Yamaha P-105 Manualul proprietarului

Categorie
Pianele digitale
Tip
Manualul proprietarului

Acest manual este potrivit și pentru

P
-
1 0 5
D I G I T A L P I A N O
Owners Manual
EN
P-105 Owner’s Manual
2
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter).
DO NOT connect this product to any power supply or adapter other
than one described in the manual, on the name plate, or specifically
recommended by Yamaha.
WARNING: Do not place this product in a position where anyone
could walk on, trip over, or roll anything over power or connecting
cords of any kind. The use of an extension cord is not recommended!
If you must use an extension cord, the minimum wire size for a 25’
cord (or less ) is 18 AWG. NOTE: The smaller the AWG number, the
larger the current handling capacity. For longer extension cords, con-
sult a local electrician.
This product should be used only with the components supplied or; a
cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is
used, please observe all safety markings and instructions that accom-
pany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at
the time of printing. However, Yamaha reserves the right to change or
modify any of the specifications without notice or obligation to update
existing units.
This product, either alone or in combination with an amplifier and
headphones or speaker/s, may be capable of producing sound levels
that could cause permanent hearing loss. DO NOT operate for long
periods of time at a high volume level or at a level that is uncomfort-
able. If you experience any hearing loss or ringing in the ears, you
should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
Some Yamaha products may have benches and / or accessory
mounting fixtures that are either supplied with the product or as
optional accessories. Some of these items are designed to be dealer
assembled or installed. Please make sure that benches are stable and
any optional fixtures (where applicable) are well secured BEFORE
using.
Benches supplied by Yamaha are designed for seating only. No other
uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a
function or effect works (when the unit is operating as designed) are
not covered by the manufacturer’s warranty, and are therefore the
owners responsibility. Please study this manual carefully and consult
your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and envi-
ronmentally friendly. We sincerely believe that our products and the
production methods used to produce them, meet these goals. In keep-
ing with both the letter and the spirit of the law, we want you to be
aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if
applicable) is soldered in place. The average life span of this type of bat-
tery is approximately five years. When replacement becomes necessary,
contact a qualified service representative to perform the replacement.
This product may also use “household” type batteries. Some of these
may be rechargeable. Make sure that the battery being charged is a
rechargeable type and that the charger is intended for the battery being
charged.
When installing batteries, never mix old batteries with new ones, and
never mix different types of batteries. Batteries MUST be installed cor-
rectly. Mismatches or incorrect installation may result in overheating and
battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all bat-
teries away from children. Dispose of used batteries promptly and as
regulated by the laws in your area. Note: Check with any retailer of
household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some rea-
son its useful life is considered to be at an end, please observe all
local, state, and federal regulations that relate to the disposal of prod-
ucts that contain lead, batteries, plastics, etc. If your dealer is unable
to assist you, please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model
number, serial number, power requirements, etc., are located on this
plate. You should record the model number, serial number, and the
date of purchase in the spaces provided below and retain this manual
as a permanent record of your purchase.
Model
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
92-BP (bottom)
P-105 Owner’s Manual
3
Contents
Accessories............................................................. 3
About the Manuals .................................................. 4
PRECAUTIONS ...................................................... 4
Introduction
Panel Controls and Terminals 6
Setting Up 7
Turning the Power On/Off....................................... 7
Setting the Volume.................................................. 7
Using Headphones ................................................. 7
Connecting External Audio Equipment ................... 7
Using a Footswitch.................................................. 8
Using the Optional Pedal Unit................................. 8
Reference
Selecting & Playing Voices 9
Selecting a Voice .................................................... 9
Layering Two Voices (Dual).................................... 9
Splitting the Keyboard (Split) ................................ 10
Using the Pianist Styles ........................................ 10
Playing Duo........................................................... 11
Adding Variations to the Sound – Reverb............. 12
Setting the Touch Sensitivity................................. 12
Transposing the Pitch in Semitones ..................... 13
Fine-Tuning the Pitch............................................ 13
Listening to the Songs 14
Listening to the Demo Songs................................ 14
Listening to the Preset Songs ............................... 14
Using the Metronome/Rhythm 15
Selecting a Beat (Time Signature).........................15
Selecting a Rhythm ............................................... 15
Adjusting the Tempo..............................................15
Adjusting the Volume.............................................15
Recording Your Performance 16
Quick Recording .................................................... 16
Recording Independently to Two Parts .................16
Changing the Initial Settings of the Recorded Song
..17
Transferring SMF Files Between a Computer
and this Instrument ............................................17
Deleting the Entire Song........................................18
Song Playback and Practice 18
Backup Data and Initializing 19
Auto Power Off Function 19
Appendix
Troubleshooting 20
Specifications 20
Preset Song List 21
Quick Operation Guide 22
Accessories
Owner’s Manual
AC Power Adaptor*
Online Member Product Registration**
Footswitch
* May not be included depending on your particular area. Please check with
your Yamaha dealer.
** The PRODUCT ID on the sheet will be needed when you fill out the User
Registration form.
•Music Rest
Insert into the slot
Thank you for purchasing this Yamaha Digital Piano!
We recommend that you read this manual carefully so that you can fully take advantage of the advanced
and convenient functions of the instrument.
We also recommend that you keep this manual in a safe and handy place for future reference.
4
P-105 Owner’s Manual
In addition to this Owner’s Manual, the following Online materials (PDF files) are available.
Computer-related Operations
Contains instructions about computer-related functions.
MIDI Reference
Contains MIDI-related information, such as the MIDI Implementation Chart.
MIDI Basics (only in English, French, German and Spanish)
Contains basic explanations about what MIDI is and can do.
To obtain the documents above, access the Yamaha Manual Library, enter your model name in the Model Name
area, then click [SEARCH].
