DVD on this unit.
For more information, refer to “Owner’s Manual” on the supplied
CD-ROM.
A PDF format of this guide and “Owner’s Manual” can be downloaded
from the following website.
http://download.yamaha.com/
2 En
Set up the speakers in the room by using the following diagram as a reference.
For information on speaker systems other than the 9.1-channel system, refer to “Owner’s Manual”.
2 Placing the speakers
30 cm or more
1.8 m
0.5 to 1 m
1.8 m
0.5 to 1 m
10°~30°10°~30°
Front speaker (L)
Front speaker (R)
Center speaker
Surround speaker (L)
Surround speaker (R)
Surround back speaker (L)
Surround back speaker (R)
Front presence speaker (L)
Front presence speaker (R)
Subwoofer
En 3
Connecting speaker cables
Speaker cables have two wires. One is for connecting
the negative (-) terminal of the unit and the speaker, and
the other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire to
the negative and the other wire to the positive.
a
Remove approximately
10 mm of insulation from
the ends of the speaker
cable, and twist the bare
wires of the cable
together firmly.
b Loosen the speaker
terminal.
c Insert the bare wires of the cable into the gap on the
side (upper right or bottom left) of the terminal.
d Tighten the terminal.
Using a banana plug
(Canada, China, Australia and General models only)
a Tighten the speaker
terminal.
b Insert a banana plug into
the end of the terminal.
1
Connect the front speakers ( / )
to the FRONT ( / ) and the center
speaker ( ) to the CENTER terminal.
2
Connect the surround speakers ( /
) to the SURROUND ( / )
terminals.
3 Connecting the speakers/subwoofer
• This unit is configured for 8-ohm speakers at the factory. When
connecting 6-ohm speakers, set the speaker impedance of this
unit to “6 Ω MIN”. For details, see “Setting the speaker
impedance” (p.18) in “Owner’s Manual”.
• Use a subwoofer equipped with built-in amplifier.
• Remove the power cable of this unit from an AC wall outlet and
turn off the subwoofer before connecting the speakers.
• Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker
cables short circuit, “CHECK SP WIRES” will appear on the
front display when this unit is turned on.
FRONT
-
+
aa
b
b
c
c
d
d
– (black)
+ (red)
FRONT
+
aa
b
b
Banana plug
SPEAKER IMPEDANCE
1
2
AUDIO 4
MULTI CH INPUT
ZONE OUT/PRE OUT
AUDIO 3
CENTER
SUBWOOFER
ZONE 2/
F.PRESENCE
ZONE 3/
R.PRESENCE
FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R L
SURROUND
R L
R
R
R
L
L
L
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
EXTRA SP1EXTRA SP2
SINGLE
This unit (rear)
SPEAKER IMPEDANCE
1
2
AUDIO 4
MULTI CH INPUT
ZONE OUT/PRE OUT
AUDIO 3
CENTER
SUBWOOFER
ZONE 2/
F.PRESENCE
ZONE 3/
R.PRESENCE
FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R L
SURROUND
R L
R
R
R
L
L
L
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
EXTRA SP1EXTRA SP2
SINGLE
This unit (rear)
4 En
3
Connect the surround back speakers
( / ) to the SURROUND BACK
( / ) terminals.
4
Connect the front presence speakers
( / ) to the EXTRA SP1 ( / )
terminals.
5
Connect the subwoofer ( ) to the
SUBWOOFER (1) jack.
SPEAKER IMPEDANCE
1
2
AUDIO 4
MULTI CH INPUT
ZONE OUT/PRE OUT
AUDIO 3
CENTER
SUBWOOFER
ZONE 2/
F.PRESENCE
ZONE 3/
R.PRESENCE
FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R L
SURROUND
R L
R
R
R
L
L
L
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
EXTRA SP1EXTRA SP2
SINGLE
This unit (rear)
SPEAKER IMPEDANCE
1
2
AUDIO 4
MULTI CH INPUT
ZONE OUT/PRE OUT
AUDIO 3
CENTER
SUBWOOFER
ZONE 2/
F.PRESENCE
ZONE 3/
R.PRESENCE
FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R L
SURROUND
R L
R
R
R
L
L
L
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
EXTRA SP1EXTRA SP2
SINGLE
This unit (rear)
SPEAKER IMPEDANCE
1
2
AUDIO 4
MULTI CH INPUT
ZONE OUT/PRE OUT
AUDIO 3
CENTER
SUBWOOFER
ZONE 2/
F.PRESENCE
ZONE 3/
R.PRESENCE
FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R L
SURROUND
R L
R
R
R
L
L
L
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
EXTRA SP1EXTRA SP2
SINGLE
This unit (rear)
Use an audio pin cable to
connect the subwoofer
().