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Do not place the power cord near heat sources such as heaters or radiators. Also,
do not excessively bend or otherwise damage the cord, or place heavy objects on
it.
Only use the voltage specified as correct for the instrument. The required voltage
is printed on the name plate of the instrument.
Use the specified adaptor (page 20) only. Using the wrong adaptor can result in
damage to the instrument or overheating.
Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
This instrument contains no user-serviceable parts. Do not open the instrument
or attempt to disassemble or modify the internal components in any way. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as
water seeps into the instrument, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the instrument inspected by qualified
Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Do not put burning items, such as candles, on the unit. A burning item may fall
over and cause a fire.
When one of the following problems occur, immediately turn off the power switch
and disconnect the electric plug from the outlet. Then have the device inspected
by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the instrument.
About the Manuals
Power supply/AC power adaptor
Do not open
Water warning
Fire warning
If you notice any abnormality
DMI-5 1/2
5
P-105 Owner’s Manual
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
When removing the electric plug from the instrument or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
Remove the electric plug from the outlet when the instrument is not to be used for
extended periods of time, or during electrical storms.
Do not place the instrument in an unstable position where it might accidentally
fall over.
Before moving the instrument, remove all connected cables, to prevent damage
to the cables or injury to anyone who might trip over them.
When setting up the product, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even when the power switch is
turned off, electricity is still flowing to the product at the minimum level. When
you are not using the product for a long time, make sure to unplug the power
cord from the wall AC outlet.
Use only the stand specified for the instrument. When attaching the stand or rack,
use the provided screws only. Failure to do so could cause damage to the internal
components or result in the instrument falling over.
Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all components,
set all volume levels to minimum.
Be sure to set the volumes of all components at their minimum levels and
gradually raise the volume controls while playing the instrument to set the
desired listening level.
Do not insert a finger or hand in any gaps on the instrument.
Never insert or drop paper, metallic, or other objects into the gaps on the panel or
keyboard. This could cause physical injury to you or others, damage to the
instrument or other property, or operational failure.
Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
Do not use the instrument/device or headphones for a long period of time at a
high or uncomfortable volume level, since this can cause permanent hearing
loss. If you experience any hearing loss or ringing in the ears, consult a
physician.
Always turn the power off when the instrument is not in use.
Even when the [ ] (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level.
When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.
Notice
To avoid the possibility of malfunction/ damage to the product,
damage to data, or damage to other property, follow the notices
below.
Handling and Maintenance
Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Otherwise, the instrument, TV, or radio may
generate noise.
Do not expose the instrument to excessive dust or vibrations, or extreme cold or
heat (such as in direct sunlight, near a heater, or in a car during the day) to
prevent the possibility of panel disfiguration, damage to the internal components
or unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° –
104°F.)
Do not place vinyl, plastic or rubber objects on the instrument, since this might
discolor the panel or keyboard.
When cleaning the instrument, use a soft, dry/dry or slightly damp cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping
cloths.
Saving data
Some types of data (page 19) will be stored in internal memory, and maintained
even if the power is turned off. However, the data could be lost due to malfunction
or incorrect operation. Save important data to a computer. For details, refer to the
Computer-related Operations (page 4).
Information
About copyrights
Copying of the commercially available musical data including but not limited to
MIDI data and/or audio data is strictly prohibited except for your personal use.
This product incorporates and bundles computer programs and contents in which
Yamaha owns copyrights or with respect to which it has license to use others’
copyrights. Such copyrighted materials include, without limitation, all computer
software, style files, MIDI files, WAVE data, musical scores and sound recordings.
Any unauthorized use of such programs and contents outside of personal use is
not permitted under relevant laws. Any violation of copyright has legal
consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
About functions/data bundled with the instrument
Some of the preset songs have been edited for length or arrangement, and may
not be exactly the same as the original.
About this manual
The illustrations and LCD screens as shown in this manual are for instructional
purposes only, and may appear somewhat different from those on your
instrument.
The company names and product names in this manual are the trademarks or
registered trademarks of their respective companies.
Power supply/AC power adaptor
Location
Connections
Handling caution
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
DMI-5 2/2
P-105 Owner’s Manual
6
Panel Controls and Terminals
q [ ] (Standby/On) switch ....................... page 7
For turning the power on or setting to standby.
w [MASTER VOLUME] slider..................... page 7
For adjusting the volume of the entire sound.
e [DEMO/SONG] button ...........................page 14
For playing the Demo Songs and the Preset Songs.
r TEMPO [][]/SELECT [][]buttons
................................................................page 14
For selecting a Song during playback, adjusting the
tempo, and selecting the Song part for recording
and playback.
t [METRONOME/RHYTHM] button..........page 15
For starting or stopping the metronome or rhythm.
y [PIANIST STYLE] button .......................page 10
For using the Pianist Styles.
u [REC] button ..........................................page 16
For recording your keyboard performance.
i [PLAY] button ........................................page 16
For playing back the recorded performance.
o Voice buttons.......................................... page 9
For switching the Voice between those printed
above and below each button.
For selecting a Voice or two Voices played simulta-
neously, such as Piano and Organ.
!0 [USB TO HOST] terminal
For connecting to a computer, allowing you trans-
fer the User Song data as SMF, and transmit MIDI
messages between both devices. For details, refer
to the “Computer-related Operations” and the
“MIDI Reference.
!1 [SUSTAIN] jack........................................page 8
For connecting the included footswitch, an
optional footswitch and foot pedal.
!2 [PEDAL UNIT] jack ..................................page 8
For connecting an optional pedal unit.
!3 AUX OUT [L/L+R][R] jacks .....................page 7
For connecting external audio equipment.
!4 DC IN jack ................................................page 7
For connecting the power adaptor.