(
SINGLE
)
PRE OUT
CENTER
CENTER
SUR. BACKSURRUND
1
2
FRONT
(
REAR
)
SUBWOOFER
(
FRONT
)
Audio pin
cable
En 5
4 Connecting the external devices
SCENE
MULTI ZONE
HDMI IN
VIDEO AUX
TONE/BALANCEOPTIONON SCREEN
DISPLAYRETURN
STRAIGHT
1
ENTER
ZONE 2 ZONE 3 ZONE 4
2 3 4
ZONE CONTROL
INFO MEMORY
YPAO MIC
PHONES
SILENT CINEMA
USB
iPod/iPhone
PROGRAM TUNING/CH
PRESET
R OPTICALL AUDIOVIDEOS VIDEO
PURE DIRECT
VOLUMEINPUT
MAIN ZONE
NATURAL SOUND AV RECEIVER RX-A3010
FM AM
RS-232C
SPEAKER IMPEDANCE
FM
75Ω
ANTENNA
AM
(4 RADIO)
AV 1
(1 BD/DVD)
COAXIAL
1
+12V 0.1A MAX.
AC IN
TRIGGER
OUT
DOCK
YP
B PR
YPB PR
YPB PR
OPTICAL
AV OUT
AV OU T/
ZONE 4
R
L
HDMI OUT
ARC
1
1
1
2
2
HDMI
(1 BD/DVD)
MONITOR OUT/
ZONE OUT
MONITOR OUT/ZONE OUT
IN OUT
2
IN OUT
AV 1
AV 1
AV 3
AV 2 AV 3 AV 4 AV 5 AV 6 AV 7
1
2
REMOTE
COMPONENT VIDEO
AV 3 AV 4AV 2
AUDIO 4
MULTI CH INPUT
ZONE OUT/PRE OUT
AUDIO 3AUDIO 2
(3 CD)
AUDIO 1
(2 TV)
CENTER
SUBWOOFER
ZONE 2/
F.PRESENCE
ZONE 3/
R.PRESENCE
FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R
5
OPTICAL
4
OPTICAL
3
COAXIAL
2
COAXIAL
6
L
SURROUND
R L
R
R
R
L
L
L
PHONO
NETWORK
A
AV 2
B
C
AV 4
D
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
GND
EXTRA SP1
EXTRA SP2
SINGLE
(1 BD/DVD)
AV 1
HDMI OUT
ARC
12
HDMI
HDMI
HDMI
HDMI
HDMI
a
d
c
HDMI
b
OPTICAL
AUDIO 1
(2 TV)
5
OPTICAL
L
R
L
R
L
R
O
O
VOLTAGE SELECTOR
220V-
240V
110V-
120V
Audio out (digital optical or
analog stereo)
TV
HDMI in
HDMI out
BD/DVD player
HDMI (AV1) jack
HDMI OUT 1
jack
AUDIO1
(OPTICAL or AUDIO)
jack
Turn on this unit
This unit (rear)
This unit (front)
To an AC
wall outlet
VOLTAGE SELECTOR
(General model only)
1
Connect the external devices to this unit.
a Connect the BD/DVD player and this unit with an
HDMI cable.
If the BD/DVD player is currently connected to the
TV directly with an HDMI cable, disconnect the
cable from the TV and connect it to this unit.
b Connect the TV and this unit with another HDMI
cable.
c Connect the TV and this unit with a digital optical
cable or a stereo pin cable.
This connection is required to play back TV audio
on this unit. If your TV supports ARC (Audio Return
Channel), this connection is unnecessary.
d Connect the supplied power cable to this unit and
then to an AC wall outlet.
• For information on how to connect radio antennas or other
external devices, see “SETUP” in “Owner’s Manual”.
2
Turn on this unit, TV and BD/DVD player.
3
With the remote control of the TV, switch the
TV input to display the video from this unit.