!5 [PHONES] jacks ......................................page 7
For connecting a set of standard stereo head-
phones.
!3 !4!2!1!0
!5
qwerty
ui o
C0 C1 C2 C3 C4 C5 C6 C7
A-1
Built-in Speakers
Speakers are built into the instrument at the bottom. Though you can
enjoy playing the instrument even when putting it on a desk or table,
we recommend that you use an optional keyboard stand for better
sound.
Shows the jacks and terminals as seen when viewed from the rear of the instrument.
• Use an AB type USB cable of less than 3 meters. USB
3.0 cables cannot be used.
NOTICE
Introduction
P-105 Owner’s Manual
7
Setting Up
1 Connect the AC power adaptor to the DC IN jack.
2 Plug the AC power adaptor into an AC outlet.
3 Press the [ ] (Standby/On) switch to turn on the
power.
The power lamp located to the left of the [ ]
(Standby/On) switch lights up. To turn off the
power, press this switch again.
When you start playing, use the [MASTER VOL-
UME] slider to adjust the volume of the entire key-
board sound.
I.A. Control (Intelligent Acoustic Control)
With this function, the sound quality of this instru-
ment is automatically adjusted and controlled accord-
ing to the overall volume. Even when the volume is
low, you can hear both low sounds and high sounds
clearly.
To turn on/off the I.A. Control:
While holding down [DEMO/SONG] and [MET-
RONOME/RHYTHM] simultaneously, press the
C#5 key to turn on or D5 to turn off. The default
setting is “on”.
To adjust the I.A. Control Depth:
While holding down [DEMO/SONG] and [MET-
RONOME/RHYTHM] simultaneously, press the
A#4 key to decrease by one, C5 to increase by one,
or B4 to reset to 0 (default). The setting range is
from -3 to +3.
For details on the key assignments, see “Quick Opera-
tion Guide” (page 22).
Since this instrument is equipped with two
[PHONES] jacks, you can connect two sets of stan-
dard stereo headphones. If you are using only one set
of headphones, insert a plug into either jack, shutting
off the speakers.
To amplify the instrument’s sound, you can connect a
stereo system to the AUX OUT [L/L+R]/[R] jacks via
the Phone plugs (standard). The volume of the sound
output from those jacks will be adjusted via the
[MASTER VOLUME] slider.
Turning the Power On/Off
• Use only the specified adaptor (page 20). Using the
wrong adaptor can result in damage to the instrument
or overheating.
• Even when the [ ] (Standby/On) switch is in standby
status (power lamp is off), electricity is still flowing to
the instrument at the minimum level.
When you are not using the instrument for a long time,
make sure you unplug the power cord from the wall AC
outlet.
• Note that the power is automatically turned off if this
instrument is not operated for 30 minutes. For details,
see page 19.
Setting the Volume
WARNING
CAUTION
AC power
adaptor
AC outlet
1
2
3
IMPORTANT
Increases.Decreases.
Using Headphones
• To protect your hearing, avoid listening with the head-
phones at a high volume level for long periods of time.
Connecting External Audio Equipment
• When the instruments sound is output to an external
device, first turn on the power to the instrument, then to
the external device. Reverse this order when you turn the
power off.
Use audio cables and adaptor plugs having no (zero) resistance.
Use only the [L/L+R] jack for connection with a monaural device.
Standard stereo
phone plug
CAUTION
NOTICE
NOTE
Setting Up
P-105 Owner’s Manual
8
The [SUSTAIN] jack is for connecting the included
footswitch, which works in the same way as a damper
pedal on an acoustic piano. Also an optional FC3 foot
pedal or FC4/FC5 footswitch can be connected to this
jack. The FC3 lets you use the Half Pedal function.
Half Pedal function (for FC3 and LP-5A/LP-
5AWH)
If you are playing the piano with sustain and want
a clearer, less muddled sound (especially in the
bass register), let up on your foot from the pedal to
half position or higher.
The [PEDAL UNIT] jack is for connecting an
optional LP-5A/LP-5AWH pedal unit. When connect-
ing the pedal unit, make sure to also assemble the unit
on an optional keyboard stand (L-85/L-85S/L-
85WH).
Damper (Right) Pedal
Pressing this pedal will sustain notes longer. Releas-
ing this pedal immediately stops (damps) any sus-
tained notes. A “half-pedal” function of this pedal
creates partial sustain effects, depending on how far
down you press the pedal.
Damper Resonance
This function simulates the sustain sound produced
via the damper pedal on a grand piano.
To turn on/off the Damper Resonance:
While holding down [DEMO/SONG] and [MET-
RONOME/RHYTHM] simultaneously, press the
G4 key (on; default) or G#4 key (off).
Sostenuto (Center) Pedal
If you play a note or chord on the keyboard and press
the sostenuto pedal while the note(s) are held, those
notes will sustain as long as you hold the pedal (as if
the damper pedal had been pressed) but all subse-
quently played notes will not be sustained. This makes
it possible to sustain a chord, for example, while other
notes are played “staccato.
Soft (Left) Pedal
The soft pedal reduces the volume and slightly
changes the timbre of notes played while the pedal is
pressed. The soft pedal will not affect notes that are
already playing when it is pressed.
Using a Footswitch
• Do not press the footswitch when turning the power on. Doing this changes
the recognized polarity of the footswitch, resulting in reversed footswitch
operation.
Make sure that power is OFF when connecting or disconnecting the foot-
switch or pedal.
Using the Optional Pedal Unit
Make sure that power is OFF when connecting or disconnecting the pedal unit.
The Damper Resonance cannot be used in Duo (page 11).
NOTE
LP-5A/
LP-5AWH
(optional)
L-85/L-85S/
L-85WH
(optional)
NOTE
When you select the JAZZ ORGAN or ROCK ORGAN Voice, the Left pedal func-
tions to switch the rotary speed of the rotary speaker.
If you press and hold the damper pedal here,
all the notes shown will be sustained.
G#4 (off)
G4 (on)
If you press and hold the sostenuto pedal here,
only the notes held at this timing will be sustained.
NOTE
P-105 Owner’s Manual
9
Reference
Selecting & Playing Voices
The instrument has a wide variety of Voices, or instru-
ment sounds, for your enjoyment, including Piano and
Organ.
1
Press a Voice button once or twice.
Pressing the same Voice button repeatedly alter-
nates the on/off status of the lamp, changing
between the Voices whose names are printed
above (lamp off) and below (lamp on) the buttons.
Voice List
2
Play the keyboard.
You can play Voices simultaneously across the entire
range of the keyboard. Note that the Voice of the left
side button is designated as Voice 1, while the Voice
of the right side button is designated as Voice 2.
1
Engage Dual.
Press the desired Voice button once or twice
(depending on the desired Voice), then while hold-
ing down that button, press the other Voice button
once or twice. When the lamp is off, the Voice
printed above the button is selected; when the
lamp is on, the Voice printed below is selected.
When the buttons are released, Dual is engaged.
The lamp indicates the status of the Voice 1 selec-
tion.
2
Play the keyboard to enjoy the dual
sound.
To shift the Octave for each Voice:
To shift Voice 1, simultaneously hold down
[METRONOME/RHYTHM] and press the A4
key to lower by one, B4 to raise by one, or A#4 to
reset to the default setting. For Voice 2, simultane-
ously hold down [METRONOME/RHYTHM]
and press the C5 key to lower by one, D5 to raise
by one, or C#5 to reset to the default setting. The
setting range is from -3 to +3 for both Voices.
Selecting a Voice
Voice Name Description
GRAND PIANO 1
Sampled from a concert grand piano. It
uses different samples depending on the
playing strength and produces smoother
tonal changes. Suitable not only for classi-
cal compositions but also for any style
music.
GRAND PIANO 2
Spacious and clear piano with bright
reverb. Good for popular music.
E. PIANO 1
An electronic piano sound created by FM
synthesis. Good for standard popular
music.
E. PIANO 2
A slightly brighter electronic piano sound
than E. PIANO 1. Good for standard popu-
lar music.
E. PIANO 3
Vintage electric piano sound of hammer-
struck metallic “tines.” Soft tone when
played lightly, and an aggressive tone
when played hard.
E. PIANO 4
Another vintage electric piano sound dif-
ferent from E. PIANO 3 often heard in rock
and popular music.
JAZZ ORGAN
A “tonewheel” type electric organ. Often
heard in jazz and rock music.
PIPE ORGAN
A typical pipe organ sound (8 feet + 4 feet
+ 2 feet). Good for sacred music from the
Baroque period.
ROCK ORGAN
Bright and edgy electric organ sound.
Good for rock music.
VIBRAPHONE
Played with relatively soft mallets. The
tone becomes more metallic the harder
you play.
STRINGS
Stereo-sampled, large-scale strings
ensemble with realistic reverb. Try com-
bining this Voice with piano in the Dual
mode.
HARPSI-
CHORD
The definitive instrument for baroque
music. Authentic harpsichord sound, with
plucked strings, no touch response, and
characteristic key-release sound.
WOOD BASS
An upright bass played fingerstyle. Ideal
for jazz and Latin music.
E. BASS
For a wide range of music styles, jazz,
rock, popular, and more.
Lamp
To familiarize yourself with the characteristics of the voices, listen to the
demo songs for each voice (page 14).
You can shift the Octave as described in the next column (see “Voice 1”).
Layering Two Voices (Dual)
Two Voices of the same button cannot be layered (for example, STRINGS and
HARPSICHORD).
NOTE
NOTE
Lamp
Voice 1 Voice 2
Voice 1 Voice 2
A4 D5
Selecting & Playing Voices
P-105 Owner’s Manual
10
To adjust the balance between two Voices:
While holding down [METRONOME/
RHYTHM], press the E5 key to decrease by one,
F#5 to increase by one, or F5 to reset to the default
setting. The setting range is from -6 to +6. Settings
above the default increase the volume of Voice1,
and vice versa.
3
To exit from Dual, simply press any
Voice button.
You can play different Voices your left and right
hands.
1
While holding [L], press a Voice button
to engage Split.
The Left Voice (Voice 2) is selected. The keyboard
is divided into the two sections with the F#2 key
as the Split Point.
2
To change the Right Voice (Voice 1) in
this status, select a Voice while holding
[R].
To shift the Octave for each Voice:
Same as in Dual (page 9).
To adjust the volume balance between two
Voices:
Same as in Dual (see column at left).
To change the Split Point:
While holding [L], press the desired key.
3
To exit from Split, simply press any
Voice button.
You can automatically play arpeggio-like rhythms by
specifying the chord type with your left hand, while
playing a melody with your right hand.
1
Press [PIANIST STYLE] so that the lamp
flashes.
The keyboard is divided into the Chord section
(Left) and Melody section (Right).
2
While holding [PIANIST STYLE], press a
key from the E2 – C#3 to select the
desired Style.
For details on which Pianist Style is assigned to
each key, see “Quick Operation Guide” (page 22).
Splitting the Keyboard (Split)
Only Dual or Split can be called up; both cannot be used together.
F#5 (+1)
E5
(-1)
F5
(Default)
Split Point (Default: F#2)
Left Voice (Voice 2) Right Voice (Voice 1)
NOTE
Using the Pianist Styles
Split Point (Default: F#2)
Chord section Melody section
C#3
E2
Selecting & Playing Voices
P-105 Owner’s Manual
11
3
Play a chord with your left hand to start
playback of the Pianist Style.