The connections are complete. Move to the next
page to optimize the speaker settings.
Before connecting the power cable (General model only)
Make sure you set the switch position of VOLTAGE
SELECTOR according to your local voltage. Voltages are AC
110-120/220-240 V, 50/60 Hz.
Opening the front panel door
Press the bottom of the door gently.
6 En
By using the Yamaha Parametric room Acoustic Optimizer (YPAO) function, this unit automatically detects speaker
connections and distances from the listening position, and optimizes the speaker settings such as volume balance and
acoustic parameters to suit your room.
Preparing for YPAO
5
Optimizing the speaker settings automatically (YPAO)
• During the measuring process, the test tones are output at high volume. Take care
that the test tone does not frighten small children. Also, refrain from using this
function at night when it may be a nuisance to others.
• During the measuring process, you cannot adjust the volume.
• During the measuring process, keep the room as quiet as possible.
• Do not connect headphones.
• If your subwoofer supports the auto-standby function, disable it.
• YPAO measurement is not performed correctly when any obstacles are in the room.
• During the measuring process (about 3 minutes), keep stuff in the corners or
remove it from the room.
1
Connect the YPAO microphone to the
YPAO MIC jack on the front panel.
The following screen appears on the TV.
• To cancel the operation, disconnect the YPAO microphone
before starting the measurement.
2
To start the measurement, use the cursor
keys to select “Measure” and press
ENTER.
The measurement will start in 10 seconds.
The following screen appears on the TV when
the measurement finishes.
• If any error message (such as E-1) or warning message (such
as W-2) appears, see “Error messages” (p.55) or “Warning
messages” (p.56) in “Owner’s Manual”.
• If the warning message “W-1:Out of Phase” appears, see “If
‘W-1:Out of Phase’ appears” (next page).
VOLUME HIGH CUT
CROSSOVER/
MIN MAXMIN MAX
[ B ][ A ]
SOURCE
RECEIVER
AV
AUDIO
1 2 3 4
5 6 7
V-A UX
1 2 3 4
MULTI
PHONO
USB NET
TUNER
DOCK
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO STRAIGHT
INPUT
PURE
DIRECT
MUTE
TV
SCENE
1 2 3 4
PROGRAM
VOLUME
TV VOL
MUTE
MODE
TOP MENU
RETURN DISPLAY
POP-UP/MENU
TV CH
PRESET
ENTER
ON SCREEN
OPTION
[ B ]
[
A
]
SOU
R
CE
RECEIV
E
AV
AU
DI
O
1
2
3
4
5
6
7
V
-
AU
X
1
2
3
4
MU
LT
I
P
HO
N
O
US
B
NE
T
TUNER
DOC
K
This unit (front)
Place the YPAO microphone at ear
height in your listening position. We
recommend using a tripod to adjust the
height. You can use the tripod screws to
fix the microphone in place.
YPAO microphone
Listening position
Ear height
Cursor keys
ENTER
RETURN
Turned on the subwoofer and set
the volume to half. If the
cross-over frequency is
adjustable, set it to maximum.
Turned on the subwoofer and set
the volume to half. If the
cross-over frequency is
adjustable, set it to maximum.
En 7
3
Use the cursor keys to select
“Save/Cancel” and press ENTER.
4
Use the cursor keys to select “SAVE” and
press ENTER.
5
Disconnect the YPAO microphone from
this unit.
Now optimization of the speaker settings is
complete.
Follow the procedure below to check the speaker
connections.
Depending on the type of speakers or room
environment, this message may appear even if the
speakers are connected correctly.
a Use the cursor keys to select “Result” and press ENTER.
b Use the cursor keys to select “Wiring”.
c Check the cable connections (+/-) of the speaker
indicated with “Reverse”.
If the speaker is connected correctly:
You can save the current settings.
Press RETURN and proceed to step 3.
If the speaker is connected incorrectly:
Turn off this unit, reconnect the speaker cable, and then
try YPAO measurement again.
• Since the YPAO microphone is sensitive to heat, do not place
the microphone in any place where it will be subjected to direct
sunlight or high temperatures (top of an AV equipment, etc).
If “W-1: Out of Phase” appears
© 2011 Yamaha Corporation YD507A0/ESEN2
Now let’s play back a BD/DVD.
We recommend playing back multichannel audio
(5.1-channel or more) to feel surround sound produced
by this unit.