Play a melody with your right hand, along with
the chords you play.
To change the tempo:
Basically, this is the same as Metronome tempo
(page 15). In addition, you can change the tempo
also by pressing the specified keys while holding
[PIANIST STYLE]. For details about the key
assignment, refer to the Quick Operation Guide
(page 22).
To adjust the Pianist Style Volume:
While holding down [PIANIST STYLE], press
one of the A-1 – F#0 keys. The higher the key, the
higher the volume. The default value is 7 (D#-1).
4
Press [PIANIST STYLE] to stop
playback.
The lamp turns off, and the keyboard returns to the
original status.
To change the Split Point:
Same as in Split (page 10).
This function allows two different players to play the
instrument, one on the left and the other on the right,
over the same octave range.
1
While holding down [DEMO/SONG] and
[METRONOME/RHYTHM]
simultaneously, press the G6 key to
engage Duo.
The keyboard is divided into two sections, with
the E3 key as the Split Point.
2
One person should play the left section
of the keyboard while the other plays the
right.
To change the Left Voice:
While holding down [L], press a Voice button
once or twice.
To change the Right Voice:
While holding down [R], press a Voice button
once or twice.
To change the Right and Left Voices to the
same single Voice:
Simply press the Voice button once or twice.
To shift the Octave for each Voice:
Same as in Dual (page 9).
To adjust the volume balance between two
keyboard sections:
Same as in Dual (page 10).
Pedal function in Duo
The Footswitch connected to the [SUSTAIN] jack
affects both Right and Left sections. The optional
Pedal unit (page 8) functions as follows:
Damper Pedal: Applies Sustain to the right sec-
tion.
Sostenuto Pedal: Applies Sustain to both sec-
tions.
Soft Pedal: Applies Sustain to the left section.
3
To exit from Duo, press the G6 key while
holding [DEMO/SONG] and
[METRONOME/RHYTHM]
simultaneously.
For details on how to play Chords, refer to commercially available chord
books.
Refer to the numbers 1 – 10 printed in the VOLUME section above the
keyboard.
Playing Duo
NOTE
F#0
A-1
NOTE
The Split Point cannot be changed from E3.
If the keyboard is in Dual, engaging Duo will exit from Dual. The Voice 1
is used as the Voice of the entire keyboard.
Split Point
Left Voice (Voice 2) Right Voice (Voice 1)
Equivalent to C3 (middle C) Equivalent to C3 (middle C)
G6
NOTE
Selecting & Playing Voices
P-105 Owner’s Manual
12
This instrument features several Reverb Types that
add extra depth and expression to the sound to create a
realistic acoustic ambience. Although the appropriate
Reverb Type is called up automatically when you
select each of the Voices, Songs, and Pianist Styles,
you can change the Reverb Type.
To select a Reverb Type:
While holding down [METRONOME/RHYTHM],
press one of the G#6 – C7 keys.
Reverb Type List
To adjust Reverb Depth:
While holding down [METRONOME/RHYTHM],
press the F6 key to decrease by one, G6 to increase by
one, or F#6 to reset to the default value (most suitable
value for the current Voice). The higher the value, the
deeper the effect. The setting range is from 0 (no
effect) – 20 (maximum depth).
You can specify the degree of Touch Sensitivity (how
the sound responds to your playing strength).
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press one of the A6 – C7 keys.
Adding Variations to the Sound –
Reverb
Key
Reverb
Type
Description
G#6Room
Adds a continuous reverb effect to the
sound, similar to the acoustic reverbera-
tion you would hear in a room.
A6 Hall1
For a bigger reverb sound. This effect
simulates the natural reverberation of a
small-size concert hall.
A#6Hall2
For a truly spacious reverb sound. This
effect simulates the natural reverberation
of a large concert hall.
B6 Stage
Simulates the reverb of a stage environ-
ment.
C7 Off No effect is applied.
G#6
C7
F#6 (Default)
G6
(+1)
F6
(-1)
Setting the Touch Sensitivity
Key
Touch
Sensitivity
Description
A6
Fixed
The volume level does not change at all
regardless of whether you play the key-
board soft or hard.
A#6Soft
The volume level does not change much
when you play the keyboard soft or hard.
B6 Medium
This is the standard piano touch response
(default setting).
C7 Hard
The volume level changes very widely
from pianissimo to fortissimo to facilitate
dynamic and dramatic expression. You
have to hit the keys hard to produce a
loud sound.
The touch sensitivity settings may have little or no effect with JAZZ ORGAN,
ROCK ORGAN, PIPE ORGAN and HARPSICHORD–voices that are not normally
responsive to keyboard dynamics.
C7A6
NOTE
Selecting & Playing Voices
P-105 Owner’s Manual
13
You can shift the pitch of the entire keyboard up or
down in semitones in order to facilitate playing in dif-
ficult key signatures, or to easily match the pitch of
the keyboard to the range of a singer or other instru-
ments. For example, if “+5” is selected, playing key C
produces pitch F, letting you play a song of F major as
though it were in C major.
To transpose the pitch down:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press a key between F#3 (-6) and
B3 (-1).
To transpose the pitch up:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press a key between C#4 (+1)
and F#4 (+6).
To restore the original pitch:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press the C4 key.
You can fine tune the pitch of the entire instrument in
approximately 0.2 Hz increments. This lets you match
the keyboard pitch finely to that of other instruments
or CD music.
To lower the pitch:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press the C#0 key repeatedly to
lower the pitch in approximately 0.2 Hz increments.
To raise the pitch:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press the D0 key repeatedly to
raise the pitch in approximately 0.2 Hz increments.
To reset the pitch to the default (A3 = 440 Hz):
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press the B-1 key.
To set the pitch to A3 = 442 Hz:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM], press the C0 key.
Transposing the Pitch in Semitones
F#3
C4
F#4
Fine-Tuning the Pitch
• The setting range is from 427.0 Hz to 453.0 Hz. The default setting is A3 = 440.0
Hz.
C#0 (-0.2 Hz)
D0 (+0.2 Hz)
C0 (442.0 Hz)
B-1 (440.0 Hz)
NOTE
P-105 Owner’s Manual
14
Listening to the Songs
Special individual Demo Songs are provided for all of
the Voices of the instrument.
1
While holding down [DEMO/SONG],
press one of the desired Voice buttons
once or twice, then release the buttons
to start playback.
Pressing the same Voice button repeatedly alter-
nates the on/off status of the lamp, changing
between the Voices whose names are printed
above (lamp off) and below (lamp on) the buttons.
After selecting a Voice, release both buttons to
start playback. A Demo Song for each Voice will
play back in sequence (from left to right).
To change the Demo Song during playback:
Select another Voice. For details on selecting a
Voice, refer to page 9.
Press SELECT [] or [] to call up the previ-
ous or next Demo Song.
To adjust the playback tempo:
While holding down [METRONOME/
RHYTHM], press TEMPO [] or [] to
decrease or increase by one.
Demo Song List
The demonstration pieces listed above are short rearranged excerpts of the origi-
nal compositions. All other songs are original (© 2012 Yamaha Corporation).
2
Press [DEMO/SONG] again to stop
playback.
In addition to the Demo Songs, Preset Songs are pro-
vided for your listening pleasure. Choose a Song from
the Preset Song List on page 21, then follow the
instructions below.
1
While holding down [DEMO/SONG],
press one of the C2 – C#6 keys to start
playback.
Each of the Preset Songs is assigned to each of
these keys. For details on assignment, see “Quick
Operation Guide” (page 22).
The Preset Songs will play back in sequence.
To change to another Song during playback:
While holding down [DEMO/SONG], press one
of the C2 – C#6 keys.
•Press SELECT [] or [] to call up the previ-
ous or next Demo Song.
To adjust the playback tempo:
While holding down [METRONOME/
RHYTHM], press TEMPO [] or [].
2
Press [DEMO/SONG] again to stop
playback.
Listening to the Demo Songs
Simply pressing [DEMO/SONG] will start playback of all Demo Songs
from the first (Grand Piano 1) in sequence.
Voice Name Title
Composer
PIPE ORGAN
Herr Christ, der ein’ge Gottes-Sohn,
BWV.601
J.S. Bach
HARPSI-
CHORD
Concerto a cembalo obbligato, 2 vio-
lini, violae continuo No.7, BWV.1058
J.S. Bach
Lamp
NOTE
Listening to the Preset Songs
C2
1st
Song
10th
Song
20th
Song
30th
Song
40th
Song
50th
Song
C3 C4 C5 C6
P-105 Owner’s Manual
15
Using the Metronome/Rhythm
The Metronome is convenient for practicing with an accurate tempo. The Metronome sound features several
rhythms as well as the conventional click sound.
1
Press [METRONOME/RHYTHM] to start
the Metronome.
2
Press [METRONOME/RHYTHM] again to
stop the Metronome.
While holding down [METRONOME/RHYTHM],
press one of the A0 – D1 keys or one of the Voice but-
tons.
While holding down [METRONOME/RHYTHM],
press one of the E1 – C#2 keys.
For details on which Rhythm number is assigned to
each key, see “Quick Operation Guide” (page 22).
To increase or decrease the value by 1:
When the Metronome/Rhythm is playing back, press
TEMPO [] or []. When it is stopped, press
TEMPO [] or [] while holding down [METRO-
NOME/RHYTHM].
To increase or decrease the value by 1 or 10:
While holding down [METRONOME/RHYTHM],
press one of the D#4 – G4.
To reset the value to the default (120):
When the Metronome/Rhythm is playing back, press
both TEMPO [] and [] simultaneously. When it is
stopped, press both TEMPO [] and [] simultane-
ously or press the F4 key while holding down [MET-
RONOME/RHYTHM].
To specify a three-digit value:
While holding down [METRONOME/RHYTHM],
press a key of F3 – D4 one by one. For example, press
the F3 (0), D4 (9) and A#3 (5) keys in order to specify
“95.
While holding down [METRONOME/RHYTHM],
press the desired key between the A-1 (left-most key)
and F#0 key. The higher the key, the higher the vol-
ume. The setting range is from 1 – 10 and the default
value is 7.
Selecting a Beat (Time Signature)
When a Rhythm is selected, the Beat cannot be changed.
Selecting a Rhythm
*Refer to the “METRONOME” section printed above these keys.
A0 D1
No beat
2345
6
Beat
NOTE
E1
C#2
Adjusting the Tempo
Refer to the “TEMPO” section printed above these keys.
Adjusting the Volume
Refer to the “VOLUME” section printed above the keys.
* Refer to the “TEMPO” section printed above these keys.
D#4 (-10) F#4 (+1)
E4 (-1) G4 (+10)
F4 (Default)
NOTE
NOTE
P-105 Owner’s Manual
16
Recording Your Performance
You can record your keyboard performance as a User Song in SMF format. Up to two Parts (L and R) can be
recorded separately.
1
Before recording, make the settings
such as Voice and Beat.
Because some of the settings cannot be changed
after the Record mode is engaged, make the set-
tings according to your performance preferences.
For example, if you want to record your perfor-
mance with a Pianist Style, turn on [PIANIST
STYLE].
2
Press the [REC] to engage Record
Ready mode.
The [REC] lamp will flash according to the cur-
rent tempo. If necessary, set the tempo (page 15).