1
Press AV1 to select “AV1” as the input
source.
2
Start playback on the BD/DVD player.
3
Press STRAIGHT repeatedly to select
“STRAIGHT”.
• When “STRAIGHT” (straight decode) is enabled, each
speaker produces each channel audio signal directly (without
sound field processing). If you play back 5.1-channel audio on
the 9.1-channel system, no sounds will be heard from the
surround back and front presence speakers. To check if
sounds are properly heard from all speakers, press STEREO
repeatedly to select “9ch Stereo”.
4
Press VOLUME to adjust the volume.
Now the basic setup procedure is complete.
Only the front speakers work on multichannel audio
Check the digital audio output setting on the BD/DVD
player.
It may be set to output 2-channel audio (PCM, etc.) only.
No sound is heard from a specific speaker
See “Troubleshooting” (p.139) in “Owner’s Manual”.
6 Playing back a BD/DVD
[ B ][ A ]
SOURCE
RECEIVER
AV
AUDIO
1 2 3 4
5 6 7
V-A UX
1 2 3 4
MULTI
PHONO
USB NET
TUNER
DOCK
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO STRAIGHT
INPUT
PURE
DIRECT
MUTE
TV
SCENE
1 2 3 4
PROGRAM
VOLUME
TV VOL
MUTE
MODE
TOP MENU
RETURN DISPLAY
POP-UP/MENU
TV CH
PRESET
ENTER
ON SCREEN
OPTION
[ B ]
[
A
]
SOU
R
CE
RECEIV
E
R
AV
AU
DI
O
2
3
4
5
6
7
V
-
AU
X
1
2
3
4
MU
LT
I
P
HO
N
O
US
B
NE
T
TUNER
DOC
K
AV1
STRAIGHT
STEREO
VOLUME
If you cannot have surround sound
OUT
1
IN
OUT
2
VOLUME
MUTE
DRCADAPTIVE
3
ZONE
2
STEREO
ENHANCER
SLEEP
HD
TUNED
PRE
AMP
PAR TY
ZONE
3
ZONE
4
HD
TAG
DOCK
SBLPL SBRSBPR
SW1
SL
SW2SW
SR
PL
CLR
PR
A.Sel:Auto
AV1
SPIMP.-
OUT
1
IN
OUT
2
VOLUME
MUTE
DRCADAPTIVE
3
ZONE
2
STEREO
ENHANCER
SLEEP
HD
TUNED
PRE
AMP
PAR TY
ZONE
3
ZONE
4
HD
TAG
DOCK
SBLPL SBRSBPR
SW1
SL
SW2SW
SR
PL
CLR
PR
A.Sel:Auto
STRAIGHT
SPIMP.-
OUT
1
IN
OUT
2
VOLUME
MUTE
DRCADAPTIVE
3
ZONE
2
STEREO
ENHANCER
SLEEP
HD
TUNED
PRE
AMP
PAR TY
ZONE
3
ZONE
4
HD
TAG
DOCK
SBLPL SBRSBPR
SW1
SL
SW2SW
SR
PL
CLR
PR
Main:Volume
SPIMP.-
Much more features!
This unit has various other functions.
Please refer to “Owner’s Manual” on the
supplied CD-ROM and utilize this unit
effectively.
Connecting other playback
devices (p.37)
Connect audio devices (CD player, etc.), game
console, camcorder, and many others.
Selecting the sound mode
(p.60)
Select the desired sound program (CINEMA
DSP) or surround decoder suitable for movies,
music, games, sports programs and other uses.
Playing back from iPod (p.70)
By using a USB cable supplied with iPod, an
optional Yamaha iPod dock or an optional
Yamaha iPod wireless system, you can enjoy
iPod music on this unit.
■ Listening to FM/AM radio (p.65)
■ Playing back music stored on a USB
storage device (p.77)
■ Playing back the network contents
(p.80 to p.83)
■ Selecting the input source and
favorite settings at once (p.58)
For more information, see “What you can do
with this unit” (p.6).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Yamaha RX-A3010 Manualul proprietarului

RX-A3010
Yamaha
Marca
Yamaha
Model
RX-A3010
Categorie
Receptoare AV
Tip
Manualul proprietarului
Descărcați PDF
raport

în alte limbi

Lucrări conexe