3
Play the keyboard or press [PLAY] to
start recording.
The [REC] lamp lights up while the [PLAY] lamp
flashes at the current tempo.
Play the keyboard and record your performance.
4
Press either [REC] or [PLAY] to stop
recording.
The [REC] and [PLAY] lamps flash, indicating
that the recorded data is being stored. After Store
is completed, the [REC] lamp turns off.
5
To hear the recorded Song, press [PLAY]
to start playback.
Press [PLAY] again to stop playback.
Part Assignment
When either the Pianist Style or Split/Duo is used
for recording, the data as listed below will be
recorded to each part.
You can record your performance to the L part (left
hand part) and R part (right hand part) separately.
1
Before recording, make the settings
such as Voice and Beat.
2
While holding down [REC], press [R] or
[L] for the part you want to record, to
engage Record ready Mode.
• Note that the Recording operation will replace the already
recorded data with the new data, since only one User Song
is available. Before recording, check the [PLAY] lamp
lights (data available) or not (no data). If you save the
recorded data, transfer it to the computer as a SMF file. For
details, refer to “Computer-related Operations” (page 4).
Quick Recording
You cannot engage Record mode while a song is playing.
You can use the Metronome/Rhythm while recording; however, the Met-
ronome/Rhythm sound will not be recorded. When you record the Pia-
nist Style performance, the Metronome/Rhythm cannot be played back
while recording.
NOTICE
NOTE
• Never turn off the power while the recorded data is
being stored (while the lamps are flashing). Other-
wise, all recorded data will be lost.
L part R part
When Pia-
nist Style is
on:
Chord change in the
left hand section
Keyboard perfor-
mance in the right
hand section
When Split or
Duo is on:
Keyboard perfor-
mance in the left
hand section
Keyboard perfor-
mance in the right
hand section
Recording Independently to Two
Parts
• If you select a Part containing data, the Recording opera-
tion will replace the already-recorded data with the new
data.
• If you want to record your performance using Pianist Style, Split or Duo, use the
Quick Recording method (in the previous section), since the instructions below
do not apply to these functions.
NOTICE
NOTE
Recording Your Performance
P-105 Owner’s Manual
17
To record the right part ([R]):
To record the left part ([L]):
After a while, the [REC] lamp will flash at the
current tempo. If necessary, set the tempo (page
15).
If data has already been recorded to the other
Part:
The data in this Part will be played back while
recording. This Part can be turned off or on by
pressing this Part button while holding down
[PLAY].
3
Start recording.
Play the keyboard or press [PLAY] to start record-
ing. The [REC] lamp lights up while the [PLAY]
lamp flashes at the current tempo.
4
Press either [REC] or [PLAY] to stop
recording.
The [REC] and [PLAY] lamps flash, indicating
that the recorded data is being stored. After the
operation is completed, the [REC] lamp will be
turned off.
5
If desired, record the other part by
repeating Steps 1 – 4.
6
To hear the recorded Song, Press
[PLAY] to start playback.
Press [PLAY] again to stop playback.
The following parameter settings of the Song can be
changed after the Record operation is completed.
For individual parts:
Voice, Balance, Reverb Depth, Pedal (Damper/
Soft)
For the entire Song:
Tempo, Reverb Type, Pianist Style Volume
1
Make the settings of the above
parameters.
2
While holding down [REC], press the
desired Part button to engage Record
Ready mode.
If you want to change the value of the parameters
shared by two parts, select either part.
3
Press [REC] again to change the initial
settings and to exit from Record Ready
mode.
With Musicsoft Downloader (available for free down-
loading), a SMF file can be transferred between the
computer and the User Song memory area of this
instrument. For details, refer to the “Computer-related
Operations” downloadable from Yamaha Manual
Library (page 4).
You can use the Metronome/Rhythm while recording; however, the Met-
ronome/Rhythm sound will not be recorded.
• Never turn off the power while the recorded data is
being stored (while the lamps are flashing). Other-
wise, all recorded data will be lost.
NOTE
Changing the Initial Settings of the
Recorded Song
• In this status, do not press [PLAY] again or any key.
Otherwise, recording starts and the data will be
deleted.
Transferring SMF Files Between a
Computer and this Instrument
• Before you transfer an SMF file from a computer, make sure
to transfer the User Song to a computer for safe keeping,
since already-recorded data will be replaced with the new
transfer.
NOTICE
Recording Your Performance
P-105 Owner’s Manual
18
1
Press [REC] to engage Record Ready
mode.
The [REC] lamp will flash.
2
While holding down [PLAY], press [REC]
so that both the lamps flash.
To exit from this status, press any other button
such as [DEMO/SONG].
3
Press [PLAY], [REC], [L] or [R] to delete
the data of the entire Song.
After the operation is completed, both lamps turn
off.
To delete a specific Part:
1
While holding down [REC], press [L] or
[R] to engage the Record Ready mode.
The [REC] lamp will flash.
2
Press [PLAY] to start recording without
playing the keyboard.
3
Press [REC] or [PLAY] to stop recording.
All data recorded for the selected Part will be
deleted, and the lamp turns off.
Song Playback and Practice
All the Songs except for the Demo (page 14) let you turn on or off the [L] and [R] parts individually. By turning
off [R], for example, you can practice the [R] part while the [L] part is playing back, and vice versa.
1
Start playback of the desired Song.
To start the User Song, press [PLAY]. To start the
Preset Song, press one of the C2 – C#6 keys to
start playback while holding down [DEMO/
SONG]. For details on what Song number is
assigned to each key, see “Quick Operation
Guide” (page 22).
2
While holding down [PLAY], press [L] or
[R] repeatedly to turn the Part on/off.
3
Practice the part which is turned off.
4
Press [PLAY] to stop playback.
Deleting the Entire Song
Selecting another Song will cancel the on/off status of the parts.
NOTE
P-105 Owner’s Manual
19
Backup Data and Initializing
The following data will be maintained as backup data
even if you turn off the power.
Backup data
Metronome/Rhythm Volume, Metronome/Rhythm
selection (Beat or Rhythm number), Touch Sensi-
tivity, Tuning, Split Point, Pianist Style Volume,
Auto Power OFF, Damper Resonance on/off,
I.A.Control on/off, I.A.Control Depth, User Song
To save the User Song data to a computer:
Among the backup data listed above, only the User
Song data can be transferred to a computer and saved
as a SMF file. For details, refer to “Computer-related
Operations” on the website.
To initialize the backup data:
While holding down the C7 key (right-most key), turn
the power on to initialize the backup data to the fac-
tory initial settings.
Both the [REC] and [PLAY] lamps flash, indicating
that the initialization is being executed. After the
operation is completed, both lamps turn off.
Auto Power Off Function
To prevent unnecessary power consumption, this function automatically turns the power off if no buttons or keys
are operated for approximately 30 minutes. If desired, you can disable or enable this function.
To disable Auto Power Off:
When the instrument is turned off:
While holding down the lowest key, press the [ ]
(Standby/On) switch to turn on the power so that the
power indicator flashes three times, after which the
Auto Power Off is disabled.
When the instrument is turned on:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM] simultaneously, press the A-1
key.
To enable Auto Power Off:
While holding down [DEMO/SONG] and [METRO-
NOME/RHYTHM] simultaneously, press the A#-1
key.
• Never turn off the power while the initialization is being
executed.
If this instrument somehow malfunctions or fails to operate properly, try execut-
ing the initialization.
C7
NOTICE
NOTE
A-1
A-1
A#-1
P-105 Owner’s Manual
20
Appendix
Troubleshooting
Specifications
Dimensions (W x D X H)
1,326 x 295 x 163 mm (52-3/16” x 11-5/8” x 6-7/16”)
Weight
11.7 kg (25 lbs. 13 oz.)
Keyboards
88 keys (A-1 – C7)
Graded Hammer Standard (GHS) keyboard
Touch Sensitivity (Hard/Medium/Soft/Fixed)
Voice
14 Preset Voices
Polyphony: 128
Effects/Functions
•4 Reverb types
Damper Resonance
•Dual
Split
•Duo
Intelligent Acoustic Control
Pianist Style
•10 Styles
Song Playback
14 Demo Songs + 50 Preset Songs
Song Recording
1 User Song with 2 tracks
Data Capacity: One song 100KB (about 11,000 notes)
•Format
Playback: SMF (format 0, format 1)
Recording: SMF (format 0)
Overall Functions
Transpose
Fine Tuning: 427.0 Hz – 453.0 Hz
Metronome/10 Rhythms
Tempo (5 – 280)
Connectivity
DC IN (12V), PHONES (2), SUSTAIN, PEDAL UNIT, USB TO
HOST, AUX OUT
Amplifiers
7 W + 7 W
Speakers
12 cm x 2 + 5 cm x 2
Power Supply
AC Power Adaptor PA-150 or an equivalent recommended by
Ya m a h a
Power Consumption
7W (When using PA-150 power adaptor)
Included Accessories
Owners Manual, Music Rest, AC Power Adaptor PA-150 or an
equivalent recommended by Yamaha*, Online Member Product
Registration**, Footswitch
* May not be included depending on your particular area.
Please check with your Yamaha dealer.
** The PRODUCT ID on the sheet will be needed when you fill
out the User Registration form.
Options
Keyboard Stand L-85/L-85S/L-85WH, Pedal Unit (LP-5A/LP-
5AWH), Foot Pedal FC3, Footswitch FC4/FC5, Headphones
(HPE-30/HPE-150), AC Power Adaptor (Users within U.S or
Europe: PA-150 or an equivalent recommended by Yamaha, Oth-
ers: PA-5D, PA-150 or an equivalent)
* Specifications and descriptions in this owner’s manual are for
information purposes only. Yamaha Corp. reserves the right to
change or modify products or specifications at any time without
prior notice. Since specifications, equipment or options may not
be the same in every locale, please check with your Yamaha
dealer.
Problem Possible Cause and Solution
The instrument does not turn on.
The instrument has not been plugged in properly. Securely insert the female plug into
the jack on the instrument, and the male plug into a proper AC outlet (page 7).
The instrument is automatically turned off even if
no operation is done.
This is normal. This occurs due to the Auto Power Off function (page 19).
Noise is heard from the speakers or head-
phones.
The noise may be due to interference caused by the use of a mobile phone in close
proximity to the instrument. Turn off the mobile phone, or use it further away from the
instrument.
The overall volume is low, or no sound is heard.
The Master Volume is set too low; set it to an appropriate level using the [MASTER
VOLUME] slider (page 7).
Make sure a pair of headphones is not connected to the headphones jack (page 7).
Make sure that Local Control is ON. For details, refer to “MIDI Reference” (page 4) on
the website.
The pedal has no effect.
The pedal cable/plug may not be properly connected. Make sure to securely insert the
pedal plug into the [SUSTAIN] or [PEDAL UNIT] jack (page 8).
The footswitch (for sustain) seems to produce
the opposite effect. For example, pressing the
footswitch cuts off the sound and releasing it
sustains the sounds.
The polarity of the footswitch is reversed because the footswitch was pressed when the
power was turned on. Turn off the power and turn it on again to reset the function. Make
sure to not press the footswitch when turning the power on.
1 / 1

Yamaha P-105 Manualul proprietarului

Categorie
Pianele digitale
Tip
Manualul proprietarului
Acest manual este potrivit și pentru